Search Documents

By D. W. Frommer

Composite samples of nonmagnetic taconite from the western Mesabi range were evaluated by reductive roasting, fine grinding, and magnetic separation to determine potential sources of concentratable material. Although large tonnages of nonmagnetic taconite are known to occur in the western Mesabi district, these materials are not as yet a commercial source of iron ore. The technique employed permits the evaluation of individual composites and blocks of composites in terms of responsiveness to a process of potential commercial significance. The 159 composites, from open-pit mines located between Grand Rapids and Chisholm, Minn., were evaluated in the following sequence: 1. Minus 8-mesh material was roasted at 500° C. in hydrogen. 2. The roasted are was ground to one or more sizes in the minus 100-to minus 400-mesh range. 3. The roasted ground ore was magnetically separated in a Davis tube. 4. Composites were classified according to degree of grinding required to produce minimal concentrates. (Minimal concentrates are herein defined as those containing less than 10 percent silica, and responsive composites as those yielding minimal concentrates.)

Jan 1, 1962

By J. A. Woolf, E. S. Leaver, N. K. Karchmer

"In the cyanidation of silver ore, the need of oxygen is well recognized. Various methods have been introduced for supplying the oxygen. In usual practice, air is the source of oxygen and the methods of application are mechanical.This article gives the results of touts made to show the rate of dissolution of silver from each of the common silver minerals in cyanide solution, under conditions similar to those used in the practical recovery of silver from its ores. The effect of oxygen in aiding the dissolution of the silver from each mineral is also shown by a comparison of the methods of supplying the oxygen. Oxidation by preliminary roasting (500°C.) of each mineral sample gives the maximum extraction of the silver by treatment with cyanide.Each silver mineral5 used in these experiments was as pure as could be obtained from the mineral dealer. In their natural occurrence, silver minerals are not usually free from mineral impurities. They are usually closely associated with other minerals often forming, a complex mixture. The form of crystallization, the proportions, and properties of the diluent that incases or has been dispersed with the silver mineral may decidedly affect the dissolution rate of the silver from each mineral. While the following results should aid in the cyanidation of silver ores, each ore should be studied from the basis of the form and condition of the silver that is to be recovered.All the tests reported in this article were made on synthetic samples, prepared by mixing the particular silver mineral with clean sea sand. Each mineral was ground in an agate mortar to pass 100-mesh before mixing with the sand which had previously been ground in a porcelain pebble mill to 100-mesh. Such proportions of each mineral and the sand were used as to give a head assay of approximately 20 ounces of silver per ton to the synthetic sample.Agitation was carried on in stoppered bottles approximately one-third full of pulp, method apparently supplied all the atmospheric oxygen that would be taken up by the solution under usual conditions, because tests conducted in open bottles did not show increased recovery,"

Jan 1, 1931

By Frank J. Wiebelt

Under a general program to extend the resources of mineral deposits, the Bureau of Mines examined the Quien Sabe antimony mine in October 1948. The preliminary evaluation demonstrated that a diamond-drill program was warranted co establish the tenor and persistence of the veins and permit an estimation of antimony reserves. The Bureau of Mines conducted a diamond-drilling program on the property from December 1949 to May 1950. Ten holes aggregating 2,483 feet were drilled. Nine of the holes encountered antimony-bearing vein material.

Jan 1, 1956

By Andrew A. Cochran

Laboratory-scale research was conducted by the Bureau of Mines to develop a new process for treating electroplating and other wastes. Various acid and alkaline cyanide wastes were combined under controlled conditions to neutralize the wastes and to almost completely precipitate the metals and cyanides. The metals were subsequently recovered for recycling; the cyanides can also be easily recycled. The process was successfully used to treat the major types of electroplating and etching wastes, containing Cd, Cr, Cu, Ni, and Zn, and to treat both concentrated and dilute wastes. The economic aspects of treating concentrated electroplating, etching, and anodizing wastes are especially attractive because of the low cost of mixing two wastes, the high value of the recovered metals, and the simplicity of the recovery procedures. The filtrates from the waste-plus-waste step were relatively harmless compared with the original wastes and met Public Health Service standards for free cyanide content. Free cyanide ions were not detected in most of the filtrates; the limit of detection was 0.03 ppm. Only small amounts of HCN were produced during the neutralization; the HCN was collected and neutralized.

Jan 1, 1974

By F. W. Wessel

This report summarizes Bureau of Mines laboratory tests of four tungsten¬-bearing materials of various grades, The test work has demonstrated that the dry reaction between sodium carbonate and scheelite is best conducted at 900° C. or a few degrees less. The sodium carbonate requirement, in addition to the stoichiometric equivalent of the scheelite, is in some inverse relationship to the grade of tungsten in the ore. Residence time and particle size exert a definite but minor control on the reaction. Pressure-digestion tests on an impure concentrate indicate the technical feasibility of extraction by this process. INTRDUCTION Over 100 years ago Oxland discovered that tungstic oxide could be removed from wolframite and converted to a soluble form by reacting the mineral with a soluble alkaline salt at elevated temperatures. He patented this discovery, and this patent 4/ since has been the basis for most tungsten extraction. Much literature exists on this process and its modifications, and the characteristics and possibilities of the reaction are quite well defined.

Jan 1, 1956

By G. E. McClelland

As part of its mission to assure an adequate domestic supply of metals essential to the Nation's welfare, the U.S. Department of the Interior, Bureau of Mines, investigated a particle agglomeration technique as a means for improving the flow of leaching solution through heaps of clayey or finely crushed, low-grade, gold-silver ores. Bench-and pilot-scale experiments showed that the percolation rate of cyanide leaching solution was markedly enhanced by mixing the ore with a portland cement binder, moistening the mixture, and mechanically agglomerating and aging the feed prior to heap building and leaching. The rate of gold and silver recovery markedly increased because of the increased, uniform percolation of leaching solution through the agglomerated feed. The use of concentrated cyanide solution instead of water during the agglomeration procedure decreased the leaching time required to obtain maximum recovery. Results of bench-and pilot-scale experiments are discussed.

Jan 1, 1981

By R. R. Wells, K. C. Vincent, A. O. Ipsen

"INTRODUCTION The Philipsburg Mining District, Granite County, Mont., has been the largest producing area for battery-grade manganese (70 percent MnO2) in the United States since the First World War. Two companies, the Trout Mining Division of the American. Machine & Meals Co., and the Moorlight Mining Co., have intermittently mined and milled 120 to 250 tons of 25-percent manganese ore per day for the production of concentrates of this grade.Investigation of the district by engineers of the Federal Geological Survey and Bureau of Mines indicated that further exploration and develop¬ment would make available additional oxide and carbonate manganese ores for milling and production of metallurgical-grade manganese. If the battery-grade producers converted their plants to the production of metallurgical-grade concentrates, their production also could be increased through greater recoveries.Until February 1, 1944, the Metals Reserve Company, through its agent, the Sunshine Mining Co., purchased milling-grade manganese oxide and carbonate are for stock-piling at Philipsburg. After that time, only carbonate ore was purchased. Based upon the assumption that the stock pile was a true cross-section sample of the producing area, metallurgical studies were made on representative samples from the Metals Reserve stock piles. Testing also was conducted on two other samples of Philipsburg oxide manganese ore obtained by engineers of the Bureau of Mines from the Little Dandy claim of the Donlan group and from the Marie mine. All ore samples tested were found to be amenable to concentration by ore-dressing methods for the production of concentrates that when sintered met Metals Reserve Company specifications for metallurgical-grade manganese."

Nov 1, 1947

By C. L. Severy

The Reeder No. 1 well was drilled by the Bureau of Mines in cooperation with the Geological Survey as agents for the Defense Plant Corporation. The well is south of Crescent Junction near Thompson, Grand County, Utah. It was started May 5, 1942, and completed August 3, 1942, for the purpose of con-firming the presence of magnesium salts in a deeply buried bed. Drilling was done under contract by the Mack Drilling Co. This report contains an outline of the physical features of the well, a brief history of drilling, and a description of the deposits and occurrences of oil and gas encountered in the drill hole. The work performed by the Bureau of Mines is described in considerable detail, with particular emphasis on drilling procedure and sampling. The report is concluded with a brief description of core-sample preparation for analyses. Appendix A comprises a log of the drill hole, and appendix B is a tabulation of analyses of cores.

Jan 1, 1949

By R. P. Vinson

The Bureau of Mines conducted a series of tests to determine how well the Bendix BDX 60, the Gilian HFS 113U, the MSA Fixt-Flo, and the Spectrex PAS-3000 dust sampling pumps control the flow rate at 2 L/min. These tests were performed because users need to know the performance characteristics of sampling pumps to select the pump that best satisfies their sampling requirements. Long-term (6- to 8-h) flow stability at various backpressures was examined in relation to the flow control tolerance of ±5% of the flow, the level imposed by Federal regulations; four of the five Bendix pumps did not meet the criterion for this test, which was passed by all other pumps tested. Flow control recovery times were measured at transient backpressures; all pumps evaluated met the criterion for this test. The low-flow indicators of the sampling pumps were tested; only two Bendix pumps and one Gilian pump met the criterion of indicating a flow change greater than ±5%. In the pulsation flow measurement test all of the pumps passed, with pulsating flows greater than 20 Hz. The Bureau also evaluated the manuals accompanying the sampling pumps. All were judged adequate except the Spectrex manual, which was judged poor.

Jan 1, 1985

By A. R. Taylor

This report describes the design, construction, and operation of a low temperature adiabatic calorimeter for measuring heat capacities of solids or liquids from 60° to 300° K. A brief discussion of the basic theory involved in chemical thermodynamics and the problems involved in obtaining accurate experimental data is presented. The operation of the calorimeter was tested by measuring the heat capacity of a sample of benzoic acid obtained from the National Bureau of Standards over a temperature range of 60° to 300° K. The measured heat capacity values of the benzoic acid compared favorably with similar values obtained by the Bureau of Standards, the maximum deviation being 0.5 percent. THEORY A brief discussion of the basic theory involved in chemical thermodynamics will illustrate the applications of heat capacity data and the problems involved in obtaining accurate experimental data.

Jan 1, 1962

By C. J. Mains

The gas -flow oil-shale retort is a continuous, crass flow, gas -to -broken solid heat-exchange system in which heat is transferred by convection from the gas to the solide.2/ This type of heat transfer presents a problem of analysis that cannot be solved by methods in common use. Solution of this problem is necessary for design, operation analysis, and predict ion wherever that type of heat exchanger is used. This report embodies a method for calculation of heat transfer coefficient and temperature histories of gas and solid in the gas- flow retort operating at equilibrium conditions. Detailed calculations are presented to show the application of the method explained in this report to conditions of an actual run made in the gas-flow retort. Although used here for a specific case, the method is applicable to all heat exchangers that are characterized by continuous, crossflow, gas -to-broken solid heat transfer. INTRODUCTION In any direct, gas -to -broken solid heat -transfer system, it is difficult to measure the temperatures of the gas and solid inside the heat exchanger. The driving force for heat transfer between the two media in the bed there- fore usually is unknown. The major resistance to heat transfer is in the gas film surrounding the solid particles, and the thickness of this gas film is neither uniform nor can it be determined readily. It is well to point out also that determination of the surface area of the particles is of poor accuracy. Since the driving force, the major resistance, and the surface area in the heat-transfer system are such uncertain quantities, It is not feasible to calculate the heat transfer by usual methods. All of the fore- going statements are true of the gas-flow retort; as a result, efforts were made to determine apparent heat-transfer coefficients and temperature histories of gas and solid in the heat -exchange bed by calculation using those data that were available. The heat -transfer coefficient calculated has the following dimensions: B .t .u. per second, °F., cubic foot of bed volume, where heat - transfer coefficients normally have the units; B .t .u . per hour, square foot, °F. Only the Schumann-Furnas formulas may be used to determine the heat- transfer coefficient and temperature histories in this type of heat exchanger.

Jan 1, 1953

By Jennifer Riefenberg

The U.S. Bureau of Mines has long recognized the hazards associated with rock burst activity in underground mines. Concern over lost lives and resources prompted this study to further characterize rock burst occurrence as related to microseismicity and mining. A period of over 1,079 days of mining with 101 bursts, where microseismicity rates and blasting were recorded, was used in this study. Statistical analyses investigated relationships between (1) rock burst occurrence versus blasting, (2) rock burst size versus damage, (3) rock burst occurrence versus average micro seismicity rates, and (4) rock burst occurrence versus local mine geometry. Statistical analyses showed that 91% of all rock bursts occur with blasting while only 3% of all rock bursts occur, apparently, independent of blasting. Additionally, the long-term average daily micro seismicity rates appear to dictate when blasting will trigger rock bursts. Time series analysis on the daily microseismicity resulted in model equations that may be used to forecast the daily microseismic activity.

Jan 1, 2010

Throughout October, U.S. producers priced unalloyed 99.5 percent aluminum ingot at 53¢ per pound. Dealers, in last month's domestic market, were quoting unalloyed ingot at a range of 45.5¢-46.3¢ per pound. Costa Rica recently issued a proposal to Japanese aluminum smelters to participate in an integrated aluminum-refining project which would include bauxite development. The project reportedly would include a 600,000-kilowatt hydroelectric power station, a 600,000-metric-ton-per-year alumina plant, and a 300,000-ton-per-year primary aluminum smelter. Two U.S. firms--Aluminum Co. of Amerjca (Alcoa) and Martin Marietta Co.--and several European aluminum smelters are also said to be interested in taking part in this project. Alcoa conducted a feasibility study for the Costa Rican Government in 1970 and estimated the bauxite reserves to contain 150 million metric tons.

Jan 1, 1977

By Homer J. Ballinger

The Alma, Degraff and other mines controlled by the Mon-Ark Mining Co. comprise one of the more important groups of zinc-lead mines in Christian County, Mo. The mines were first operated in .1857 and produced more than 5 million pounds of lead from rich, shallow ore deposits. Recent exploration and development led to the discovery of zinc sulfide ore at a depth of 165 to 214 feet in the northern part of the Alma mine. After examination of these mines in September 1942 by Bureau of Mines engineers, investigation of the extension -of the Alma mine and of the depth of mineralization at the other mines appeared justified in order to encourage the production of additional zinc and lead for war purposes. Twenty-nine churn-drill holes totaling 6.463 feet of bore were completed by the. Bureau from September 1943 to January 1944.

Jan 1, 1948

By Robert W. McKibbin

The Bureau of Mines conducted laboratory tests to determine the slurry transport and deposition properties of coal waste. A 188.5-ft pipe test loop was constructed with instruments to measure density, flow, and power and discharge, suction, and differential pressures. A 20-ton ample of Western coal waste was crushed and screened to 100 pct minus 1/2 in. Eight loop tests using this graded waste were run at slurry densities ranging from 1.15 (25 wt-pct solids) to 1.46 (60 wt-pct sol-ids) 0 The resultant friction-'pressure gradients ranged from 0,06 to 0.24 ft of water per foot of 4-in standard steel pipe. Particle-size degradation was significant.. In a typical loop test lasting 25 min, the minus 200-mesh fraction increased from 19 pct to 34 pct. Deposition tests showed that without the use of a flocculant, the slurries would not dewater when left to stand for 1 week. With flocculant, additional water was releas2d; however, the settled slurries remained thixotropic. Further testing is necessary to determine their suitability for use as backfill material in active mines.

Jan 1, 1983

By John W. Buch

Hydraulic cutting tests made on samples of Pennsylvania anthracite (3,700 psi and 260 gpm) were promising enough for the Bureau to establish a full scale experiment in an anthracite mine. Water pressure and quantity for mining anthracite were arbitrarily established at 5,000 psi and 300 gpm (1,000 hp). For full-volume flow, hydraulic pressure is controlled by orifice size with the displacement pump. The hydraulic jumbo was designed for maneuvering on pitches from 0° to 20° in any direction and for a coalbed ranging in thickness from 10 feet 6 inches to 15 feet. All motions of the jumbo are by oil hydraulics. Jet flow is controlled (start-stop) at the face, through an interlocked pushbutton system. One button is in the operator's cab; one, at the pump station; and one (a safety shutoff), near the mining face. To December 1962, 7,400 tons of bed material had been mined at an average rate of 0.800 ton per minute, with an average power requirement of 14.125 kilowatt-hours per ton. In January 1963, the objective was changed from an engineering-development basis to a research basis--to determine, ultimately, the most efficient level of operating characteristics for maximum response, as measured by mining-out rate. This research phase of the project is not yet complete, but conclusions, and the method of arriving at them, will be made the subject of another Bureau publication. It should be noted that as of December 1963 nearly 13,000 tons of bed material had been mined, at rates as high as 1. 3 tons per minute for a complete face advance.

Jan 1, 1965

By Charles K. Rose

The Cebolla Creek titaniferous iron deposits near Powderhorn in southern Gunnison County, Colo., were examined by the Federal Bureau of Mines as part of an overall program to investigate the Nation's titanium and iron resources. The deposits occur around the periphery of the Iron Hill stock, which underlies an area of about 12 square miles. Concentrations of magnetite, ilmenite, and perovskite arc localized along fractures in the pyroxenite stock. Mineralogical studies of composite surface samples collected in 1956 showed that most of the iron is present in ilmenite-bearing magnetite. Perovskite is the chief titanium mineral in the magnetite-rich and augite-rich types, and sphene is the principal titanium mineral in the placer material. The mica-rich rock contains approximately equal amounts of perovskite, ilmenite, and sphene.

Jan 1, 1960

By Richard J. Leary

The inputs of capital and labor to support future iron ore production were developed by the Bureau of Mines from projections of iron demand and estimates of capital and labor requirements. Trends in technologic change and the organization of production were analyzed. Labor requirement schedules for iron ore mining and beneficiating were constructed from aggregate inter-temporal trends and 1970 cross-sectional analysis of mines and mills. A sup-ply schedule of the capital requirement for mine-mill-pellet plants was developed from U.S. and Canadian experience. The structure of demand for iron to the year 2000 was examined as well as the availability of resources. Projections of capital and labor requirements to 2000 were constructed under two international patterns of iron ore supply to the United States. The most likely model is for a continuation of the 70 percent United States-30 percent foreign shares, expanding at an average 2.0 percent growth rate to 2000, and supported by a cumulative gross capital investment of $3.8 billion constant 1967 dollars and a labor force in the United States of 29,800 by 2000. The information content of projections is discussed, and the possible effects of international forces on supply are considered. A generalized methodology for estimating capital and labor requirements in other mineral industries also is included.

Jan 1, 1975

By R. H. Thompson

Six different types of blasting caps, mainly of the type used in coal mines, were evaluated to determine both their 1lF and DC characteristics. Two of the caps were of foreign manufacture. All the American made caps had "no-fire" (0.1% firing probability with 95% confidence, as determined by the Bruceton test) levels above 0.04 watts. One of the caps of foreign manufacture had a "no-fire" level of 0.023 watts. A worst case analysis of blasting cap pick up of RF power in coal mines was performed and safe distance curves were generated.

Jan 8, 1973

By B. P. Martinez

In response to a request from the President, the Department of the Interior joined with other agencies in a comprehensive study of the land and water resources of the New England-New York region. As part of this study, chemical engineers of the Bureau of Mines have visited 1,025 mineral-industries plants to inventory the waterborne wastes of mineral origin, discharged by the mineral industries of the New England-New York region. Four-hundred and sixty-two of these plants disposed their wastes to a public sewer of some type, but waste control remains a problem for moat of them. The 1,025 plants are discussed in main industry groups according to their production: Chemical and allied products. Stone, clay, and glass products. Iron and steel and their products (except machinery). Nonferrous metals and their products. Electrical machinery. Machinery (except electrical). Transportation equipment. Miscellaneous mineral industries.

Jan 1, 1956