Search Documents

By Leonard Obert

Subsidence to surface occurs in a large proportion of underground mines. Preliminary to any indication of subsidence on the surface, there is usually a breaking up and sloughing of the cover into the mine opening which, in a period of time ranging from minutes to many years, progresses to the surface, This process is referred to as subsurface subsidence. In many mining operations, information regarding the process of subsurface subsidence is important, For example, if there are buildings or other improvements on the surface, or if the direction of the subsurface subsidence might threaten other underground workings--such as shafts--or if the subsidence might be progressing in a direction which would fall outside the anticipated subsidence limits, the problem could assume special significance.

Jan 1, 1961

By D. K. Steele

The domestic primary copper industry generates in excess of 600 million t of mining and mineral-processing waste annually. Most of the waste poses negligible environmental threat, but a small fraction, because of toxic or corrosive characteristics, may be subject to regulation under Subtitle C of the Resource Conservation and Recovery Act (RCRA) or other pertinent regulations. Among the wastes generated by various copper producers are flue dusts, slags, refinery-bleed solutions, and. acid-plant wastes. The U.S. Bureau of Mines (USBM) has researched methods to mitigate the environmental threat posed by copper-processing wastes while recovering valuable metals from these materials. Acid-leach processing of flue dusts has been demonstrated feasible along with sulfide treatment of liquid refinery wastes and acid-plant-bleed and gas-cleaning solutions to precipitate dissolved metals. In, addition, the feasibility of removing copper and molybdenum from slag, as well as stabilization of precipitated sulfide wastes by vitrification, have been investigated.

Jan 1, 2010

By William T. Reid

Low-temperature carbonization of coal in Japan served as an important source of liquid fuels during the war. Six plants operating in Japan Proper produced 203,069 KL (53.7 million gallons) of liquid fuel from 1940 until the end of the war in August 1945, while four additional plants in Karafuto and Korea produced 211,943 KL (56.0 million gallons) for a total of 415,012 KL (109.7 million gallons) of liquid products. Semicoke produced in these plants was used for domestic fuel, for gasi- fication in portable gas producers on automotive vehicles, and to replace imported low-volatile bituminous coal in the manufacture of metallurgical coke. Since 1936 one plant had produced more than 300,000 metric tons of semicoke for blending with bituminous coal to form coke, while the total production of semicoke since the beginning of the industry in 1923 is approxi- mately 2,000,000 metric tons. Despite an apparent annual carbonizing capacity of about 2,000,000 metric tons of coal for the entire country, the maximum amount of scmicoke produced during the peak year, 1943, was 468,446 metric tons. The equipment used is primarily of Gorman design. Just before the end of the war, 6 plants using 20 Lurgi carbonizers were operating with a total rated capacity of more than 1,500,000 metric tons of coal per year, while 2 Koppors units had a combined annual rated capacity of 400,000 metric tons of coal. One plant using the Japanese-designed Mimura system was in service but with so much mechanical trouble that its output was small, while in another plant 4 Wanisht carbonizers of Japanese design but based on an early German development were running satisfactorily, and carbonizing about 100,000 metric tons of coal per year. A single installation of 15 American-designed Knowles ovens was operating near Tokyo but was carbonizing pitch for electrode carbon. ..! No true low-temperature process used in Japan could carbonize strongly. caking coals satisfactorily. The Mimura process designed for this purpose was unsuccessful, as was the Shimomura process before it, while the Lurgi, Koppers, and Wanishi systems operated only with noncaking or very weakly caking coals. The Knowles ovens, really a medium-temperature process, could carbonize-caking coal without difficulty...

Feb 1, 1948

By Paul C. Hyndman

The U.S. Bureau of Mines inventoried Federal mineral lands in Idaho and classified them in detail, section by section, according to their availability for mineral exploration and development as affected by legal restrictions and agencies' management practices. The Bureau also identified known mineral deposit areas (KMDAs) and areas conducive to oil, gas, and geothermal resources. This information is shown on maps (developed in part by geographic information system technology) that spatially compare the availability for mineral entry of Federal land with these KMDAs to demonstrate the extent and severity of restrictions on mineral entry. Idaho contains 53.1 million acres, 35.7 million (67%) of which is Federal mineral land. About 7 million acres of this land is within KMDAs that host medium-to high-value locatable mineral deposits; 36% of this land is available, 27% is slightly to moderately restricted, and 37% is severely restricted or unavailable. For the leasable minerals, about 1.8 million acres are within KMDAs that host medium-to high-value phosphate deposits, about 5.4 million acres are favorable for oil and gas resources, and 3.9 million acres for geothermal resources. The percentages of land availability are 30%, 45%, and 25% for the phosphate acreage, 38%, 34%, and 28% for the oil and gas acreage, and 43%, 30%, and 27% for the geothermal acreage.

Jan 1, 2012

By Elton L. Litchfield

The Bureau of Mines determined minimum energies for direct initiation of expanding gaseous detonation waves in acetylene-oxygen mixtures. Composition limit ranges for the initiation of detonation with fixed energies have been compared to data in the literature. Assuming that the stored electrical energy is completely converted to thermal energy, the agreement between the energy of primary explosive initiators and the energy of electrical discharge initiators was good. Minimum energies for initiation of detonation in the most sensitive composition (40 percent C20 plus 60 percent 0 2) were: 0.64 joule at an initial pressure of 1/4 atmosphere, 5.0X10-2 joule at 1/2 atmos¬phere, and 3.7X10-3 joule at I atmosphere. Fuel concentrations in mixtures initiated to detonation by 4.9X102 joules ranged from 10 to 65 percent C2H2 at 1/4 atmosphere, 10 to 67 percent C2H2 at 1/2 atmosphere, and 9 to 68 percent C2H2 at 1 atmosphere.

Jan 1, 1967

By Maria I. De Rosa

Table 19 and figure 7 show the number of fires and fire injuries for surface coal mines by state during 1990-1999. Table 19 also shows by state the risk rates, employees' working hours, lost workdays, and coal production. For surface coal mines, 215 fires occurred in 21 states during 1990-1999. Ninety-four of those fires caused 93 injuries and I fatality (the yearly average was 21.5 fires and 9.3 fire injuries). Fourteen fires and seven injuries involved contractors. The Ewhr value was 729 x 10° hr (In = 0.026), the CP value was 6,355 x 10° st (Fn = 0.034), and the LWD value was 8,141. Kentucky had the most fires and fire injuries (45 fires and 23 injuries), followed by Pennsylvania (33 fires and 14 injuries), West Virginia (25 fires and 14 injuries), and Indiana (20 fires and 8 injuries). Among these states, Pennsylvania had the highest fire risk rate value (Frr=0.145), while Kentucky had the highest injury risk rate value (In 0.041).

Jan 1, 2004

By H. C. Hamontre

[The Bureau of Mines well-bore caliper was designed to provide an instrument that could be operated through 2-inch tubing, which 'a used particularly in many input wells on water-flooding projects of eastern, Kansas and northeastern Oklahoma. It should find wide application elsewhere under many other conditions where it has not been possible previously to make caliper logs with the larger probes used on other instruments. The caliper has three additional advantages over other instruments of this type: (1) It measures 4 radii (up to 18 inches) 90° apart with an accuracy of ± 1/4 inch; (2) the measuring arms can be opened and closed at will by remote control; and (3) it is run and operated on a single-conductor, armored electric cable (Amergraph, type 1-H-0). The caliper probe is 1-3/4 inches in diameter and approximately 6 feet in length. The electrical control and measuring circuits are encased in a stainless-steel tubular case. Measuring arms, made of 5/16-inch aluminum tubing, are attached near the lower end of the instrument. Distances the arms are extended are indicated t the surface by a meter calibrated to read directly in inches. Depths at which the radii measurements are taken are indicated by a wireline depth indicator on the cable-reeling. The instrument is not affected by pressure or temperature, it can be run open hole or under pressure through a lubricator. This paper describes and illustrates the instrument and outlines the operating procedures. A bibliography at the end of the report gives references to articles and patents on the development and use of other well-bore calipers.]

Jan 1, 1954

By D. B. Starkey

Investigation into the expressions of the field produced by a loop over a conducting half space or in an infinite conducting half space are well documented. Reasonably complex descriptions of the effects of stratification also are reported. However, a model which must contain all of these complexities because of transmission to depths of 15,000 feet and also include the pertibation of the field by a verticle cylindrical steel casing loses its facility in the field or for quick, accurate approximation to field magnitudes and phase. This paper describes the results of two field tests to determine the attenuation and phase versus depth and frequency of an electromagnetic wave (induction field). A simple two-layer model is postulated to predict the magnitude and phase of the induced field which does not require sophisticated computing tools. Correlation of the model with experimental results show agreement of most amplitude measurements to within 3 db and most phase measurements to within five degrees. The tests were conducted in a 7400 foot deep well in Nevada and an 11,000 foot deep well in Wyoming which had conductivities ranging from .0025 mhos/m to .25 mhos/m. The surface transmitting dipole had an area of ~ 10 6 feet squared and constant frequency signals of 1.5 Hz to 20 Hz were transmitted through the earth utilizing less than 65 watts of power. Model Description The magnetic field intensity components generated by a magnetic dipole immersed in an infinite homogeneous medium can be expressed in spherical coordinates as: [ ] where N, I, and (p a ) are the transmitting antenna turns, current, and effective area, respectively, and r is the range from the loops circumference to the measurement point. The case of interest for these experiments, however, is the special case of coaxial dipoles, i.e., ? = 180° . For this case H?= 0 and H reduces to: [ ]

Jan 1, 1973

Objective To identify techniques to reduce the probability of gob gas explosions. Background In the last 6 years, seven explosions of methane and/or coal dust occurred within worked-out, sealed areas (gobs) of underground U.S. coal mines. These explosions, believed to have been started by lightning, destroyed many mine seals and caused much damage external to the sealed area. Three of these gob gas explosions occurred in one mine in Alabama over a 3-year period. Fortunately, the explosion forces and the toxic gases that vented from the sealed gob area did not cause fatalities or injuries, but they destroyed several large seals. If miners had been inspecting or working near these areas, the potential for serious injury and/or death would have been high. The United Mine Workers of America and the Mine Safety and Health Administration (MSHA) requested that the National Institute for Occupational Safety and Health (NIOSH) help identify the mechanisms for lightning penetration into the gob and recommend ways to reduce the probability of occurrence of future explosions from such lightning penetrations into sealed areas of underground coal mines. Because three of the explosions occurred in a single mine, special attention was focused on these particular explosions. The first occurred in April 1994 in a sealed area, which enclosed about 1.35square miles of abandoned workings (gob). This explosion destroyed 3 of the 38 seals that surrounded the gob. These seals were less than 2,000 ft away from three 4.5-in-diam steel-cased test wells that extended from the surface into the mine entry. At the time of the explosion, the National Lightning Detection Network (NLDN)verified 12 lightning strikes within 10 miles of the mine, including several above the gob. After the 1994 explosion, the damaged seals were rebuilt using an acceptable seal design capable of with standing a 20-psi explosion, as required by 30 CFR 75.335. On January 26,1996, a second gob explosion destroyed five more cementitious pumpable seals less than 2,000 ft away from those destroyed in 1994and even closer to the steel-cased wells. The NLDN verified72 lightning strikes in the area of this second gob explosion. Compressive strength analyses of fragments from the destroyed seals showed that strengths ranged from 11 to 138 psi, with an average of83 psi. This is over 100 psi below the minimum 200-psi compressive strength requirement for cementitious pumpable seals. These seals were again replaced. On July 9, 1997, the third and most violent explosion occurred in the same vicinity of the last two explosions. Three more cementitious pumpable seals were destroyed, including one newer seal that exceeded the minimum 200-psi compressive strength requirement. The NLDN verified 695 lightning strikes above the mine during the time in which the explosion occurred. MSHA's

May 1, 2001

By P. B. Altringer

Searles Lake, CA, contains the largest known domestic tungsten resource. The brines in this near-dry lake bed, located in the Mojave Desert 130 mi northeast of Los Angeles, contain an estimated 135 MMlb of tungsten. However, the low concentration of tungsten (0.080 g/L W03) in the supersaturated brine makes selective tungsten extraction very difficult. Although many brine chemicals are extracted from the lake, tungsten recovery was an elusive goal prior to Bureau of Mines development of an ion-exchange technique. This publication describes the Bureau process. The following subjects are ad-dressed: ? The Searles Lake tungsten resource. ? General problems associated with tungsten recovery. ? Bureau research objectives. ? Synthesis of ion-exchange resins. ? Development of a two-stage ion-exchange tungsten extraction and concentration procedure. ? Product recovery and purification. ? Economic evaluation. Flowsheets for recovering three products (calcium tungstate, sodium tungstate, and tungstic oxide) are presented and evaluated, as well as a summary of the research effort and potential applications.

Jan 1, 1985

By K. C. Dean

This report is the first of a series concerned with processes for producing magnesium. These reports will evaluate metallothermic, carbothermic , and electrolytic production methods, and will furnish a cost basis for comparing the processes. Areas deemed most promising for future research will be delineated for each procedure. This report presents briefly the history of the metallothermic process, and describes the operations of the Defense Plant Corp. (DPC) plants that employed the process. A hypothetical plant designed to produce 12,000 tons of magnesium per year, using ferrosilicon as a reductant, is described, and raw materials, energy, and major equipment requirements are estimated. Several process modifications are suggested for future research.

Jan 1, 1965

By J. M. Goris

The U.S. Bureau of Mines is conducting research on cable bolt ground supports to assess their material and support properties, to provide design criteria for using cable bolt supports as roof control systems under various types of underground mining conditions, and to provide a mathematical model of cable bolt support systems. Part 1 describes laboratory studies of the support properties of cable bolts made of conventional steel cables and provides recommendations on such topics as the use of thick grouts, selection of breather tubes, and reduction of water bleeding in cement-based grouts. The studies evaluated both single and double cables; effects of different embedment lengths, water-cement ratios, and grout curing temperatures on support strength; effects of use or nonuse of breather tubes; pumpability and water-bleeding properties of grouts; and the strength properties of sand-cement grouts. Part 2 will cover the strength characteristics of birdcage cable bolt supports, epoxy-coated cables, and cables with steel buttons attached.

Jan 1, 1990

By M. Mentser

The exchange of oxygen between carbon dioxide and carbon monoxide that occurs reversibly on carbon surfaces was studied at temperatures of 750° to 850°C and a pressure of 1 atmosphere. Carbon-14 was used to detect and measure the exchange reaction. The extent of oxygen exchange was a linear function of com- position of the gas mixture, and this relationship was used to evaluate the forward and backward rate constants of the reaction. Equilibrium constants, directly determined for oxygen exchange in this study, agreed well with values in the literature that were derived only by indirect procedures. This result establishes the validity of oxygen exchange in the mechanism of carbon gasification by CO2. Rates of carbon gasification were less than an order of magnitude slower than rates of oxygen exchange. Activation energies for these two processes were 58 and 53 kcal/mole, respectively. The closeness in the activation energies argues against any change in the rate-controlling step over a wide temperature span at atmospheric pressure. The role of CO as a retardant on the CO2-C reaction, and the nature of the carbon-oxygen complex are also discussed in view of the data obtained.

Jan 1, 1973

By Otto L. Schumacher

The Overthrust Belt in portions of Montana, Idaho, Utah, and Wyoming, an area that has contributed generously to the Nation's mineral supply, is one of the few remaining oil and gas frontiers on the North American continent. Determination of the oil and gas potential and development of mineral resources of the area have been affected by a variety of land withdrawals and other restrictions, The purpose of this study is to determine the extent of these withdrawals and restrictions and to discuss the mineral resource potential within the study area. Statistics in this report refer to land status on January 1, 1979. At that time, of the 27.3 million acres of Federal mineral lands within the study area, applications tor Federal oil and gas leases for more than 4,4 million acres (about 16 percent) were pending; the average length of time was 2 years. Federal oil and gas leases covering 8.8 million acres were also on record. Although drilling has occurred on some of these leases, others are subject to restrictions that discourage or prevent development. Some in fact contain stipulations disallowing any development.

Jan 1, 1981

By L. A. Morley

Volume III of the final report examines the indication versus interruption procedures used on motion-drive power equipment, with emphasis on surface excavators. The report begins with a review of the electromechanical acid conversion used with the Ward-Leonard control system. Protection criteria for the drive-system components are then discussed. Fault sources and fault calculations for both the ac supply source and dc power loop are introduced to assist in discussing indication and interruption procedures. The subject is then expanded to examine the dynamic process of the machine and determine the effects of fault current and position of the machine to allow for an orderly shutdown. With this analysis, possible indication an interruption procedures are given for the four-quadrant duty cycle of excavators. The report concludes by introducing other mining operations that utilize similar motion-drive systems and also static (solid-state) drives and recommends further research in these areas, as well as a more detailed examination of the dynamic fault analysis for excavators.

Jan 1, 1982

This volume contains a series of papers describing research conducted by the Bureau of Mines to develop or improve equipment and systems that satisfy the communication requirements of miners doing work related to rail, belt-conveyor, trackless, and hoist haulage systems.

Jan 1, 1977

This part of the final report treats some problems related to coal mine carrier frequency communication systems using the trolley wire/track transmission line. This work was undertaken for a brief period of time during the summer of 1972 to help understand, quantify, and improve some of the trolley wire carrier system behavior observed and/or predicted. Calculations and estimates of transmission line characteristic impedance, inductance and capacitance per unit length, mine motor loading effects, parallel line effects, and connection impedances are presented in Chapter I. Chapter II treats the design of r-f isolators for reducing the undesired and troublesome r-f loading that mine motors present to the trolley transmission line. Chapter III treats a diversity method for combatting standing wave nulls. I. CALCULATIONS RELATED TO TROLLEY WIRE COMMUNICATIONS A. ESTIMATION OF INDUCTANCE AND CAPACITANCE PER UNIT LENGTH OF TROLLEY LINES To estimate the L and C per unit length of trolley lines, we use the eccentric line model of Section G of this Chapter, "Characteristic Imped¬ance Estimates for Mine Trolley Lines." The capacitance per unit length for an eccentric line is given by (1)

Jan 1, 1974

By N. N. Moelbs

The U.S. Bureau of Mines is conducting research on many topics relating to the hazards of coal mining, increased production, and protection of the environment. One area of research that has received scant attention in recent years is that of water inflows, probably because few fatalities in the United States have been attributed to them. As mining goes deeper, the problem of water in 1ow could increase dramatically because of adjacent or overlying mines in which huge water pools are impounded. Inaccurate mine maps and ineffective barriers can constitute a serious problem for operators both from gradual inflows and sudden inrushes of water. This report describes a wide but ineffective barrier that permitted an average 240-gpm inflow to a developing mine from an adjacent mine. The anomalous geologic structure that facilitated this leakage is described, demonstrating that size, alone, is no assurance against serious leakage. Some recommendations for managing serious water inflow are included.

Jan 1, 1989

By L. H. ADAMS, C. N. HASKINS, J. K. CLEMENT

In the course of its investigations of the fuel resources in the United States and of the methods by which these resources could be utilized with greatest efficiency, the United States Geological Survey tested a great variety of coals and lignites as gas-producer fuel. Early in these testa it was found that many factors controlling the formation of gas in the generating chamber of the producer and, consequently, having a direct bearing on the management of producer-gas plants, were not as well understood as they should be. The Geological Survey therefore took up a detailed investigation of the chemical and physical processes that take place in the producer, keeping in view not only the possibility of increasing the efficiency of the producer as a source of energy, and the ensuing benefits to the public of cheaper power and greater utilization of low-grade fuels, but also the application of the results to the problems of boiler-furnace operations. - The Bureau of Mines, to which the testing and analyzing of fuels as carried on by the United States Geological Survey has been transferred, is continuing producer-gas investigations at the testing station at Pittsburg, Pa. Results of the gas-producer tests a made at the coal-testing plant erected at St. Louis, Mo., and of a study of some of the problems° that came up in the tests have been published by the Geological Survey. Results of the tests made at Norfolk, Va., and Pittsburg, Pa., and of further studies of particular problems, will be published by the Bureau of Mines. In the gas producer solid fuel is transformed into more readily combustible gaseous fuel. The transformation is relatively slow and consists of several processes: 1. The distillation of the volatile hydrocarbons from the freshly fired fuel at relatively low temperatures. 2. The combustion of the fuel by its combining with the oxygen of the air forming carbon dioxide (COO. 3. The formation of carbon monoxide (CO) and hydrogen (11 3), the essential constituents of producer gas, in accordance with the equations:

Jan 1, 1911

By Charles S. Allbright

To develop a method for predicting the stability of a fuel during long-term storage from rapid aging tests at 200° F, the Bureau of Mines determined the stabilities of three gasoline base stocks and an alkylate blending stock in both sealed storage and aerated storage at 110° F for periods extending to 32 weeks. Stabilities of samples containing gasoline-additive compounds were compared by aging, using two methods--rapid aging in a bomb at 200° F for intervals up to 16 hours and storage at 110° F. The additives used were an uninhibited tetraethyllead motor mix, N,N'-di-sec-buty1-p-phenylenediamine and 2,6-di-tert-butyl-4-methylpheno1. Results were related by graphs that enable predictions of gum and sediment formation during storage from data obtained in bomb tests. A premium-gasoline base stock and the alkylate proved to be stable, but the two regular-grade gasoline base stocks were found to be unstable. Addition of the diamine antioxidant improved the stability of both of the regular gasoline base stocks, while the phenol antioxidant improved only one of them. The presence of the tetraethyllead decreased the storage stability of all four fuels, both with respect to formation of gum and precipitation of inorganic sediment. The rapid test at 200° F appears to offer promise as a basis for a method of predicting gasoline stability in long-term 110° F storage.

Jan 1, 1968