Search Documents

By R. H. Sprute

Extensive Bureau of Mines laboratory testing has shown that electrokinetic densification can be an effective method for dewatering and consolidating unclassified metal mine mill tailings. The report describes results of a limited field test of this technique. Eighteen-cubic-yard concrete model stopes, 18 feet long by 6 feet deep by 56 inches wide, were filled with unclassified tailings slurry from a metal mine in the Coeur d'Alene, Idaho, district. Five different tests were performed. They showed that a strong, dense, dewatered fill can be obtained in a reasonably short time using electrokinetics, with typical power consumption of 25 to 30 kW-hr/yd3 of densified fill. At present power costs in the Coeur d 'Alene district, this would amount to 10 to 12 cents/yd3.

Jan 1, 1975

By J. A. Woolf, E. S. Leaver, A. P. Towne

"INTRODUCTION A report giving experiments dealing with factors affecting the floatation of the most commonly occurring silver minerals was published years ago. At that time we could not obtain suitable samples of many of the so-called sulfo-salts of the base metals, which are generally silver--bearing and which comprise an appreciable percentage of the natural silver ores. Since Leaver and Woolf's work was published, samples of impure tennantite and enargite have been obtained, and considerable experimental flotation work has been done with synthetic mixtures prepared from these samples. During the present national emergency, research dealing solely with the recovery of gold and silver must necessarily be curtailed. However, many deposits of strategic minerals and critical base metals contain an appreciable amount of gold and silver, the recovery of which would aid greatly in recovering the strategies by taking care of a considerable part of the cost of treatment. Because of this, the recovery of precious metals should not be overlooked entirely. As the Bureau of Mines is now utilizing all of its facilities for the development of increased domestic productions of strategic and critical minerals, this is the last report not concerned primarily with such minerals that will be published until the war ends."

Sep 1, 1942

By N. S. Dalal, J. F. Mega, X. Shi, V. Vallyathan

Several studies have suggested that pulmonary toxicity to asbestos and silica may be mediated through oxidant-induced cell injury. We have reported recently that surface radicals associated with freshly fractured silica may be an imponant factor in cell injury and induction of pulmonary disease. Although the generation of oxygenated radicals in dust-cell interactions has been demonstrated, there are no data correlating the toxicity of a dust with the level of oxygen radical generation by the dust during its interaction with phagocytic cells. In the present study, we have investigated the in vitro generation of oxygen free radicals from human neutrophils and rat alveolar macrophages stimulated with freshly fractured silica, aged silica, amosite, crocidolite, chrysotilc, and a nontoxic dust, barite. Electron spin resonance (ESR) with the aid of a spin trap phenyl-N-ten-butyl nitronc (PBN) was used to measure the oxygen radicals generated during phagocytosis of the dusts. The relative toxicity index and ESR peak heights, on an equal surface area basis and normalized to barite as one, showed a direct relationship. The normalized toxicity indices and peak heights were: silica, 3.5 versus 2; chrysotile, 4 versus 2; crocidolite, 11 versus 8; and amosite, 26 versus 13. Addition of hydroxyl radical scavengers such as catalase, dimethyl sulfoxide, 1,3 dimethyl-2-thiourea (DMTU), sodium benzoate, and mannitol prevented the radical generation. Carmustine, a glutathione reductase- glutathione peroxidase inhibitor, caused a 5-fold increase in the radical generation. These results indicate that a nontoxic dust such as barite generates toxic oxygen radicals at a minimal level that can be quenched by the normal cellular defense system. For toxic dusts such as silica, amositc, chrysotile, and crocidolite, the potential for oxygen radical generation is enhanced by their surface propenies, physical dimensions, and the surface-based radical-generating redox sites. The enhanced radical generation may impair the cellular defense system, resulting in cell injury. Use of scavengers, chelators, and potentiating agents suggests the membrane-based oxidase system as the probable primary source of the radical-generating system. The data presented herein suggest the generation of oxygen free radicals as an important primary event in silica- as well as asbestos-induced cell injury.

Mar 1, 1992

By Cecil Q. Cupps

Results are presented of a comprehensive study of the characteristics of the original oil in the Weber sandstone reservoir, Rangely oil field, Colorado. Through the medium of subsurface sampling, adequately representative samples of the original reservoir oil were obtained from many parts of the reservoir over a period of 5 years concurrent with active development of the reservoir. Data of differential gas liberation, pressure-viscosity, and. pressure-volume-temperature relationships are shown for 12 subsurface oil samples. Data also are given of reservoir pressure and. temperature, composition of liberated or solution Gas, composition of 22 produced-gas samples, and Hempel analyses of crude-oil samples from 18 wells. The characteristics or physical properties of the 12 subsurface oil samples, as determined by laboratory analyses, were correlated with elevation of the top of the Weber sandstone. These relationships of oil characteristics to elevation in the reservoir show that only the oil in contact with the initial gas cap was gas-saturated at the existing pressure and temperature. The characteristics of the original reservoir oil were marked by an appreciable decrease of saturation pressure and solution gas-oil ratio and increase of viscosity and density with depth below the gas-oil contact. The composition of solution gas and of' produced was also was found to vary with elevation of the oil in the reservoir.

Jan 1, 1951

By Frederick C. Kohout

An advanced water-in-oil emulsion hydraulic fluid has been developed which meets defined laboratory performance criteria and which has given fully satisfactory results in a one-year underground mine test in two continuous miners. A novel method of monitoring fluid water content was demonstrated and incorporated into a test kit for use at or near the mine site. Test fluid fire resistance integrity as measured by the MSHA Schedule 30 procedure was maintained during the test and important fire resistance test variables identified.

Jan 1, 1979

By J. W. Paul

A study of mining methods and underground practices as they influence injury from falls of roof or coal reveals data as to the location in the mine where such injuries occur with the greatest frequency and as to some of the methods and practices which are in use for the prevention of injury. This paper, which presents statistics bearing on the frequency and place of occurrence of accidents and discusses regulations and practices which have resulted in a low-frequency rates from falls of roof and coal in a few representative mines, takes its information from mine-accident reports and from the results of studies conducted in a group of 80 mines in the bituminous coal fields of Western Pennsylvania, Ohio, and West Virginia. The statistics from this group of mines cover periods of one to four years but average 2 years and 7 months. During this time these mines produced over 110,400,000 tons of coal, equivalent to one-fifth of the annual production of all bituminous mines in the United States. The coal beds of the mines in the group studied are mostly flat, with local pitches of moderate degree. A number of mining plans are in use, each of which follows a general system of multiple entries, gross entries, and rooms. Room and pillar in panels either advancing, retreating, or half advance and half retreat, and the block system are employed. The methods of pillar extraction are by splitting, slabbing, pocket-and-stump, and open end. It is hoped that in presenting some of the details of the methods and practices at particular mines of this group which have commendable records in the prevention of injury some goad may accrue to many other bituminous mines which have similar natural conditions.

Jan 1, 1933

By W. P. Yant

[This report describes results of a study bf the carbon monoxide and particulate matter in the air of the Holland Tunnel and metropolitan New York made by the Bureau of Mines (which had participated in the development]

Jan 1, 1941

By A. J. Kraemer

This report on the physical and chemical properties of crude oils of California is one of a series on the producing districts of the United States. It includes a short discussion of results, tabulated data, and individual analyses of California crudes. Analyses of crude oils from the fields of Fresno, Kern, Los Angeles, Orange, and Ventura Counties have been published in Serials 25952 and 26083. The analyses reported in this paper corer samples that were obtained subsequent to the publication of Serials 2535 and 2608. The samples were obtained by members of the San Francisco office of the Bureau of Mines. The collecting of samples was facilitated by the courtesy of representatives of oil companies in California.

Jan 1, 1927

By J. W. Paul

[A study of mining methods and underground practices as they influence injury from falls of roof or coal reveals data as to the location in the mine where such injuries occur with the greatest frequency and as to some of the methods and practices which are in use for the prevention of injury. This paper, which presents statistics bearing on the frequency and place of occurrence of accidents and, discusses regulations and practices which have resulted in a low frequency rate from falls of roof and coal in a few representative mines takes its information from mine-accident reports and from the results of studies conducted in a group of 80 mines in the bituminous coal fields of western Pennsylvania, Ohio, and West Virginia. The statistics from this group of mines cover periods of one to four years but average 2 years and 7 months. During this time these mines produced over 110,400,000 tons of coal, equivalent to one-fifth of the annual production of all bituminous mines in the United States. The coal beds of the mines in the group studied are mostly flat, with local pitches of moderate degree. A number of mining plans are in use, each of which follows a general system of multiple entries, cross entries, and rooms. Room and pillar in panels either advancing, retreating, or half advance and half retreat and the block systems are employed. The methods of pillar extraction are by splitting, slabbing, pocket-and-stump, and open end. It is hoped that in presenting some of the details of the methods and practices at particular mines of this group which have commendable records in the prevention of injury some good may accrue to many other bituminous mines which 'nave similar natural conditions.]

Jan 1, 1933

By W. P. Yant

This report describes result of a study of the carbon monoxide and particulate matter in the air of the Holland, Tunnel and metropolitan New York made by the Bureau of Mines (which had participated in the development

Jan 1, 1941

By G. W. Jones

From evidence made available during the investigation, it was concluded that the first of a series of explosions occurred at 1:15 to 1:20 p.m. September 21, 1951, in an underground vault that housed pressure regulators on the gas-distribution lines that served Brighten. This explosion damaged the pressure regulators and permitted high-pressure gas to enter the distributing mains and individual-service lines. As a part of the gas-distribution system was not provided with means for protection against such excessive pressures, gas gained access to the interiors of many residences in this area and caused a series of disastrous explosions and fires, which took place during a period of approximately 2 hours after the initial explosion in the pressure-regulator vault. Two persons were killed in the first explosion in a residence, and a third person died of a heart attack attributed to the excitement that prevailed during the explosions and fires, Twenty-three persons were listed as injured. Forty-one residences were either destroyed or damaged - 11 by explosion and the remainder by fires, which developed as a result of gas leakage into residences. Fifteen residences were listed as "completely down" or "gutted." Unofficial estimates of property damage ranged from $1,000,000 to $1,500,000. In view of observations made and information obtained during the investigation, recommendations are presented in this report relative to the natural-gas distribution system in Brighton, which may be helpful in the prevention of similar accidents in this and other communities.

Jan 1, 1952

By Robert A. Clifton

This Bureau of Mines report discusses the mineralogy of zeolites, the properties that make them commercially valuable, the conditions of formation of both natural and synthetic zeolites, and present and potential markets.

Jan 1, 1987

By C. M. McKinney

This report contains Bureau of Mines routine crude-oil analyses of 20 samples from5 areas on the arctic slope of Alaska. Two samples were condensates from the South Barrow gasfield, Barrow Lakes area. The remaining 18 samples were crude oils from the following areas: Barrow Lakes, 1 seepage sample; Umiat, 10 well samples; Cape Simpson, 1 seepage sample and 3 well samples; Fish Creek, 2 well samples; and Wolf Creek, I well sample. Table 1 summarizes information on the origin of the crude-oil samples, and table 2 summarizes characteristics of the samples. Item numbers in both tables correspond to item numbers of the analyses at the end of this report, and the samples are referred to by these numbers throughout the text.

Jan 1, 1959

By Robert J. Anderson

"Introductory Statement:In melting the nonferrous metals and alloys for foundry and rolling-mill work, even with the best practice, there is always a loss, due principally to oxidation. Melting losses are a serious source of financial loss in brass and bronze practice, but they are especially serious in the case of aluminum and its light alloys because of the relatively high price of aluminum. The indications are that the melting losses in many aluminum foundries of the United States are at times high, and in some plants (especially where certain furnaces are used) they are entirely too high when compared with the average practice. The fact that the oxidation losses in melting aluminum and its light alloys are high is well known, but it is doubtful whether the factors governing the most suitable methods of melting for a minimum of dross are equally well known. The metal losses involved in melting are worthy of especial attention now because of the rapidly growing importance of the aluminum industry.Factors in the operation of furnaces which affect metal and fuel losses:The essential requirements in the commercial melting of any metal or alloy are that the melting losses should be low, the melting should be rapid, and the melting cost should be low. Certainly it may not be possible to obtain these requirements in any furnace selected at random, and it follows that the design and the operation of furnaces for melting different metals are subjects that warrant the most extensive study and tests. As a general rule, in the industrial operation of furnaces, run on aluminum and aluminum alloys, an effort is made to keep the dross and oxidation losses as low as possible. In attempting to hold dross losses low, numerous factors involved in metal melting may be overlooked, or at least disregarded, and the net practical result may be that the furnace is exceedingly wasteful of fuel. In the case of aluminum and its light alloys, the effect of increasing the temperature of melting, at least in an atmosphere containing free oxygen and nitrogen, is to increase the net melting loss."

Apr 1, 1921

By J. Howard Bird

The purpose of this publication is to discuss grounding mediums and the phases of grounding related to corrosion and cathodic protection. The material presented is believed to contribute to a better understanding of this subject. It also indicates more effective methods of reducing corrosion damage to metal structures and equipment in the mining industry by cathodic protection. The authors do not intend to discuss technical aspects but rather to explain the general principles of this method of inhibiting corrosion. The relationship between soil resistivity, protective grounding, and corrosion is presented. Corrosion causes the annual loss of billions of dollars; which can be greatly reduced. Losses in the mineral industry can be excessive owing to the extensive use of direct-current power, the presence of considerable dampness, and the frequent, indiscriminate use of dissimilar metals.

Jan 1, 1958

By B. E. Blair

The physical properties and related geological and petrographic data for 81 rock types obtained from operating mines or selected test sites are presented in this report. Most of these rock data were obtained to supplement structural studies in underground mines; however, the data may be equally applicable to other problems where the physical properties of rock are an important factor. Stress-strain curves are presented, where available, and free medium velocities from laboratory and field measurements are compared for several rock types. Rock-type, geographical, and geo-logical indexes are included for reference relative to physical property data in this and previously published Bureau of Mines physical property reports. INTRODUCTION This report presents the physical properties of 81 rock types from 16 different projects (sections 53-68). Three previous physical property reports2 3 4/ (herein after referred to as parts I, II, and III) presented data on 244 rock types from 52 project areas. (Part I included sections 1-25, part II sections 26-36, and part III sections 37-52).

Jan 1, 1956

By A. J. Kraemer

For a number of years the Bureau of Mines has been conducting an investi-gation of crude petroleum from producing fields in the United States and the Western Hemisphere and has published a series of reports on these fields. Analyses of crude-oil samples from some oil fields of Louisiana are given in Bulletin 291. Analyses Of 26 representative crude oils from various producing formations of southern Louisiana are given in this report. These samples are from 14 fields in 10 parishes in the southern part of the State, usually designated as the "Louisiana Gulf Coast area."

Jan 1, 1934

By Dale W. Richardson

Ductile hafnium was not obtained consistently by the conventional Kroll process. The bimetal reduction modification produced a more ductile hafnium by lowering the impurities, especially oxygen, in the sponge metal. Hafnium oxide was chlorinated in the presence of carbon to form anhydrous hafnium tetrachloride, which was reduced by sodium and magnesium in an inert atmosphere to produce sponge hafnium metal. After vacuum distillation to remove the byproducts, the sponge was arc-melted into ingot and rolled into strip. Metallic impurities were decreased by evaporating the hafnium tetrachloride from a fused salt. An excessive amount (over 1,200 parts per million (p.p.m.)) of aluminum was contained in some of the hafnium oxide, much of which remained as aluminum chloride in the hafnium tetrachloride during chlorination. Evaporation of the hafnium tetrachloride from a fused NaCI-KCI mixture during the Mg-Na reduction greatly lowered its aluminum content, as most of the aluminum and some of the other metallic impurities were retained by the fused salt.

Jan 1, 1961

By Robert J. Hundhausen, Robert M. Gammell

"INTRODUCTION Several mining properties in the Pine Creek area of the Coeur d'Alene mining region of Idaho were examined by engineers 3/ of the Bureau of Mines in 1942. As a result, a broad program of exploration was recommended for the area, particularly in the eastern end, where chances for the discovery of new ore shoots seemed favorable. This report describes the work done and the factual information obtained by the Bureau of lanes.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell Be Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch,. C. C. Ralston, chief, analyzes samples and performs beneficiation tests.The exploratory work at the Sidney mine was part of the activities of the Albany Division of the Mining Branch, S. H. Lorain, chief. Field work was under the direction of R. M. Gammell.Chemical analyses included in this report were performed at Reno, Nov., under the direction of A. C. Rice, acting engineer in charge, Rare and Precious Metals Experiment Station, Bureau of Mines. The ore-dressing tests were made under the direction of S. R. Zimmerley at the Bureau of Mines laboratory in Salt Lake City, Utah.The cooperation and assistance given by the owners of the Sidney Mining Co. is gratefully acknowledged."

Feb 1, 1948

By John J. Mulligan

The Bureau of Mines investigated the tin deposits of the Cape Mountain area during July and August 1962 to test the effectiveness of detrital-cover sampling in permafrost areas as a relatively cheap and simple means of guiding mine development and exploration. Results indicate that systematic detrita1-cover sampling can be used effectively to delineate obscure deposits with sufficient accuracy to permit sampling with a minimum of trenching or drilling. Extensions of known outcroppings were traced in sufficient detail to guide lode sampling and several previously unknown tin-bearing lodes were found and sampled. Lode sampling was limited to the minimum needed to establish the reliability of detrital-cover sampling results. The results of previous lode and placer investigations are summarized and detrital-cover sampling methods and results are described in detail.

Jan 1, 1966