Search Documents

By W. N. Marchant

The Bureau of Mines performed chemical research to elaborate details of sulfur chemistry pertaining to the citrate flue gas desulfurization process in which sulfur dioxide (SO2), absorbed (as bisulfite ion) in a buffered sodium citrate solution, is reduced by hydrogen sulfide (H2S) according to the overall reaction 2H2S + HSO3 + H+ ? 3S + 3H20. The rate-limiting step in the process was shown to be the reduction by H2S of thiosulfate (S2031-) that is formed as an intermediate. Pseudo first-order kinetic measurements were made at room temperature to retard the reaction sufficiently that adequate analysis was possible. These measurements showed the rates of the following net processes to be -d [S02]/dt (pH 4.5) = (0.409±0.050)min-1 [S02]; d [S2032-]/dt (pH 4.5) = (0.199±0.017)min-1 [S02]; -d [S2032-]/dt (pH 4.0) = (0.0437±0.0265)min-1 [S2032-]~1; -dH2S/dt (pH 3.9) = (21.6±3.0) mmoles/min-atm [H2S]g1.4, where [H2S]g is the partial pressure of H2S in the gas phase, in atmospheres, and the rate describes the consumption of H2S, in millimoles per minute; d[S]/dt (pH 4.0) = (38.0±3.4)min-1 [H2S]1, where [H2S] is the concentration of H2S in solution. Hydrogen ion consumption during the slow phase of regeneration was shown to occur at (2.1±0.5) times he rate of thiosulfate consumption, which is interpreted as evidence for the following as the rate-limiting reaction: 2H2S + S2032- + 2H+ ? 4S + 3H20 A scheme consisting of five sequential general reactions is proposed to account for sulfur formation.

Jan 1, 1981

By J. E. Chilton

Underground miners may be exposed to hazardous quantities of toxic gases, such as carbon monoxide (CO), generated from mine fires or explosions. Every underground miner is required to carry a filter self-rescuer (FSR), which when operated will remove CO from the miner's breathing air. In addition, every underground miner must have a self-contained self-rescuer (SCSR) near the worksite that will supply breathing oxygen. In many situations, miners do not know when to don either rescuer since they do not know if there is a fire in the mine, nor do they carry instrumentation necessary for the detection of the toxic, colorless, and odorless fire product CO. If each miner carried a personal CO alarm, which would respond to high concentrations of CO, the miner would then be alerted when to don either the FSR or SCSR and exit the mine. A prototype personal miner's CO alarm called PEMCOAL was developed by the U.S. Bureau of Mines. The PEMCOAL unit is small enough to be carried on a miner's belt, has a flash lamp visual alarm, requires no calibration for use, and uses a chemical sensor that changes color by reaction with trace quantities of CO. The chemical sensor was tested at concentrations of CO from 10 to 1,000 ppm, at temperatures from 5° to 40° C, and with several potential mine gas interferents. The PEMCOAL alarm times were sufficiently fast to warn miners before they are exposed to hazardous quantities of CO.

Jan 1, 1989

By Albert W. Deurbrouck

The preparation characteristics of the coals of Buchanan County, Va., are described in this Bureau of Mines report. Twenty-one samples ,,,ere collected from 9 coalbeds in the county. Of these samples 13 were of metallurgical quality as received, and 8 required some upgrading to provide acceptable products. In general, the coals were of low to medium ash and sulfur content, and ranked as medium-to high-volatile bituminous. In 1963, production in the county was in excess of 13 million tons, of which 2.2 million tons were mechanically cleaned.

Jan 1, 1966

By Gary L. Hundley

The Bureau of Mines has devised and demonstrated an ammoniacal sulfate leach process for recovering nickel and cobalt from low-grade domestic laterites. Solvent extraction of cobalt, one of the process steps, requires the reduction of hexammine complexes of C03+ to C02+ in an ammo-niacal leach solution. Previously, reduction was accomplished using cobalt metal shot in a column. This report presents experimental results and an economic evaluation comparing two alternate techniques with the shot column: (1) an electrolytic reduction cell with an extended surface area cathode and (2) direct electrowinning from purified leach solution using a cell with a fluid bed cathode. The second alternative eliminates the conventional solvent extraction-electrowinning steps. The costs of the three methods, based on the requirements of a pro-posed commercial-sized plant, including all unit operations, were deter-mined by the Bureau's process evaluation group. The operating costs for the shot column, $1.19/kg Co, and for electrolytic reduction, $1.20/kg, are essentially the same, but the cost of direct electrowinning, $3.77/ kg Co, would eliminate this method as a practical alternative. The cap-ital cost of approximately $14.4 million for reduction in a shot column is much higher than the approximately $4.4 million for electroreduction.

Jan 1, 1985

By Thomas M. Barczak

This U.S. Bureau of Mines report describes methods to enhance the capacity, stiffness, and timber utilization of wood crib supports. Since stiffer supports minimize strata deflections that contribute to roof instability, efforts to maximize crib stiffness while maintaining stability through a wide displacement range should be a design priority. The stiffness and capacity of conventional crib designs, employing alternating layers of wood timbers that are loaded perpendicular to the grain, can be increased by increasing the interlayer contact area or by using higher strength wood. Contact area can be increased by using wider timbers or employing more timbers per layer. Concepts that provide parallel-to-the-grain timber loading will provide substantial increases in crib stiffness and capacity. Two concepts that utilize this principle are examined: (1) an original South African design that constructs wood cribs from preformed layers (mats) of timber where short blocks are oriented vertically between horizontal slabs; and (2) a design that employs full lengths of timber placed vertically in the interior of a conventional crib structure. These designs also provide more efficient timber utilization by providing greater support capacity per volume of wood used in the crib construction.

Jan 1, 2010

By Benjamin W. Haynes

As part of the first-order assessment of potential manganese nodule processing reject waste materials, the Bureau of Mines estimated the physical and chemical characteristics of reject waste materials that would be generated from each of five potential process flowsheets. These processes were chosen because of their economic and technical feasibility for first-generation nodule processing. A brief description of the five processes is given to show process inputs and outputs, The physical characteristics are predicted based on land-based laterite processing where applicable, and where no land-based analog exists, on the basis of process chemistry. The probable chemical characteristics such as element content and compound form are tabulated for each process for 16 elements: As, Ba, Be, Cd, Go, Cr, Cu, Fe, Mn, Mo, Ni, Pb, Sb, Se, TI, and Zn. These elements were chosen based on their presence on the toxic substance list of priority pollutants, EP toxicity criteria, and major and minor elements of economic importance (Co, Fe, Mn, and Mo). Physical and chemical analyses as well as results of the EP toxicity test of one industrially supplied pilot plant reject waste material are presented.

Jan 1, 1982

By Bruce Cantrell, K. L. Rubow

"INTRODOCTIONMeasurement of the contribution of diesel exhaust to respirable aerosol in mine environments has become increasingly important because of current concerns over the occupational health effects resulting from exposure to diesel emissions. In response to this, the U.S. Bureau of Mines is developing and evaluating new sampling methods for measuring diesel aerosol in underground mines. Two such techniques are being studied by the Bureau, size selective sampling and Chemical Mass Balance (CMB) modeling. These techniques use measurable physical or chemical characteristics of a mine aerosol sample to infer the amount of diesel particulate material contained in the sample.Size selective sampling is being adapted for measurement of diesel aerosol by the Particle Technology Laboratory (PTL) of the University of Minnesota under sponsorship by the Bureau. 1 It is based on the premise that diesel and mineral dust aerosol can be physically separated by size and collected during sampling using inertial impaction. An independent effort by the National Institute for Occupational Safety and Health to develop a size selective sampling technique was also sponsored by the Bureau.The second technique, CMB modeling, is being developed by the Bureau as an alternative measurement technique to referee the results obtained using size selective sampling.3 It compares measured trace element ""finger prints"" of aerosol sources with similar profiles of mine aerosol samples. From these, the portions of the sample contributed by each source can be determined. Results of these investigations in underground coal mines have confirmed that diesel and coal dust aerosol are of different size and can be measured separately using size selective sampling techniques.A major difference in diesel usage among underground mines is the requirement for exhaust gas cooling systems in coal and gassy noncoal mines. Nongassy mines usually employ limited exhaust conditioning in the form of catalytic converters, which have limited effect on primary exhaust particulate. The cooling system in most general use in gassy mines is the water scrubber. This device has little effect on most of the gases but removes particulate material from the exhaust. 5 Because of this, exhaust aerosol characteristics in nongassy mines are expected to be different. To see if size selective sampling techniques can be used in such mines, the Bureau and the University of Minnesota conducted a second study in three metal and nonmetal mines, two nongassy and one rated as gassy."

Jan 1, 1990

By C. C. Hwang

The Bureau of Mines made time-dependent calculations to determine the size of a stationary source fire within a ventilated duct (or passage-way) necessary to ignite a combustible duct liner. The objective of this work was to gain more understanding of what occurs in duct fires and to determine critical conditions for ignition and propagation of mine fires. Heat transfer to the combustible surface includes both convective and radiated components, while the heat is conducted into the combustible and reradiated to the surroundings. The combustible is assumed to ignite when the net heat transfer to its surface is sufficient to raise the surface temperature to some minimum temperature, defined as the ignition temperature. A nondimensional parameter, which characterizes the source-fire intensity in the presence of ventilation flow, emerges as a parameter for a criterion of the critical conditions. The results of these calculations indicated that the minimum fire size necessary for ignition increases with the ventilation rate and duct cross section. These results are compared with experimental results obtained from fires in a 0.8-by 0.8-by Il-m-long duct and a full-scale gallery (2.4-by 2.4-by 65-m). Agreement between the theory and the experiment is good.

Jan 1, 1988

By A. Gene Collins

Rapid, sensitive, and precise methods of determing major, minor and trace constituents of oilfield brines are needed. Several methods have been developed or adapted by the Federal Bureau of Mines at the Petroleum Research Center, Bartlesville, Okla. The following methods are described in this report: Spectrophotometric and volumetric for iodides and bromides; potentiometric for pH, alkalinity, acidity, borate boron, total boron, and organic boron; gravimetric for potassium; disodium ethylenediaminetetraacetate (EDTA) volumetric for total hardness, calcium, and magnesium; spectrophotometric for fluorides; and color comparison .for arsenic. Adequate sensitivity, precision, and accuracy were obtained for each method. The Bureau of Mines pioneered in research on the analysis of oilfield waters (2, 46, 47).6 However, several of these early procedures were quite time consuming. Also, they did not include methods for determining trace and minor constituents of brines.

Jan 1, 1961

By Dennis S. Kostick

Salt is a universal mineral commodity used by virtually every person in the world. Although a very common mineral today, at one time, it was considered as precious as gold in certain cultures. This study traces the material flow of salt from its origin through the postconsumer phase of usage. The final disposition of salt in the estimated 14,000 different uses, grouped into several macrocategories, is traced from the dispersive loss of salt into the environment to the ultimate disposal of salt-base products into the waste stream after consumption. The base year for this study is 1990, in which an estimated 196 million short tons of municipal solid waste was discarded by the U.S. population. Approximately three-fourths of domestic salt consumed is released to the environment and unrecovered while about one-fourth is discharged to landfills and incinerators as products derived from salt. Cumulative historical domestic production, trade, and consumption data have been compiled to illustrate the long-term trends within the U.S. salt industry and the cumulative contribution that highway deicing salt has had on the environment.

Jan 1, 1993

By John J. Henn

As part of the U.S. Department of the Interior programs on rutile, authorized by the Office of Emergency Preparedness in June 1967 under provisions of the Defense Production Act, the Bureau of Mines reviewed available literature on major proposed processes for producing rutile substitutes. The processes are grouped according to the major processing step, and important operating features are described. Sixty-one references are cited.

Jan 1, 1970

By E. A. Barrett

The U.S. Bureau of Mines (USBM) conducted experiments to determine if training using a latent-image, three-dimensional (3-D) slide simulation exercise improved miners' ability to recognize roof and rib hazards. The effectiveness of this innovative type of classroom training was investigated by measuring workers' performance on a hazard recognition task. The study was unique in that hazard recognition skills were assessed in the workplace using actual coal mine roof and rib hazards. Results showed that training with a latent-image, 3-D slide simulation exercise significantly improved each subject's performance on the in-mine hazard recognition task. Further, the USBM researchers concluded that transfer of learning from the classroom to the workplace occurred.

Jan 1, 2010

By Ann C. Kim

This Bureau of Mines report summarizes the methods and results of many of the laboratory studies on spontaneous heating of coal published in the last 50 years. It includes a brief description of experimental methods, indices of combustibility, and important contributing factors. Adiabatic calorimetry, isothermal calorimetry, [0], sorption systems, or temperature differential are the most frequently used experimental methods. Indices of combustibility include various heating rates, crossing point temperature, ignition temperature, and CO index. Factors that affect the spontaneous heating of coal include air flow rate, changes in moisture content, particle size, rank, temperature, pyrite content, geological factors, and mining practice. Experimental conditions and results from 20 papers are summarized in an appendix, and the bibliography contains 45 references.

Jan 1, 1977

By RUSSELL S. DAVIES, Andrew Allan, John W. Buch

This is a progress report for the period February 1, 1949, to August 15, 1949, covering experiments with lightweight shearing machines for developing thin, steeply pitching anthracite beds. The over-all objective at the time an underground test section was established on July 30, 1946, was to improve mining above the gangway by developing methods for mechanization of pitch mining. Following the preliminary cutting tests in the gangway with the German machines, it became evident that the use of machines of this type indicated advantages for development work that could not be overlooked and warranted investigation. An agreement was reached with the cooperating company that this be done. Thus, the objectivo in the period covered by this report has been to obtain operating data to uso in comparing hand and machine methods of driving development openings. In obtaining the machine-mining data, 78 feet of gangway, 108 feet of heading, and 80 foot of chute work were driven. Hand-mining data are authentic for the mining condition. It has been shown that full mechanization is two and one-half times as fast as conventional hand methods on a lineal-feet- advance-per-shift basis and costs but little more than one-third as much. Tho machines are air-powered; there is less shattering of the coal bed by blasting; water sprays are used to allay' dust; coal is loaded by machine; no rock is taken; timber is not dislodgod by heavy blasting charges; and it may be said, except for the development of a means for transporting timber to the face, that the tasks for the miner are less arduous, and the working face equally as safe, or safer, than in driving by hand. Face timbering remains the greatest time- consuming cycle item, and steps are being taken to correct this. More than 50 percent of the cycle time is now usod for face-timbering work.

Jul 1, 1951

By Thomas M. Barczak

This Bureau of Mines report describes research on developing technology to utilize shields as roof load monitors. Three-dimensional equations of static quilibrium are presented for a generic two-legged long-wall shield. The equations are presented in the most general form, assuming a force and moment vector at each reaction by rigid-body analysis of the shield mechanics. The resulting system of equations was found to be indeterminate to a very high degree. A three-dimensional solution to measurement of the resultant reaction on the canopy by the strata activity and shield response required the elimination of several forces or moments that were thought to be nonparticipating or to not significantly affect overall shield mechanics. Required measurements for solution of the equilibrium equations were leg, canopy capsule, and lemniscate link forces. Two-dimensional analysis, which considered forces acting only in the roof-to-floor and face-to-waste plane, was also provided by reduction of the three-dimensional equations~

Jan 1, 1987

By Charles Vaught, Warren G. Lacefield, Ronald D. Wasielewski, Philip K. Berger, Henry P. Cole, John V. Haley, Shannon L. Price

A comprehensive review of published research was carried out to identify methods for teaching and assessing critical but nonroutine skills needed for coping with emergency situations. Computerized searches of the relevant data bases were carried out, along with identification of relevant articles and materials by personal contact with experts in many fields. The citations listed in this bibliography resulted from this systematic literature search and review. The computer searches and an analysis of this literature are described in technical report 1. Specific methods for assessing critical skills proficiency in aviation, medicine, organization management, the military, and other industrial/ technical workplaces were described. The potential application of these methods for teaching and assessing (1) critical first aid and (2) self-rescue and escape skills to underground coal miners in annual refresher training was explored. Research and development activities that may improve mine health and safety training were suggested. Most of the entries in this bibliography were assembled in 1984 through 1985. Study of these materials contributed to the completion of the project research that followed. This later work is reported in the project technical report 2 and the final report. This bibliography is most useful when combined with examination of technical reports 1 and 2 and the final project report.

Jan 7, 1988

By G. St. J. Perrott, G. W. Jones

"In cooperation with The Edison Electric Illuminating Co. of Boston, Mass., a survey was conducted in 1929 and 1930 by the United States Bureau of Mines to determine the general hazards of combustible gases and vapors in manholes and other underground openings owned by this company. The territory served approximates 650 square miles and includes 46 cities and towns. The transmission and distribution systems are on overhead construction and underground wires and cables run in underground conduits and manholes. There are 17,000 manholes on the system, and also an area in Boston proper served by the Edison tube system. These conduits and manholes are laid in various types of streets from the most modern type of cement roadbed to the older type of loose macadam. The conditions as found could be considered as typical of any public utility in the electric-light and power field. The survey extended over a period of about a year beginning in June, 1929, and ending in July, 1930, and during this time 1,765 different manholes were tested and a total of 4,068 tests were made.Previous to starting the actual survey, one of the writers, G. W. Jones, spent considerable time in Boston determining the best methods of practical· test procedure. In this work cooperation was given by John Campbell, superintendent, special service department, who for a number of years has been making a study of explosions in underground street areas and preventive measures in Boston and various cities.After this preliminary investigation the tests were continued by employees of the Edisun Company. Copies of all records of tests were forwarded to the United States Bureau of Mines Pittsburgh Experiment Station so that the writers were in close touch with the progress of the survey, and changes could be made in the test procedure whenever deemed necessary."

May 1, 1931

By E. J. Kloos, R. H. Schutz, B. I. Ferber

To protective devices, the Bureau of Mines has established five schedules of minimum performance requirements for the approval of respirators. The current revisions of these schedules include 13D for self-contained breathing apparatus, 14F for gas masks, 19B and the amendments to 19B for supplied- air respirators, 21B for dust, fume, and mist respirators, and 23B for chemical cartridge respirators. Copies of these schedules may be obtained from the Bureau of Mines, Publications Distribution Section, 4800 Forbes Avenue, Pitts- burgh, Pa., 15213. Approval tests on respirators are performed only at the request of the manufacturer of the respirator and at his expense. If the device meets the approval requirements, a certificate of approval is granted on the complete respirator. This certificate states that as long as the respirator is manufactured as originally approved, or in accordance with any changes covered by an exten- sion of the original approval, the manufacturer may advertise and sell his respirator as being approved by the Bureau of Mines. Many industries and regulatory agencies require that respirators approved by the Bureau of Mines be used where respiratory protection is needed. The Bureau of Mines, how- ever, has no regulatory power over the use of the respirators that it approves. It acts as an impartial testing agency to insure the availability of suitable and safe respirators. At frequent intervals, the Bureau of Mines purchases approved respirators and replacement parts on the open market. These are examined for conformity to the approved status, and are checked to insure that the manufacturer's pro- duction facilities are maintaining a satisfactory quality control.

Oct 1, 1965

By Charles A. Seitz

This Bureau of Mines report describes a chromatographic method for analyzing impurities in helium that utilizes a helium carrier gas contain-ing 25 to 30 ppm Ne. An example of the effect of trace amounts of nitrogen, methane, and moisture on the detector's response is shown. The added neon in the carrier does away with irregularities of the analysis which were experienced when the carrier contained up to 3 ppm Ne. The addition of 25 to 30 ppm Ne causes a loss of sensitivity, but the re-maining sensitivity is adequate for routine analyses. The high-neon carrier allows positive and more linear responses for eight impurities: neon, hydrogen, argon, oxygen, nitrogen, methane, carbon dioxide, and ethane. Neon concentration levels of 0.02 to 125 ppm in helium carrier gases were studied. The high-neon carrier has been in successful rou-tine use in Bureau of Mines helium facilities since October 1981.

Jan 1, 1985

By Robert Bottge

When a company develops a mineral property in a remote area of Alaska, it must consider how best to house its personnel. This Bureau of Mines report examines the economics of two options: company towns and company camps. The price required to maintain a 15% discounted-cash-flow rate of return (DCFROR) was derived for hypothetical 1,000-st/d cut-and-fill mines and 50,000-st/d open-pit mines located in three different regions of the State, One set of hypothetical mines utilizes a townsite; the other utilizes a relatively new concept, a fly-in camp or commuting operation, in which two shifts of employees operate the mine and all associated facilities for 1 week before being replaced by a second crew. The study shows that operating costs were higher for mines employing the commuting option than for mines having a company town because of the additional wages paid for overtime hours; however, the price required to obtain a 15% DCFROR for the single-product copper concentrate, f.0.b. the mill site, was significantly lower owing to the lower investment costs for the camp-type operation. The economic advantage for those mines utilizing the camp increases from south to north and from the coast toward the interior.

Jan 1, 1986