Search Documents

By G. R. Hopkins

For several years prior to about the middle of 1928 both the number and capacity of natural-gasoline plants showed a steady increase; this resulted from a material gain in the supply of casinghead has due to the discovery of a number of flush fields with relatively high gas-oil ratios. From 1928 to date some form of proration has been continually in force, with a consequent curtailment in the supply of wet gas. This decline in available gas and a severe decrease in prices, due largely to the increasing competition of light refinery products, has eliminated virtually all of the weaker units during the last 5 years, with the result that the number of plants declined from 1,155 on January 1, 1928 to 19035 on January 1, 1930, to 909 on January 1, 1932, and then to 859 on January 1, 1934, The struggle of the small high-cost producers to exist is illustrated further by the trend in the number of shut-down plants, which has increased from 36 on January 1, 1930 to 100 on January 1, 1932 and to 128 on January 1, 1934. The increase in the number of plants prior to 1929 resulted in a material gain in the total capacity, but the decline in number between 1929 and 1932 was not followed by a corresponding decrease in capacity, as gains resulting from the construction of a few very large plants overbalanced the loss due to the dismantling of a large number of small ones. However, the low prices of 1932 and 1933 supplied little incentive for new construction, and the total capacity declined in approximately the same ratio as the number. Thus the total capacity declined from 11,387,000 gallons daily on January 1, 1932 to 13,060,000 gallons daily on January 1, 1934, Of the latter 9,181,000 gallons (91 percent) represented the capacity of the operating plants and 679,000 gallons (9 percent) the capacity of the idle plants.

Jan 1, 1934

By Chas. G. Maier

The absence of plants on the Pacific coast for the reduction of iron ores usually is attributed to the fuel situation there. Thus, the bulletin of the. State Division of Mines for 1933, entitled "California Mineral Production," says: "There are considerable deposits of iron ore known in California, notably in Shasta, Mad era, Placer, Riverside, San Bernardino, and Los Angeles Counties, but production has so far been limited for lack of an economic supply of coking coal." It has been estimated that the six major steel plants of the Pacific coast have an annual ingot capacity of 600,000 tons. The present need for tin plate averages 300,000 tons yearly for California alone, of which some 12 percent is manufactured locally. If the consump¬tion of other iron and steel products in 1929 may be taken as an approximate, estimate of the normal requirement for such products, it may be estimated further that, 65,000 to 75,000 tons each of cast-iron pipe and steel reinforcing bars and 300,000 to 400,000 tons of structural shapes and plates will be required annually in California.

Jan 1, 1936

By Fred D. Wright

The objectives of this research were: 1. to determine the stability relationships of coal mine roof rocks which are cut by fractures or intersecting joints with and without roof bolts, under various sets of conditions including horizontal formation pressures, inclination and coefficient of friction of joints, bolt loads, roof spans and rock properties; and 2. to develop criteria for the design of roof bolt sys terns for such roofs. The problem was studied by mathematical finite element models and by laboratory models. From the results of the mathematical and laboratory models, equations were derived to express the relationships listed above for cracked, single-layered roof beams and design tables for such beams are included. The analysis was then extended to include multi-layered cracked beams reinforced by roof bolts and a method for analyzing and designing bolting patterns for such roof rocks is presented.

Jan 1, 1974

By E. A. Pelczarski

Initially, the objective of this contract was to develop a PWSCSR that could meet proposed criteria (that were different from 30 CFR 11(Title 30 of the Code of Federal Regulation part II) and that would be less than twice the size and weight of a filter self rescuer. This objective was met. Consequently, the original contract was extended to develop a PWSCSR that would meet existing CFR-30 criteria within the same size and weight constraints. This resulted in the development of a PWSCSR (the SR-100) that received NIOSH/MSHA approval (TC-239). This report presents a historical discussion of the design and development of the SR-100 as developed by CSE Corporation under Bureau of Mines contract number H0368013. The technical parameters and the test results of NIOSH/MSHA 30 CFR 11 certification are also presented.

Jan 1, 1990

During fiscal year 1966 the Bureau of Mines published 99 scientific and technical papers and engaged in 67 research projects on petroleum, natural gas, and oil shale. A basic appropriation of $3.4 million was supplemented by $1 million in cooperative funds from other Governmental agencies and industry groups. Petroleum conservation was advanced by development of scientific knowledge and improvement of technologic methods in both the extraction and utilization of petroleum, natural gas, and oil shale. Experimental work was carried out at research centers in Bartlesville, Okla., and Laramie, Wo., and in laboratories in Morgantown, W. Va., and San Francisco, Calif. ACHIEVEMENTS IN FISCAL YEAR 1966 Bureau of Mines--Petroleum Research in fiscal year 1966 (July 1, 1965- June 30, 1966) was involved in many public issues--air pollution, peaceful uses of nuclear explosives, utilization of oil-shale resources, computerization of recovery-stimulation techniques, and fuels for supersonic airplanes. Scientific contributions included compositional studies of petroleum and oil shale, determination of thermodynamic properties of petroleum compounds, development of analytical techniques, and correlations of petroleum properties with geologic occurrence. Technologic advances included rock-fracturing research, in situ combustion studies, waterflood techniques, use of radio-tracers to study stability of petroleum fuels, and hydrogenation as a tool to prepare shale-oil products.

Jan 1, 1968

By E. S. Leaver

Experiments dealing with the dissolution of silver by cyanide from various silver minerals were reported several yews ago.4/ This work showed that the silver in some silver minerals is completely and readily soluble in cyanide solution, whereas other silver minerals must be given special treatment before or during cyanidation to obtain much dissolution of the silver by cyanide. Flotation as a method for treating silver ores has not been studied much, except in the case of base-metal ores carrying silver, particularly lead-silver ores. However, many mills now are concentrating gold ores by flotation, and when such ores also contain silver the recovery of the silver by flotation is of considerable importance. Moreover, many mines contain ore in which silver is the principal valuable constituent. Some of these ores are amenable to cyanidation, but the cost of a cyanide plant may be prohibitive because of limited ore bodies or other factors. In such instances the successful application of flotation would mean that the property could be operated.

Jan 1, 1939

The Aluminum Company of America (Alcoa) announced that the second unit at its experimental facility at Palestine, Tex. would begin production -in 1979, increasing the capacity of the facility to 30,000 tons per year. The plant uses an experimental process based on the electrolysis of aluminum chloride and reportedly uses 4 to 5 kilowatt hours per pound of aluminum produced, compared to an industry average of about 7 to 8 kilowatt hours per pound. Alcoa has reportedly signed a letter of intent with the Chinese government under which Alcoa will conduct feasibility studies on two new integrated aluminum projects and modernization of an existing aluminum plant. If the study results are favorable, Alcoa Engineers Inc. and the Import and Export Company of the Chinese Ministry of Metallurgical Industry could negotiate agreements to provide Alcoa technology and services for the projects.

Jan 1, 1979

The Bureau of Mines has been active in promoting the purchase of coal for Government use under specifications that define the requirements in terms of heating value of the coal, expressed in British thermal units, and the composition as shown by proximate analyses. To these, when required, are added the ash-softening temperature, the free-swelling index, and the Hardgrove grindability index. Under most of these specification contracts the bidders guarantee the quality of the coal, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled in accordance with instructions2 issued by the Bureau of Mines; the samples are analyzed in the Bureau laboratory to determine whether the coal is of the quality guaranteed by the contractor; if it is not, a price adjustment is made, Analyses of the delivered coal and tipple samples (samples collected at mine tipples as coal is being loaded into railroad cars or trucks) provide valuable data for use in evaluating future bids. In addition, the continuous sampling of coal as delivered is a check on the practical results obtained in burning the coal.

Jan 1, 1971

By Arno C. Fieldner

The objectives of the coal-research activities of the Bureau of Mines are very well expressed in the organic act of Congress establishing the Bureau. It reads as follows: That it shall be the province and duty of the Bureau of Mines, subject to the approval of the Secretary of the Interior, to conduct inquiries and scientific and technologic investigations concerning mining, and the preparation, treatment and utilization of mineral substances with a view to improving health conditions, and increasing safety, efficiency, economic development, and conserving resources, through the prevention of waste in the mining, quarrying, metallurgical and other mineral industries; to investigate explosives and peat; and on behalf of the Government to investigate the mineral fuels and unfinished mineral products belonging to, or for the use of, the United States, with a view to their more efficient mining, preparation, treatment, and use; and to disseminate information concerning these subjects in such a manner as will best carry out the purposes of this act.

Jan 1, 1946

By J. W. Jensen

EXTENSIVE research and development was performed on the manganese-copper vibration-damping alloys to determine the relationship between the properties of the alloys and variations in composition, fabrication, Mid heat treatment. Mn-Cu alloys with unusually high specific damping capacity, 20 to 25 percent at a stress of 5,000 psi, have also the following useful properties: Tensile strength, 90,000 to 110,000 psi; yield strong, 60,000 to psi; elongation, 20 to 25 percent; hardness, 90 Rockwell B; and fatigue limit at, 28,000 to 30,000 psi. Both standard and special methods of testing were employed to obtain data on strength, modulus, hardness, resistivity, dilatation, micro-structure, crystal lattice, and damping capacity. The extensive tabular and graphical data on these properties are presented for alloys containing 50 to 85 percent as quenched d solution) and after various aging treatments. Expansion coefficients for all Mn-Cu solid solutions are graphed and a dilatometer study of contraction during aging is reported. Although high damping capacity is associated with aging to precipitate a-Mn from solid solution, with a cubic-tetragonal transformation and with the occurrence of antiferromagnetic ordering in Mn-Cu alloys, a tenable theory of the damping mechanism has not been reached.

Jan 1, 1965

By E. S. Leaver

Experiments dealing with the dissolution of silver by cyanide from various silver minerals-were reported, several years ago.4/ This work showed that the silver in some silver minerals is completely and readily soluble in cyanide solution, whereas other silver minerals must be given special treatment before or during cyanidation to obtain much dissolution of the silver by cyanide. Flotation as a method for treating silver ores has not been studied much, except in the case of base-metal ores carrying silver, Particularly lead-silver ores. However, many mills now are concentrating gold ores by flotation, and when such ores also contain silver the recovery of the silver by flotation is of considerable importance. Moreover, many mines contain ore in which silver is the principal valuable constituent. Some of these ores are amenable to cyanidation, but the cost of a cyanide plant may be prohibitive because of limited ore bodies or other factors. In such instances the successful application of flotation would mean that the property could be operated.

Jan 1, 1939

By Robert N. Roby

"The Moffet-Johnston property was investigated by the Bureau of Mines with the object of determining the presence of ore reserves that might be utilized during the war emergency. Preliminary examination was made during May and Juno 1943, as a result of which the Johnston 'tunnel was cleaned out and repaired, the .mime was surveyed, and a small program of exploration was undertaken. This report describes the work performed and presents the data obtained.In its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts prelimi¬nary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples and performs benefication tests. Both these branches are under the supervision of Dr. R. S. Dean, assistant director.The chemical and spectrographic analyses were made at Reno, Nov., under the direction of A. C. Rico, acting engineer in charge, Rare and Precious Metals Experiment Station, Bureau of Mines. The ore-dressing tests were under the direction of Rollien R. Wells, metallurgist, at the Salt Lake City laboratories of the Bureau of Mines.The author acknowledges the cooperation and assistance of the lessee of the property, H.R. Hakes, who furnished nine reports and other information.The Moffet-Johnston property is in secs. 2 and 3, T. 3 S., R. 5 W., in the Tidal Wave mining district of Madison County, Montana.The portal of the Johnston adit is near the mouth of Bear Gulch, 9 miles northeast of Twin Bridges, Mont. It is reached by an improved dirt road that serves mining properties farther up Bear Gulch. The Moffet mine and the Mountain View shaft are now accessible from the Bear Gulch road over an access road recently completed by the U. S. Grazing Service. The Grazing Service road has also been supplemented by bulldozer trails built by the Bureau of Mines.An electric-power line extends from the Montana Power Co's substation at Twin Bridges to mines at the head of Bear Gulch and passes within 200 feet of the Johnston portal.The claims of the Moffet-Johnston property were located about 1900. A report by H. V. Winchel, consulting geologist, in 1904 indicates that most of the development on the Johnston adit was completed by that date. At the time of the Winchel report, the Moffet workings had just penetrated the first ore shoot (fig. 4)."

Sep 1, 1946

[In selecting deposits of exploration projects, tabular deposits or large mineralized masses are favored because they may be explored systematically and because they afford the best opportunity for blocking out reserves in advance of mining, whereas irregular, small pipes and scattered]

Jan 1, 1941

By Irving Wender

The oxo reaction consists of catalytic conversion of olefins by reacting the olefins with CO and H2 (water gas) to aldehydes that contain one more carbon atom than the starting olefin. The aldehydes are then generally reduced with hydrogen to primary alcohols in a second stage. The two-stage process is called the oxo process. The word "oxo" is derived from the German "oxierung" (ketonization); thus the exact English equivalent of "oxo" is "keto". The oxo process may be applied to nearly all olefins. A wide range of pressures and temperatures may be used in both stages. The pressure range usually employed is 150 to 200 atmosheres. The temperature in the first stage is usually about 140° C. and in the second or hydrogenation stage about 180° C. Although a standard Fischer-Tropsch catalyst may be used for both steps, cheaper catalysts have been utilized to effect hydrogenation of the aldehydes. Most of the information for this, report on the oxo process was gathered from Technical Oil Mission microfilms. T.O.M. Reels 14, 55, and 134 were especially valuable. T.O.M. Report 6 by H. M. Weir was very helpful. Information on the oxo process is scattered throughout documents captured in enemy territory, and the present report does not include all the available data. Some of the information was procured by personal interview. Where, in the body of this report, certain investigators are quoted, the source of the statement is either personal interview or the T.O.M. reports.

Jan 1, 1948

By C. H. Riggs

This petroleum-engineering report of the Atlanta oil field in BO them Arkansas reviews reservoir conditions and pressure-production history of one of the important Smackover limestone fields in southern Arkansas. The study of the field was made and the report prepared to aid operators in this and similar fields to increase the efficiency of recovery through the application of better engineering practices. A similar study of the Magnolia field in Arkansas by Carpenter and Schroeder was the first of these reports prepared under a joint agreement between the Arkansas Oil and Can Commission and the Bureau of Mines. The increasing demands for petroleum and its products and the steadily increasing cost of discovering and developing oil field; emphasize the importance of conserving known reserves of oil and gas. In recent years vast improvements have been made in the technique of oil recovery, both by better utilization of the natural energy stored in the reservoir and by improved methods of applying external energy to the reservoir system. This report may aid in oil conservation by careful evaluation of the several factors that did or did not contribute the greater recovery in the Atlanta field and by suggesting improvements in production methods and applications.

Jan 1, 1949

By Paul M. Tyler

In 1939, American industry got, off to a poor start, slowed down further during the first quarter, quickened after May, speeded up still more when war broke out again in Europe, and ended the year at a pace close to an all-time record. The average index of general business activity for the entire year (105) was well ahead of that for 1938 (86), failed to equal that of 1937 (110), and fell behind the average for 1929 (119) by a wide margin. (Federal Reserve Bank yearly indexes in parentheses).

Jan 1, 1940

By Guy E. Dent, Hugo E. Kuehn

"SUMMARYFor making a comparison of magnetic surveys measured from the ground and from the air, Worcester County, Maryland, was chosen as a proving ground. Vertical magnetic intensities were observed on the ground, and total magnetic intensities were observed from the air. A comparison of the two magnetic maps reveals similar large magnetic features, but these are displaced in some instances by distances greater than a mile. Magnetic terrane in the two charts is of the same type but often differs greatly in respective characteristic features.The sacrifices in accuracy that may be expected from the use of different systems of diurnal magnetic corrections on ground observations constitute a part of this report.INTRODUCTIONThe value of magnetic surveys for gaining information concerning the crystalline basement is recognized increasingly. That this topography is often reflected to a major degree in the overlying sediments with certain offsetting is well understood. Even where such sediments are deep, the surface topography of upper formations often reflects this bedrock topography to a certain degree."

May 1, 1947

By C. J. Wilhelm, John M. Devine, Ludwig Schmidt

"Steel tanks often corrode rapidly in oil fields where the Gas produced with crude contains an appreciable quantity of hydrogen sulphide. In many instances working tanks have been discarded after only six months of service because of failure induced by corrosion.Aluminum has been used for some time in the fabrication of certain equipment incidental to the handling of oils containing hydrogen sulphide gas in solution, and has exhibited no carious corrosive action. These uses indicated that aluminum tanks,be equally effective in counter- acting hydrogen sulphide corrosion. Consequently, in the spring of 1920, an all-aluminum stock tank of 500 barrels capacity and a ""composite"" tank of equal capacity, having a steel bottom and bottom ring and an aluminum top and top ring, were placed in service on the State-Lassiter lease of the Gulf Production Co, in Crane County, Tex. These tanks were under observation for one year, the toot being sponsored by the Gulf Production Co., the Aluminum Co. of America, and the Parkersburg Rig and Reel Co. The results of this preliminary test sustained the belief that aluminum is highly resistance to hydrogen sulphide gas and likewise indicated the type or grade of aluminum which could be most economically used for lease tankage. However, in this preliminary test the tanks were not subjected to contact with the quantities o highly concentrated brines such as often are associated and produced with crude oil. Therefore, it was suggested by representatives of the aluminum Co. that additional tests be made to include production conditions in large quantities of brine would be handled, for pact experience had shown that aluminum often is susceptible to the corrosive action of brines."

Apr 1, 1931

[In selecting deposits for exploration projects, tabular deposits or large mineralized masses are favored because they may be explored systematically and because they afford the best opportunity for blocking out reserves in advance of mining whereas irregular, small pipes and scattered]

Jan 1, 1941

By Lewis C. Karrick

Although the Bureau of Mines has thus far made no large-scale experiments with oil shales, and the feasibility of the commercial manufacture of shale-oil products suited to present market requirements has not been demonstrated, there is ample reason to believe that these products will eventually supplement the more commonly used petroleum products and give equally good service. In 1919 the bureau, in cooperation with the Department of Metallurgical Research, University of Utah, began investigating the oil shales of the United States to obtain detailed information on their value. The States of Colorado and Indiana also cooperated through their State universities, in which research laboratories were organized to assist in carrying on the oil-shale studies planned and directed by the bureau. As a result of these studies much information is now available concerning laboratory methods of producing the greatest yields of the best products from oil shale. In order to study the principles that govern the retorting of oil shales and to test the oils produced, it has been necessary to develop and standardize reliable apparatus and methods for distilling shale, and to adapt to the testing of shale oils some of the methods the Bureau of Mines uses for testing petroleum. The methods employed by the Scottish shale-oil manufacturers were also studied, but most of them have been superseded by those described in this bulletin, which give more comprehensive and accurate results and employ more convenient apparatus. This paper is presented, therefore, as a manual of apparatus and methods that the bureau has developed for work on oil shale and found satisfactory for routine tests and for research. Explanation and discussion of the principles underlying the methods of testing are included wherever necessary for a clearer understanding.

Jan 1, 1926