Search Documents

By Jr. Gabler

Because of concern over the availability and reliability of an uninterrupted supply of manganese and other materials, the U.S. Congress requested that the U.S. Bureau of Mines (USBM) study the /low of strategic and critical materials in the economy to delineate and quantify the production areas where metal values are lost. As a result, the USBM developed a generic computerized commodity flow model that is readily amenable to updating. The original model developed for cobalt, with slight modifications, was used to track the flow of manganese. This report follows the flow of manganese through its metallurgical and chemical applications and highlights areas where significant losses occur owing to downgrading, export, or disposal. The study indicates that materials containing 695,000 short tons (st) of manganese were consumed domestically in 1990. Scrap recovery specifically for manganese recycling was insignificant. However, considerable manganese was recycled through processing operations as a minor component of ferrous and nonferrous scrap and steel slag. The major loss category is manganese lost in steel processing, 323,156 st or 46 pet of the 1990 apparent consumption. Most of this loss reports to steelmaking slags. Recovery from slags is technically feasible, but is not economically feasible.

Jan 1, 1995

By R. E. Peterson

Scrap iron is partially oxidized at elevated temperatures in the selective oxidation process to produce iron oxide and a dense residual metal of high purity. Investigation of the process was confined to converting automobile hulks into useful products. In one test series, compressed, sheared automobile scrap was processed at 1,000° C in a 36-foot-long rotary kiln at feed rates ranging from 300 to 1,200 lb/hr. Less fuel was required to maintain the temperature at the higher feed rates because of the heat generated from the burning of the combustibles and the oxidation of the iron. The bulk density of the residual metal exceeded 75 pounds per cubic foot. In an attempt to lower the quantity of contaminants in the residual metal, another test was designed using automobile hulks which had been prepared by ripping, a low-cost method of scrap fragmentation. Before oxidizing the ripped scrap approximately 62 percent of the total copper was removed in a tumbling, screening, magnetic separation and hand-sorting system. Cast iron made from the residual metal obtained by selective oxidation contained 0.15 percent copper; iron oxide scale obtained from the kiln averaged 0.13 percent copper. Pellets made from the scale demonstrated compressive strengths necessary for blast furnace reduction; lead and zinc were removed by volatilization when the induration was performed in a reducing atmosphere.

Jan 1, 1972

By R. J. Evans

The generation and disposal of solid waste from electric utility plants using a lime or limestone wet-scrubbing system and the potential effects on the environment were estimated for 1975 and 1980. The study indicated that in 1975 approximately 5.8 million tons of desulfurization solid waste (50 percent solids) will be generated. In 1980, when it is estimated that desulfurization will become commercially accepted, approximately 71.4 million tons of this material will be generated for disposal and/or utilization. The desulfurization waste material when combined with lime, fly ash, and water may have potential for use as a roadbase material, landfill reclamation, and synthetic aggregate.

Jan 1, 1974

By B. W. Gandrud, G. D. Coe

"INTRODUCTION The Bureau of Mines, United States Department of the Interior, with the cooperation of the University of Alabama and coal producers of Alabama, is making a series of washability studies to obtain technically and commercially important data from the productive coal beds of the State. Based on the system followed in these studies, this report consists of screen-sizing and sink-and-float data on the America and Pratt beds at Gorgas, Ala.SAMPLING AT THE MINESAlthough operations were discontinued in 1929, the accessible openings of the old Gorgas mines of the Southeastern Fuel Co. made possible the taking of samples from the America bed at three openings and from the Pratt bed at two openings. A sample was taken from the America bed at the Klondyke opening; a second was taken about 1 rile south of the Klondyke at the Musgrove America opening, and a third sample was taken about 1-1/2 miles south of the Musgrove-America at the Cricket Lodge opening. A sample was taken from the Pratt bed at Musgrove-Pratt No. 1, which is about 3/4 mile east of Musgrove-America, and a second sample was taken at Musgrove-Pratt No. 2, which is about 3/4 mile west of Musgrove-America. The samples ranged in weight from 1/2 ton to 1 ton and were equivalent to approximately a 2-ton sample from each bed. Figure 1 shows sections of the beds at the places sampled.In addition to the samples for washability study, a seam sample for analysis was taken at each of the places sampled. So as to give a representative seam sample for each of the two beds, these samples were combined in the laboratory in proportion to the thickness of the bed at the places sampled."

Jul 1, 1939

By Byron S. Gottfried

This Bureau of Mines report presents a method for combining the distribution curves at different specific gravities of separation, for a given piece of coal-cleaning equipment and a given raw coal feed, into a single, generalized distribution curve normalized with respect to specific gravity and, therefore, independent of the specific gravity of separation. Illustrative generalized distribution curves, based upon Bureau of Mines collected data on industrial operations, are presented for five different types of coal-cleaning equipment. The well-known concept of probable error is extended to the generalized distribution curve. It is shown that the conventional probable error is directly proportional to the specific gravity of separation. A number of sample calculations, illustrating the use of the generalized distribution curve and generalized probable error, are presented in the appendix.

Jan 1, 1977

By S. J. Hussey

This Bureau of Mines report presents a discussion of the statistical approach to the design of experiments and indicates, by concrete examples, how and when statistical design is essential for obtaining meaningful data with a minimum number of experiments. Every research worker plans his work and designs his experiments in a manner which, based on his experience, seems most rational to him and which he believes will produce the information essential for resolving the problems. If the results obtained are open to multiple interpretations and are not of definitive reliability, the failure of the experiment design to produce the desired information may be due to several causes, These include faulty judgment in selecting the factors to be tested, ignoring the importance of interaction between factors, failure to adequately control test variables, and assuming that meaningful trends in the results can be identified without comparison to a predetermined experimental error. An experienced researcher probably will deduce from the nature of the data obtained that the design is faulty and may by trial and error ultimately arrive at the correct solution to the problem. Statistical methods of planning research minimize the chance of faulty experiment design, embody concrete procedures for testing the validity and reliability of the test data and for indicating mandatory changes in the design, and enable the researcher to obtain meaningful information with the least number of tests.

Jan 1, 1963

By Phillip R. Moyle

In 1985 the U.S. Bureau of Mines evaluated the mineral resources of the Sheep Creek West Wilderness Study Area (ID-111-36A), Owyhee County, ID, for the U.S. Bureau of Land Management. The Wilderness Study Area consists of 11,680 acres centered approximately 20 miles south of Grasmere, 10. It contains no mines, claims, or prospects. No mineral resources were identified; however, a geode occurrence within and adjacent to the Wilderness Study Area, and minor amounts of placer gold along Sheep Creek, may be of interest to rorkhounds and recreational gold panners.

Jan 1, 1986

By Albert L. Toenges

Early in 1944 the Chilean Government expressed a desire for assistance from the Bureau of Mines in a study of the coal deposits, coal-mining methods, and preparation and benefication of coals in Chile. A Memorandum of Understanding setting forth the purpose of the work was executed by the United States Government and the Government of Chile. Parts of this agreement are quoted: On February 4, 1944, the Ambassador of Chile in Washington expressed the interest of his Government in obtaining the loan of a mission of experts to assist in the conduct of a survey looking toward the utilization of the low-grade coals of Chile and the application of such technology as may be developed for the distillation of these coals and the use of oil shales. The matter has since been the subject of correspondence between the Secretary of State and the United States Department of the Interior, and the latter Department has agreed to cooperate with the Government of Chile, through the Bureau of Mines, subject to the following understanding:

Jan 1, 1948

By E. C. Pattee

A mobile spectroscopic laboratory was completed by the Bureau of Mines in 195 to provide a rapid, inexpensive means of field testing samples for beryl¬lium and other associated metals of possible commercial importance. Spectro-copes have been used in laboratories for many years in various types of research and routine analyses, but this spectroscope is probably the first mobile unit. The laboratory provides for spectroscopic, radioactivity, fluorescent, and limited chemical tests of samples. The unit has been a valuable reconnaissance tool. It has been used to search for beryllium, cesium, columbium, tantalum, rubidium, and lithium in Idaho, Washington, and Montana. Several very low grade deposits of these elements were found, and occurrences of other important elements were identified; however, none are of economic importance. The spectroscope permits the detection of elements by analysis of visible light produced when elements in a small powdered sample are volatilized in an electric arc., A total of 70 elements can be detected; 29 can be detected at or below 0.01 percent, Electric power for the arc is supplied by a gasoline motor-driven generator, Equipment is housed in an aluminum van, mounted on a 4-wheel-drive vehicle for easy maneuverability on mountain roads, A trailer with crushing, pulverizing, and splitting equipment permits the reduction of samples to a small representative pulp.

Jan 1, 1963

By John S. Berber

Acids, neutral oils, and pitch were produced by distillation of low-temperature lignite tar and processed to upgrade them into more valuable products: The acids were separated from the distillate and catalytically dealkylated to produce phenol, cresol, and xylenol. Aromatic and naphthene fractions of the neutral oil were converted into phthalic and maleic anhydrides by catalytic hydrodealkylation and vapor- phase oxidation. Paraffins and n-olefins from the neutral oil were processed into alkybenzene sulfonate, a biodegradable substance. Aromatic materials from the neutral oil were also extracted with organic compounds and the extract hydrogenated under pressure to produce jet fuel. The pitch was processed by various means to change its characteristics and make it suitable for similar applications as high- temperature tar pitch, including preparation of carbon black and metallurgical electrodes. In most cases, products obtained from the low-temperature tar were examined for physical and chemical characteristics and for potential commercial utility. Information obtained from this research would be helpful if a new coal- chemical industry based on tar utilization were established.

Jan 1, 1973

By Carlton E. Brown

Broom and Yant6/ recently described a. microprojection method for determining the particle-size distribution and number concentration of samples of dust collected from the air by such samplers as the Owens jet dust counter) and the thermal precipitator8/ . This method was developed to obviate or reduce the eyestrain consequent to the regular filar-micrometer method9/ and to save time and work. The article stated that work was in progress on a micrcprojection method for counting impinger dust samples; this article describes the method developed. ACKNOWLEDGMENTS The assistance of the personnel of the ventilation Department of the Anaconda Copper Miring Co., Butte, Mont., in developing this method and particularly in suggesting a suitable material to use for the microprojector screen is sincerely appreciated. Much of the work was done in the laboratory of the Anaconda Copper Mining Co. on samples collected in Butte mines during a cooperative study with this Bureau.

Jan 1, 1938

By David H. Yee

Because of environmental concerns, the Bureau of Mines investigated an anhydrous chlorination process for the recovery of copper from chalcopyrite, Pelletized concentrate was reacted continuously with chlorine in a vertical shaft reactor at 550° to 750° C to extract copper-iron chlorides and elemental sulfur. The resulting molten metal chlorides drained from the reactor and collected in a receiver while sulfur distilled from the top and condensed in a separate unit. The tests were conducted in a 10-cm-diam reactor constructed of glass and in l5-cm-diam reactors constructed from various refractory materials. A high-alumina ramming mix exhibited the best resistance to molten metal chlorides and elemental sulfur in chlorine atmospheres. A reactor made with this high-alumina refractory was operated for 55 hr under actual chlorinating conditions without suffering any deterioration. Tests results show that more than 96 pct of the chalcopyrite was converted to copper-iron chlorides and elemental sulfur. Good separation of the metal chloride and sulfur products was achieved. After filtration, elemental sulfur of greater than 99 pct purity was obtained.

Jan 1, 1977

By Thomas J. Peters

In 1988, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied the 34,310-acre Diablo Mountain (Additional) study area (OR-001-058), in order to evaluate its identified mineral resources and occurrences. The study area lies along the east shore of saline Summer Lake in Lake County, OR, about 145 miles southeast of Bend and 45 miles northwest of Lakeview. The climate is semiarid and temperate, and the study area is almost treeless. Geologically, the (Additional) study area is in a region of fault block-formed mountains and basins, characterized by interior drainage. The area is mainly underlain by unconsolidated Quaternary and Pleistocene lake and playa sediments, which may include subsurface evaporite mineral deposits and resources. Near the center of the eastern margin of the study area are an occurrence of dolomitic limestone of unknown extent, and an area of basalt outcrop totaling 1.5 square miles. A veneer of windblown sand covers about one-half the study area.

Jan 1, 1989

By N. E. Hanna

The current Bureau of Mines active list of permissible explosives includes 124 brands. Thirteen are gelatinous and the rest are the more commonly used granular ammonium nitrate type. The list of permissible blasting devices comprises five Cardox models.

Jan 1, 1965

By N. E. Hanna

The current Bureau of Mines active list of permissible explosives includes 124 brands. Thirteen are gelatinous and the rest are the more commonly used granular ammonium nitrate type. The list of permissible blasting devices comprises five Cardox models.

Jan 1, 1965

By Carlton E. Brown

Brown and Yant6/ recently described a microprojection method for determining the particle-size distribution and number concentration of samples of dust collected from the air by such samplers as the Owens jet dust counter7/ and the thermal precipitator8/. This method was developed to obviate or reduce the eyestrain consequent to the regular filar-micrometer method9/ and to save time and work. The article stated that work was in progress on a microprojection method for courting impinger dust samples; this article describes the method developed. ACKNOWLEDGMENTS The assistance of the personnel of the Ventilation Department of the Anaconda Copper Mining Co., Butte, Mont., in developing this method and particularly in suggesting a suitable material to use for the microprojector screen is sincerely appreciated. Much of the work was done in the laboratory of the Anaconda Copper Mining Co. on samples collected in Butte mines during a cooperative study with this Bureau.

Jan 1, 1938

By A. J. Kraemer

[The Bureau of Minas for a number of years has been studying the properties of crude petroleum from producing fields in the United States and Western Hemisphere and has published a series of reports on these fields, including oil fields of Texas.5]

Jan 1, 1927

By K. K. Kershner

Sulfide ore concentrates containing cobalt, nickel, copper, lead, and iron were salt roasted and leached on a laboratory scale. More than 95 percent of the cobalt, nickel, and copper was recovered. Heating patterns for salt roasting different concentrates were established. More cobalt, nickel, and copper were recovered from a bulk concentrate composed of a mixture of copper concentrate and iron concentrate. This mixture corresponded roughly with the mixture of these materials in stockpiles in southeastern Missouri. A temperature range of 375° to 400° C. was best for salt roasting. Metal chlorides were leached at a pH of 1 from chloridized charges of concentrates, Although the amounts of cobalt, nickel, and copper extracted were high, the amount of iron dissolved simultaneously interfered with subsequent separation and recovery of these metals. The amount of dissolved iron was reduced substantially by steam treating chloridized charges of bulk concentrate at 300° C. In this way, the ratios of cobalt, nickel, and copper to iron in leach liquors permitted satisfactory separation and recovery of these metals. INTRODUCTION The Federal Bureau of Mines is experimenting with chloridizing reactions.4 5 6 7/ Salt roasting of sulfide ores and concentrates, or their calcines, to form metal chlorides has certain advantages. Chlorides of

Jan 1, 1961

By J. B. Littlefield

[Ata. meeting of the Subcommi ttce on Chemical _ et.lOds of Air Ant:..1ysis of-the American Public Health Ascociation in October 1937, the llse of the impinger for collectinG lcs.d fu.l1e wa:., discussed. The Bureau of Mnes de-cided to obtain infornw.tion on the efficiency of the lerge and midget im-pingers for this purpose y using the electric recipitator as a reference method. 'I'ests ~ ere made aJ,so to aScer ain the effici ency of the recently developed midget i;npi gerS..! for collac ing lead dust. For comparative pur-poses, samples collected by tte large impinger wore included.]

Jan 1, 1938

By Charles E. Semler

The possible utility of selected compositions in the systems SrO-ZrO2-MgO and SrO-ZrO2-Dolomite for commercial refractory products was confirmed in this study. Specifically the compositions of interest are located in the sub-systems SrZrO3-ZrO2-MgO and SrZrO3-ZrO2-Dolomite. Both sub-systems have regions that are not affected by hydration, but the sub-system SrZrO3-ZrO2-MgO has a larger candidate compositional region. Solid state phase relations were determined for the subject systems over the temperature range 1600°C to 1300°C, with compatibility diagrams presented for each. The systems appear to show good refractory character with no apparent low melting compositions. As the compositions of commercial interest lie mostly in the higher ZrO2 portion of each system, information is presented regarding the firing treatment required to develop stabilized cubic ZrO2. A list of suggestions for further study of these systems, to further delineate the characteristics required for possible commercial utilization, is presented.

Jan 1, 1982