Search Documents

By Daryl R. Tweeton

The Bureau of Mines conducted experiments to measure the influence of environment on the friction and wear of a steel-quartz system at several speeds and loads. In each test a quartz block was pressed against a rotating ring of low-carbon steel. Environments used were moist air, dry air, dry nitrogen, water, aqueous oleylarnmonium acetate (ClsH35NH3+-OCOCH3), and aqueous aluminum chloride (A1C13). The sliding speeds were 2.2, 13, and 33, cm/sec, and the loads were 6.8 and 13.6 kg. The coefficient of friction, the wear, and the roughness of the surfaces were measured, and the wear debris was examined. The coefficient of friction was significantly lower in moist air at 2.2 cm/sec than for any other combination of environment and speed employed, and was generally an inverse function of the oxidizing ability of the environment. The coefficient of friction increased somewhat with increasing load. The wear of the steel rings was greatest in dry air at all speeds and loads. The wear of the quartz blocks at 180 rpm was greatest in dry air, but at 12 rpm it was greatest in nitrogen. Friction and wear in aqueous oleylarnmonium acetate and in aqueous aluminum chloride were similar to effect in water alone.

Jan 1, 1976

By F. S. Kendorski

This report covers the work on developing criteria for determining when a hazard exists when mining stratified mineral deposits beneath bodies of surface water. The nature of water bodies is considered, the disturbance to the strata induced by mining is described, inundation case histories reviewed, reasonable water inflows derived, and methods of mining to prevent or minimize the hazard are presented. Criteria are given whereby effected industries and agencies can recognize a potential hazard and plan a mine accordingly, releasing considerable mineral reserves otherwise considered unminable.

Jan 1, 1979

By F. L. Wideman

This report describes a computer program that is used for the calculation of the coordinates and elevations of subsidence survey pins located by intersection. This program was developed for the Federal Bureau of Mines by the Numerical Analysis Laboratory, University of Arizona. These calculations, although relatively simple, are both tedious and time-consuming when computed with a desk calculator and trigonometric tables. In this survey, a large number of pins were surveyed repeatedly, and it was evident that both time and money could be saved by using a digital computer.

Jan 1, 1962

By Steven J. Schatzel, Gerrit V. R. Goodman, Robert B. Krog, C. Özgen Karacan, Gabriel S. Esterhuizen

Although longwall mining productivity can far exceed that of room-and-pillar mining, the total methane emissions per extracted volume associated with longwall sections are generally higher than those for continuous miner or pillar removal sections. Increased face advance rates, increased productivities, increased panel sizes, and more extensive gate road developments have challenged existing designs for controlling methane on longwalls. Methane control research by the National Institute for Occupational Safety and Health (NIOSH) recently examined a number of practices designed to maintain concentrations in mine air within statutory limits and consistently below the lower explosive limit. These included a reservoir modeling approach to predict methane inflows in gate road entries. The outputs sug­gested that emission rates in the gate roads decreased with the use of shielding boreholes and increased degasification time. Also, mining perpendicular to the face cleats liberated more gas into the mine workings, emissions were almost a linear function of Langmuir pressure and volume, and emissions were inversely related to sorption time constant. Subsequent simulations predicted changes in methane drainage using in-seam boreholes. The results showed that longer degasification times resulted in lower face emission rates. Premining degasification produced more methane than that produced during panel extraction, a fact attributed to the already decreased methane content of the coalbed. This work concluded that longer premining degasification periods would be more advantageous to the operator. The industry trend toward increasing longwall face width can produce increased methane emissions from the face due to a higher volume of cut coal on the face conveyor. Two methods were used to estimate face methane levels on longer faces. In the first method, segmented methane data were extrapolated for greater face widths. The second method estimated emissions contributions from the shearer, face conveyor, panel belt, longwall face, and ribs, and summed these for wider panels. Permeability changes in the gob behind the longwall shields were estimated using a NIOSH-developed numerical model. The results showed that permeability was highest near the edges and corners of the gob.

Jan 3, 2008

By M. C. Malamphy

A general description of the activities and results of bauxite investigation by The Bureau of Mines at its bauxite project in Saline and Pulaski Counties, Ark., has been given in Report of Investigations No. 4251. The factual data obtained during the project are reported in a series of Reports of Investigation beginning with No. 4251, of which this is the fourth. The data are accompanied by maps showing the location of holes drilled and the deposits developed. Each area upon which work was done is reported by half townships. Each bauxite deposit investigated was assigned a name and a number for ready reference and identification, and its location and name are shown on the appropriate half-township map. The description of each half township is followed by a description of each deposit developed in that half township. The 14 half-township maps and 77 detail maps of the bauxite deposits in this series of reports give the locations and numbers of all the holes drilled on the project except the deep holes drilled to test the geophysical anomalies. The locations of those holes show on Figure 13 in Volume 1. The descriptions of the deposits developed are followed by complete detailed logs of the drill holes. Many of the widely spaced exploratory holes did not discover bauxite of minable thickness and grade. The pertinent information obtained from the widely spaced exploratory drill holes has been summarized and tabulated, and a table for each half township-is given with the discussion covering that area.

Jan 1, 1948

By James V. Kelly

"INTRODUCTION In the course of Bureau of Mines investigations of iron ores near Scappoose, Columbia County, Oreg. during 1942, occurrences of laterite were noted in road cuts and outcrops at many localities in the county. In 1944, the State of Oregon Department of Geology and Mineral Industries completed a preliminary examination of alumina-iron-bearing laterite occurrences in Washington County north of Hillsboro, Oreg.3/ Their report suggested that the lateritic material might be amenable to treatment by the Pederson process for the commercial production of iron and alumina. In order to determine the extent and character of some of the reported lateritic occurrences, the Bureau conducted preliminary explorations in Columbia County near St. Helens, Oreg., from January through June 1945. Almost simultaneously the Alcoa Mining Co. began to explore nearby areas. Their work was continued and expanded after the Bureau's work had been discontinued. This report presents the data obtained from the exploratory work of the Bureau of Mines.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral re¬sources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, O. C. Ralston, chief, analyzes samples and performs beneficiation tests.Samples were assayed at the Reno, Nev., laboratories of the Bureau of Mines under the supervision of A. C. Rice, acting supervising engineer, and at the Albany, Oreg., laboratories under the supervision of Dr. B. A. Rogers, chief, Albany Division, Metallurgical Branch."

May 1, 1947

By G. D. Coe

Float-and-sink tests indicate what results are obtainable by gravity separation and rare therefore an invaluable adjunct to most coal-cleaning processes. However, it is difficult to make a direct interpretation of float-and-sink data on coal, and several systems for interpreting them have been proposed. Of these, that developed and used extensively by Bird3/, Yancey4/, and Gandrud5/ is considered by the author to be the most satisfactory. It makes use of four interrelated curves (hereafter referred to as be "washability curves"). These curves were explained by Bird in a paper6/ published in 1923, but his explanation has been regarded by some as not sufficiently

Jan 1, 1938

By R. L. Beatty

IN INDUSTRIAL and domestic daily life carbon monoxide is the most frequently encountered toxic gas. hazardous concentrations of carbon monoxide may be present in the vicinity of many industrial operations, such as metallurgical processes, coke ovens, and fuel- and synthesis-gas producers, and may be encountered in confined spaces, such as dwellings, garages, workshops, vehicular tunnels, and mining operations, in connection with the use of heaters, boilers, internal-combustion engines, after blasting operations, and after fires and explosions. Evaluation and control of the health and safety hazard caused by carbon monoxide depend primarily on the analytical detection of the presence of carbon monoxide and determination of its concentration in air and in various gaseous mixtures. The choice of method of analysis in any particular situation depends on such factors as required accuracy, range of concentration involved, convenience, speed of analysis required, quantity of sample available, qualitative composition of sample or atmosphere to be analyzed, and possible effects of interfering gases. Some of the methods described require only adequate understanding of operational techniques, whereas others require thorough appreciation and skill in applying the principles involved. The instruments and analytical procedures commonly used for detecting and determining carbon monoxide are described in detail, and reference is made to more specialized methods:

Jan 1, 1955

By G. T. Krempasky

This report covers the installation and evaluation of lb reinforced concrete sets, 6 in each of 3 mines in the Goeur d'Alene mining district, Shoshone County, Idaho, and is the second of a series to determine the feasibility of a more permanent type of mine support. Closure measurements, where applicable, were made periodically of the concrete-set installations and were compared to the initial cross section of the sets. A different method of blocking was used at each test site; at one test site the type of blocking was changed several times during the test. Results from each test site are reported separately. No attempt was made to compare the cost of the concrete installations with the cost of other types of support used in the district. Such an evaluation of permanent types of support would require a longer period of time. At this time, tests are not complete enough to determine the applicability of underground concrete supports. However, results to date tend to confirm the general opinion that precast concrete mine supports could be used to advantage in openings that require support and must have long life, especially where decay of timber is an important factor.

Jan 1, 1963

By E. P. Carman

This: report gives data on the installation and operation of a packaged-unit heat-pump installation in a residence in McLean, Va., a suburb of Washington, D. C. The original equipment, installed in January 1947, was one of the first of 50 experimental Marvair units manufactured by the Muncie Gear Works, Inc., Muncie, Ind. The compressor unit of this installation was replaced by the company in September 1947, with a modified commercial model. The commercial unit and the original pump and fan accessories have been used as the sole means of heating (and cooling in summer! the. residence for the subsequent five winters and summers. The conclusions and data given herein, therefore, cover 6 winters sad 6 summers of heat pump operation, including 1 winter when temperatures averaged below normal for 2 months and the following summer when temperatures were above normal.

Jan 1, 1953

By Ray J. Holmquist

"INTRODUCTION At the request of Elmer Burch, of Taos, N. Mex., the Apache mica mine was examined by an engineer of the Bureau of Mines in October 1942. As the result of this examination, the Bureau of Mines proposed to extend an adit to the projection of the mica-bearing dike. The Federal Geological Survey then prepared a topographic and geologic map of the property. This information and consultations with members of the Survey 3/ assisted in determining the course and extent of the exploratory work. The author supervised the work, which was done from January to May 1944.Title to the property was in litigation during the period of the Bureau of Mines investigation. Conrad Johnson, of La Madera, N. Mex., was contesting the valley of Burch's claim location covering the Apache mine. Johnson was a prior claimant. A map made during mining operations prior to 1929, showing all mine workings, was in the possession of Johnson, but he would not produce it for inspection as long as his title to the property was in doubt. The course of the adit extension was therefore controlled by the best information and judgment otherwise obtainable."

Mar 1, 1947

By Lewis M. McNay

The Bureau of Hines and industry (mining and private) have studied the placement of hydraulic sandfill in deep-vein mines to identify existing problems and to develop techniques to strengthen the support characteristics of the sandfill. The hydraulic sandfill system, physical properties of typical classified mill tailings, and properties of sandfill modified by various techniques are discussed. Computer analysis has defined the support capability of various sandfills using actual mine field data as a reference base. High-modulus sandfill can provide adequate support in deep-vein mines to alleviate rock and pillar stresses and to reduce rock-burst incidence.

Jan 1, 1975

By D. Bienstock

The use of alkalized alumina in removing sulfur dioxide from a coal-combustion flue gas at 625° F was investigated on a pilot plant scale. The absorber was 26 feet long and 1.6 inches ED. Counter-current gas-solids flow at gas velocities of 8 to 15 ft/sec in the presence and absence of baffles, as well as solids entrainment at gas velocities of 20 to 23 ft/sec with solids recycle, were employed. The spent absorbent as regenerated as fixed bed with the reducing gases--reformed natural .7.7d hydrogen. Of absorption-regeneration were successful completed using the alkalized alumina rolled into spherical granules 10 to 16 mesh. There was no loss in activity of absorbent toward SO2 with a modest attrition equivalent to 0.l percent of the solids feed. Supporting studies were conducted on the effect of the sodium content in the absorbent, the composition of the reducing gas, thermal treatment to increase absorbent hardness, and removal of absorbed chlorine from the absorbent. A mathematical model was formulated to describe the removal of SO2 by alkalized aluminum from fixed and falling beds.

Jan 1, 1967

By E. H. Denny

This paper discusses accident experience and costs in 150 Colorado coal mines for the 5 years 1929-33; these mines produced 62 percent of Colorado's coal tonnage during this period. This and similar studies by the United states Bureau of Mines in other States (listed in the appendix to this report) make available comparable information on mine-accident costs and bring out clearly the importance of accident reduction from the humanitarian as well as from the economic standpoint. Compensation insurance costs constitute a considerable part of the cost of coal output. The tendency toward greater liberalization of workmen's compensation laws and increased benefits thereunder may mitigate to some extent the seriousness of an accident to a worker and his dependents, but no compensation is paid ultimately, not by an insurance fund but by the mine operator and the general public, which includes the miner. The one really effective method of reducing compensation costs is to reduce the number and severity of accidents.

Jan 1, 1935

By Jos. R. Guiteras

This is one of a series of information circulars describing mining and milling methods being published by the Bureau of Mines. The Summitville Consolidated Mines, Inc., is the only company now active at Summitville. Since the holdings of the company include those of most of the former producers of the camp, the paper virtually becomes a description of the Summitville district. The field data were collected from August 23 to 28, 1937. ACKNOWLEDGMENTS The writer gratefully acknowledges his indebtedness to H. F. Detrick, president, and Edward Thornton, general manager of the company for their cooperation in making this paper possible. Most of the information on underground operations was given by Roy Jellison, mine superintendent; the metallurgical data were supplied by Art Carl son, metallurgist, and W. L. Anderson, mill superintendent; much general and technical information was supplied by J. H. Hannan, engineer.

Jan 1, 1938

By J. H. McClain

In the last 3 years' operation of the zirconium-production plant, zirconium metal has been employed to good advantage in many applications. The most frequent use has been in situations requiring resistance to attack by hydrochloric acid. In this service, it has been shown to be a serious competitor to Hastelloy. Zirconium also has excellent resistance to most other corrosives end could be considered for use as an all purpose metal. For example, this report cites 18 applications in hydrochloric acid, 4 applications in sulfuric acid, 5 applications in phthalic-hydrochloric acid, 3 applications in wet hydrogen chloride-chlorine atmospheres, and 2 applications in fused caustic.

Jan 1, 1954

By W. W. Adams

Three hundred and twenty-eight mines and quarries, representing 36 States, took part in the twelfth yearly accident-prevention contest conducted by the United States Bureau of Mines and known as the National Safety Competition. Four underground mines and one open-cut mine (which represents the quarry and open-cut mine group), each the leader in its group, were awarded the ?Sentinels of Safety? trophy. Relative standing in the contest" was determined by the number of days lost from accidents in proportion to the total number of man-hours worked. Since 1925, when the National Safety Competition was inaugurated, an increasing interest has been taken in it by mining and quarrying companies as a means of stimulating mine and quarry safety by competition among similar plants. Each participating plant can, on a basis of its standing and record in the contest, determine to what extent its safety program is succeeding or to what extent it needs strengthening. With this information, each company that has a low standing in the contest can intensify its safety-promotion efforts the following year to obtain a lower rate and possibly win the trophy or achieve honorable mention in the competition. Except for 1929, the National Safety Competition of 1936 represented more man-hours of employment than any other year since the yearly contests began.

Jan 1, 1937

By Jr. Kauffman

The data contained in this report were obtained incidental to the Bureau of Mine's investigation of the lime-soda sinter process as applied to the recovery of alumina from siliceous bauxite, kaolin, and other high aluminous materials. The Bureau of Mines was charged by Congress to investigate processes for the production of aluminum from domestic low-grade ores. The Eastern Experiment Station at College Park, Md., conducted laboratory and pilot-plant investigations of the recover-y of alumina by the lime-soda sinter process. Reports by the College Park staff covering the recovery of alumina from these sources have been published. The lime-soda sinter process involves the sintering of the finely ground siliceous bauxite or clay with limestone and soda ash in a rotary kiln. During the sintering the alumina supposedly reacts with the soda ash to form soluble sodium aluminate and the silica combines with the lime to form the insoluble orthosilicate. In the early stages of the investigation it was considered desirable to know the temperatures at which the phase changes occurred during the sintering operation. The total time involved in the passage of any given portion of the charge through the kiln was 28 minutes. The exposure time of the charge to temperatures above 600° C. (decomposition temperature of kaolinite) was, roughly, half the total. The exposure to the full temperature of the kiln, 1,100° C was only 3 minutes. (Subsequently, the maximum kiln temperature and retention time were increased.)

Jan 1, 1949

By Jr. Flynn

This U.S. Bureau of Mines publication is a compilation of fundamental cyanide chemistry data obtained through review of the scientific literature. It includes information on thermodynamics and chemical equilibria, ultraviolet-visible and infrared spectra, and the chemistry and photochemistry of cyanide, chemical species derived from cyanide, and metal cyanide species. It also includes guidance on the use of the data for solving practical problems in precious metals applications. This publication is intended mainly for use as a reference by personnel in the precious metals industry and regulatory agencies, and other cyanide users, to provide comprehensive information on cyanide chemistry. The document should assist in the formulation of effective policies for cyanide control in the construction, operation, and closure phases of precious metals mining and metallurgical operations. In addition, the data in this publication will be useful in other contexts, such as dealing with industrial cyanide usage, cyanide-containing wastes and associated environmental problems.

Jan 1, 1995

By Milton H. Fies

The dedication of thin building, establishing a station of the U.S. Bureau of vines at the University of Alabama, bristles with significance and challenges the wisdom and courage of the people of this State. Here is united, in common aim, the Engineering School of our State University, recognized for its competency and usefulness, and the Federal Bureau of Mines. The Bureau is one of the most effective arms of our National Government. It outranks in accomplishment, measured by practical scientific contribution, any like governmental organization in all the other nations. It possesses none of the characteristics of many other bureaus of government which have created popular bias. Here is one Bureau devoid of political suggestion or aim with a personnel zealously devoted to labor in scientific re¬search - an organization marked by practical accomplishment, alleviating many of life's burdens, raking easier life's pathway, and unerringly pointing to life's possibilities.

Jan 1, 1936