Search Documents

By Larry A. Haas

The chemistry of current or potential SO2 removal processes can be placed into four categories: (1) reduction, (2) Liquefaction, (3) direct dissolution, and (4) oxidation. Methods that involve reducing SO2 to elemental sulfur appear promising since this product can be easily handled, shipped, and stock- piled. Unfortunately, SO2 cannot always be reduced directly when other oxidizing agents are present. Thermodynamic data indicate that some oxidizing reagents will also consume reductant at the reduction temperature. A two- stage process can be applied to waste gases that contain excessive quantities of oxygen, nitrogen oxides, and water vapor. The best sorbent for the first stage appears to be a nonalkali or nonalkaline earth medium since this medium more readily releases the SO2 for reduction in the second stage.

Jan 1, 1973

By G. H. Gronhovd

This report describes the design and initial operation of a slagging gasification pilot plant installed by the Bureau of Mines at the Lignite Research Laboratory, Grand Forks, N. Dak., in 1958-59. The tests covered in this report were conducted over a period of about 2 years, beginning in April 1959. The pilot plant was designed for eventual operation at pressures ranging from 400 to 600 p.s.i.g. (pounds per square inch gage); however, for the preliminary test reported here, the gasifier was fitted with a low-pressure slagging section and operated at atmospheric pressure and at 80 p.s.i.g. The reason for using a low-pressure slagging section for initial operation was to facilitate modifications in design during the development of a reliable slagging procedure.

Jan 1, 1962

By W. A. Stickney

This report summarizes the results of laboratory tests of five samples of low-grade phosphate ores from Idaho. The laboratory test work has demonstrated that by grinding, desliming, and flotation a portion of the siliceous gangue can be removed. The highly carbonaceous ores responded successfully to treatment after preroasting, to produce a plus-30-percent-P205 product. It has been found that highly siliceous ores, as represented by the samples treated, are more readily amenable to concentration than ores high in calcium carbonate. Of the five samples tested, four were amenable to concentration to a product containing over 30 percent P205. One sample, from the Conda, second bed, was not amenable to mineral-dressing treatment to produce a plus-25-percent-P205 product.

Jan 1, 1955

By Curtis A. Jones

Continuing interest has been shown in developing processes for extracting nickel and cobalt from low-grade domestic deposits of these metals and in improving existing methods. Of special concern is the nickel-recovery installation at Nicaro, Oriente Province, Cuba, operated for the General Services Administration. The Bureau? of Mines felt that a bibliography would help familiarize personnel at various Bureau of Mines stations and General Services Administration contractors with extraction methods both in the United States and in foreign countries. When this task was under way it became apparent that to compile a complete bibliography would require considerable time, so it was decided to limit the first part to the later literature and issue it independently, thus making it available sooner. The present work supplements the first part and extends the coverage to the earliest years of nickel and cobalt metallurgy.

Jan 1, 1959

By H. P. Hermance

The Ely mine, which at one time was the largest producer of copper in the United States, has been idle for the past 30 years. A remarkably continuous ore shoot probably averaging 100 feet wide and 19 feet thick was mined on about a 25° slope for 3,400 feet on the incline. The ore was massive sulfides containing chalcopyrite, pyrrhotite, pyrite, and sphalerite. The estimated production of the Ely mine is 400,000 tons of ore averaging 3.3 percent copper. Because of the critical position of copper during the recent war, a search for extensions and recurrences of parallel ore shoots at the Ely deposit seemed warranted. The Bureau of Mines surveyed selected areas by geophysical methods, diamond-drilled nine holes, and sampled mine dumps during its investigations, which began in 1942 and terminated in 1946. The diamond drilling totaled 5,229 feet. The logs of the holes include chemical analyses of mineralized sections.

Jan 1, 1949

By N. O. Johnson

This is one of a series of-Information Circulars dealing with mining and milling methods and costs at mines in various districts in the United States. The Hog Mountain gold mining district is of the northern edge of Tallapoosa County, in the east central part of the State of Alabama. The district is equally close to Goodwater and to Alexander City, both stations on the main line of the Central of Georgia Railroad. From Alexander City the mine is reached by 13 miles of graded road, traveling in a northeast direction. In dry seasons the road is good; in wet weather it is bad but passable. Improvements are being made constantly on the road, so that in the near future the gravel road should be good under all weathered conditions.

Jan 1, 1936

By Lloyd Williams

1. This investigation shows that the Poplar Creek is the most important bed in Scott County from a production standpoint. Although the Poplar Creek bed contains the largest reserve, the Big Mary has a larger recoverable reserve. Estimates of reserves also have been made for the Pewee, Red Ash, Windrock, Upper Pioneer, Jellico, and White Oak beds. 2. Known measured and indicated reserves of coal, based on a minimum bed thickness of 14 inches and on 1,800 short tons per acre-foot of coal in place, are estimated to be 143 million tons as of January 1, 1954. Of this total, 74 million tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1956

By Larman J. Heath

Preliminary results of an explosive fracturing-solvent injection heavy oil recovery experiment conducted by the Bureau of Mines at a shallow oil reservoir near Bartlett, Kans., are given. Three wells 35 to 50 feet apart were drilled to a depth of 360 feet, and an open hole interval from 300 to 350 feet in the Bartlesville Sandstone Formation was explosively fractured with 3,000 pounds of pelletized TNT in each well. Laboratory tests were made on cores obtained from these wells to confirm the suitability of using an aromatic-type solvent. Injection of a 74-percent aromatic solvent was begun into one well and continued intermittently for approximately 2 months. Crude oil production amounted to 29.6 bbl, or 11.7 percent of the total oil con¬tained within the three-well interwell zone.

Jan 1, 1972

By C. E. Augustine, B. A. Landry, P. Nicholls

"Wien bituminous coal is burned in a hand-fired up-draft boiler used for heating purposes it has a decided tendency to produce smoke. A design of furnace and a method of firing and attendance that are satisfactory for fuels low in volatile matter, as anthracite or coke, are not necessarily Satisfactory for bituminous coals. It is therefore becoming common practice to use a special design of furnace for bituminous coals, in order to facilitate the combustion of the volatile matter and soot. This is done by (1) providing a larger combustion space to give more time for the combustion, (2) construction that will produce a better mixing of the gases and secondary air supplied over the fuel bed, or (3) keeping the gases at a higher temperature by preheating the secondary air, as may be done by surrounding them with refractory surfaces, or causing them to pass through a fuel bed of hot coke. A furnace may be built to use any or all of these methods of smoke prevention.In Bureau of Mines Technical Paper 303, Blizard5 and others give tests on a large heating boiler when burning coke, anthracite, and bituminous coal. Certair alternative furnace arrangements were used, but there was no material change in the furnace design for the various fuels. Since that time the manufacturer has made modifications in design to adapt it for use of bituminous coal, and additional tests have been made to determine how this change affected the production of smoke and the efficiency of the boiler."

Jun 1, 1929

By Irving Hartman

The results of the first experimental study by the Bureau of Mines on the explosive properties of metal powders were published in 1945. Since that time the explosibility of numerous other industrial dusts and powders has been investigated. Part of this information has been published, but most of the data has not been released to date. This paper summarizes the results of experiments on 22 samples of titanium, zirconium, thorium, uranium, and hydrides of these metals. The major part of the investigation was made under cooperative agreement with the Atomic Energy Commission.

Jan 1, 1951

By Gilbert L. Forst

The objective of this program is to identify and evaluate superior, lightweight substitutes for selected coal mine roof support concepts such as crossbars, posts, and crib blocks. Engineering analysis and concept design identified, through tradeoff studies, that some materials are promising, from a technical standpoint, as support substitutes: E-glass reinforced polyester resin, high strength low alloy steel, aluminum, and very high early strength (VHE) cement. An economic analysis indicates that none of the lightweight substitutes are economically competitive with wood on an initial cost basis; however, in terms of life cycle costs based on current dollars, the high strength low alloy steel appears competitive for crossbars, and the VHE cement and E-glass/resin appear competitive for posts.

Jan 1, 1978

By H. H. Yancey

In this information circular is presented a summary of the more important articles that nave appeared in the literature pertaining to the experimental work and to the commercial operation of the froth-flotation and Trent processes as applied to the cleaning of fine coal.

Jan 1, 1933

By Dennis R. Dolinar

Physical property tests were conducted on drill core from three exploratory holes on the Naval Oil Shale Reserve near Anvil Points, Colo. Data and regression analysis curves are presented. Data obtained above the Mahogany zone were used to estimate the potential zone of surface effects from under-ground mining. Single specimen testing was primarily used to obtain Mohr's envelope and subsequent rock properties. The technique is shown to provide satisfactory results for this rock type with a significant reduction of core preparation and testing time.

Jan 1, 1981

By Jerry G. Craig

The Bureau of Mines has developed a computerized oil and gas well data retrieval system from studies of the waterflood potential of a producing reservoir. This system stores pertinent information about each well completed in a reservoir and facilitates selection and manipulation of large volumes of data. Use of the system enables reservoir information to be supplied rapidly, accurately, and at less expense.

Jan 1, 1971

By C. W. Davis

This is the first of a series of papers being; prepared as the work progresses in a study of the hydrometallurgy of manganese. The investigation is being made in an endeavor to make possible the utilization of lour-grade domestic manganese ores. The value of a hydrometallurgical process for manganese depends on the present and future uses for manganese products.

Jan 1, 1930

By Thomas C. Mowatt

Preliminary Bureau of Mines studies of mafic igneous rocks collected from the Rabbit Creek area, northwestern Alaska, indicated concentrations of platinum (412 to 1,406 ppb) and palladium (343 to 892 ppb) in five of eight samples analyzed. The samples represent boulders and cobbles of mafic/ultramafic rocks from this locality. They are not from outcrop. Petrologically, (on the hand specimen scale) the samples are crudely to well-layered and are troctolitic ± gabbroie in character, with primary igneous mafic minerals strongly altered. Small patches of interstitial sulfide minerals, including chalcopyrite, bornite, pyrrhotite, pyrite, and covellite are associated with these altered zones and elsewhere through the specimens. Copper values ranged from 0.1 to 0.3 pct in samples analyzed semiquantitatively; nickel, cobalt, and chromium contents are low. Chemical, mine alogic, and petrographic relationships suggest that the rocks of similar character outcropping in northwestern Alaska could also be considered as prospective for- concentrations or platinum, palladium, and copper.

Jan 1, 2011

By H. J. Hager, B. W. Gandrud, G. D. Coe

"INTRODUCTION The reduction of washery losses of marketable coal is a phase of coal preparation important to many of the Alabama coal producers. The problem has wide scope, and this report deals with but one of its several aspects. The investigation on which this report is based was made by the Southern Experiment Station of the Bureau of Mines with the cooperation of the Alabama By-products Corporation and the University of Alabama. The Alabama Byproducts Corporation provided samples of table middlings from its Colta washery on the Mary Lee bed at Flat Creek, Ala.PRACTICE AT THE COLTA WASHYAt Colta run-of-mine coal is crushed in a hammer mill in closed circuit with 5/16-inch square-mesh vibrating screens and tabled without classification on eight rectangular-deck wet tables. The coal is more friable than the bone normally present, and hence the bone is concentrated in the coarser sizes. An unclassified feed of this character can not be tabled with high efficiency to low ash content because of the sizing action of a concentrating table, which is such that when the tables are adjusted to exclude the coarse bone from the washed coal, a large amount of fine coal is lost in the middlings. At the time this investigation was undertaken there was no market outlet for middlings, with the result that middling products had to be discarded with the refuse."

May 1, 1939

By John Nagy

The effect of low percentages of methane (0 to 5 pet.) in an air atmosphere on spark initiated explosions of coal dust was investigated. With low dust concentrations (0.1 to 0.4 oz./cu, ft.), small amounts of methane increase the explosion pressure; with larger dust concentrations (0.5 to 2.0 oz./cu. ft.), small amounts of methane decrease the explosion pressure. The rate of pressure rise of a coal dust explosion increases with increase in methane concentration; about 3 to 4 pct. further addition of methane yields a decrease in the rate of pressure rise. Convection currents created by the air or gas blast used to disperse dust produce an increase in explosion pressure and rate of pressure rise. The minimum explosive concentration of the coal dust decreases about linearly as the concentration of methane increases from 0 to 5 pct. The explosion pressure increases linearly as the initial pressure within the chamber increases. Similarities between coal dust and methane explosions are indicated, INTRODUCTION During coal mining, methane occluded in coal or adjoining strata is liberated into the mine atmosphere,4 Normally, the methane is diluted and swept away by the ventilating air. Under some conditions, through accidental disruption of the ventilation system, sudden outburst, or because insufficient fresh air is supplied to a working place, low percentages of methane may be present during mining operations. If it is permitted to accumulate, methane itself presents an explosion hazard; its limits of explosibility arc approximately 5 and 15 pct. The effect of low percentages of methane on the explosibility of coal dust was studied to provide a broader understanding of the hazards of ignition and explosion and thus to facilitate development of control

Jan 1, 1961

By H. Polat, Q. Hu, M. Polat, S. Chander

"The electrostatic charge on spray droplets of ionic surfactant solutions and coal particles was measured and the results were correlated with the dust collection efficiency. When various surfactant were added, the magnitude of the droplet charge increased significantly and it was observed to be a function of surfactant type and concentration. The concentration of maximum droplet charge coincided with surfactant concentration where maximum collection efficiency was observed for these surfactants. Particles of coal also carried substantial amount of charge magnitude of which seemed to be a function of coal rank.Based on the results presented in this paper, it was concluded that ionic surfactant primarily act as a strong electrostatic charge inducer for droplets. Due to interactions between these highly charged droplets and naturally charged particles, the efficiency of droplet-particle collisions play a primary role when compared to the wetting and engulfment phenomenon which could only follow a successful collision. INTRODUCTIONWater spray are widely used to suppress airborne dust in mine atmospheres (Walton and Woolcock, 1960; Kobrick, 1970; Hamilton, 1974; Jayaraman et al., 1986). Several investigators have considered the use of surfactants to enhance the effectiveness of water sprays especially for difficult to wet particles such as those of coal (Glanville and Wightman, 1979). The capture of dust particles by water droplets involves droplet-particle collisions, adhesion of particles to droplets, and engulfment of particles into droplets. Surfactants affect these sub processes through their influence on droplet charge, surface tension, and wetting. The last two mechanism have been thoroughly studied in recent years (Walker et al., 1952; Cohen and Rosen, 1981; Glenville and Haley, 1982; Chander et al., 1988; 1991). However, little attention has been paid to the role of electrical charge on particles and droplets on the collision and adhesion of spray droplets and dust particles."

Nov 1, 1995

By Reinhardt Thiessen

Views and conceptions of the origin, composition, and general nature of coal differ so widely that to determine the real extent of actual knowledge is no easy matter. The chemist finds difficulty in attacking the chemical problems and the engineer lacks a broad chemical basis for the study of his problems. Thus the economical and efficient utilization of coal in the industries suffers from a lack of knowledge of the composition of coal itself. Most scientists interested in this matter, as has been brought out in discussions during the recent investigation of coal problems, appear to have only a vague idea of the components of coal and their origin. Some are even in doubt as to whether substances derived from the wood and resins of plants form a part of coal; and few seem to have more than the dimmest idea of what are the components of coal, the condition in which these now exist, and the transformations that they haye undergone. Although during the paiilt century or more many co.rrect observations have been made and recorded, these were falsely or inadequately interpreted, so that many of the interpretations rendered are contradictory. As a result there has been great confusion. Many of the observations made in the past, although accurate and correct, could not be explained, because the principles involved in a correct solution of the problem were not then known. For example, Parkinson, Hutton, Petzhold, Guembel, and others made valuable discoveries regarding the processes by which plant substances are transformed into coal, but as the principles involved are those of colloidal chemistry, a science not known to the scientific world of that time, the observed facts could not be interpreted and the solution of the whole problem was blocked. The explanation of the true meaning of the alternating bright and dull bands so familiar in all ordinary bituminous coals afforCls another example. This banding has been observed and recorded from the earliest times, and has led to the forming of many false theories. Some gAologists, for example, have endeavored to explain the bands as due to alternating climatic conditions during the coal-forming period. Had the geologists known the true nature of coal they could not have made this mistake nor many others made in the past. To fill in a few of these gaps and to clarify some of the existing confusion is the aim of this paper. The immediate cause that led the author to investigate further the composition of coal and the origin and structure of its constituents was that when an attempt was made to discover the meaning of the coking and noncoking properties of coal a more exact knowledge of the nature of coal was required than was then available.

Jan 1, 1920