Search Documents

By Albert L. Toenges

The State Division of Geology Arkansas Resources and Development Commission, and the Arkansas-Oklahoma Coal, Operators Association requested assistance from the Bureau of Mines in a study of coal-mining methods and practices in .Arkansas coal mines with the objective of reducing production costs. On October 7, 1946, a joint meeting was held by representatives of the Arkansas Resources and Development Commission, approximately 30 coal-mine Operators of the Arkansas -Oklahoma Coal Operaters Association, and representatives of the Bureau of Mines. The many problems confronting the coal industry in Arkansas, including mechanical mining in thin beds, costs, labor, and working time were discussed. Following this Meeting, a joint letter from Harold B. Foxhall, State geologist, and -P. R. Stewart, commissioner, Arkansas-Oklahoma Coal Operators Association, was addressed to Dr. R. R. Sayers; former ,Director of the Bureau of Mines, requesting that mining conditions in Arkansas be studied.

Jan 1, 1949

By Oscar Lee, B. W. Gandrud, F. D. DeVaney

"IntroductionFlue dust which results from the smelting of ores containing appreciable quantities of fines is one of the troublesome products of iron blast-furnace practice. Gases issuing from the furnaces at a high velocity carry small particles of coke, ore and flux into dust-collecting chambers. These particles constitute the flue dust. Lasses of iron ore through the production of flue dust vary between wide limits in the different furnaces, and depend on a number of factors, such as size and design of furnace, amount of fines in the ore, the operating conditions and the blast pressure.Blast-furnace operators of the Birmingham district keenly realize this waste. The ores are comparatively low grade and require more fuel than is ordinarily used elsewhere. Hence the flue dust is low in iron content and high in coke. As a result it is not in suitable condition for direct sintering. In many other iron and steel centers direct sintering is a common practice. In the Birmingham district efforts have been made to prevent this loss by recharging the dust into the furnace, but, as might be expected, a material fine enough to be blown out once will very likely be carried over again.In general, the flue-dust losses in this district will average 250 pounds per ton of pig iron produced, but at times the losses at different furnaces are substantially higher or lower than this figure. On the basis of the present rate of pig-iron production, the annual loss of flue dust exceeds 300,000 tons. The iron content of the dust probably averages 25 per cent, therefore about 75,000 tons of iron is wasted yearly, or about 3 per cent of the iron mined is lost in flue dust."

Jul 1, 1926

By E. K. Stanek

This report contains results of two major efforts related to electrical transients on mine electrical power systems. The first area concerns the use of digital computers to model mine electrical power systems and predict transients or duplicate field recordings of transients. Two existing general purpose circuit analysis programs were used. The first was the TRW Engineering System Simulator or TESS. The second was Electronic Circuit Analysis Program or ECAP. TESS proved to be superior to ECAP in several important characteristics, including system size limitations and modeling nonlinear elements. The second major topic covered in this report is the evaluation of commercially available surge suppression devices. These devices were found to be quite acceptable and guidelines for the selection and placement of surge suppressors were included. The final important item is a listing of the worst-case transients, from a design point of view, for ac and de utilization systems and ac distribution systems.

Jan 1, 1979

By W. R. McDonald

Part of the U.S. Bureau of Mines mission is to supply the U.S. mineral industries with information that is useful in planning to meet the Nation's critical and strategic mineral needs if a national emergency occurs. The Bureau conducted laboratory research including operating a nominal 100 lblh pilot plant to demonstrate the recovery and concentration of chromite by gravity and flotation operations from three northern California mineral deposits. Gravity beneficiation test results show that concentrates contained as much as 52 pet chromic oxide (CrZ03) with recoveries of about 80 pet. Results from the bench-scale unit operations of mineral liberation, tabling, vanning, spiraling, pinch sluice, work index, and thickener area determination tests are presented in this report.

Jan 1, 1990

By Barry W. Klein

The U.S. economy was considerably stronger in 1976 than in 1974 or 1975. Real gross national product (GNP) rose sharply in the first quarter of 1976 and then increased at a more moderate rate for the remainder of the year. The unemployment rate fell until June and then increased for moat of the remainder of the year, finishing at the same rate as it had started the year. The inflation rate continued to decline in 1976. Reasons for the relatively low rate (compared with those of 1974 and 1975) included small increases in food prices and only moderate increases in energy prices. Total U.S. output measured in terms of GNP increased 11.6% in 1976. Real GNP in 1972 constant dollars rose 6.2%. Inflation as measured by the implicit price deflator increased 5.1%. In real terms, gross private domestic investment for residential structures rose 22.7% in 1976 after declining 14.7%a in 1975; State and local Government expenditures increased 1.4% in 1976; and personal consumption expenditures for services rose 4.5%. The Federal Reserve Board (FRB) index of industrial production increased 10.2%.

Jan 1, 1978

By D. E. FOCG, A. E. Wells

When the United States entered the World War governmental agencies found little definite knowledge available as to the exact capacity of each sulphuric acid plant in the United States to manufacture acid under the stress of a great emergency. It is true that on account of the demand for acid for the manufacture of munitions for the Allies, prior to the entrance of this country into the war, most of the acid plants near industrial centers in the Eastern and Northern States were running at or nearly their maximum capacity, but, . for various reasons, many plants in these States and plants in other districts were not. For a number of years statistics as to the production of acid by the plants of the country were compiled by the United States Geological Survey, but obviously such figures did not give information as to the maximum capacities that might be available for meeting the he.a vy war ·requirements, or as to the steps that would have to be taken to bt-ing these capacities into use. During the summer and early fall of 1917 various attempts were made to obtain the desired information, but no satisfactory or complete data were obtained. Late in 1917, under the authority granted to the Bureau of Mines by the explosives act, the Director of the Bureau of Mines directed A. E. Wells, metallurgist of the bureau, to uiake a complete survey of the situation. Mr. Wells personally conferred with officials of the acid companies and visited most of the acid plants in the North that are east of the Mississippi River. The information obtained through this personal survey, together with that obtained through the ready cooperation of the subcommittee on ncids, and the subcommittee on fertilizers of the Committee on Chemicals of the Council of National Defense, enabled the preparation of a report containing the desired data concerning the sulphuric acid industry. This report was made immediately available to the War Industries Board and to those offices in the War and Navy Depart- ments that were most directly concerned in planning the explosives program and in obtaining the necessary supplies to produce the explosives. Beginning with this survey and report, the sulphuric acid section of the war minerals investigations of the Bureau of Mines took an active part in all matters pertaining to the sulphuric acid industry during the remainder of the war. Mr. Wells, the chief of the section, was appointed an associate chief of the sulphur, pyrite, and sulphuric acid sections of the War Industries Board. .Also, by this direct contact with the War Industries Board, the data obtained by Messrs. R. R. Hornor, H. A. Buehler, a.nd 0. Lindstrom, who were in charge, for the bureau, of the investigations concerning the supplies of pyrite and sulphur, were constantly made available to all interested Government agencies. D. E. Fogg, of New York City, was appointed chemical engineer to the sulphuric acid section to make special investigations relating to the acid industry, especially the possible utilization, in an emergency, of those sources of raw material.not then being used. Mr. E. E. Corbett, of Brooklyn, N. Y., was appointed chemical engineer to make investigations concerned primarily ,vith the conservation of acid. Direct and intimate contact with the industry was had through the close cooperation with the committee on acids of the Chemical Alliance, this committee during the greater part of 1918 occupying rooms with the acid section of the bureau. With the ending of the war and the close o:f the active work of the acid section of the bureau, the suggestion was made by many interested parties that a bulletin be prepared giving some qf the fun. damental and most important facts regarding the sulphuric acid industry, including a discussion of the technical :features of the manufacture of acid. During the war the bureau received -a vast number of inquiries in regard to various phases of the industry, a.nd this fact also made such a bulletin seem desirable. Therefore, the present bulletin was prepared to cover the main facts in regard to the industry in this country, including a discussion of the supplies of sulphur-bearing raw materials, the situation of the acid plants, the principal points in regard to manufacturing processes, and the uses of the acid. No attempt has been ma.de to discuss at length the manufacturing processes, as details differ more or less at the different plants and in general are carefully guarded by the acid ·companies. A great deal of the data given in this bulletin may be found in various pub]ications, but this is the first publication in which such data have been assembled and made readily available. Most of the data were obtained directly from observation and from cooperating acid companies or from individuals who had been or are now engaged in acid manufacturing and were liberal and generous in making their information available for publication. Care has been exercised to publish no data that were obtained as confidential by the bureau's representatives. The average acid manufacturer may be already more or less acquainted with most of the information presented in this bulletin, yet it is believed that the bulletin will be of value to those who wish to obtain a. general review of the present condition, both the economic and technical, of the sulphuric acid industry in the United States.

Jan 1, 1920

By H. W. St. Clair

Sampling of heterogeneous mixtures of fused metals or solidified melts is subject to errors not met in sampling finely ground ores or granular materials. These errors arise largely because of the segregation of constituent metals that usually takes place during solidification. It is seldom that a random sample of a lot of metal will represent the composition of the entire lot. The problem becomes especially difficult when it is necessary to make accurate analyses for a segregated impurity present in very small amounts. This paper discusses some of the pertinent experimental observations made in selecting a method for sampling melts of aluminum and zinc containing small amounts of iron and silicon as impurities. Although this experimental study dealt only with sampling this specific combination of metals, many aspects of the study apply generally to any mixture of mol ten metals containing minor constituents that segregate rapidly during freezing of the melt.

Jan 1, 1949

By Theodore Kootz

Manufacture of high-grade ferromanganese; as a rule; requires a low-phosphorus-manganese ore with 45 to 55 percent Mn, chiefly obtained in the Soviet Union, the British Dominions, and Brazil. Also, low-manganese ores have already been used for ferromanganese production, especially in North America .and Germany. During World War I, a process was developed in which a high-phosphorus ferromanganese or spiegeleisen was prepared in the blast furnace from law- or high-phosphorus manganiferous ores, then low-phosphorus manganese slag was prepared by refining under an acid slag, and this material was, worked into a low-phosphorus ferromanganese in the blast furnace.9/ Manufacture of useful manganese ores from a phosphorus-bearing spiegel with 12 to. 15 percent Mn, 4.5 percent C,, and 0.5 percent P by slagging in a refining furnace was reported by Joseph, Barrett, and Wood.10/ The spiegel was refined to 0.75 percent Mn, 3.4 percent C, and 0.45 percent P. Thereby, a slag with about 43 to 58 percent Mn and, about 10 percent Si02, was obtained. Hotter melts gave a smaller phosphorus content in the slag than cold melts. In addition, the phosphorus content of the slag varied with the manganese content of the intermediate metal.

Jan 1, 1952

By Frank J. Wiebelt

In its efforts to maintain production of tungsten during the recent war period, the Bureau of Mines explored certain parts of the properties of the Atolia Mining Co. in San Bernardino County, Calif., by diamond drilling. Owing to past production record and other available data, the area was considered attractive for possible development of new ore bodies. Scheelite occurs in narrow veins ranging in width from a fraction of an inch to several feet. The veins are in quartz monzonite in a zone 2 miles long and 500 feet wide. Production from the district was reported to have been over 1,000,000 units of W03. Twelve diamond-drill holes, totaling 5,056 feet, were drilled by the Bureau of Mines in the vicinity of the Papoose, Papoose No. 5, Amity, and Union mines, the tailings pond, and the "Old Spud Patch." The work began in August 1943 and was completed in June 1944. This publication briefly describes the history and deposits of the district and gives full details of the work performed by the Bureau.

Jan 1, 1950

By O. H. Metzger

This is one of a series of papers on placer mining in the western United States. The author has endeavored to give a general outline of the available placer deposits in Boise County, Idaho, together with a description of current practices and the recovery costs of the principal producers. The paper is based on a field examination by the author in May and June 1937. Boise County (fig. 1) is in the southwestern part of Idaho. It has a maximum length of 60 miles, a maximum width of 42 miles, and an area of approximately 1,600 square miles.

Jan 1, 1938

By John L. Miller

The synthetic fluormicas may be divided on the basis of silicon content into tetrasilicic, trisilicic, and disilicic. Properties of lead and barium disilicic fluormicas were determined to characterize these two representative members of the disilicic group. Properties described include unit-cell parameters from X-ray diffraction, optical data, chemical composition, density, melting point, and mechanical and dielectric properties. Both the lead and the barium micas were typically monoclinic; neither was sufficiently cleavable to yield usable mica splittings. Both yielded polycrystalline, machinable ceramics with excellent mechanical and dielectric properties.

Jan 1, 1963

By P. Nicholls

Patent records show that the idea that the burning of fuels can be improved by mixing or pretreating them with chemicals 6 dates back to the early years of the last century. By 1845, English and French patents included the specific beneficiations of elimination or reduction of smoke, soot, and clinker; reduction of the ashes, presumably meaning the total weight of refuse from the ashpit; elimination of sulphur fumes; increase in the rate of burning; increase in the time a given charge of fuel would last; and, in most patents, a saving of fuel. The earlier patents specified additions up to 80 pounds or more per ton of fuel, but after 1860 the quantity was rarely more than 4 pounds. There is no record of the extent to which these patents were commercialized, but after 1884 many American patents were assigned to companies specializing in treatment of coal, so it is probable that the products were marketed on a considerable scale at least as early as that date. From 1900 on, many companies marketed proprietary products that were sold under the general name of "fuel savers." Since its establishment in 1910, the Bureau of Mines has continually received inquiries about these products and, at the request of other govern-mental departments, has tested some used in accordance with the instructions of the purveyors; the results were all negative and, within the accuracy of measurements, the products had no effect on the burning.

Jan 1, 1937

By R. D. Leitch

Spontaneous firing of coal during storage end even during shipment has long been a serious problem, especially in some regions and with some coals, and methods for preventing such firing have been investigated at intervals for more than 70 years. Spontaneous or other firing of coal waste, either outside or inside mines, has also been a problem probably for as long as mining has been practiced extensively. Much trouble has been caused by such fires, and much money has been spent in attempts to extinguish them. It is known generally that surface waste banks in bituminous-coal fields are very likely to take fire sooner or later, but it is not known so generally that anthracite refuse-bark fires also are common and that at least some of them are more serious in their effect and results than being regarded merely as a nuisance. There surface refuse fires probably would have attracted much more than local attention long ago had it not been that they usually cause no more serious trouble than air pollution. A few supposedly effective methods of preventing or extinguishing spontaneous fires have been reported rather recently. Unless one or more of these prove to be widely applicable, methods of solving these problems are no more certain today than they have been for many years.

Jan 1, 1940

Five watersheds, ranging in size from 29 to 49 acres, were selected in East-Central Ohio to investigate the hydrologic and water quality conditions occurring before, during, and after surface mining. Four of the watersheds will undergo surface mining, involving either the Number 6, 9, 11, or 8 coal seams, and one watershed having an outcrop of the Number 6 coal will be operated as a control watershed. To determine the premining hydrologic and water quality conditions (Phase 1), physical information was obtained for each watershed and instrumentation was installed for obtaining hydrologic data and water quality samples. In addition to topographic maps, soils and vegetation maps were prepared. Stratigraphic columns were developed from geologic cores; networks of observation wells and of soil moisture access tubes were installed; and weather stations were established to measure temperature, humidity, wind and solar radiation, and to collect precipi¬tation samples. Field data were collected over a 10-month period for one watershed and for about 8 months on another watershed before surface mining began. The other watersheds continued in the premining data phase. These data were for precipitation, temperature, relative humidity, wind speed, solar radiation, snow and frozen soil, soil moisture, infiltration (rainfall simulator), spring discharge, runoff from watersheds, and ground-water levels. Also, samples of runoff and ground water were obtained for chemical analyses and additional samples of runoff were acquired for suspended sediment load determinations. Over the study period, precipitation was not very representative of the long term averages, but data are available from the control watershed for a representative 7 year period which should prove invaluable in modeling the hydrology of the project watersheds for the premined conditions. Spring discharges (before mining) from the upper aquifer of two of the watersheds averaged only 508 and 652 gallons daily. The proportion of precipitation occurring as surface runoff from the large watersheds ranged from 8 to 36 percent and the peak discharges from 5.86 to 81.95 cfs. Base-flow and runoff water samples from four of the watersheds (unmined conditions) were collected and analyzed quantitatively for 39 water quality parameters. Monthly precipitation samples sediment fractions of the base flow and runoff were analyzed for 22 and 17 parameters, respectively. The average concentrations of the water quality parameters for the watersheds (unmined), except for suspended solids, were as low or lower than the EPA recommended maximum allowable concentrations in drinking water. Several parameters in precipitation equaled or exceeded the levels of corresponding parameters in runoff water. The average concentration of suspended solids in storm runoff ranged from 118 to 1110 mg/l, and for base flow the range was from 44 to 247 mg/l; the higher concentrations were associated with the watersheds exhibiting the greatest disturbance. Iron ranged from an average of less than 3 µg/1 to 228 µg/1. Manganese ranged from less than 41 µg/1 to 334 µg/I. Ground-water systems (unmined condition) are described for the five project watersheds. Each watershed was found to have two major perched aquifers within the top 250 feet. Generally, these perched aquifers involve local flow systems, though flow across watershed boundaries in some areas. Recharge is mostly from local precipitation and discharge is mostly as spring flow, base flow, evapotranspiration, and leakage through the underlying confining bed. Shallow ground water was commonly of the calcium bicarbonate type. Although dissolved-solids concentration was generally 200 to 600 mg/1, brackish or salty ground water was present in several areas. A composite hydrologic model for the project watersheds will consist of separate ground-water, unsaturated flow, overland flow, and evapotranspiration component models. The ground-water model (a modified quasi-three--dimensional U. S. Geological Survey model) operates on a grid network and the newly formulated unsaturated flow model was divided into overlying prismatic elements for numerical solutions. The unsaturated flow model includes provision for incorporating the evapotranspiration model. An available distributed kinemetic overland flow model was utilized. An analyses was made of one of the costs of reclaiming coal mines; the legal and administrative costs of complying with legislation. Such costs borne by coal companies under the Ohio law are thought to be a surrogate of these costs under the new Federal law. Regression analyses were used to relate the legal and administrative costs to acres in the permit and the tonnage of coal produced.

Jan 1, 1978

By H. D. Pallister

A review of? reports and literature on the pyrite deposits at Pyriton, Ala., indicated that a large tonnage of pyrite, some of which contained a small amount of copper, had been mined and shipped to fertilizer plants throughout the South. The information contained in this literature tended to demonstrate that the ore occurred in separate lenses of greater or less extent and of varying thickness and richness in pyrite as well as in copper. The outcrop being parallel with the Atlantic Coastline Railroad and just south of it makes the deposits readily accessible for shipment. Slopes could be sunk as they were in the past in the ore body if it were of sufficient grade and thickness, and the ore could be hoisted up the slope and milled close to the slope mouth with an ample supply of water from Talladega Creek, which follows the outcrop closely.

Jan 1, 1949

By H. W. Kilau

The Bureau of Mines tested chromium-bearing waste slags from industrial stainless steel and other chrome alloy operations to determine their chromium leachability characteristics under acid precipitation conditions and to devise measures to prevent any pollution originating from this source. Two critical slag composition factors were found to control the chromium leachability: (1) CaO:Si02 ratio and (2) magnesium content. Above a 2.0 CaO:Si02 ratio, chromium exists in slag as CaO·Cr203, which can be vulnerable to leaching by acid precipitation especially if oxi-dized to CaCr04 when exposed to the environment over an extended period. Maximum chromium leachability from industrial slags occurred when the composition of the slag had about a 2.0 CaO:Si02 ratio. Between a 1.0 and 2.0 CaO:Si02 ratio, in the presence of sufficient magnesium, MgO ·Cr203 was formed, which is very resistant to oxidation and to dissolution by simulated acid precipitation. Addition of magnesium silicates to molten slag to fix the chromium in the MgO·Cr203 form was successful in preventing chromium leaching in simulated acid rain solutions. Experiments showed olivine and waste taconite tailings were suitable for this purpose. Olivine addition to a waste slag having a composition vulnerable to leaching (CaO:Si02 > 2) reduced the chromium leachability more than 80 pct.

Jan 1, 1984

By Michael E. Henderson

The U.S. Bureau of Mines (BOM) constructed the Hydraulic Transport Research Facility (HTRF) to investigate the hydraulic parameters relating to the transport of coarse coal. To achieve these goals in a timely and efficient manner, the Bureau contracted to Boeing Services International, Inc. (BSI) the responsibility of operating the HTRF and providing technical support. This data report is a summary of the testing and data results for the period from 16 September to 1 November 1983. The testing covered herein is for coarse 2-in by a (minus 50 mm) Pittsburgh Seam coal in a 12-in (3 00 mm) pipeline, at velocities ranging from 5 to 18 ft/s (1.5 to 5.5 m/s) and at concentrations ranging from 15 to 55 pct.

Jan 1, 1985

By Peter H. Toepfer

This report presents the factual data obtained by the Bureau of Mines during diamond-drilling investigation of the Sunset copper deposit in the Index mining district, Snohomish County, Wash. The Sunset mine, first produced copper ore in 1902, but its main period of activity was from 1923 through 1930, The mine has produced 263,500 tons of ore, from which 1,500 ounces of gold, 156,000 ounces of silver, and 12,912,000 bounds of copper-were recovered. The mine has, been idle since 1946

Jan 1, 1953

By M. E. Volin

The Ladd manganese deposits are in San Joaquin County, Calif., about 13 miles southwest of Tracy. The deposits are confined in two main areas of development, roughly about 1,700 feet apart horizontally, and known as the Ladd mine and Fabian mine, respectively. The deposits occur as interbedded lenses in the white cherts of the Franciscan formation. The ore minerals are bementite, rhodochrosite and psilomelane. As a part of the Bureau of Mines program of investigation and development of domestic mineral deposits, a development program was started. August 24, 1940, and completed on June 24, 1941. The Federal Geological Survey cooperated by mapping the geology and logging the drill cores. The program included road building, trenching, rehabilitating the mine workings, trenching underground excavation, sampling, and core drilling. The following pages mention the location, give a brief history, and note the physical features of +1-.1, district. Mine workings are sketched, the deposit is described and the plan of the project is noted. The work performed by the Bureau of Mines is explained in the concluding pages with a summary of the drill hole logs.

Jan 1, 1949

By R. F. Stewart

A nuclear meter based on measurement of prompt capture gamma rays is being developed for monitoring the sulfur content of coal streams. Equipment has been built to measure sulfur rapidly, and methods have been devised to compensate for changes in moisture, ash, and bulk density of coal flowing through a bin. Pilot plant tests of the system with various additives to different coals show a precision and accuracy of 0.02 percent sulfur and 0.04 percent sulfur, respectively. Based on these results, a hardwired meter has been fabricated for testing in a commercial coal preparation plant.

Jan 1, 1974