Search Documents

By Jeffrey S. Walker

The purpose of this U.S. Bureau of Mines effort was to determine if ground movement caused by mining-induced subsidence is directly transferred to a structure and, if so, how that transfer takes place. Four concrete block walls with foundations were constructed and monitored over an active longwall panel. Three of the walls were located perpendicular to the direction of mining in zones where maximum inclination, maximum tension, and maximum curvature were predicted to occur. The fourth wall was constructed along the centerline of the panel, parallel to the direction of mining. All of the walls and the surrounding ground surface were instrumented with conventional survey monitoring points and extensometer stations to observe the vertical and horizontal movements. The fourth wall instrumentation also included continuously recording tiltmeters. The results of this investigation indicate that these simple structures respond to subsidence in a similar manner as the ground surface. This suggests that once the transfer mechanism is more fully defined, prediction models can be developed to accurately estimate the effect of mining on surface structures.

Jan 1, 1989

To provide operators of large-opening mines with a ventilation planning tool that will help them develop a healthier, safer, and more efficient ventilation system in the underground workplace.

Jan 3, 2006

By Maria I. De Rosa

High temperatures encountered by mine rescue teams during emergency situations may cause severe physiological strain, hindering the men from carrying out rescue and recovery missions. A prototype ice-cooling garment (ICG) was developed by the Bureau of Mines to alleviate physiological strain due to heat stress. The effectiveness of the garment was tested with acclimatized and unacclimatized subjects at a typical work rate (1,200 Btu/hr) expected during rescue operations and at various hot environments (97° to 113° F dry bulb and 80° to 89° F wet bulb). During exposures with the ice cooling garment, the subjects were able to maintain a safe deep body temperature of 100.4° F or below Without the garment, the deep body temperature rose beyond values of 100.4° F, a condition considered unsafe for continuous work in hot conditions. Both heart rate and skin temperature values were lower while wearing the ICG. Subjective observation also indicated a marked benefit by wearing the ICG.

Jan 1, 1976

By Richard E. Thill

Elastic wave velocities and moduli were determined by both the pulse and resonance methods in a large number of specimens of St. Cloud Gray Granodiorite and Tennessee marble under the same moisture, temperature, and stress environment. Long cylinders were first tested by the resonance method to obtain longitudinal bar and torsional wave velocity. The cylinders were then sectioned in half and tested by the pulse method to obtain the transient pulse velocity. These velocities were later used to obtain various moduli for comparison. Statistical comparisons between the Young's, shear, and bulk moduli and Poisson's ratios obtained independently by the pulse and resonance methods indicate that the methods do not give equivalent results in nearly isotropic rock. The amount of difference varies for each modulus, with the least difference (less than 5 pct) occurring in the shear modulus and the greatest difference (as high as 34 pct) in the bulk modulus. Moduli determinations in aluminum show much closer agreement between the pulse and resonance methods than in rock. The discrepancy in pulse and resonance results probably is caused by frequency dispersion effects and by differences in error sensitivity in the various formulas used to calculate the moduli.

Jan 1, 1974

To reduce the exposure of mining machine operators to respirable dust. Approach: A protective curtain of filtered air is blown down around the operator's head, from a manifold mounted on the machine canopy. How It Works: Mine air is drawn into the system through a filter which removes respirable dust. The filtered air enters a centrifugal blower which pushes it through a flexible hose to a manifold mounted on the canopy above the operator. Air leaves the manifold through a perforated plate and flows down around the operator's head. A photograph of an installed system can be seen in Figure 1. The second photograph, Figure 2, shows the sys-tem components. An important advantage of this dust protection system is that it is not worn or carried, or in any way connected to the operator. It is therefore not uncomfortable, encumbering, or

Jan 1, 1976

By John E. Kelley

A method for measuring the spark-shower radiance of metals when abraded on a grinding wheel was developed by the Bureau of Mines for evaluating the sparking tendency of metals. The radiance was measured in units of emissive power per solid angle per area of the detector. Over 100 metals were tested and rated relative to commercially pure iron. The metals tested included elemental metals, iron binary and ternary alloys, iron-carbon ternary alloys, commercial steels, nonferrous alloys, and a few hard-metal compounds. Some alloys were synthesized; others were obtained commercially. Alloys that possessed good strength properties were emphasized for selection. The results indicate that the spark-shower radiance of plain carbon steels and carbon alloy steels was greater than that of pure iron. Certain elements, particularly vanadium and chromium, reduced the sparking tendency of iron. Stainless steels and particularly nickel alloys displayed low spark-shower radiance. Some metallic elements had much lower radiance than iron; others, much greater. Plain carbon steels, heat treated to a variety of hardnesses, gave radiance values that generally increased with increasing hardness. The effect on sparking tendency of an increase in hardness of an alloy steel was studied. The sparking tendency increased with an increase in hardness to a maximum, then decreased with a further increase in hardness.

Jan 1, 1974

By Joseph A. Vanous

The inductive communication system was developed under this contract for use in the hoist of deep mines. This program was a four phase program with experimental dual frequency equipment resulting from Phase I, emergency single frequency equipment developed under Phase II, and equipment documentation required under Phase III. An additional emergency system was provided under Phase IV.

Jan 1, 1976

By H. B. Carroll

The performance of commercially available portable instrumentation for detecting nitrogen dioxide, sulfur dioxide, and hydrogen sulfide was evaluated. Length-of-stain detector tubes from several manufacturers were included in the study. The instruments were evaluated in atmospheres with 50-and 80-percent relative humidities at 75° F and containing test gas concentrations of 0.1, 0.25, 0.50, 1.0, 1.5, and 2.0 times the threshold limit values. The results from the gas analyzers were correlated with the known contaminant concentration by calculating and plotting an estimated line of regression, confidence limits, and correlation coefficient for each detector system. An increase in the relative humidity from 50 to 80 percent at /5° F changed the instrument response to the contaminants. The uncertainties in detection precision reported are for the observer-instrument system. The main difference or inconsistency in toxic gas concentrations determined with length-of-stain tubes resulted from the observer's interpretation of the results rather than from a predominant difference in the tubes.

Jan 1, 1975

By K. E. Stanfield

[Asphalt ~~d road oil ar8 the principal products manufactured from Wyor.1in~ Ilblack oilo" \r,hich, beca.use of th?lir hig.~ E\.sphal t and hig} sulfur COi.1Jce~1t, .!?re difficult e':ld costly to refine into hi?;h-gra.de motor f 101s, burning oils. and lucri ants by presont mothods. Accordin~ly. the demand for truHle asphaltic renidl urn for the construction of roade aJ1.d other uses is 3. controlling factor in the quantity of crud~ oil prod ICed. The increasiilg -u.tilization of special aST>ha.lts as ine}""Pensive bonding, in-]

Jan 1, 1941

By Kermit G. Davis, Sean Gallagher, William S. Marras, Kimberly Kovacs

This study evaluated spinal loads associated with lifting and hanging heavy mining cable in a variety of postures. This electrical cable can weigh up to 10 kg per metre and is often lifted in restricted spaces in underground coal mines. Seven male subjects performed eight cable lifting and hanging tasks, while trunk kinematic data and trunk muscle electromyograms (EMGs) were obtained. The eight tasks were combinations of four postures (standing, stooping kneeling on one knee, or kneeling on both knees) and two levels of cable load (0 N or 100 N load added to the existing cable weight). An EMG-assisted model was used to calculate forces and moments acting on the lumbar spine. A two-way split-plot ANOVA showed that increased load (p<0.05) and changes in lifting posture (p<0.05) independently affected trunk muscle recruitment and spinal loading. The increase in cable load resulted in higher EMG activity of all trunk muscles and increased axial and lateral bending moments on the spine (p < 0.05). Changes in posture caused more selective adjustments in muscle recruitment and affected the sagittal plane moment (p < 0.05). Despite the more selective nature of trunk EMG changes due to posture, the magnitude of changes in spinal loading was often quite dramatic. However, average compression values exceeded 3400 N for all cable lifting tasks.

By R. V. Ramani

One area of study in the Coal Mine Injury Analysis project was to illustrate and enhance the ability of mine safety management personnel to apply analytical techniques to injury experience data and to justify requests for funds for safety enhancement actions on a cost/benefit and other quantitative basis. Four volumes of this final project report detail (1) the objectives and scope of the mine safety management research, (2) the results of literature review, and case studies, and (3) models developed for mine safety management. The four volumes are titled as Volume III: Mine Safety Management, Volume IV: Analytical Techniques for Mine Safety Management; Volume V: Mine Safety Management Case Studies and Volume IX: Training Cost Model. In this volume, the quantitative procedures that have been developed for the mine-specific analyses of accident/injury experience data are presented and their applications are demonstrated in a summary form through case study examples. The quantitative procedures will aid mine safety management personnel to develop focused accident prevention strategies including training, as well as to justify the investment in such proactive programs through cost-benefit analyses.

Jan 1, 1993

Three complete connector assemblies and six separate contacts were submitted to a series of tests to establish the connectors permissibility and compliance with U. S. Bureau of Mines research Contract #H 0110423 D.C. portion. Test Procedure TPC-0118 was coordinated, and the test plan approved by the Bureau as fully complying with the intent of the contract for the direct current connectors. The components and connector assemblies have been demonstrated in testing that they meet or exceed all the requirements of the test procedure.

Jan 1, 1974

By David L. Bickel

The following instructions and descriptions are presented in two parts to assist an individual to make the borehole deformation gage transducer, and to assemble and test the three-component borehole deformation gage. This Bureau 8 of Mines three-component borehole deformation gage (4, 8, 11)2 fits in a 1-1/2-in-diameter borehole that is drilled in rock and then overcored to determine rock stress.

Jan 1, 1978

By Stephen R. Iverson, Bill M. Stewart, Michael J. Beus

The U.S. Mine Safety and Health Administration (MSHA) has identified ore pass hazards as a significant safety problem in underground metal mines in the United States injury and fatality data show that many injuries are related to pulling or freeing ore pass chutes and structural failures of control gates and ore pass walls. Researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health are investigating these hazards and developing methods to improve safety during transport of ore and waste. Particle flow analysis methods were used to simulate chute and control gate response to various material loading scenarios. Results from computer models indicate that dynamic impacts from ore and waste rock might be considerably greater than theory predicts. Static and dynamic loads were measured in a laboratory setting using scaled ore (sass mock-ups. Field tests were initiated in an active ore pass to determine actual static and dynamic loads. Field data were compared to computer results and indicated that impact and total static loads were substantially less than the computer model results suggested. Damping factors, normal and shear stiffness, and mass frictional characteristics have a significant effect on particle flow and resulting impact loads.

By H. D. Kline

This paper describes the methods of mining and washing brown iron are in 1957 at the Sawyer mine, leased by Wayne County Mining Co., and the Fore mine, leased by Four Mining Co., both in southern Missouri; it is one of a series prepared by the Federal Bureau of Mines on mining and milling methods and costs in various districts of the United States. The Sawyer mine is in Wayne County, about 10 miles north-northeast of Williamsville (fig. 1); the Fore mine is in Howell County, about 20 miles southwest of West Plains (fig. 2). Both are open-pit mines from which the crude are was upgraded by washing and hand-sorting to produce are of grade and quality suitable for sale to operators of iron and steel furnaces. The operations described are typical of many others that produce or have produced marketable brown iron are from small sedimentary deposits, several hundred of which outcrop on the crests or hill sides of southern Missouri (fig. 3). The 1957 production of marketable brown iron are by 40 separate operations in the southern part of the State was 281,427 wet long tons, valued at $1,637,243. Production from the Sawyer mine that year was 17,000 dry long tons of washed are, and from the Fore mine, 20,816 dry long tons.

Jan 1, 1960

By John J. Sammarco

The U.S. Bureau of Mines has developed a regulated, intrinsically safe, rechargeable power supply for portable electronic equipment for underground use. The regulated output is ideal for microprocessor power requirements and is suited for operation in hazardous environments. Two rechargeable, sealed batteries are contained within the power supply. Provisions are made to use an external source of power if these batteries fail. Provisions are also made to charge these internal batteries when needed. The circuit is composed of three main circuits: the main regulator circuit, the input protection circuit, and the output protection circuit. The main regulator circuit provides remote voltage sensing, current sensing, fault monitoring, and internal thermal protection. The input protection circuit checks for excessive input current and low battery conditions. The output protection circuit contains two overvoltage detection devices. Schematics, a parts list, and a calibration procedure are provided in this report to enable readers to fabricate the power supply.

Jan 1, 1989

By N. S. Dalal, X. Shi

"Electron spin resonance measurements provide evidence for the formation of long-lived Cr(V) intermediates in the reduction of Cr(Vl) by glutathione redtuctase in the presence of NADPH and for the hydroxyl radical formation during the glutathione reductase catalyzed reduction of Cr(Vl). Hydrogen peroxide suppresses Cr(V) and enhances the formation of hydroxyl radicals. Thus Cr(V) intermediates catalyze generation of hydroxyl radicals from hydrogen peroxide through a Fenton-like reaction. Thus the mechanism of Cr(VI) toxicity might involve the interaction between macromolecules and the hydroxyl radicals.C(Vl) compounds have been found to exert serious toxic and carcinogenic effects on humans and animals (1-3). In contrast, most Cr(III) compounds are relatively nontoxic, noncarcinogenic, and nonmutagenic (1,4). Cr(VI) and Cr(III) oxidation states are different in their metabolic pathways: Cr(VI) , ions are rapidly transported across cellular membrane (1,4,5), while Cr[III) moieties do not easily penetrate cells and are not oxidized by cellular constituents (!). Since it is known that the reduction of Cr(VI) ion is required for its reaction with DNA (1), the molecular mechanisms for the intracellular Cr(Vl) reduction has been the focus of current studies but the details are still not understood.Earlier studies on the mechanism of Cr(Vl) reduction include those on the reduction of Cr(VIJ by glutathione (GSH) .0,6-8), ascorbic acid (9), glucose (10), lactose (IO), galacturonic acid (11), microsome (12), and mitochondrial electron transport chain complexes (13). These studies have shown that the Cr(VI) reduction involves the formation of Cr(V)-containing species which are often considered to be the toxic form of chromium. Thus far, however, no information is· available on the subsequent fate of those biologically formed Cr(V) species, in particular employing well defined biochemical systems. In this context, we report here our investigations of the reduction of Cr(VI) by glutathione reductase (GSSG-R). This enzyme was selected because it is ubiquitously present in cellular systems and it has been postulated to be involved in the Cr(VI) reduction (14-17) but the underlying mechanism has not been clarified. We find that the reduction proces·s involves not only Cr(V) but also ·OH radicals. We further investigate the reactivity of Cr(V) and find that it catalyzes generation of OH radical from H2O 2 through a Fenton-like reaction. The role of ·OH in Cr(VI) carcinogenicity is suggested from this study."

Jan 1, 1989

By D. Harrington

The code of hoisting signals for use in mines hoisting from one level, as suggested in this publication, is submitted to induce consideration of this subject by representative groups of the coal-mining industry, such as the lithe Inspectors Institute of America, National Coal Association, American Mining Congress, and others, as well as to -furnish a code of signals for use in those mines operated in States that do not have regulatory hoisting codes in their mining laws, or regulations. The signal codes described in this publication apply only to mines hoisting from one level and to slope mines. Mines that hoist from more than one level are referred to Bureau of Mines Information Circular 7289 Suggested Hoisting-Signal Code For Metal Mine Shafts, which suggests signals for hoisting from various levels or stations.

Jan 1, 1944

By Patrick J. Cain

The fatigue-failure characteristics under high-frequency (10 KHz) cyclic loading were determined for a marble, granite, and quartzite. The rock speci-mens were cyclicly loaded (using a high-power piezoelectric sonic transducer) at a constant strain amplitude generated by forming a longitudinal standing stress (strain) wave in the cylindrical test specimen. The number of load cycles required to fail each rock type at a given strain amplitude was deter-mined. The fatigue fractures were tensile in nature and the fracture load amplitudes were as low as 30 pct of the static tensile strength. Also the internal heating of the rock caused by the material damping (internal friction) was measured. The damping and internal heat generation in the specimens was analyzed to show that nearly all of the power input can be accounted for as a change in enthalpy in the specimen. Using these results the thermal strain in the rock was calculated to evaluate its contribution to fatigue failure. The thermal strain was found to range up to 30 pct of the dynamic strain amplitude depending on the load amplitude and the number of load cycles. The specific energy required for failure was determined and possible applications of the high-frequency fatigue fragmentation process are discussed.

Jan 1, 1975

By John M. Gomes

The preparation of tungsten carbide by molten-salt electrolysis was investigated. Sodium tungstate in the electrolyte and carbon from the graphite anode were the source materials, Optimum results were obtained with an electrolyte consisting of 83 mole-percent sodium chloride and 5.7 mole-percent each of sodium tungstate, sodium metaborate, and sodium hydroxide; a temperature of 1,000° to 1,025° C; an anode current density of 37 amp/dm2 or less; and an initial cathode current density of 150 amp/dm2. The yield was approximately 0.45 g/amp hr. The electrolytic tungsten carbide product contained approximately 5.4 weight-percent combined carbon as compared to 6.1 weight-percent for pure tungsten carbide. Microhardness of the electrolytic tungsten carbide, determined with a 50-gram load, varied from 3,480 to 3,970 dph. The material was friable and could be ground in a laboratory ball mill to less than 400-mesh particle size.

Jan 1, 1969