Search Documents

By Walter Kawa

In connection with its research in producing synthetic liquid fuels from coal, the Federal Bureau of Mines studied reactions of iron and iron compounds with hydrogen and hydrogen sulfide in batch autoclaves. The Bureau hoped to gain indirect evidence regarding the chemical changes that iron catalysts undergo when they are used in the hydrogenation of coal. The information obtained may be helpful in identifying the active form or forms of iron catalysts. At 450° C., with hydrogen at hundreds of atmospheres and hydrogen sulfide at 1 or 2 atmospheres, the thermodynamically stable form of iron is ferrous sulfide in the case of the metal, magnetite, ferric oxide, ferrous sulfate, ferrous oxalate, or the chlorides of iron. However, complete conversion to ferrous sulfide was not achieved at temperatures of 400° to 500° C. for kinetic reasons. Extensive sulfiding of iron, magnetite, ferric oxide, and ferrous oxalate occurred below 400° C., and some conversion of ferrous sulfate to ferrous sulfide occurred at 400° C. In the hydrogenation of coal, ferrous sulfide is the form of iron likely to be available for heterogeneous catalysis when starting with the metal, oxide, sulfate, or oxalate.

Jan 1, 1960

By C. Kwong, L. H. Rorden, T. C. Moore

This report describes the feasibility test of an electromagnetic method for locating, boreholes, with or without casing, that have been drilled in conjunction with mining operations but whose location with respect to the tunnel is not precisely known. The first tests were conducted with the cooperation of the Kerr-McGee Corporation, Church Rock Mining Operations, New Mexico, in September 1977. These tests demonstrated that accuracies of better than ±15% of range and ±1° of bearing can be achieved with a simple system and setups. Subsequent tests, in January 1978, on a horizontally drilled pipe line river crossing application, by Ti tan Contractors of Sacramento, California, demonstrated that accuracies of better than one-half percent of range and a few tenths of one degree of bearing can be achieved by using refined techniques. The demonstration tests were done at ranges on the order of 100 to 200 feet but the method is capable of working at much greater distances.

Jan 5, 1978

By Susan M. White

Increased coal production, wider use of indiscriminate mining techniques, improved cleaning methods, and greater emphasis on clean fuels is increasing the rate at which wastes accumulate Over the next several years, Colorado Plateau underground coal production is predicted to increase. Currently, mine refuse is deposited in canyons or lowland areas near mines. This study presents information on the nature of coal refuse and disposal practices on the Colorado Plateau. Samples were collected and analyzed to provide information to help formulate alternative methods for reclaiming refuse piles. The analyses were based on determining the capability of unmodified refuse to provide a suitable medium for plant growth. Local topsoils which would be used in reclamation were used as standards. Potential environmental hazards were assessed also. A general cost analysis was done for both surface and underground disposal and the advantages and disadvantages of each were assessed. Several problems were identified which, if solved, would increase the effectiveness of state regulatory programs.

Jan 1, 1982

By Thomas A. Davidson

The Bureau of Mines Helium Field Operations has developed a method for determining the helium-3 CHe) content of natural gas and mixtures eontaining 0.5% to 100% helium. The helium is preconcentrated by passing samples through anhydrone, a liquid-nitrogen-cooled chareoal trap, and a titanium absorption trap. The mass spectrometer used to analyze the samples is tuned to 3He at mle ::=; 3.016. Hydrogen deuteride (HD+) interference is minimized by the titanium absorption trap and high instrument resolution. Sample measurements are compared with identically made measurements of a gravimetrically prepared primary standard. The method has a limit of detection of 0.15 ppb with a relative deviation of 13% below the 1~ppb level. The relative deviation is less than 7% for gases eontaining over 100 ppb 3He. The helium isotope ratios of natural gases from the Bureau's Tuck-Trigg Dome Red Cave, the Bush Dome Red Cave, and the Bush Dome Brown Dolomite Formations are distinguishable from one another and from the isotope ratio of crude helium produced from the Panhandle-Hugoton Gasfield.

Jan 1, 1990

By Margaret R. Egan

This Bureau of Mines report presents results from experimental studies on wood crib fires in an intermediate-scale fire tunnel. Gas concentrations, smoke particle characteristics, heat release rates, and ventilation rates were determined. These measurements form a data base for wood, which can be used with previous analyses for coal and future studies of other mine combustibles, to comprehend the potential hazards of these materials in underground mine fires. A knowledge of the combustion products emitted from these materials will benefit fire detection and control. Results show the changes in burning rate and heat release rate produced by different crib configurations and ventilation rates. Also included are the effects that the burning rate has on smoke characteristics and gas production.

Jan 1, 1986

By Kevin Malone

Mercury, or quicksilver as it is often called, has many applications in modern technology. Used principally in electrical apparatus, industrial contol instruments, insecticides and fungicides, electrolytic preparation of chlorine and caustic soda, chemical processes, pharmaceuticals, and dental preparations, the liquid metal has unusual properties that make it a preferred material for many industrial uses. United States consumption of mercury during the past 40 years shows a rising trend. In all except 4 years, U.S. production has been less than the domestic requirement, and imports, principally from Spain, Italy, and Mexico, have supplied most of the deficit. After World War II, domestic output decreased rapidly until 1950, when it was the lowest in the 100 years covered by production records. Higher mercury prices since 1950 have reversed the decline in domestic output and reduced the gap between U.S. production and consumption. Domestic output in 1958 was the highest in peacetime since 1883; however, the nation still imported 28 percent of its mercury requirements from 1950 to 1960 the price of mercury was high as a result of industrial applications of the mercury cell, the impact of the cold war and the Korean war, and the Government stockpiling program. The stockpiling program, in effect, put a floor under mercury prices even though only 9,428 flasks of domestic mercury went into the stockpile under the original program which ran from July 1954 to December 31, 1957. Under an extension of the program, an additional 17,463 flasks was purchased.

Jan 1, 1962

By Ronald B. Stotelmeyer

This report summarizes studies of 28 National Forest roadless areas in Montana completed by the U.S. Bureau of Mines (USBM) in the period 1974-1993. It also briefly describes 20 areas for which field studies have not been conducted. All 48 of these roadless areas have been recommended for addition to the National Wilderness Preservation System or proposed as special management areas by the U.S. Forest Service (USFS) or the Montana congressional delegation. The Bureau studies indicate which parts of the roadless areas have a high likelihood for mineral-resource development. They also show where mineral production has occurred in the past and where abandoned mine workings (possible hazards) would be encountered. The number of mine and prospect workings found are a measure not only of surface disturbance, but of areas not wilderness in character. For the purposes of this report, mine refers to a property which produced (or is currently producing) a mineral commodity, a prospect is a property which has been explored but has no record of production.

Jan 1, 1994

By A. J. Kraemer

This paper is the second and concluding report of the results of the twenty-fourth semiannual survey made by the Bureau of Mines of motor gasoline marketed in the United States. The first report7 on this 1931 survey gave the results of the examination of the gasoline samples in accordance with the new Federal specification for United States Government Motor Gasoline.8 The present paper reports results of the examination of the gasolines for color, doctor test, gravity, end point, per cent recovered, copper-dish gum, and steam-oven gum. The retail price and the tax at the time each sample was taken are also reported.

Jan 1, 1932

By G. E. McClelland

As part of its mission to assure an adequate domestic supply of metals essential to the Nation's welfare, the U.S. Department of the Interior, Bureau of Mines, investigated a particle agglomeration technique as a means for improving the flow of leaching solution through heaps of clayey or finely crushed, low-grade, gold-silver ores. Bench-and pilot-scale experiments showed that the percolation rate of cyanide leaching solution was markedly enhanced by mixing the ore with a portland cement binder, moistening the mixture, and mechanically agglomerating and aging the feed prior to heap building and leaching. The rate of gold and silver recovery markedly increased because of the increased, uniform percolation of leaching solution through the agglomerated feed. The use of concentrated cyanide solution instead of water during the agglomeration procedure decreased the leaching time required to obtain maximum recovery. Results of bench-and pilot-scale experiments are discussed.

Jan 1, 1981

By Henry M. Harris

Low-carbon shales from 65 deposits and 11 sources of coal-mine waste in western Oregon and Washington were tested in a rotary kiln for their suitability as raw material for expanded aggregate. Shales from 41 sources bloated enough to produce crushed, expanded aggregates, weighing less than 65 pounds per cubic foot in the preliminary tests. The samples were judged on the basis of processing qualities, physical properties, and size and uniformity of the source. Nine low-carbon shale deposits and three coal-mine waste sources were selected for more extensive bloating tests and for examination of the expanded aggregates in concrete shapes. Composite samples from these 12 sources and from 2 commercial operations, when processed for testing in concrete shapes, had bulk densities ranging from 37.S to 72.9 pounds per cubic foot. Damp-cured concrete shapes made with these aggregates had bulk densities ranging from S6 to 119 pounds per cubic foot, and all but three of the lightweight concretes had crushing strengths ranging from 3,270 to 6,810 p.s.i. Properties of the lightweight concretes were compared with those of concrete shapes made with commercial aggregates, and with sand and gravel.

Jan 1, 1962

By Joseph D. Davis, G. S. Scott, Palmer B. Place

In the course of investigations made by the Bureau of Mines in cooperation with the Trent Process Corporation, into the properties of mixtures of oil and coal, a comparative study was ma.de of the 'behavior of these mixtures and their cons ti tuents on destructive distillation. Mixtures of a petroleum oil and bitminous coal were first distilled under carefully controlled conditions, and then charges of the eame oil and coal were distilled separately under similar conditions. The quantity and quality of the distillation products were determined, and. resul. ts were compared. This comparison furnished a basis tor judging whether grea, ... er values in products can be obtained by distillation of oil and coal in mixtures than· b:, their separate distillation. In making the mixtures, the method used in t~e Trent process for cleaning coal was followed. The paste or plastic emulsion of oil and coal obtained is called "amalgam".••• When finely pulverized wet coal is mixed with approximately one-third its weight of. oil and agitated with a large excass of waj;er, the coal and oil agglomer-. ate to form a paste or amalgam. A large portion of the extraneous ash original.17 in the coal remains suspended in the water, with which it can be decanted from the amalgam. Ir the latter is now thoroughly drained and kneaded after the manner ot working butter, most of the excess water enclosed can be removed. This, .in brief, constitutes the Trent process for cleaning coal, The effectiveness of the process for cleaning coal has been studied••••. by the Bureau, and the results of the study show, in general, a high ash reduction an:l good recovery of combus ti bl e f'rom coals of medi ,mi and hi~ rg,nk. With coals of tht lowest rank, such as li@!Rlites, the process is only moderately auccessf'ul, owing to the difficulty attending the preparation of coherent amalgams, Oil losses to wate~ and refuse are small, and apparently it would be practical to rotate the same oil in the cleaning process if some efficient method were devised for recovering it from the amalgam, so a distillation process naturally suggested itself.

Dec 1, 1921

By Wesley Holmes

Concentrating, nodulizing, and smelting studies were conducted at the Albany Metallurgy Research Center of the Bureau of Mines to determine whether (1) western iron ores of the type found in the Carter Greek deposit near Dillon, Mont., could be utilized; (2) concentrates of acceptable grade with good iron recovery could be attained by wet-magnetic beneficiation; (3) nodulized concentrates could be smelted with reductants readily available in Montana; (4) iron concentrates could be smelted without prior agglomeration; and (5) high-purity iron could be produced directly from high-grade concentrates, Three small samples and two tonnage samples from the Carter Creek deposit were uniform in chemical composition, and their iron content averaged about 31 percent. They were found to be banded gneisses, and magnetite was the principal iron-bearing mineral.

Jan 1, 1962

The London Metal Exchange began its first official session of aluminum trading on Monday, October 2, LME prices based on 3-month forward contracts opened Monday at 52.4 cents per pound, fell midway through the week to 52.3 cents and ended Friday at a high of 52.7 cents. For the week, LME metal averaged 52.5 cents. Although Reynolds Metals Co. and Aluminum Co. of American continued in September to value unalloyed 99.5 percent aluminum ingot at 53 cents per pound, other producers were at higher positions of 55-57 cents. Alcan Aluminum Corp. of Alcan Aluminum, Ltd., a Canadian producer, increased prices for its U.S.-marketed ingot by 2 cents to 55 cents per pound, effective September 21. New York merchants increased ingot quotes by approximately 0.5 cents to 52.8-53.5 cents per pound.

Jan 1, 1978

By C. J. Mains

The gas -flow oil-shale retort is a continuous, crass flow, gas -to -broken solid heat-exchange system in which heat is transferred by convection from the gas to the solide.2/ This type of heat transfer presents a problem of analysis that cannot be solved by methods in common use. Solution of this problem is necessary for design, operation analysis, and predict ion wherever that type of heat exchanger is used. This report embodies a method for calculation of heat transfer coefficient and temperature histories of gas and solid in the gas- flow retort operating at equilibrium conditions. Detailed calculations are presented to show the application of the method explained in this report to conditions of an actual run made in the gas-flow retort. Although used here for a specific case, the method is applicable to all heat exchangers that are characterized by continuous, crossflow, gas -to-broken solid heat transfer. INTRODUCTION In any direct, gas -to -broken solid heat -transfer system, it is difficult to measure the temperatures of the gas and solid inside the heat exchanger. The driving force for heat transfer between the two media in the bed there- fore usually is unknown. The major resistance to heat transfer is in the gas film surrounding the solid particles, and the thickness of this gas film is neither uniform nor can it be determined readily. It is well to point out also that determination of the surface area of the particles is of poor accuracy. Since the driving force, the major resistance, and the surface area in the heat-transfer system are such uncertain quantities, It is not feasible to calculate the heat transfer by usual methods. All of the fore- going statements are true of the gas-flow retort; as a result, efforts were made to determine apparent heat-transfer coefficients and temperature histories of gas and solid in the heat -exchange bed by calculation using those data that were available. The heat -transfer coefficient calculated has the following dimensions: B .t .u. per second, °F., cubic foot of bed volume, where heat - transfer coefficients normally have the units; B .t .u . per hour, square foot, °F. Only the Schumann-Furnas formulas may be used to determine the heat- transfer coefficient and temperature histories in this type of heat exchanger.

Jan 1, 1953

By L. R. Burdick, R. Wiggers, J. F. Berkley

"INTRODUCTION On February 23, 1944, Solid Fuels Administrator Harold L. Ickes stated that the existing fuel shortage made it necessary to utilize a great surplus of freshly mined anthracite ranging in size from Barley (No. 3 Buckwheat) downward through the smaller sizes. As a part of the program to increase the use of such coal, field trials of mixtures of bituminous slack coal and anthracite Barley were made on industrial-size stokers at many fuel-burning plants. The following covers the test information it was possible to accu-mulate during the work of initiating the use of these mixtures at the plants.SUMMARY AND CONCLUSIONSField tests of various mixtures of bituminous slack coal and anthracite Barley on industrial-type stokers show that the use of such mixtures is very practicable and that it is possible to change and usually to adjust to an improved condition the characteristics of a fuel bed of eastern bituminous slack coal by the addition of proper amounts of anthracite. The improved uniformity of the fuel bed of single-retort stokers makes possible less manual attention to the bed. Air flow through the fuel bed is affected.Smoke is decreased. In general, the fly ash and also the unburned combustible in the fly ash and refuse are increased. Clinkering in the fuel bed is generally lessened. The peak-load carrying capacity of the stoker is definitely affected, usually adversely for the higher percentages of anthracite."

May 1, 1946

By Spencee L. Willett

In 1984, at the request of the Bureau of Land Management, the U.S. Bureau of Mines conducted mineral surveys of the 20,508-acre Blue Lakes (NV-020-600) and 5,142-acre Alder Creek (NV-020-600D) Wilderness Study Areas (WSAs) in northwestern Humboldt County, Nevada. The WSAs are part of an upthrown, north-south trending fault block associated with the Basin and Range province. Both areas are predominantly underlain by the Cretaceous Duffer Peak pluton which intrudes Triassic metasediments and Jurassic plutonic rocks to the east and Permian Happy Creek volcanics to the south. In the Alder Creek WSA and in the southwest portion of the Blue Lakes WSA, Duffer Peak granodiorite and Happy Creek volcanics are overlain by Tertiary basalt. No active mines exist within the Blue Lakes WSA; but, several prospects, claims, and mineralized outcrops are in the south and northeast portions. No mineral resources were identified but samples from discontinuous, vein-type deposits contained anomalous amounts of gold, silver, copper, lead, zinc, molybdenum, antimony, and uranium. Very fine, residual gold was detected in nine alluvial samples collected from a small deposit in the southwest corner of the WSA; average gold value was $3.58 per cubic yard (at $350/ounce). Two mines, several prospects, and mineralized outcrops adjacent to the Blue Lakes WSA contain mineralized, irregular structures which do not appear to extend into the Blue Lakes study area.

Jan 1, 1986

By John W. Buch

Hydraulic cutting tests made on samples of Pennsylvania anthracite (3,700 psi and 260 gpm) were promising enough for the Bureau to establish a full scale experiment in an anthracite mine. Water pressure and quantity for mining anthracite were arbitrarily established at 5,000 psi and 300 gpm (1,000 hp). For full-volume flow, hydraulic pressure is controlled by orifice size with the displacement pump. The hydraulic jumbo was designed for maneuvering on pitches from 0° to 20° in any direction and for a coalbed ranging in thickness from 10 feet 6 inches to 15 feet. All motions of the jumbo are by oil hydraulics. Jet flow is controlled (start-stop) at the face, through an interlocked pushbutton system. One button is in the operator's cab; one, at the pump station; and one (a safety shutoff), near the mining face. To December 1962, 7,400 tons of bed material had been mined at an average rate of 0.800 ton per minute, with an average power requirement of 14.125 kilowatt-hours per ton. In January 1963, the objective was changed from an engineering-development basis to a research basis--to determine, ultimately, the most efficient level of operating characteristics for maximum response, as measured by mining-out rate. This research phase of the project is not yet complete, but conclusions, and the method of arriving at them, will be made the subject of another Bureau publication. It should be noted that as of December 1963 nearly 13,000 tons of bed material had been mined, at rates as high as 1. 3 tons per minute for a complete face advance.

Jan 1, 1965

By R. H. Thompson

Six different types of blasting caps, mainly of the type used in coal mines, were evaluated to determine both their 1lF and DC characteristics. Two of the caps were of foreign manufacture. All the American made caps had "no-fire" (0.1% firing probability with 95% confidence, as determined by the Bruceton test) levels above 0.04 watts. One of the caps of foreign manufacture had a "no-fire" level of 0.023 watts. A worst case analysis of blasting cap pick up of RF power in coal mines was performed and safe distance curves were generated.

Jan 8, 1973

By K. J. Miller

A two-stage froth flotation technique was developed in the laboratory to separate fine-size pyrite from coal. The process consists of the initial flotation of a 15-percent solids coal slurry with a minimum of frother; the coarse, free pyrite and other refuse are removed in the tailings. The froth product from this first stage is then repulped and treated with a coal depressant, a pyrite promoter, and a frother to float the remaining fine-size pyrite or pyrite attached to coal particles. With the two-stage process, the pyritic sulfur content of a Lower Freeport bed coal sample was reduced from 1.78 percent to 0.75 percent in the first stage, and from 0.75 percent to 0.27 percent in the second stage with good clean coal recovery.

Jan 1, 1972

The number of railroad coal cars (open top hoppers), dominated rail car orders and deliveries in 1975 according to announcements made February 11, by the Association of American Railroads and the American Railway Car Institute. Acting to keep ahead of increased coal production, the railroads installed 21,748 new coal cars in 1975, the most since 1957. The 1975 installation resulted in a net increase of 6,560 coal cars and an overall gain of 4.5 percent in the total capacity of the hopper car fleet. With most of the new coal cars going into unit train service --where car utilization is greatest --the railroads actual coal-carrying capacity was increased far more than 4.5 percent. The AAR estimated that unit train operations now move 50 percent of all rail-hauled coal compared to only 42 percent 2 years ago. COBALT - The Societe Miniere de Tenke Fungurume (SMTF) copper-cobalt project in Zaire reportedly was suspended in January for an indefenite length of time. According to officials, the deferment resulted from a number of adverse factors, one of which was exceptional increases in capital costs. The project was scheduled for completion in early 1978, with an eventual production of 14.3 million pounds of cobalt per year. Reserves of cobalt were reported to be 505 million pounds. SMTF is a consortium and includes American, British, French, Japanese, and Zairian interests.

Jan 1, 1976