Search Documents

By Paul G. Swanson

This manual of practice is to be used in combination with the final reports for the study of spoil stability in the Eastern Coal Province. The manual applies the predictive matrices developed in the parent study for use in evaluating the stability of typical mine spoil slopes. The values of internal friction and pore pressure coefficient are derived for many varied slope conditions. The results can be used in conventional stability analysis equations to assist the mine operator or regulatory personnel in evaluating spoil stability from very limited information.

Jan 1, 1983

By Lawrence K. Requa

The property being worked by the Lewiston dredge of Placer Development (Ltd.) is on the Trinity River in Trinity County, Calif., about 9 miles north of the town of Lewiston (see fig. 1). The nearest rail point is at Rending, Calif., which is exactly 50 miles bar road from the dredge camp. Recently a very good section of State highway has been constructed from Redding to Weaverville, and it is now possible to use this highway for 35 miles of the distance between the dredging property and Redding. The remaining 15 miles, however, are over ordinary dirt road. No trouble is experienced in reaching the property except for a few weeks during the middle of the winter when snowstorms may make travel difficult but not impossible. At present the property consists of about 500 acres of patented land, which extends for about 3 miles along the main Trinity River and Stuart's Pork. It is being worked with one 7-cubic foot, Bucyrus-type dredge, which has an average monthly capacity of about 100,000 cubic yards. To the end of 1931 approximately 10,000,000 cubic yards of gravel had been dredged.

Jan 1, 1932

By Edward W. Parsons

To determine in what part and to what extent creep or movement exists in an installed rock-bolt anchor and the effect of the creep or bleedoff on the tension load on a rock bolt, as well as the effect of normal mining activity on the rock-bolt load and anchor, the Bureau of Mines conducted tests in the laboratory and in two mines using four types of expansion-shell anchors, the wedge bolt, and in one mine, explosive-anchored rock bolts. Specially mounted heavy-duty springs, calibrated to obtain load readings from spring movement, were installed on the test bolts to prevent a drastic reduction in tension load caused by slipping or seating of the anchor. A dial gage, reading to 0.0001 inch, measured movement of the anchor shell against the rock and seating of the anchor wedge plug in the shell. While all bolts had electrical resistance strain gages for load reading, only readings from the laboratory tests were used because those from the field tests were erratic. The tests revealed that most load loss resulting from static loading is due to the slippage and seating of the serrations on the anchor shell into the drill-hole wall. Dynamic loading, primarily from sudden shocks from nearby blasting, and possibly from ground movement or mining activity, will cause the anchor wedge plug to seat in the anchor shell.

Jan 1, 1969

By Albert L. Toenges

The production of coal from underground mines in Washington declined during the recent war owing to shortage of manpower, and coal was shipped to the Pacific Northwest from mines in the Rocky Mountain region. The movement of this coal into Washington required the use of railroad equipment that otherwise could have been used for transporting war materiel and personnel. Strip mining uses a minimum of manpower, and the development of coal areas in the Pacific Northwest that can be mined by the strip method should increase production in the area, thus releasing railroad equipment from the necessity of transporting coal long distances and also providing consumers with a lower-cost product. The development of a strip mine to supply the demand at low cost requires a large investment in heavy equipment. In order that the fixed charges due to large investment in plant and equipment may be kept at a minimum, large reserves of coal must be proved. A reconnaissance of an area near Toledo, Lewis County, Wash., indicated a large bed of lignite that could be mined by strip methods. The area is approximately midway between Portland, Oreg., and Tacoma, Wash. (refer to fig. 1), and the opening of a large mine in the area would supply fuel to these and other nearby centers.

Jan 1, 1947

By L. A. Morley

This report summarizes the work performed on Bureau of Mines Contract J0199106, "Portable Trailing Cables, Splices, and Couplers - Design and Installation Considerations," from May 1, 1979 until December 31, 1981. Splice installations and considerations for the possible use of conductive-rubber shielding in low-voltage trailing cables as well as coupler installations in high-voltage cables were the principal tasks. Flammability measurements on cable components and general testing facilities for mine electrical equipment were secondary tasks. Theoretical and empirical data indicate that conductive rubber with high resistivity values is an unsatisfactory shield design for current-sensing fault detection. Elimination of partial discharge in coupler installations requires meticulous care.

Jan 1, 1982

By George L. Gates

It is generally recognized that if the lose and contamination of the fluid content of a core specimen from an oil- and gas-bearing formation in a well were eliminated, the value of core analysis would be increased greatly. In an effort to obtain uncontaminated cores, extensive field tests were carried out in the Mercy field, San Jacinto County, Tex., with the Carter pressure core barrel and an oil-base drilling fluid having very low rates of filtration as measured by the standard A.P.I. drilling-fluid filter teat. A tracer was added to the drilling fluid filter test. A tracer was added to the drilling fluid to provide a means for quantitatively measuring the volume of oil filtrate in the cores. Unfortunately, as stated in the report on the Mercy tests, very little oil nand was penetrated in coring the well; and because the performance of the pressure core barrel was not entirely satisfactory, the tests did not provide a complete answer to the question: Does a filtrate from an oil-base drilling fluid enter cores., and how does it affect the results of the core analyses?

Jan 1, 1950

Although not immune from the problems affecting the U.S. economy generally, the mineral industry in 1991 contributed nearly $300 billion in the value of processed materials of mineral origin. Supporting this contribution, the Bureau of Mines continued the research and analytical programs highlighted in this annual review. Featured in 1991 were such relatively new programs as minewide monitoring applications in ground control and advances in processing of ceramics and composites, along with more traditional research into health, safety, and mining technology, minerals and materials science, and environmental technology. Under Bureau sponsorship, a National Minerals Policy Forum brought together some 200 executives from industry and Government concerned with minerals policy to begin a dialogue on developipng a policy statement on current minerals issues. A major feature of the forum was the keynote address by Secretary of the Interior Manuel Lujan, Jr.

Jan 1, 1992

By A. C. Johnson, es Hol, E. O. Binyon

"INTRODUCTION AND SUMMARYThe tungsten properties of Lincoln Mines, Inc., and North Tem Flute Mining and Development Co. were first explored by the Bureau of Mines in 1942. Work on the project comprised trenching, sampling, a small amount of road and trail construction, and a small amount of core drilling. From April 13 to December 10, 1944, additional diamond drilling was done by the Bureau of Mines to test the lateral and downward extensions of the various tactite zones along the contact south of the Lincoln mine, including the property of the North Tem Piute Mining & Development Co.Claims leased by the Lincoln Mines, Inc., are in secs. 25 and 36, T. 3 S., R. 56 E.; secs. 30 and 31, T. 3 S., R. 57 E.: and sec. 1, T. 4 S., R 56 E., M. D. B. & M., in the Tem Piute Mining District, near the north end of the Timpahute Range in west central Lincoln County, Nev. D. B. Fegles is president of Lincoln Mines, Inc. and general offices are in the Wesley Temple Building, Minneapolis, Minn.In June 1945, the Atolia Mining Co. leased the property and purchased the mill and mining equipment from Lincoln Mines, Inc. P. R. Bradley is president of the Atolia Mining Co., whose offices are in the Crocker Building, San Francisco, Calif. This company surrendered the lease on the property on September 30, 1948. The property owners are continuing operations and are now engaged in building a 20-ton mill.The claims of the North Tern Flute Mining & Development Cc. are in sec. 1, T. 4 S., R. 56 E., M. D. B. & M. Merle F. Schofield is president of the company and maintains an office at Hike, Nev. These claims were leased by H. P. Laslett, of the Utah Nevada Mining Co., in 1945 and by the Atolia Mining Co. in 1946. The owners are now doing some exploratory work."

Jan 1, 1950

By H. R. Shell

The work on synthetic mica and related subjects is being reported in a series of technical articles (see Supplementary Bibliography), each of which describes some special aspect of the subject. This is the final report on chemical analysis of the fluoride-containing silicates. A condensation of this report has been published (26).3/ Chemical analysis affords one of the best means of ascertaining the final com-position of either a heterogeneous mass or a single pure crystal, particularly where some constituents may be volatile. The analysis of fluoride-containing silicates was not so well known or understood that highly accurate results were commonplace. For example, on synthetic mica a university laboratory reported 11.6 and 9.2 percent fluoride when at least 13.3 and 11.3 percent were present, respectively; a commercial testing laboratory reported 9.14 percent as compared to 12.6 percent; and a glass company reported 7.0 percent as compared to 9.0 percent present. No intimation is made that these analysts could not have done better, but the point to be stressed is that the methods in use were long, tedious, and generally required a certain familiarity for best results.

Jan 1, 1956

By C. A. Komar

The Bureau of Mines is investigating possible applications of acoustic energy at sonic and ultrasonic frequencies in petroleum production. A phase of this work involves measuring sound velocity through petroleum reservoir rocks. References and abstracts were prepared as a bibliography to make available to others some of the material obtained from a literature search covering the past applications and the present uses of sound. Laboratory and theoretical studies of the various parameters that influence the velocity of sound in porous media account for the wealth of information now available. Velocity of propagation of sound waves in porous sediments as a function of depth is a quantity frequently measured. Velocity logging systems, capable of measuring speed of sound waves in underground formations penetrated by wells, have been developed for interpretative studies. The close relation between acoustic velocity and porosity makes it possible to determine porosity from velocity logs. Most velocity log interpretation in terms of porosity is based on a formula developed by Wyllie and others known as the time-average relation.

Jan 1, 1963

By Erik Bengtsson

Phenol was discovered in coal tar by Runge (1)1/ in 1834 and was isolated (2) in 1841 as pure phenol by distilling the tar, extracting with caustic soda, acidifying the extract, and fractionating the tar acids. Later, o-cresol was isolated (3) through careful fractional distillation of the tar-acid mixture. The m-and p-cresols distilled within a boiling range of about 1.50 c. and had to be separated by other means. Raschig (4) fractionated the tar-acid mixture to obtain pure o-cresol, sulfonated the mixture of m-and p-cresols, and treated the cresol-sulfonic acids with superheated steam at 1200 to 1300 c. to hydrolyze the m-cresol sulfonic acid, the p-isomer was not affected at that temperature. He also attempted to make use of the different crystallizabilities of the m-and p-cresol sulfonic acids (5). When treated with sodium bisulfate and sodium pyro-sulfate at 100° to 110° C. or with sulfuric acid (90/0) at 20° C., only the m-cresol was sulfonated (6). Hoffman-La Roche (7) treated the meta-para mixture with concentrated sulfuric acid at 40° to 100° C., when m-cresol and part of the p-cresol was sulfonated, and precipitated the m-cresol sulfonic add by diluting with water. The same sort of separation may be carried out by means of 80 percent sulfuric acid at 35° C. and 35 mm pressure (8).

Jan 1, 1950

By G. S. Scott

The investigation of the causes, behavior, and control of anthracite mine fires, which the Bureau of Mines has been carrying on has yielded several publications directly applicable to mine-fire problems. 3/, 4/, 5/, 6/, 7/, 8/ As a further step in elucidating the causes of heating in certain anthracites subjected to oxidation, reliable information vial needed relative to the actual amount of heat that is liberated when a unit volume of oxygen combines with anthracite at varying temperatures.

Jan 1, 1939

By A. S. Swanson

The Babb fault vein in Crittenden and Livingston Counties, Ky. (fig. 1), is one of an extensive series of such veins in the Western Kentucky and Southern Illinois fluorspar district. First operated in 1904, the production to May 1, 1944, was estimated at 143,000 tons of fluorite ore. There are five mines (fig. 2) on the Babb fault zone - Guill ,Kentucky Babb, Delhi-Babb, Eagle-Babb and Howard-Barnes. The Bureau of Mines developed four of these properties by core drilling from July 9, 1943, to May 1, 1944. During that period a total of 8,177.8 feet of diamond drilling was completed in 28 holes.

Jan 1, 1950

By G. L. Neumann

The Guymard mine in Orange County, N. Y., is reported to have been discovered in 1862 and mined until 1876, producing 10,000 tons of lead and zinc ore. The property was examined by an engineer of the Bureau of Mines in 1948. Development work was done by the Bureau in April and May 1949 and March 1950. During these two periods four drill holes totaling 2,090 feet were completed. The mineralized sections of the core were sampled and assayed.

Jan 1, 1952

By Thomas R. Bur

The strain and pressure gage methods for evaluating the relative performance of explosives in rock were compared. This comparison was based on a study of the responses of strain and pressure gages to explosion-generated seismic waves. Several explosives) representing a wide range of detonation pressures) were used. In general the relative performance of these explosives) as determined from amplitude) impulse parameter) and energy parameter measurements) is the same if the compressive portion of the strain pulse and the comparable portion of the pressure pulse are considered. Other similarities and differences of the two methods are also discussed.

Jan 1, 1967

By D. P. Schlick

The German experience in dealing with the health hazard of respirable dust in underground mines is reported from first-hand observation in this Bureau of Mines paper. The report covers-- 1. The control of dust by water infusion, water spraying, and ventilation. 2. The sampling devices (tyndalloscope , konimeter , and BAT-I) and methods used to determine the dust concentrations in mines. 3. The systems of classifying hazardous and safe dust levels in mines. 4. The research facilities devoted to theoretical and applied work on mine dust and pneumoconiotic disease. Tile major research projects on dust and disease now underway in West Germany are outlined in an appendix.

Jan 1, 1970

By J. G. Kirby

According to the Bureau of Mines annual survey, as of January 1, 1954 there were 337 refineries with a total daily crude-oil throughput capacity of 8,006,897 barrels. The total daily capacity increased 368,236 barrels during the year while the total number of refineries declined 6. The capacity of the average refinery to process crude oil therefore increased during 1953 from 22,270 barrels to 23,759. With the exception of the Texas Inland, all refining districts reported gains in the installed capacity for the year, the largest being the Louisiana Gulf Coast with an increase of 20 percent. A total of 397,500 barrels of additional crude oil capacity was reported as under construction January 1, 1954. Accounting for 129,500 barrels of this total are facilities for 3 new refineries in North Dakota, 2 in Washington and I each in Ohio and Utah. Equipment being installed to replace existing units, totaled 180,750 barrels daily.

Jan 1, 1954

By D. Montagna

This Bureau of Mines report describes a salt-free, fluxless method for reclaiming metallic aluminum from aluminum dross. The dross is smelted under argon, nitrogen, or carbon dioxide, instead of a salt flux, in an externally heated pot furnace. Aluminum recovery, using argon, is equal to recoveries reported from commercial smelters that process dross in rotary-type furnaces This salt-free method could offer a reduction in air pollution, lower energy requirements by elimination of salts, and the production of up to 60 percent less solid waste for disposal than the salt method.

Jan 1, 1978

By Edward D. Thimons

As U.S. mines go to greater depths, the high temperatures and humidities characteristic of such depths make it difficult to maintain a comfortable environment in working areas. Better techniques for cooling these deep working areas are needed. At the Homestake gold mine in South Dakota the Bureau of Mines has tested a water spray cooler inserted into the fresh air vent tube entering a warm stope. The cooler supplied more than 6 tons of refrigeration to the stope air, which dropped from an inlet temperature of 83° F dry bulb and 75° F wet bulb to 73.5° F dry bulb and 71.5° F wet bulb. These preliminary results show the water spray cooler to be a feasible concept. However, there is a need for substantial refinement and further testing, and work on the concept will be continued under contract to the Bureau.

Jan 1, 1979

By Graham W. Marks

This report is the fourth of a series concerning the development of spectrochemical methods for the analysis of ore samples and related Metallurgical materials by the total-energy method. In this report, the application of this method to the determination of thallium is discussed. This element lies in group III of the periodic tale; one other Clement of this group; indium, has already been investigated.

Jan 1, 1949