Search Documents

By M. Kanda, J. W. Adams

A system for measuring amplitude probability distributions (APD’s) of electromagnetic noise in coal mines is described and typical APD’s from an underground coal mine are presented. The APD is a basic statistic required for the design and analysis of communication systems, especially those intended for use in noisy environments, and where neither overdesign nor underdesign is acceptable. The rms and average field strengths are obtained by integration of the APD, and examples are shown at several frequencies. All field strength levels are given in absolute units. Selected frequencies cover the range from 10 kHz to 32 MHz.

Jan 1, 1973

By E. D. Gardner

This paper discusses prospecting for lode gold and lists the principal lags and. regulations pertaining to locating; lode claims on public lands. It is a preprint of a part of a bulletin being prepared by the United States Bureau o Mines entitled "Equipping, Developing and Operating Small Gold Mines". The increased interest in gold mining manifested during the past few years (1932-1935) bas stimulated prospecting. Many adventurers have taken to the field to search for now gold deposits. A. large percentage of them have had no previous experience in prospecting for lode gold; this paper has been written with the tope that it might assist these newcomers.

Jan 1, 1935

By Robert H. Schutz

This publication lists and describes devices approved jointly by the Secretary of Interior and the Secretary of Health, Education, and Welfare, under the provisions of [§]70.300-1, Part 70, Subchapter 0 of Chapter I, Title 30, Code of Federal Regulations (35 F.R. 5548, April 3, 1970), for use as respiratory protection against respirable pneumoconiosis-producing dusts. Included are type C supplied-air respirators approved under Bureau of Mines Schedule 19R and dust, fume, and mist respirators approved under Bureau of Mines Schedule 21B.

Jan 1, 1971

Illinois has the largest reported bituminous coal resources of any state and is one of largest coal-producing states in the nation. Coal-bearing rocks underlie about 65 percent of Illinois, including all or part of 86 of its 102 counties. An estimated 18 1 billion tons of coal resources are still in the ground. Using present mining methods, more than 30 billion tons of coal are classified as recoverable. This represents almost one-eighth of the total recoverable reserves of all types of coal in the United States. The state's surface mining regulatory program was conditionally approved June 1,1982. It received full approval October 25,1988. The Abandoned Mine Land Program was approved June 1, 1982, and the AML emergency authority June 11, 1984.

Jan 1, 1992

The objectives of this research were to examine and to laboratory performance of several brands of rigid urethane een brands, produced by 13 manufacturers, were examined. was performed in a laboratory under controlled conditions. document the foam. Eight-All testing Preliminary laboratory tests included flame spread evaluations, flame penetration, ignition temperatures, air permeability, and adhesion. Having established arbitrary cutoff values, the original 18 candidates were narrowed to 8. More specialized tests followed. The effects of water immersion and dry aging on flame spread performance and other physical properties were then examined. This Bureau of Mines report was written to provide information for those concerned with using rigid urethane foam as a sealant. Its intent is to describe the various laboratory evaluations performed and to delineate the performance of each candidate. This report neither promotes nor discourages the use of rigid urethane foams. It presents results that will enable those responsible for using or enforcing the use of rigid urethane foams in underground mines to make informed decisions.

Jan 1, 1985

By Fred Kissell

The Bureau of Mines has developed the shearer-clearer--a new type of dust control system for longwall shearers. The system partitions the airflow around the shearer into a clean split and a contaminated split. The dust cloud is confined to the vicinity of the coal face, while the shearer operators remain in the clean split on the gob side of the machine. The shearer-clearer operates on the principle that each water spray moves air like a small fan and can be positioned to direct the dusty air towards the face. The hardware is inexpensive and can be installed in a single shift. It consists of several strategically mounted water sprays and one or more passive barriers. Laboratory testing indicates reductions 1n shearer operator dust exposure as high as 97 pct. Preliminary results from an underground demonstration in one mine also indicate that considerable dust reductions at the shearer may be obtained. In conjunction with the development of the shearer-clearer, dust surveys were conducted in three other mines to determine if some shearer spray systems currently in use partition the flow in a manner similar to the shearer-clearer, and if so, whether this partially accounts for markedly cleaner conditions on some longwalls. Results from these surveys indicate this to be the case. A feature of the cleaner longwalls was a downwind orientation of their water sprays, which is a key element of the shearer-clearer system. The shearer-clearer system described in this report was designed for an Eickhoff EDW 300 shearer working a 7-foot coal seam. The testing to date has concentrated on cutting directions counter to the primary airflow. The development effort continues for different mining equipment and conditions. It is expected that different systems will be required to accommodate the range of conditions occurring underground. Application of the system presented here to conditions different than those described is not likely to produce the same results.

Jan 1, 1981

By H. H. Fields, Joseph Cervik, G. N. Aul

Coal is a soft and brittle material. Drilling rates in the Pittsburgh coalbed using a drag bit exceed 3 ft/min at 2,500-pound thrust. However, maintaining the bit on a horizontal trajectory or parallel to bedding planes to attain lengths of 1,000 feet is difficult. This Bureau of Mines report presents a drill string configuration that can be guided through the coalbed. The angle of the borehole is measured periodically and by proper combinations of bit thrust and rotational speed (r/min), bit trajectory can be lifted or dropped to keep the bit in the coalbed. An example of a hole drilled to 2,126 feet is presented to show levels of thrust and rotational speed used to lift or drop the bit, the seemingly unexplainable events that occur, and the strategy used during drilling. Thrust levels during drilling range from 600 to 2,500 pounds. Hydraulic motors powered by a 30-hp, 440-volt motor provide ample power for drilling horizontal holes 2,000 feet long.

Jan 1, 1975

By J. W. Thompson

"The ordinance of March 27, 1919, contains provisions relative to the exploration for, Ind the exploitations of bauxite in the Colony of Surinam in Dutch Guiana.Permission to explore is limited to: Netherlanders; inhabitants of the Netherlands; inhabitants of Surinam; companies established in Netherlands, and companies established in Surinam.Holders of concessions for the exploitation of bauxite are limited to companies established in the Netherlands, or in Surinam, and these must reside in the Colony or must be represented the constantly.A permission or concession lapses: (a) when the holder ceases to have the required qualifications; (b) on the death of the holder where the assigns fail within one year to prove the required qualifications.Any dispute concerning the required qualifications must be decided by the Judge in the manner to be regulated by colonial ordinance.The Governor may, after consultation with the Privy-Council reserve tracts of land for the exploration and exploitation of Bauxite, either for the Government directly, or for concession under special provisions. These provisions shall be fixed by virtue of the colonial ordinances.Application for permission to explore shall be made in accordance with existing laws. Simultaneous applications, those made on the same day, must be decided by drawing lots; but an application for the concession for exploitation has preference ovor that for permission for exploration. On notice of objection to the drawing of lots, the Governor may in his discretion, declare the drawing null and void and order a re-drawing."

May 1, 1920

By McHenry Mosier

The diamond-drill method was tried at the site selected for driving a 5- by 6 -foot air shaft at the east end of the Bellefonte mine . This method of sinking consisted , first , of drilling a 5-3/4 -inch-diameter cut hole from the surface , then drilling parallel 1.5 - inch ( EX ) holes around it at appropriate distances for a balanced blasting round . The cut hole was not charged with explosive but served as a relief chamber for the incipient expansion of the ground broken by. blasting the surrounding 1.5 - inch holes . The length of each hole was 236 feet , which was the finished depth of the shaft . The nature of the work in the air shaft was largely experimental , and many difficulties arising from the lack of special equipment and proper technique for precise alinement of the drill holes caused expensive delays before they could be overcome . Drilling the 5-3 /4 - inch hole , which was impeded by frequent core blocks in the core barrel , required 10 shifts . average advance per shift for an EX hole was about 150 feet . The The holes were charged and fired from the surface . The length of the section blasted in one cycle was 10 feet . Blasting progressed from the bottom of the shaft upward . The broken stone dropped into a chute , from which it was drawn into cars on the haulage level . The Bellefonte mine is an underground limestone mine.3/ The primary objective in undertaking the research on shaft sinking by diamond drilling was to perfect a method for driving connections between levels of the mine .

Oct 1, 1948

By Joseph W. Town

The Bureau of Mines conducted studies related to SO2 air pollution to determine attritioning rates, SO2 sorption rates, and sulfur loads that could be obtained on commercial alkalized alumina sorbent pellets. Fluidized-bed attritioning rates ranged from 0.025 pct/hr for alkalized alumina with a crushing strength of 4 kg to 0.075 pct/hr for 0.5 kg crushing strength mate¬rial. Airlift attritioning rates ranged from 0.50 pct/hr for 3 kg crushing strength alkalized alumina to about 3 pct/hr for 0.5 kg material. Attritioning rates for the commercial alkalized alumina were comparable to those obtained for sorbent pellets prepared in the Bureau of Mines laboratory. Sorption rates were related to S02 concentration in flue gas, temperature, and presence of nitrogen oxides in the gas stream. Sorption rates at 300° C were 0.35 X 10-6 gS/gp/sec (grams sulfur per gram pellet per second) in 0.045 pct so, gas, 5.1 x 10-5 gS/gp/sec in 0.34 pct SO2 gas, and 65 X 10-5 gS/gp/sec in 10 pct SO2 gas. For the 0.34 pct S02 gas, sulfur loads of 0.10 gS/gp (the projected load for regeneration) were obtained in 47 min at 130° C and in 116 min at 300° C. The presence of either NO or NO2 in the 0.34 pet S02 gas increased the SO2 sorption rates 2 to 3 times at 300° C, but had no effect at 130° C.

Jan 1, 1969

By V. Castranova, K. Van Dyke

"I. INTRODUCTIONA mechanism which is present in leukocytes and capable of releasing histamine from rabbit platelets was first described by Barbaro and Zvaitler in I966. A soluble mediator between rabbit leukocytes and platelets was also detected by Siraganian and Osier in 1971. This factor was isolated and characterized in 1971 by Benveniste et al. and named platelet activating factor i PAF). It was shown to be released from rabbit basophils through an antigen - IgE-dependent mechanism. The presence of PAF in human leukocytes' and its aggregation and releasing effects on human platelets were also demonstrated. Chemical analysis has shown that PAF is a glycerophospholipid with a choline polar head group. an ester-linked acyl chain at the second carbon and a nonester link at the first carbon.' The structure of the mediator was found to be 1-O-alky1-2-acetyl-sn-glyceryl-3-phosphoryl choline and it has been chemically synthesized.""' A variable portion exists in the alkyl group attached to the first carbon which can have a variety of molecular sizes such as C and C (where Cu is more abundant). Recent work by Pinckard et al."" has shown that there are at least five variations of the alkyl group.PAF has been shown to have a broad range of biological effects. Release of PAF from alveolar macrophages may be important in asthma, allergy, and shock states. In a rabbit model of antigen IgE anaphylaxsis. PAF can induce all of the effects of antigen challenge and. therefore is presumed to be a key mediator in production of anaphylaxsis. In addition to aggregating and degranulating platelets it is a potent chemoattractant."" and causes contraction of guinea pig ileum contraction of lung tissue and enhanced capillary permeability PAF has important effects in the kidney and is also known as the renal hypotensive factor proposed by Blank et al. who found the structure of PAF independently of Benveniste et al.' In producing these responses. PAF acts by a receptor-like mechanism. In platelets. PAF selectively desensitizes itself but not thrombin or collagen. In smooth muscle tissues a similar phenomenon occurs with anaphylatoxin or other stimuli.In vivo. PAF probably acts in concert with other agents in producing its various biological effects. It causes platelets to release histamine serotonin and RCS (rabbit-contractile substance formed from prostaglandins PPG2, PGH2 and TXA2) which contracts rabbit aorta. PAF can cause cells to release SRS-A and leukotriene B."

Jan 1, 1989

By F. H. Nehl

Ion elutriation was used to extract silver cyanide complexes and free cyanide from aqueous streams containing up to 10 ppm silver and 5 ppm free cyanide. Screening tests selected nine of 350 different surfactants for further, larger scale experiments. The screening procedure used 0.1 g of each of the surfactants in 300 mL of synthetic wastewater. Air was sparged into the test cell at 50 cc/min. The foam was refluxed during the tests and was not sampled. Samples of the solution were taken at specified intervals and analyzed by wet chemical methods for free cyanide and by atomic absorption for silver content. The most effective surfactants lowered the silver and free cyanide concentrations to less than 0.5 ppm in 1 h or less. These surfactants were quaternary amine salts with one long chain (C12-C18) organic group and three methyl groups. Experiments using 3 L batches of wastewater or an ion elutriation cell continuously fed with solution draining from an inactive heap leach operation confirmed the results from the screening tests.

Jan 1, 2010

By Oliver Bowles

"Rhodesian asbestos is of high quality and is much in demand by American consumers. Production in Rhodesia was first reported in 1909. The production for this and each succeeding year is shown in the following table:The serious curtailment in production for the years 1912 and 1913 was occasioned by transportation difficulties. In 1914 a railway was projected to Victoria and thereafter production increased greatly. Up to 1916 asbestos was obtained,from the Victoria district only, but thereafter the Bulwayo district became an important,producer with minor quantities from Gwelo.In the Bulawayo district the productive area is about 2 1/2 miles long, with Shebanie mine at the north-west end, the Nil Desperandum at the south end, and the Birthday claims between them."

Oct 1, 1920

By J. R. Long

The investigations described herein are concerned with a portion of a systematic research, by the Federal Bureau of Mines on ductile titanium. The Bureau's work on the metal has resulted in development of a semi commercial process for the preparation of titanium and has also made available significant information on the fabrication and physical properties of this new strong, light, corrosion-resistant metal. Considerable interest has been aroused by this work, and a number of other laboratories have begun similar investigations. However, the necessity for Consolidating titanium by normal powder metallurgy methods presents difficulties in producing commercial forms and shapes on a large scale. This investigation was therefore undertaken for the purpose of improving the technique for consolidation of titanium powder into solid nonporous metal.

Jan 1, 1949

1. Alford, N.G. quantity, of timber used in soft-coal mines and how much will be needed for the future. Gives a table of estimated increase in mine timber consumption in the future. A.I.M.E. Separate. 1336-C 1924. 2 Clark, B.M. The forest and the mine. Rept. Conference of Wood-Using Industries, Harrisburg, Pennsylvania. Apr. 13-14, 1921, pp. 58-62. Describes experience of a Pennsylvania mining company in depletion of timber supply and conservation methods adopted.

Jan 1, 1925

By Kathleen J. D?Amico

This summary appears in Minerals Year- book volumes I-II, and III, which cover mineral production in the United States, its island possessions, the Canal Zone, and the Commonwealth of Puerto Rico, as well as the principal minerals imported into and exported from the United States. The sections of this chapter and the area chapters in volume III contain further details on production. A summary table comparing world and U.S. mineral production also is included. Mineral production may be measured at any of several stages of extraction and processing. The stage of measurement used in the chapter is normally what is termed "mine output." It usually refers to minerals in the form in which they are first extracted from the ground, but customarily includes for some minerals the product of auxiliary processing operations at or near mines.

Jan 1, 1970

By Earl L. Phillips

The Bureau of Mines conducted laboratory tests on samples of pozzolanic-cement concrete to develop a low-strength backfill. Results show that support costs can be lowered by replacing a portion of the portland cement in mine backfill with pozzolan (fly ash) and lime. Unconfined compression tests on various ratios of fly ash to cement in 84 samples produced compressive-strength curves that can be used to estimate the best backfill mix for any mine.

Jan 1, 1981

By Seth C. Schaefer

[As part of the Bureau of Mines effort to provide thermodynamic data for advancement of mineral resources technology, the standard Gibbs energies of formation (?G°f) of MnS (manganese sulfide) and Fe0.9 S (pyrrhotite) were investigated with a high-temperature galvanic cell employing stabilized Zr02 (zirconia) as the electrolyte. Potential measurements were obtained for the cell Pt, MnS, MnO, S02 (g, 1 atm)//Zr02//02(g, 0.0114 atm), Pt with the overall cell reaction MnS (s) + 1.5 02 (g, 0.0114 atm) = MnO (s) + S02 (g) . (1) These results give the standard Gibbs energy of formation of MnS for the reaction Mn (s) + 0.552 (g) = MnS (s) (2) ?G°f = -66.487 + 15.19 x 10-3T±0.207 kcal/mole (896.4 - 1,208.1 K) (3) where temperature (T) is expressed in kelvins. Similar measurements were obtained for the cell Pt, FeO .9S, Fe304 , S02 (g, 1 atm) //Zr02//02 (g, 0.0114 atm) , Pt with the overall cell reaction 10/3 FeO .9 S (s) + 16/3 02 (g, 0.0114 atm) = Fe.,04 (s) +10/3 S02 (g). (4) These results yield the standard Gibbs energy of formation for the reaction 0.9 Fe (s) + 0.5 S2 (g) = Fe0.9 S (s) (5) ?G°f = -35.229 + 12.67 x 1073T+-0.104 kcal/mole (839.5 - 1,086.6 K). (6) A third-law analysis of MnS data yields a standard enthalpy of formation (AH°f) for the reaction Mn (s) + S (rh) = MnS (s) (7) ?H°f298 = -51.16±0.21 kcal/mole (8) A similar third-law analysis for Fe0.9S data yields a ?29°f298 for the reaction 0.9 Fe(s) + S(rh) = FeO .9S(s) (9) ?HO\°f298 = -24.01±_0.15 kcal/mole. (10) ]

Jan 1, 1980

By Terry S. Cory

This report covers magnetic field strength measurements vs range and frequency in low-medium coal mines. Both quasi-conductor-free and conductor-proximity areas were investigated. The program covered 5 mines, 4 seams, 6 measurement sets, and 3 geographic areas. The results have been summarized in terms of maximum communication range expected per seam and noise condition. Scatter gain is further explored as a simple measure of energy coupled to conductors.

Jan 6, 1978

By W. D. Walker

All pipelines used to transport liquid fuels over coal mines are potentially hazardous; however, this publication deals only with dangers in transporting gasoline. Since transporting gasoline by this method is an established practice, the hazards connected therewith should he recognized by coal-mine operators and pipeline companies so that every known precaution may be used to reduce and keep the hazards to a minimum. The purpose of this paper is to direct the attention of coal-mine operators and employees, pipeline-company officials, and other interested persons to the explosion and fire hazards that arise from seepage of gasoline into underground mines. A hazard is not only presented in an individual mine when gasoline enters underground workings; but, in cases where mines are interconnected, a hazard exists in mach such mine.

Jan 1, 1954