Search Documents

By Theron A. Klinefelter, Sidney Speil, Sidney Gottlied

"INTRODUCTION The investigation of domestic talcs by the United States Department of the Interior Bureau of Mines, was initiated in December 1941 at the request Gen. Charles Hines of the United States Army. The urgency for such study was expressed by General Hines as follows:The radio-manufacturing industry has recently been expanded by the Army to provide sufficient, capacity for defense needs, and considerable concern has been expressed by the supply Arms and Services over maintaining continued availability of supplies of the necessary raw material. These ceramic products are used by the Signal Cores in all Army radio equipment, and to a greater degree in the new special ultra-high-frequency equipment. The Air Corps has recently become a user large amounts of radio-grade ceramics for aircraft spark-plug covers required for high-altitude operations. In addition, the use of this material is essential to the proper functioning of the radio-navigation aids of the Civil Aeronautics Board.Progress in the Bureau of Mines studies on talc was made available to representatives of the Army and Navy through frequent interim reports. Through the efforts of the several war agencies concerned with raw-materials supply and the domestic talc producers, the condition of scarcity that developed in 1942 passed to one of ease in 1943, and has so continued to date. Tentative estimate of reserves delineated indicates a supply of high-grade steatite sufficient to meet military war requirements for at least 4 or 5 years."

Apr 1, 1945

8186. Aquilina, C. Determinazioni relative di gravita eseguite nel 1939 (Relative Determinations of Gravity Made in 1939), Ric. Ingegn, Rome, vol. 10, 1942, pp, 6376. In 1939, the author made a survey of relative gravity in the Mediterranean-basin, 41° 35,5' to 41° 56.3' northern latitude and 0° 10,3' to 0° 28' longitude, referred to Mt. Mario. Ten stations were covered; 25 other stations had been occupied in the vicinity of Rome and in Albanian mountains during previous years. The new measurements revealed gravity anomalies ranging within the following limits: (1) With a free-air reduction, between + 29 and + 120 mgl., average + 60 mgl.; and (2) with a Bouguer reduction, between + 22 and + 87 mgl., average + 41.5 mgl. - V. S.

Jan 1, 1946

By J. Bruce Clemmer

In the experimental concentration of Vermont talc-magnesite ores, talc concentrates and tailings rich in magnesite were obtained. On account of the possible market value of the magnesite, the tailings are given consideration' in this report along with the talc. After some comments about the talc industry, the magnesite that accrued as tailings will be considered. Then the flotation results will follow.

Jan 1, 1936

By Michael G. Zabetakis

Limits of flammability of normal propyl nitrate (NPN) vapor were investigated at ambient and elevated temperatures. Minimum spontaneous ignition and decomposition temperatures were determined with laboratory apparatus over the pressure range from 0 to 4,000 p.s.i.g. Flame speeds and the detonation susceptibility of NPN vapor were measured at elevated temperatures. Stable detonation was obtained with liquid NPN at elevated temperatures, and the detonation velocity was determined to be between 4,700 and 5,100 m./sec.

Jan 1, 1962

By J. E. Rourke, O&apos

A wide variety of techniques and equipment are available for coring soft or poorly consolidated geological material. This report presents a comprehensive literature review and evaluation of these techniques and equipment. A potential user will find guidelines in this report to assist him in selecting sampling equipment. A bar chart shows what samplers have been used under what geological conditions, and gives the specific literature references. Two matrices rate the present techniques and equipment with respect to reported success for sampling specific materials, and with respect to several performance characteristics including complexity of use and core quality. These matrices are supplemented with tables of typical sampling equipment. and program costs. Near-term future developments are seen primarily in improved training of drillers, and in instrumenting the drilling operation to provide objective data on drilling characteristics. An extensive annotated bibliography, a catalogue of equipment suppliers including specifications and cost ranges, and a list of manufacturers and distributors are appended to the report.

Jan 1, 1978

By Chris Jobes, Alan Mayton, N. Kumar Kittusamy, Dean Ambrose

NIOSH researchers conducted a study to compare seat designs on underground coal mine haulage vehicles. The objective of the study was to support prior findings that NIOSH-designed seats, which incorporated ergonomic design features (e.g., viscoelastic foam padding and low-back support), are improved designs. Based on measured levels of vehicle jarring/jolting and perceived discomfort, researchers evaluated four different designs - two in-use and two NIOSH-developed, ergonomic designs. Researchers collected data using a short questionnaire, a linear, visual analog scale, and accelerometers with a data recorder. Results showed that vehicle operators favored the NIOSH seats with added adjustability, low-back support, and improved seat padding over the existing seats. In addition, the measurements indicated all NIOSH seats performed better than the existing seat, under the no-load (worse of two) conditions, in reducing peak acceleration, crest factor, and RMS acceleration. The authors summarize the data collected and operator preferences for seat designs and different foam padding arrangements.

This report summarizes the results of the Narragansett Win Projec't's activities during the U.S. Bureau of Mines (BOM) Phase 1, which was transitional from and which followed the National Science Foundation (NSF) Phase which initiated the investigation of New England's potential roil resource. The 960 sq. mile basin is structural and topographic lowland containing 12,000 to 20,000 ft. of terrigenous clastic sediments of late Pennsylvanian age, and which rests on an upper Precambrian and Cambrian basement. The Rhode Island Formation, which is the coal-bearing unit, comprising the bulk of the Pennsylvanian rocks consists, in order of decreasing abundance, of sandstone, conglomerate, silts tone, shale, and coal. In the NSF Phase, 24 drill-holes yielded 17,900 ft, of core; in the BOM Phase I study, 4 drillholes yielded 2,100 ft. of core. Anthracite and semi-anthracite was encountered in beds Up to 30 ft. thick in widely spaced parts of the Basin. The coal, typically very low in sulfur, and a high ash anthracite, won mined in substantial volumes from 1808 to 1959 from shaft and open lit in Portsmouth and Cranston, R.I., and in lesser volumes in Mansfield, Mass. Currently coal is now being mined in Plainville, Mass. as a fuel in the manufacturing of light-weight aggregate from the same quarry that serves as the source of the rock being processed. The structurally complex Narragansett Basin is now known to have a greater extent than earlier since recent drilling by others (Chapter 2) has confirmed our interpretation that the Basin extended offshore south A Boston. The, Basin also extends into Rhode Island Sound to the south. The geological structure is more complex in the southern part of the Basin than in the northern part. Three episodes of folding have been documented on Aquidneck Island and four episodes of faulting have been demonstrated for the Basin as a whole. Relatively less well exposed rock in the northern part of the Basin, increases the difficulty of recognizing and correlating structural episodes in the northern part of the Basin. The Basin his hewn subdivided into six structural domains which appear to have distinctive structural, metamorphic, paleontological and sedimentological differences that mw assist in isolating important events in the evolution of the Basin and its component parts. The tentative structural model recently developed in POP Phase I has important implications for exploration and mining. In the first and second folding stages the coal is mobilized and thickened in the crests and troughs of folds whose axes are horizontal to subhorizontal. While conventional coal exploration and mining methods are not applicable, great thickening in the crests and troughs of large scale structures, which can he defined by geology, geophysics and drilling, may provide compensating advantages. Bedrock over most of the Basin is 0-50 ft., but thicknesses of glacial deposits up to 150 ft. are present locally. Pro-Pleistocene topographic trends are controlled by structure and rock hardness; Pleistocene deposits aligned to the S. F. are superimposed on earlier trends. The southern part of the Basin is mainly dominated by high grade Barrovian metamorphism and plutonism of Permian age, related to the Alleghanian Orogeny. About 300 sq. miles of the 960 sq. mile Basin has been affected. The remaining 660 sq. miles, in the chlorite and subchlorite zones of metamorphism are compatible with the presence of high quality anthracite and semi-anthracite. Illite crystallinity studies begun in the NSF Phase, have been carried out in the BOM Phase l with important results. About ME of the northern Basin is now known to be in the diagenetic (unmetamorphosed) or subchlorite zone and the remainder in the chlorite zone of metamorphism. Mite studies, probably best recording temperature effects, show a generally progressive increase from the NW corner of the Basin near Plainville, Mass. toward the south and southeast. Reflectivity and coal petrography studies, probably best recording pressure and effects related to shearing, indicate a generally opposite pattern. Thus these methods provide powerful tools for the ultimate solution of problems important to coal exploration for coals of higher combustible volatile content and exploitation of these. Due to the complex nature of the coal, chemical data may not he easily used to determine rank. The coals have been tectonically deformed and mineralized. This deformation plus thermal metamorphism have altered the coals, in some cases by producing natural coke. Brecciated coal is often coated with a secondary depositional carbon. The coals' hydroscopic nature and high ash contents are due to the deformed nature of the coal and the presence of this secondary carbon. The stratigraphy and sedimentology of the coal-bearing Rhode Island Formation is similar to described alluvial fan deposits. The non-geological studies al-low three conclusions to be made: 1. A substantial number of areas have been identified in the Narragansett Basin in which mining could be carried out without undue difficulty from a land use point of view. 2. Substantially more than two hundred instances of past or current- mining activities have been identified in the Basin. Many of those are in areas defined as geologically interesting, and may be advantageous From the point of view of future exploration. 3. The map synthesis technique developed for this contract is successful and may easily be adapted to future exploration in its current form and also in its expandable form dealing with unit measurements of one-tenth mile. We recommend that BOM Phase 2 exploration should accomplish the intent of the Congressional language in House Report No. 95-1251, to continue a substantial drilling and geophysics program: "The Committee expects the Bureau to continue studies involved in ascertaining the extent and quality of low sulfur coal reserves in the Narragansett Basin in New England including necessary drilling and geophysical studies. The knowledge of the extent of such deposits is of great importance to this 'energy pour' area".

Jan 1, 1979

By H. A. Doerner

"The pure mineral chromite, FeO.Cr203, consists of ferrous and chromic oxides, chemically united in equal molecular proportions. Unfortunately, pure chromite as defined above appears to be a rare exception. In most chrome ores the mineral may be considered a combination of spinel, MgO.Al203, and chromite, with the latter predominating. The ratios between the four common constituents Fe0, Mg0, Cr203 and A203 vary greatly, and other minor constituents such as TiO2 and. Fe203 may also be present.In the mechanical concentration of chromite ores the maximum grade of concentrates that can be produced is thus limited by the composition of the chrome minerals present. Pure chromite contains 68 per cent Cr203, but the Cr203 content of the chrome minerals in commercial ores varies between 45 and 60 per cent and the average is not far from 55 per cent.Chromite is usually associated with serpentine. Other silicates, quartz, dolomite, magnetite, ilmenite and other iron Minerals are frequently present.The amenability of a chrome ore to concentration, depends upon the kind and amount of the various gangue minerals present and the amount .of crushing necessary to separate the chromite from them.A relatively small amount of chrome ore is concentrated by milling. In most cases the mine product is simply hand-sorted. Such chrome deposits as are known in the United. States can not be worked in this way on account of one or both of the following conditions: High cost of labor and finely disseminated impurities. There are, however, several deposits in the United States, Canada, and Alaska which may be able to compete with imported or by efficiently utilizing modern ore-dressing and milling methods."

Nov 1, 1930

By Russell Griffin

The current state of the art of fire and smoke detection technology is reviewed from the standpoint of suitability for use in under- ground metal and nonmetal mines. Detection modes, fire signatures, and environmental considerations are included. Preliminary results of long- term, in-mine tests are presented.

By J. R. Ross

Recovery of uranium from slightly alkaline mine water, available in the Ambrosia Lake district of New Mexico, was studied using countercurrent ion exchange columns developed by the Bureau of Mines. Approximately 5 million gallons of mine water containing 9 to 12 ppm U308 was treated by ion exchange using a 14-inch-diameter absorption column composed of five or six compartments each 4 feet deep. Uranium recoveries averaged in excess of 98 percent at solution flows ranging from 15 to 25 gallons per square foot per minute and resin loadings up to 3.6 pounds of U.08 per cubic foot. In subsequent tests, loaded resin was continuously eluted in a countercurrent elution column with a diameter of 4 inches and containing a bed of resin 9 feet deep. The resin was eluted to a residual loading of less than 0.06 pound of U305 per cubic foot, at a resin-retention time of 224 minutes, using only 1.9 volumes of 1.1 M NaCl-0.05 M NaHCO3 solution per volume of resin. Compared with existing ion exchange practices for recovering uranium from mine waters in the Ambrosia Lake district of New Mexico, use of these improved ion exchange contactors would reduce ion exchange resin requirements at least 70 percent and allow further substantial reductions in capital and operating costs.

Jan 1, 1971

By R. B. Fisher

This report gives the results of mineralogical research on the Nicaro (Cuba) nickel ores and plant products. These studies were made under a cooperative agreement with the General Services Administration (GSA) of the U. S. Government. The purpose of the investigation was to obtain fundamental data that would be useful to other GSA contractors concerned with the Nicaro ores in their research on reduction roasting, leaching, and other phases of the project; and to the metallurgical staff of the Nicaro plant in Cuba. The overall objective of the combined research was to provide data to accomplish metallurgical improvement in the operations of the U.S. Government-owned plant at Nicaro, Oriente Province, Cuba. Particular emphasis is placed on improving the recovery of nickel from the ores and on the possibility of recovering other valuable constituents, especially cobalt. This study presents the physical and chemical characteristics, mineral associations, differential thermal analyses in controlled atmospheres, and X-ray studies of the ores and plant products. The nickel ores, serpentine and laterite, were from the Ramona-Lama Mulo and Ramona ore deposits. Serpentine ore consisted of serpentine-group minerals, basic iron oxide, magnetic iron oxides, chromite, olivine, enstatite, anthophyllite, cryptocrystalline quartz, wad, and a trace of calcite. This ore contained 1.6 percent nickel, 0.05 percent cobalt, 0.86 percent chromium, and 17.4 percent iron. Laterite are was composed principally of goethite with some altered serpentine, quartz, chromite, wad, magnetite, maghemite, and hematite. It carried 1.3 percent nickel, 0.11 percent cobalt, 1.9 percent chromium, and 48.4 percent iron.

Jan 1, 1959

By Bruce Pinkston

This report presents a description of the Prototype Demonstration Vehicle developed under U.S. Bureau of Mines Contract No. JO 366003, "Improving Man Transit Safety". This vehicle was constructed to assess the feasibility of a set of equipment related guidelines which were drafted in Phase I of the same contract. State-of-the-Art improvements were embodied in such areas as collision survivability, occupant comfort, and multiple mode (on and off rail) operation. The electric battery-powered vehicle carries a twelve man section crew at speeds up to 12 mph. The description of the demonstration vehicle is presented in Volume I. Safety Guidelines are presented in Volume II.

Jan 1, 1981

By Richard Mainiero, Donald A. Hurd, James H. Rowland

In previous conferences the authors have reported on toxic fumes generated by the detonation of ANFO. The research reported here extends the earlier work to include an emulsion blasting agent and ANFO/emulsion blends. Explosive mixtures were shot in 4-inch Schedule 80 steel pipe in a chamber in the experimental mine at the Pittsburgh Research Laboratory (PRL). Following each shot, the fumes in the chamber were analyzed using on-line instrumentation. A major goal of the research was to gain a better understanding of the factors that lead to the generation of toxic fumes in blasting operations. Earlier studies have suggested that the high nitrogen dioxide and nitric oxide concentrations in product clouds might be the result of the poor confinement provided by relatively weak ground strata or the exposure of the explosive to ground water prior to shooting the shot. Various mixtures of ANFO and emulsion were detonated in schedule 80 steel pipe and galvanized sheet metal pipe to evaluate the effect of confinement. Explosive mixtures were also allowed to soak in water for less than one day, one week, one month, and two months to determine which explosive mixtures would be degraded and observe what effect this degradation had on fume production. Results indicated that the production of nitrogen dioxide increased with low confinement of the detonating explosive and with exposure of the explosive to water.

By Warren E. Morrison

INCREASED production and utilization of minerals fuels and power accompanied the overall expansion in U.S. economic activity during 1963, which saw continued advances toward higher production, employment, and purchasing power. During 1963, record levels of wages, profits, and consumption were attained, while costs and prices maintained the stability exhibited throughout most of the recovery period. Expanding industrial production, the average index of which went from 118.3 in 1962 to 124.3 in 1963, narrowed the gap of unused manufacturing capacity to an estimated 5 percent. Gross national product (GNP), another major indicator of economic activity, reached a record level of $583.9 million (current dollars) during the year, this being $27.7 billion, or 4.9 percent above 1962. These achievements were somewhat marred by unemployment, which remained at 5.5 percent of the labor force in 1963, and the continued deficit in the U.S. balance of payments. Against this general background, total national consumption of energy resources for the year was equivalent to 49,816 trillion British thermal units (Btu), an increase of 4.2 percent over 1962. This represented a somewhat lower rate of growth than for GNP during the year.

Jan 1, 1964

By Wilson Blake

Rock preconditioning in advance of mining was shown to be an effective means of rock-burst control based on the results of a field demonstration carried out on the 7700 level of the Hecla Mining Company's Star mine. Mining through the preconditioned zone was characterized by greatly reduced rates of released seismic energy and no bumping or rock bursting occurred within the preconditioned zone. Mining above the preconditioned zone was characterized by greatly increased rates of released seismic energy and rock bursting, particularly where the vein became very narrow in waste zones. This increased incidence of rock bursting points out the need for stope preconditioning to be carried out on an entire stope block basis. The data obtained from the monitoring of the mining above the preconditioned zone on the 7700 level will be extremely useful in evaluating any future stope block preconditioning experiments on the lower levels or the Star mine.

Jan 1, 1980

By Gustav Wirth

"ABSTRACTIn exothermic and endothermic catalytic reactions, control of the temperature is of utmost importance. Basic calculations are developed for determining catalyst volumes of various types of reactors that give particular temperature distributions, and the individual designs are compared.INTRODUCTIONA narrow range of permissible operating temperatures characterizes many, catalytic reactions, and yields of the desired product are reduced sharply if operating temperatures fall outside of this optimum range. In order to achieve close temperature control, reactors with internal heat exchange have been developed in which thin layers of catalyst are located between cooling surfaces.The temperature distribution for an exothermic reaction in such a thin catalyst layer is shown in figure 1. Reactive gases flow downward through the catalyst section, which is 2so wide. It is assumed that a constant amount of heat is generated per unit of bulk catalyst volume, and that this heat is entirely removed through the walls. Consequently, except for a short section at the entrance of the reactor, the heat of reaction is not available for raising the temperature of the gases. Thus, at all points equidistant from the axis, the temperature is the same throughout the entire reactor. At the middle of the gas stream, the temperature is designated as uo. Traveling radially from this point, the temperature decreases because of the removal of heat through the walls and reaches, in the vicinity of the cooling surface, the value u1. Over a relatively narrow zone of width, b, the temperature falls to the value u2 at the cooling surface. Because inadequate data are available on heat-transfer coefficients for a gas flowing through a porous bed, and also because the narrow zone, b, is probably without effect on the reaction by virtue of its low temperature, the temperature drop in this zone at the cooling wall was disregarded. The following calculations were made on the basis of the temperature drop (u0 - u1) resulting from heat conduction within the main body of the catalyst bed only."

Nov 1, 1950

By D. H. Hileman

Economic investigations indicate that bituminous coal can be mined underground in the Uinta region and marketed at a cost competitive with that of other energy sources in the West. A selling price of $3.90 per ton of coal was calculated from a cost analysis of a projected coal mine in the Emery coal- field of Utah. Although mines in some of the coalfields have extremely difficult mining conditions and cannot compete in the energy market at this price level, at least two other coalfields in the Uinta region contain coal reserves that could be mined and sold at a price of approximately $3.90 per ton. Projections by power companies and other coal-consuming industries indicate a strong future market for the large coal reserves in the Uinta region.

Jan 1, 1970

By Dennis R. Dolinar, John L. Ellenberger, Gabriel S. Esterhuizen, Anthony T. Iannacchione

A survey of pillar conditions was carried out at 21 operating limestone mines that use the room-and-pillar method. The surveyed pillars were all located in rock that was classified as “Good” to “Very Good” using the RMR rock mass classification system. The average pillar width was 14.5m and the width to height ratio varied between 0.53 and 3.52. Pillar conditions were rated using a visual rating system that accounts for the effect of geological structures as well as stress related fracturing. Nine cases of pillar instability were recorded. Pillar instabilities were typically limited to individual pillars or small groups of pillars within an otherwise stable layout. Local geological structures such as inclined discontinuities or weak bedding planes contributed to instability in seven of nine cases that were observed. Elevated pillar stresses contributed to instability in the two remaining cases. All the unstable pillars observed had width-to-height ratios of less than 1.5. It is concluded that pillar instability is most likely to be caused by unfavorable geological structures in pillars with width to height ratios of less than 1.5. Stress related instability such as rib spalling becomes more prevalent when the average pillar stress approaches approximately 20 MPa.

By Thomas W. Camm

This study was done to evaluate the costs of various dumping operations at waste and spoil piles. It has been theorized that accidents associated with dumping operations might be reduced by short-dumping rather than edge-dumping, but many operators have been reluctant to use short-dumping because they believe it is not as cost effective as edge-dumping. To evaluate this perception, researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health reviewed the costs of various dumping methods at waste and spoil piles. The study found that overall cost differences between the two methods were not significant in most cases. However, while overall cost differences between the two methods appear small, capital costs could be more significant when short-dumping if numerous dump sites are used concurrently. The choice of which method to use should be based on considerations of the safety of dozer and truck operators.

Jan 1, 2000

By Arnold M. Lansche

DOMESTIC OUTPUT of white arsenic, As2O3, was derived entirely as a byproduct of smelting arsenic-containing copper ores by The Anaconda Company at Anaconda, Mont., and American Smelting and Refining Company at Tacoma, Wash. Arsenic metal was not produced. Consumption, and Uses.-Most of the white arsenic produced in 1964 was consumed in manufacturing lead and calcium arsenate insecticides. In the 12 year period since 1951 the production of lead arsenate insecticide has varied between 7,800 tons and 4,900 tons, indicating that lead arsenate has maintained its position in competition with organic insecticides.

Jan 1, 1965