Search Documents

Water infiltration control techniques are designed to reduce the total volume of water entering an underground mine, and thus, reduce the volume of mine water discharge During the development of underground mines, water may be encountered in various quantities This water must be pumped from the mine during active mining, and in many situations, the weight of water removed will be more than the total weight of mineral extracted After abandonment of the mine, infiltrating water either floods the mine workings or discharges from the mine (27, 127) Infiltrating water may enter underground mines from above, below, or laterally through adjacent rock strata Earth fractures such as faults, joints, and roof fractures resulting from surface subsidence are commonly primary causes of water entrance Into abandoned underground mines Factors affecting the quantity of water entering a mine will be the depth of the mine, location of water bearing strata, and ground water flow patterns Investigations of the quantity of water entering underground coal mines have found the average rate of infiltration to range from approximately 6,262 to 10,280 liters per hectare per day (670 to 1,100 gal/acre/day) (27) Water flowing through underground mines flushes pollutants from the mine and may result in their discharge to the environment A reduction in the amount of flow usually results in a reduction in total pollution load discharging from the mine The techniques discussed in this section can be used to reduce the volume of surface and groundwater available to enter the mine system and transport pollutants The selection of a control technique will depend upon the characteristics of the mine system and the expected cost effectiveness of the technique In order for water infiltration control to be effective in controlling mine drainage pollution, the reduction in mine water flow must not be accompanied by an increase in concentration of pollutants (127) REFERENCES 2, 27, 51, 58, 127, 132

Jan 1, 1975

By Quintin A. Aune

This report presents the results of a field and laboratory study by the Federal Bureau of Mines, in cooperation with the California Division of Mines, of the swelling-type bentonite deposits in the Vallecitos area in San Benito County, Calif. The purpose of the study was to learn if these large deposits contain bentonite of sufficient quality and quantity to be of economic value as an oil-well drilling mud additive. Large amounts of bentonitic clays are used by the petroleum industry as well as the steel industry in California. Additional amounts may be required in the near future as a concrete or earth-fill admixture in constructing dams and canals in the California Central Valley. Depletion of some local clay deposits and loss of others to military installation areas have given new emphasis to the need for developing new bentonite deposits in California.

Jan 1, 1959

By R. D. Leitch

[The accepted theory of acid formation in coal mines with the subsequent appearance of the acid in coal-mine drainage, is oxidation of iron pyrite and subsequent solution and hydrolysis of the iron sulphate formed. It has also been found that 5 gobbed sections and worked-out areas, where there is usually an abundance of iron pyrite-bearing, materials in contact with air, are the sections that make the most important contribution to the quantity of acid drainage. It would thus seem obvious that if oxygen can be kept out of contact with tae acid-forming materials in tie- sections mentioned the amount of acid in coal-mine drainage could be reduced markedly and corrosion problems with mine pumping equipment and general stream pollution mitigated thereby. Although the efficiency of the suggested remedy as been borne out by laboratory experiments6, it has appeared desirable to substantiate the laboratory work by field observations in so far as pertinent data are available. It has been difficult to learn of mines or sections of mines about to be sealed, whereby an actual comparison of the drainage before and after sealing can be made. In view of that difficulty it has been necessary to devote attention to a comparison of the character of the water from areas already sealed with that from open but otherwise comparable sections of the sane mine. Previous cork has shown that the acidity of drainage in different parts of the same mine may vary, but if it can be shown also that the water from sealed areas is with but fen exceptions less acid than the otherwise similar open sections of tae same mine, the laboratory finding will be supported in a practical gray. This report presents some of the evidence that has been obtained.]

Jan 1, 1930

By H. P. Greenwald

About mid-December 1936, the safety director of a large coal corporation visited the authors at the Bureau's Experimental coal mine to discuss a rock-dust barrier he had invented primarily for use in trackless entries of coal mines. The rock dust in this device was carried in its original paper containers and means were provided for ripping these open so that the dust might be scattered in the path of an explosion. The inventor termed the device a "bag barrier", and this term has been adopted in the present paper for convenience. At that time the device was in an early stage of development, and the inventor felt that the barrier should be tested to determine whether it had enough promise of being successful to justify further development. The matter was taken under consideration and finally three tests were made during the week of February 15, 1937. It was concluded that while the device did stop an explosion in two of the three tests, it was much loss effective than ordinary rock dusting, and that too few data were obtained to permit direct comparison with tests of other barriers. Apparently, the conditions under which the device could, be successful 'Were somewhat limited, out the limits could not be defined without additional tests.

Jan 1, 1938

By E. O. RHODES

This report is one of a series written by members of the Solid Fuels Mission to Germany describing wartime developments in the mining, prepara- tion, and utilization of coal. This mission was organized early in 1945 under the auspices of the Technical Industrial Intelligence Committee, which cooperated with a counterpart British Committee. In some instances; engi- neers from other allied countries cooperated. The Solid Fuels Mission operated under the direction of a steering committee headed by Dr. C. J. Potter, Deputy Solid Fuels Administrator. The personnel of the mission consisted of H. F. Yancey, in charge, J. W. Buch, Thomas Fraser, L. L. Newman, and L. D. Schmidt of the Bureau of Minos; H. H. Lowry, Director of the Coal Research Laboratory, Carnegie Institute of Technology; H. J. Rose, Vice-President and Director of Research, Bituminous Coal Research, Inc.; and F. H. Reed, Chief Chemist, Illinois Geological Survey. E. 0. Rhodes, Manager, Development Section, Tar Products Division, Koppers Co., Inc., served on the mission for the Chemical Subcommittee of 1.I.I.C. in Europe. His assignment was the investigation of the coal-tar industry. In this connection he prepared this report on the German Low- Temperature Tar Industry as a companion to his provious report on the German High-Temperature Tar Industry (Bureau of Mines Information Circular 7409). Because of Mr. Rhodes' extensive experience in these fields and the impor- tance of the subject material to the coal producers and those utilizing coal-tar products, both reports are issued by the Bureau of Mines. Over fifty reports were written by the members of the Solid Fuels Mis- elon. These, together with microfilms of supporting data obtained in the course of the investigations, are on file at the Foreign Documents Group, Technical Reports Section, Bureau of Mines, Pittsburgh, Pa., where they are available for examination. Copies of reports available in printed form may be ordered from the Department of Commerce, Office of Technical Services, Washington 25, D. C. Check or money order accompanying order for printed reports should be made payable to the Treasurer of the United States. A Bibliography of Scientific and Industrial Reports, covering all ma- terials and subjects and giving instructions for obtaining the desired items, has been published weekly by the Office of Technical Services. Effective July 1, 1948, the Bibliography of Scientific and Industrial Reports will be prepared monthly instead of weekly and on a more selective basis. issue, which will be the first monthly issue, will be available about July The July month thereafter through June 1949. Annual subscriptions and orders for individual copies starting with the July 1948 issue should be addressed to the Department of Commerce, Office of Technical Servicos, Washington 25, ur, and be accompanied by chock or money order made payable to the Troas- Bibliof the United States. Annual subscriptions for monthly issues of the Bibliography of Scientific and Industrial Roports will be $10. Individual issues will cost $1 per copy. Foreign subscriptions will be $14 per year and $1.50 por copy. tions listed in the Bibliography of Scientific and Industrial Reports should All orders for reports in microfilm or photostatic type of reproduc- ורי

Feb 1, 1949

ESTABLISHMENT of an effective inspection system has been held essen¬tial to any international agreement that may be designed primarily to curb the testing of nuclear weapons. A number of reports and papers already have described basic inspection concepts and appraised various pro¬cedures, techniques, and methods as to their probable effectiveness in detecting and identifying violations under such agreement. This report results from a study of only one part of the contemplated inspection system, specifically the final phases embracing onsite investigations and mine examination techniques. The results and reports of earlier work were reviewed in detail, and subjects that were found to have been exhaus¬tively evaluated are recognized by reference and not redescribed here. In other instances, previously described techniques, methods, and clues were revaluated to define more clearly their practical value to the final objective of an onsite inspection. Previous documentation does not refer to a number of subjects, techniques, tools, clues, and methods considered by the study; this report treats these in detail, even though when applied singly or collectively their practical value may be questionable.

Jan 1, 1962

By W. Hermanson

This report, which covers the period from January 16 to October 21, 1974, describes the work performed in compliance with the requirements of contract no. H0242028 and modifications 1 and 2 thereto. The purpose of the contract was to further reline and modify three of the canopies (shuttle car, loader, and roof drill) which were developed under contract no. H0220031, and to conduct further testing and demonstration of the relined designs. Modifications I and 2 involved conducting further in-mine evaluations of the face. drill and cutter canopies, also developed under contract no. H0220031. In addition to the canopy modifications, the contract involved an evaluation of an operator's seat concept for a shuttle car which was developed for the USBM by another contractor.

Jan 1, 1974

By Gary L. Hundley

The Bureau of Mines has devised and demonstrated a process for recovering Ni and Co from low-grade domestic laterites. The process consists of four major steps: (1) reduction roast, (2) ammoniacal leach, (3) solvent extraction, and (4) electrowinning. Several solid-liquid separation steps are required that affect the economics of the overall pro-cess. In this study, two techniques for solid-liquid separation, centrifugation and thickening, were investigated. This report presents the results of (1) laboratory and pilot plant studies to determine parameters for sizing centrifuges and thickeners and (2) an economic study of the two techniques, based on the requirements of a commercial-size (5,OOO-tpd) laterite processing plant. Sizing and other equipment-related recommendations, based on data from the Bureau's studies, were obtained from commercial manufacturers. The costs of thickening and centrifugation, including all the unit operations affected, were determined by the Bureau's process evaluation group. The total operating costs ~or separation using the two techniques (including depreciation on the capital cost of equipment) were found to be quite close: $17.26 per ton of laterite for centrifugation and $18.15 per ton of laterite for thickening. For centrifugal separation, the greatest cost was found to be the initial capital cost for the separation equipment; using thickeners, the greatest cost was for re-agent recovery.

Jan 1, 1984

By R. E. Siemens, Gary L. Hundley

The Bureau of Mines has devised and demonstrated a process for recovering Ni and Co from low-grade domestic laterites . The process consists of four mmaajjoorr steps : ( 1 ) reduction roast , ( 2 ) ammoniacal leach , ( 3 ) solvent extraction , and ( 4 ) electrowinning . Several solid - liquid separation steps are required that affect the economics of the overall process . In this study , two techniques for solid - liquid separation , centrifugation and thickening , were investigated . This report presents the results of ( 1 ) laboratory and pilot plant studies to determine parameters for sizing centrifuges and thickeners and ( 2 ) an economic study of the two techniques , based on the requirements of a commercial - size ( 5,000 - tpd ) laterite processing plant . Sizing and other equipment - related recommendations , based on data from the Bureau's studies , were obtained from commercial manufacturers . The costs of thickening and centrifugation , including all the unit operations affected , were determined by the Bureau's process evaluation group . The total operating costs for separation using the two techniques ( including depreciation on the capital cost of equipment ) were found to be quite close : $ 17.26 per ton of laterite for centrifugation and $ 18.15 per ton of laterite for thickening . For centrifugal separation , the greatest cost was found to be the initial capital cost for the separation equipment ; using thickeners , the greatest cost was for reagent recovery .

Jan 1, 1983

By JOE SIERAKOSKI, W. R. Hardwick

This paper , which describes mining methods and practices at the Johnson Camp copper -zinc mine , Coronado Copper & Zinc Co. , Cochise County , Ariz . , is one of a series being prepared by the Bureau of Mines on mining methods , practices , and costs in various mining districts of the United States . Johnson Camp is in the eastern foothills of the Little Dragoon Mountains in secs . 23 , 24 , 25 , and 26 , T. 15 S. , R. 22 E. ( fig . 1 ) . The mining property is in the low, rolling foothills at an altitude of slightly over 5,000 feet above sea level ( fig . 2 ) . The area is covered with scattered grass and small desert shrubs . The climate is mild , with hot summers and mild winters . The average annual precipitation is about 12 inches . The nearest surface water is the San Pedro River , some 12 miles west of the mine . The property is owned by the Coronado Copper & Zinc Co. , Los Angeles , Calif . This report gives a brief history of the property , describes the general geology of the area and of the ore deposits , outlines the methods of prospecting and exploration , and gives the methods of sampling and of estimating ore reserves . Development and stoping methods are explained . Underground transportation , ventilation , mine drainage , and safety measures also are described . The last section gives a brief description of the milling practice .

Jun 1, 1957

By J. R. Hoskins

A recent survey of 23 vein-type metal mining operations in several western states discloses that some of the more serious deficiencies in ventilation technology are associated with inordinately high levels of mine resistance. This problem has progressively increased over many years of operation (without adequate remedial action) as mines have become extended in depth. Where two shafts form the downcast and upcast airways of a relatively deep mine, the whole of the mine air volume must pass through each shaft in turn. Since at least one of these shafts contains hoisting equipment, structural members are necessary to support the rigid guides and shaft walls. These offer high aerodynamic resistance. In some deep mines, a single shaft of this nature may represent upwards of one-half of the total mine resistance. The second shaft, depending upon its design, may represent an additional one-third of the mine resistance. Therefore, the various working levels throughout the mine contribute only the small remaining amount of the total mine resistance.

Jan 1, 1972

By L. O. Bacon

This Bureau of Mines report summarizes the results of laboratory work in the design of instrumentation for obtaining the dynamic tensile strength of rock at minimum loading. Minimum loading is defined as the lowest tensile loading by pulse reflection to cause fracturing. The instrumentation for obtaining dynamic tensile strengths of rock cores evolved into the use of a compressed-air pellet gun to impact one end of a rock core, suspended by wires, at increasing increments of air pressure. Maximum strain was measured on most or all of the impacts, and the strain at fracture of the core was obtained by extrapolating the pellet velocity-strain curve to the pellet velocity at fracture. Stress at tensile fracture was obtained from the maximum s train, and the dynamic Young's modulus was calculated from the rod velocity by using simple rod theory.

Jan 1, 1962

By S. R. Droes

The U.S. Bureau of Mines investigated calcium fluoride (CaF2) assisted sulfuric acid (H2S04) leaching as an alternative to the melting-quenching procedure to obtain Mn from domestic manganese silicate resources. Pyroxmangite [(Mn, Fe) Si03] ore containing, in percent, 34.4 Mn, 22.8 Si, 2.6 Ca, and 1.3 Fe was leached in a 500-mL resin kettle. Ninety-six percent of the Mn was extracted under conditions of 330 g/L ore, 245 g/L H2S04, 35 g/L CaF2, 90' C, and 2 h. To incorporate electrowinning in recovering Mn, the ore was leached with a simulated spent anolyte solution containing, in grams per liter, 12 Mn, 140 H2S04, 130 (NH4)2S04 (ammonium sulfate), and 5 CaF2. Manganese extraction of 92 pct was achieved from 130 giL ore leached at 90° C in 3 h. The Fe, silica (SiOJ, and other impurities were precipitated from the pregnant solution by neutralization with ammonia (NH3). Manganese of greater than 99-pct purity was deposited at a cathode current density of 50 mA/ cm2 at 30° C, with a current efficiency of 65 pet in a two-compartment cell. A flowsheet was proposed for the leaching and electrowinning procedure.

Jan 1, 1990

By J. E. Murphy

A method is being developed by the Federal Bureau of Mines for recovering lead metal from galena without the generation of SO2. Lead chloride is obtained by leaching lead concentrate at a temperature of approximately 100° C with FeCl3 solution: PbS + 2FeCl. " PbC1 2 + 2FeC1 2 + S. Electrolysis of the PbCI 2 product in a fused-salt bath results in deposition of molten lead metal at the cathode and evolution of chlorine at the anode. The chlorine can then be absorbed in the spent leach solution to regenerate FeCl3 for recycling. Optimum electrolyte composition was a PbC12-LiCl eutectic containing 7.6 wt-pct LiCl. The PbCl2-NaCl eutectic also proved satisfactory. Electrolysis in the PbCl2-LiCl bath at 450° C yielded 99 pct current efficiency at a current density of 5 amp/in2 with an energy requirement of only 0.24 kW-hr/lb metal produced. This compares with 98 pct current effi¬ciency and 0.26 kW-hr/lb metal produced for the PbCI2-NaCI bath. A typical lead deposit contained less than 100 ppm total detectable metallic impurities. At the low temperature employed for electrolysis, there was essentially no vaporization of Pb or FbC12.

Jan 1, 1974

By L. A. Neumeier

The Bureau of Mines evaluated creep and other properties of extruded Zn-30 pct-AI alloys containing 0 to 0.7 pct Mg. The alloys were extruded both above and below the Zn-Al eutectoid temperature of 275° C. Creep behavior is defined for the alloys as extruded and after various heat treatments. Tensile properties, hardness, thermal expansivity, impact resistance, and microstructures are given. The alloys, either with or without magnesium, required substantially less pressure for extrusion near 275° C than at higher or lower temperatures. The alloys containing magnesium exhibited significantly greater hardness, tensile strength, and creep resistance, but much lower ductility than the 2n-30 pct Al alloy. The properties were very sensitive to the processing conditions.

Jan 1, 1971

By J. Owens

Advanced materials development ranks as one of the most important high-tech industries of the future in the United States. Recent breakthroughs can be attributed to advanced computer technology, powerful mathematical models, and more precise analytical tools that enable scientists to examine and control properties of materials as never before. Discoveries now being made are providing many industries with opportunities to improve product lines, fabrication techniques, product reliability, and so forth. More¬over, industries, such as space, medicine, and defense, which require stringent: design and perfomance specifications in highly competitive world markets, increasingly demand these new materials. The definition of advanced materials used here is one that has been adopted by the U. S. Bureau of Mines: Those materials which have been developed over the past 30 years or so, and which are being developed at present, that exhibit greater strength, higher strength-density ratios, greater hardness, and/or one or more superior thermal, electrical, optical, or chemical properties, when compared with traditional materials.

Jan 1, 1991

By d&apos, Kathleen J. Amico

THIS SUAMMARY is shown in Minerals Yearbook volumes I and III of this series on mineral production in the United States, its island possessions, the Canal Zone, and the Commonwealth of Puerto Rico, and on the principal minerals imported into and ex- ported from the United States. The several commodity and area chapters contain further details on production. A summary table comparing world and U.S. mineral production also is included. Mineral production may be measured at any of several stages of extraction and processing. The stage of measurement used in the chapter is normally what is termed "mine output." It usually refers to minerals in the form in which they are first extracted from the ground, but customarily includes for some minerals the product of auxiliary processing operations at or near mines.

Jan 1, 1962

By Raymond J. Isherwood

The U. S. Bureau of Mines has investigated the domestic primary and secondary lead smelting and refining industries to determine the economic impacts of existing and proposed environmental, health, and safety regulations. The impacts are assessed in terms of capital and operating costs for existing and alternative smelting/ refining technologies. Industry response to regulatory implementation is estimated and quantified in terms of import value from lost lead production. For the primary lead industry, regulatory compliance may add up to 1.15 ¢/lb refined lead to operating cost for rehabilitated plants. Alternative smelting/refining methods could reduce net operating costs by as much as 4.36 ¢/lb refined lead. Capital expenditures would vary from $750 to $1,000 per annual mt of smelter capacity. Secondary lead smelter operating costs would increase about 3.8 ¢/lb refined lead to comply with existing regulations. Capital expenditures would average about $124 per annual mt of smelter capacity. Implementation and enforcement of proposed regulations would result in closure of the primary lead industry and additional expenditures for compliance by the secondary lead industry. Enforcement of the most extreme proposed regulations would force the secondary lead industry to close.

Jan 1, 1988

By Joe H. Skidmore

This paper, describing mining and milling methods and costs at the Gold Hill mine, is one of a series being published by the Bureau of Mines. Boise Basin, in which the geld Hill mine is located, is in the central part of Boise County, Idaho, about 30 miles by air line northeast of Boise. The mine, owned and operated by Talache Mines, Inc., is at the southern end of the town of Quartzburg. About 115 to 125 tons daily is mind by square-setting and is treated in an amalgamation plant.

Jan 1, 1938

By W. D. Walker

The trend toward encouragement of worker participation in accident prevention in the coal mines of the United States is not new; however, it has been given added impetus in recent years and is now definitely progressing. It has been found by experience that, although there are many approaches to a mine-safety program that will include the workers themselves as well as their supervisors, no one way is suitable under all circumstances. It requires the concerted efforts of many agencies working along parallel lines toward a common goal. The following seven principal agencies, using somewhat different methods, are listed to illustrate how this problem is approached throughout the coal-mining industry 1. Federal Bureau of Mines. 2. State mining departments (in individual States where coal is produced). 3. Programs conducted by individual mine operators. 4. Programs conducted by mine workers' organizations (unions). 5. Institutes, societies, and other educational organizations. 6. Coal operators' associations (regional and national). 7. Universities, college, and high schools. Each of the seven approaches to safety are discussed briefly, and their methods end contributions, such as publications and other activities, are listed.

Jan 1, 1953