Search Documents

By Albert J. Rambosek

The results obtained in a study of the stress conditions existing in a drill bit-point area and in the underlying rock, when the bit was in full but nonpenetrative contact with the rock, are presented. This investigation by the Bureau of Mines was the preliminary exploratory phase of a long-range program of research on rock drilling to establish criteria for the maximum economically feasible rate of rock penetration. The photoelastic technique of experimental stress analysis was the principal method used to obtain the data. Transparent models and transmitted light were employed to investigate patterns in drill-bit models and isotropic materials under the bit when subjected to a concentrated static load. Comparative stress data for anisotropic rock were obtained by the reflective photoelastic technique. Brittle lacquer and an extensometer were used obtain supplementary information wherever substantiating data were desired to check photoelastic results. The zone of maximum shear occurs along an arc near the contact face of the bit. The stress distribution pattern in an isotropic model rock near the area contacted by the bit was nearly a mirror image of that exhibited within a similar areal zone of the bit. The stress pattern in granodiorite specimens was similar, though not symmetric, to the pattern in the isotropic model rock. The asymmetry of the stress pattern in the granodiorite was attributed to the anisotropic characteristics of the constituent minerals of various sizes.

Jan 1, 1963

By D. Hinton, M. McCawley, R. C. Lantz, F. Pisano, C. Stanley

"INTRODUCTION Aerosols (5 um have not been shown to be consistently generated and characterized in inhalation chambers. Particle deposition in the lungs however may occur with particles as large as 25 um(1). Therefore, in order to closely simulate the atmosphere of an underground coal mine where the distribution is bimodal, with modes at S and 15 um (2), particles much greater than <1 um must be characterized for uniform mixing and size distribution within these chambers. The Hazelton Animal Exposure Chamber has been chosen because it has been best characterized for smaller particles (<1 um) (3), and is the major type used by most inhalation toxicology institutes such as Lovelace Inhalation Toxicology Institute and Battelle Northwest Laboratory.BACKGROUNDPreviously published studies on the inhalation of solid aerosols have attempted to characterize the distrition of particles of <2 um in diameter. There are no published reports of extensive work characterizing either the size distribution of particles <1 um or the concentration throughout the exposure chamber (Table 1).Table 1 shows the variability and sizes of several aerosols <1 um in diameter used in five previous chamber studies.Discussion of Previous StudiesThe study done by Bauermash, Bryan, Dickinson, and Burke (4)stated two major concerns in the development of the 6.5 ft. diameter chamber. The first was that a quantity of animals could be exposed to the same concentration regardless of the location of the animal, and second was that the chamber could be easily cleaned and decontaminated. The solution to the first concern required a circular chamber with the contamination air entering the chamber somewhere along the central axis. The animals could then be changed during exposure time so that each animal was exposed throughout the total volume."

Jun 1, 1988

By Arcy R., D&apos George

The Bureau of Mines has developed, on a laboratory scale, a superior Eluex-type circuit for eluting and recovering uranium from ion exchange resins. The improved circuit differs from conventional Eluex practice in that a stage of uranium solvent extraction is coupled with each stage of resin elution rather than the elution and solvent extraction operations being conducted separately. The new system reduces the number of stages, retention time, and resin inventory in the elution circuit to one-fourth or one-fifth that in existing circuits. The system is applicable to both resin-in-pulp and moving-bed-type ion exchange uranium recovery circuits.

Jan 1, 1969

By Thomas J. Peters

In 1987, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied a 12,564-acre portion of the 34,795-acre Rockhouse Wilderness Study Area (CA-010-029) in order to evaluate its identified mineral resources. The study area is located in Kern and Tulare Counties, CA, about 60 air mi northeast of Bakersfield at the south end of the Sierra Nevada. A review of the geologic and mining literature, and a field examination identified a turquoise and a gold prospect in the study area, and another gold prospect and a feldspar prospect within a mile of the study area boundary. Thirty-three rock and 16 alluvial samples were taken.

Jan 1, 1988

By Ronald A. Vary

This paper is one of a series prepared by the United States Bureau of Mines dealing with milling methods and costs. In view of the current revival of interest in gold mining, information dealing with practices and costs in the development of gold properties is apropos. Milling practice at a small gold property in the prospect stage is described where, with a small outlay for plant and equipment, development has been carried on for about 20 months on the proceeds of the mill operation with little additional expenditure. The paper shows about what may be expected as to costs at a small property operated under northern climatic conditions and with rigid economy throughout the plant.

Jan 1, 1931

By Albert W. Deurbrouck

Twelve samples from six Barbour County coal beds were analyzed for this report. The samples collected were generally high sulfur content coals, frequently exceeding 3 percent in the raw-coal sample. Many of them could not be upgraded to acceptable metallurgical standards even by rigorous preparation procedures. The production of coal in the county in 1963 amounted to almost 3 million tons of which 44 percent was mechanically cleaned.

Jan 1, 1965

By William A. Beck

This paper is one of a series, describing current practice in diamond drilling for production at various mines throughout the United States. It describes the drilling and blasting methods, used at the Tennessee Copper Co., which started using deep-hole drilling for blasting in 1927, employing inde- pendent, rotation percussion drills with sectional drill steel. Since 1942 the company has employed diamond drills for deep-hole drilling. This method has now passed the experimental stage and promises to become permanent. The elimination of rock dust and safer working conditions for the drill crews are listed as the main advantages. The higher initial cost of equip- ment is the principal disadvantage.

May 1, 1948

By G. W. Elger

The Bureau of Mines conducted laboratory and larger scale studies on samples of domestic perovskite and ilmenite ore concentrates to devise a procedure for recovering TiC from these ores. From the concentrates, mixtures of titanium and calcium carbides were produced. The carbides were then ground and reacted with water. This reaction decomposed the CaC2 to acetylene and hydrated lime and simultaneously liberated the TiC. Using a combination of elutriation and gravity-separation techniques to separate the hydrated lime, approximately 93 pct of the titanium was subsequently recovered as purified carbide containing 54 to 70 pct titanium with CaO content as low as 0,6 pct. This combination of techniques can be used to separate more than 90 pct of the CaO from the TiC. Therefore, this carbiding procedure is a viable method for treating titaniferous materials, including perovskite, that contain more than 20 pct CaO. Tests made in a static-bed reactor showed that for the reaction of TiC with elemental chlorine to produce titanium tetrachloride (TiCI4), a temperature of at least 940° F is desirable to achieve a suitable extraction of titanium in a laboratory chlorination reactor. In fluidized-bed tests at 840° F, 98 pct of the titanium contained in TiC was extracted.

Jan 1, 1980

By E. G. King

THIRD-LAW entropy data for zirconium-containing compounds are sparse. Kelley a lists entropies at 298° K. for the oxide, tetrachloride, nitride, and silicate, as well as for the metal. The present paper presents heat capacities between 51° and 298° K. and entropies at 298.15° K. for the zirconates of the alkaline-earth metals-calcium, strontium, and barium. The authors believe magnesium zirconate does not exist as a stable compound at room temperature. Entropies of formation from the constituent oxides also are given. MATERIALS The materials used in this investigation were synthesized and analyzed in the Berkeley Laboratory of the Bureau of Mines. Calcium zirconate was prepared by heating an intimate mixture of reagent-grade calcium carbonate and pure zirconia for 30 hours between 1,200° and 1,300° C. and for 32 hours between 1,400° and 1,500° C. As part of the heating schedule, the sample was ground and mixed seven times. Periodic analyses and minor adjustments of composition were made. Analysis of the final product gave 31.19 percent calcium oxide (theoretically 31.28 percent) and 68.67 percent zirconia (theoretically 68.72 percent). The X-ray diffraction pattern agreed with that in the ASTM catalog.

Jan 1, 1960

On December 16, the General Services Administration (GSA) suspended weekly sales of surplus silver from the national defense stockpile because Congress approved the Defense Appropriation Act, which contained an amendment to halt silver sales. The amendment, introduced by Senator James A. McClure (R., Idaho), prohibits sales for 6 months while the impact of the sales and alternative methods of disposal are evaluated. The GSA sold 2 million troy ounces since sales started October 14. 46.5 million troy ounces were authorized to be sold during this fiscal year and an additional 58.6 million troy ounces were authorized to be sold over the following two fiscal years. The stockpile held 139.5 million troy ounces of silver when sales began in October. Brush Wellman, Inc., a vertically integrated producer of beryllium products announced plans to modify its Delta, Utah beryllium concentrate processing facility to utilize beryllium concentrates containing as little as 7% beryllium oxide. The company plans to invest $2.5 million for this modification with completion expected in mid-1983. Implementation of this plan to consume lower grade beryllium minerals will significantly increase world reserves of beryllium concentrates.

Jan 1, 1981

By Ralph B. Adair

The Bureau of Mines conducted laboratory and continuous pilot plant flotation tests to determine the feasibility of recovering commercial-grade mica from an Alabama graphitic-mica schist. Preconcentration of the ground ore on a Humphrey&apos;s spiral was employed to reject the heavy minerals and part of the quartz in a product virtually free of mica. The acid-cationic mica flotation process recovered over 89 percent of the mica in a product containing 98.7 percent mica. Grinding of the mica concentrate in a fluid energy mill produced a product with a bulk density of 12 lb per cubic foot.

Jan 1, 1969

By R. Havens

During the course of the investigation of possible domestic sources of manganese, engineers of the Bureau of Mines examined and sampled two manganese mineral deposits in northeastern Utah. The Daggett Chief claims are situated in the northern part of Daggett County,5 miles southwest of Manila, Utah, and approximately 57 miles from Green-River, Wyo. Owners of the property are J.E. Harris Of Salt Lake City, Utah, Nels Palleson of Manila, Utah, and J. P. Larson. The manganese occurs in a vein 6 to 8 feet wide in a shale and sandstone formation. Two distinct occurrences Of manganese are present Within the vein, and samples of each were subjected to testing. Lot A, representing .probably the major portion of the Manganese; was composed of nodules and veinlets of manganese oxides in a semicompact; gray, shaly formation. Lot B represented a 15-inch vein of dense iron-manganese ore. .Most of the laboratory work at Salt Lake City, Utah, was done on these two samples; but preliminary testing also was carried out on a small sample, physically similar to lot A, submitted by the owners.

Jan 1, 1949

By Gene Asai

The Bureau of Mines investigated the caustic extraction of alumina and soda from retorted dawsonite-bearing oil shale, as part of a program to devise technology for treating alternative domestic sources of alumina for the production of aluminum metal. Colorado oil shale yielding 13 pct oil (35 gal/ton) and containing 12 wt-pct dawsonite (representing about 4 pct extractable alumina) was retorted to obtain oil-free (spent) shale Spent shale was leached with dilute NaOH to determine the effect of particle size, retorting temperature, leaching variables, and storage conditions on extraction of alumina and soda and dissolution of impurities. Maximum alumina and soda extractions were obtained by promptly leaching minus 28-mesh spent shale, obtained by retorting raw shale at about 5000 C, with 0.5N NaOH. Under these conditions, dissolution of impurities such as Ca, Fe, Ti, and P was low. Leaching tests were made on spent shale stored for periods of up to 30 days at 0° to 42° C and at 0 to 100 pct relative humidity (RH). These tests indicated that significant reductions in alumina extraction would occur if spent shale were stored in ambient Colorado air under naturally fluctuating temperature and humidity.

Jan 1, 1983

By Robert H. Merrill

This Bureau of Mines report summarizes the design and tests of a gage that will simultaneously measure the deformation of a borehole along three diameters 60 degrees apart; the measurements are in a single plane normal to the axis of the borehole. The inherent errors in measurement are considered together with the problems associated with the use of the gage in the relatively severe environments in and around mine openings. These problems were treated in the design and tests of the gage and the results establish that the gage can be used to satisfactorily is determine estimates of the stresses in rock.

Jan 1, 1967

By B. J. Dalton

The Helium Research Center, Helium Activity, Bureau of Mines, is presently engaged in a critical examination of all of the PVT data on helium that appear in the literature. The long-range objective is the development of a single equation of state for helium that will allow all of the thermodynamic properties to be calculated and will reproduce all of the data within the accuracy with which the data are known. A preliminary objective is to obtain the best values of the second virial coefficients and to develop an equation that will reproduce the best values as a function of temperature. The method of treatment consists in expressing the PV product of a gas, for a given isotherm, in terms of a power series in either the pressure or the density and evaluating the constants by least squares solution. Associated with these functions whose coefficients have been evaluated by least squares, the following errors, or deviations, are of interest; the standard error of a single measurement; the standard error in each coefficient; and the standard error of the resulting function.

Jan 1, 1964

By B. J. Dalton

The Helium Research Center, Helium Activity, Bureau of Mines, is presently engaged in a critical examination of all of the PVT data on helium that appear in the literature. The long-range objective is the development of a single equation of state for helium that will allow all of the thermodynamic properties to be calculated and will reproduce all of the data within the accuracy with which the data arc known. A preliminary objective is to obtain the best val¬ues of the second virial coefficients and to develop an equation that will reproduce the best values as a function of temperature. The method of treatment consists in expressing the PV product of a gas, for a given isotherm, in terms of a power series in either the pressure or the density and evaluating the constants by least squares solution. Associated with these functions whose coefficients have been evaluated by least squares, the following errors, or deviations, are of interest; the standard error of a single measurement; the standard error in each coefficient; and the standard error of the resulting function.

Jan 1, 1964

By R. V. Ramani, J. Qin

"During the mining process, the insitu material is broken into different size ranges, from very, large pieces to very fine particles. Some of the fine particles become airborne. In underground coal mining, airborne respirable. dust is associated with health and safety of the miners: The amount and size distributions of airborne dust are important parameters to effective dust control measures. The design of underground mine experiments, including sampling procedures and sample analyses methods to determine these parameters are presented in this paper.. A total of fifteen continuous miner cuts were sampled. The amount of dust generated during the cutting process and the relationship between total and respirable airborne dust concentrations and amounts are examined.The amount of respirable dust airborne is on the average only. 0.016% of the respirable dust generated. On the average, 61% of the total .airborne dust measured is in the respirable size range. The amount of respirable airborne' is on the average 36% of the respirable size fraction in the total airborne dust. For equal proportion of rock and coal material cut, rock contributes about twice as much fines (<0.22 mm) as coal. Additional fundamental research is necessary to further the understanding of 'the airborne propensity of respirable dusts in mine atmospheres.INTRODUCTIONMining is a sequential process of breaking, gathering, loading, and transporting the in-situ .materials.' In underground coal mines, duet in both the non-respirable and respirable size ranges is generated and entrained in every phase of the process. Even though large amounts of dust particles' adhere to run-of-mine coals, part of the dust generated becomes airborne (Cheng and Zukovich, 1973). Studies have shown that bit type affects the amount of dust generated'(Evans and Pomeroy, 1966; Kurth et al., 1975; Roepke et al., 1976; Stecklein et al., 1982; and Khair and 'Reddy, 1986). Deep cutting can reduce airborne dust generation (Black and Schmidt, 1977 arid, Black et 1978). Mechanical properties of. coal seams are also important factors in dust generation. Laboratory studies have shown that Hardgrove Grindability Index (HGI) of the coal has a relationship with the amount of respirable. dust generated (Beafi and Ramani, 1979; Moore and Bise, 1984; and Moore, 1986). However, these relationships have not yet been validated with' data from the mines. The amount of dust airborne depends on a number of factors. Suppression of the airborne propensity of dust by water sprays is'widely practiced and is very effective. Water flow rate; pressure and configuration of water sprays have been identified as major factors affecting dust capture by sprays (Courtney and Cheng, 1977; Courtney et al., 1978; and Kissell et al., 1979). Ventilation is a very important means of controlling the dust level at the coal face (Jayaraman, 1977). According to a National Academy of Sciences study (1980), the mechanism of dust generation and the process by which the generated dust becomes airborne are complex and not yet completely understood coal seams are also important factors in dust generation. Laboratory studies have shown that Hardgrove Grindability Index (HGI) of the coal has a relationship with the amount of respirable dust generated (Beafi and Ramani, 1979; Moore and Bise, 1984; and Moore, 1986). However, these relationships have not yet been validated with data from the mines. The amount of dust airborne depends on a number of factors. Suppression of the airborne propensity of dust by water sprays is widely practiced and is very effective. Water flow rate; pressure and configuration of water sprays have been identified as major factors affecting dust capture by sprays (Courtney and Cheng, 1977; Courtney et al., 1978; and Kissell et al., 1979). Ventilation is a very important means of controlling the dust level at the coal face (Jayaraman, 1977). According to a National Academy of Sciences study (1980), the mechanism"

Jan 1, 1989

By Rogers F. Davis

This publication has been prepared to supply manufacturers and industrial users a listing of mobile diesel-powered equipment and subassemblies approved and certified by the Bureau of Mines for use in noncoal mines. Testing of diesel-powered equipment is one phase of the Bureau&apos;s program of health and safety that concerns approval of electrical and diesel equipment designed to prevent explosions, fires, shocks, or toxic hazards in underground mines, when such equipment is used and maintained properly. Manufacturers submit machinery and component parts to the Bureau for study of their design, safety features, and use. Equipment must pass exacting tests and must meet strict requirements established through research and experience and listed in the Bureau&apos;s permissible schedules before the Bureau approves it as permissible for safe use in mines.

Jan 1, 1963

By K. O. Bennington

The thermodynamic properties of aegirine, of composition [(Na0.869Fe30+7362 Fe20+16Mn0.03Ca0.1121)(A10.141Sil 9738)(06)], were experimentally determined at the Bureau of Mines as part of its efforts to advance minerals technology. The standard enthalpy of formation determined by hydrofluoric acid solution calorimetry is AHf298 = -641.12±0.73 kcal/mol. The standard enthalpy of formation from the oxides is AH298 = -37.136±0.509 kcal/mol. Low-temperature heat capacities were determined by adiabatic calorimetry from 19.1 to 304.6 K. The derived standard entropy is S298 = 38.03±0.14 cal/mol?K. The heat capacity was measured over the range 348 to 1,198 K by differential scanning calorimetry. These experimentally determined data were combined with data from the litera¬ture to calculate the Gibbs energies of formation and equilibrium constants of form¬ation over the temperature range of the measurements. Standard enthalpies of forma¬tion are given as functions of temperature. The standard Gibbs energy of formation at 298.15 K is AGf298 = -600.36 kcal/mol.

Jan 1, 1984

By M. R. Geer

American and European practices in cleaning fine coal are strikingly different. The tables, launders, classifiers, and pneumatic devices used in America are seldom employed in Continental Europe, where much of the fine coal is cleaned in feldspar jigs, often supplemented by froth flotation of the extreme fines. This difference in choice of cleaning equipment may be fortuitous, but in large measure can be attributed to a difference in economic factors. Coal being more costly in Europe, there is greater emphasis on efficient cleaning of all sizes, including the extreme fines, and it is common to produce a high-ash middling for "on-site" consumption to avoid any waste of fuel value. The feldspar jig has been found advantageous under these conditions. In the United States fuel coal must be prepared as cheaply as possible, and metallurgical coal must be prepared as efficiently as possible; thus in both branches of preparation practice, any cleaning device that promises greater economy or higher efficiency warrants consideration. The feldspar jig, as employed in Europe, has a much higher unit capacity than the wet table used so extensively here and therefore offers economy in the capital costs of a washery through saving in space. As pointed out by Vissac,4/ the jig operates under automatic control, and therefore can cope with fluctuations in quality of feed. Maintenance costs for a single, large-capacity unit, such as the feldspar jig, would be expected to be lower than those for a battery of low-capacity cleaners. These considerations led the Bureau of Mines to undertake an investigation of the feldspar jig to determine its possible usefulness in this country.

Jan 1, 1958