Search Documents

By T. G. Sitharam, P. B. Choudhury

Prediction of ground vibration (peak particle velocity, PPV) and frequency is an important task in geoscience. Till date, many empirical equations are derived from conducting trial blasts in the mines, to arrive at attenuation predictors. These predictors are usually site dependant and hold good for one particular type of rock/strata. These predictors cannot be used for geologically different rocks/strata. This paper presents the application of support vector machine (SVM) model, for predicting blast induced ground vibration and frequency, using a one comprehensive model for three different types of rock. Inputs to the SVM model formulation involve twenty one parameters consisting of geotechnical properties of the rock mass, blast design geometry and explosive properties, and the output of the formulated model is peak particle velocity and its associated frequency. The data has been acquired from eight limestone mine, five coal mine and two manganese mines. The comprehensive SVM model is formulated using 400 datasets and tested with 143 datasets. The performance indicators to the model not only justify its formulation but also the advantages it has over site specific predictor models. The SVM model not only predicts PPV, with higher correlation coefficients as compared to predictor equations, but also the associated frequency.

Jan 1, 2010

By Vitor Barcelos, Eduardo Elói, Gabriella Vaz, Davi Oliveira, Leandro Silveira

Following a routine production blast at Vale S.A.'s Itabira Mine in the Quadrilátero Ferrífero region of Minas Gerais, Brazil, nearby residents registered complaints about blast-induced vibrations. Analysis of the blast footage revealed that multiple blastholes were detonated simultaneously, resulting in a higher-than-expected charge per delay, ground vibration and cratering even though the electronic delay timing was configured correctly. Subsequent blasts within the mine's soft schist region confirmed the occurrence of sympathetic detonation. Mitigating or eliminating this phenomenon is critical for the mine's operation. Two dynamic pressure tests were conducted using carbon resistors together with typical VOD monitor maintaining the standard booster, electronic detonator, and a blend of 70% emulsion with 30% ammonium nitrate explosive. The tests involved increasing the distance between the central hole (detonated first) and the four surrounding holes in a five-hole sequence. Unfortunately, sympathetic detonation occurred in all these tests. To address this issue, a new explosive with a lower density and detonation velocity was tested. This approach proved promising, as no sympathetic detonation occurred. By leveraging the data obtained from this study, engineers can now identify situations at risk of sympathetic detonation and implement preventive measures, such as selecting the appropriate explosive and recommending safe minimum burden and spacing settings as well as confinement level for each blast while maintaining the desired level of rock fragmentation.

Jan 21, 2025

"In this work a blasting seismograph was tested on a vibration shaker controlled by a single-point laser Doppler vibrometer (LDV). A total of 43 tests were made to measure the transfer properties(transmissibility and phase shift) of the basic elements of the full monitoring chain and investigate theperformance of the full system. The main elements of the seismograph are described by second ordertransfer functions with typical parameters calibrated through nonlinear fit of the measured responses. The resulting transfer function is used to compare the behavior of the tested seismograph with fourtheoretical seismographs representative of those used in blasting. Fifteen theoretical inputs are runthrough the transfer function of each seismograph to assess their steady-response. The error (expressed as gain) in the peak velocity has been assessed. It varies from -1.5 to 2.3 dB (equivalent to atransmissibility of 0.84 to 1.3, respectively) depending on the seismograph and frequencies of the input.The largest errors occurred for input signals with frequencies in the low (<32 Hz) or high ranges (>125Hz), where the mechanical, electronics and digital parts of the seismograph modify the signals. Seismographs with the nominal transfer function described by DIN 45669:1:2010 are ranked with the smallest errors. Monitoring devices with transmissibility around one in a narrow bandwidth, in line with ISEE suggested criteria for amplitude response, involve large phase shifts at low and high frequencies, resulting in a worst performance."

Jan 1, 2017

By Dale S. Preece, Lee M. Taylor

Computer simulation of the physics involved in conventional rock blasting can be split into two phases; transient stress wave propagation and rock motion. Because the two phases involve totally different mechanisms and time scales, they must be numerically modeled with two different computer programs. The first phase is usually modeled with a finite element or finite difference code which treats the rock ss a continuum and simulates the transient stress wave and subsequent fragmentation of the rock. The second phase is usually modeled with a distinct element technique where the rock mass after fragmentation is no longer treated as a continuum but as a finite number of distinct particles that interact with each other through collision mechanics.

Jan 1, 1989

By Gungor Tuncer, Ali Kahriman, Abdulkadir Karadogan

In the bench blasting, the realisation of an economic, and safe blasting is only possible with a reliable blasting design on condition that considering all sequential activities such as drillingblasting, excavation-loading, haulage, crushing (especially primer crushing). Here what we mean with a good, and reliable design is that ensures an almost displaced, adequately swelled muckpile with desired fragmentation degree for the loaders effectivity, and succesive usage. Meanwhile it must also has no environmental problems such as ground vibration, air blast, and rock flyings, or at least these matters have to be minimised. Two main parameters which have generally being questioned to achieve a safe and economic design on any rock conditions, are specific charge, and burden. In the condition of determining these elements, the other blasting parameters could be calculated according to them, and the blasting design could be completed. Within the scope of this study, it was aimed to determine the optimal blasting conditions of gypsum which is major rock unit of overburden at Sivas Celestine open pit mine. First of all, the engineering (mass, and material) and digging difficulty classifications of gypsum were done according to the current classification systems by using the results of field and laboratory studies. Then the blasting system which was being used on all rock units, was considered, and the necessary data were obtained. After previewing the site properties, predesigns were done, and applied by adopting Langefors design model. The necessary adjustments were done before, during, and after the shots, and the applications were observed. In order to determine, and record the data from each shots properly, a practical form was developed, and all data were transfered to these forms which give information about the blasting results such as muckpile displacement, and height, average particle size, back break, and rock fly existence, number of boulders etc. The blasting parameters such as burden, hole diameter, hole inclination, the amount and position of primers, bench height, delay sequence, and blasting geometry were considered for the iteration of each shots. During the applications, ANFO, gelatine dynamite, and electric delay detonators were used as explosives.

Jan 1, 2004

By David Yanez

The hydroelectric project "El Cajón" is currently under construction in the state of Nayarit, on the Santiago River, in western Mexico. This project is comprised of a Concrete Face Rockfill Dam (CFRD) with a rockfill necessity of 10,5 million cubic meters and it reaches a height of 188 m. The generation equipment includes two turbines with a total installed capacity of 750 MW.

Jan 1, 2006

By Kamal Wadhwa

Liquid oxygen explosives have been used in India for well over 5 decades now. These are being extensively used both for shallow and deep hole blasting in the various opencast mines and quarries for mining of coal, limestone, ironore, bauxite, magnesite etc. IOL Ltd., are the pioneers in the introduction of these explosives in India and are marketing these under the brand name 'LOXITE'.

Jan 1, 1991

By G. Geremia, M. I. Serrano, L. Costa, Strohaecker

The advances in electronics and the development of more efficient algorithms, allow for the designing of more complex and sophisticated automated systems. The new devices include lighter, faster, reliable, and stronger robot manipulators. One available technology, with relatively low cost, is a simple robot manipulator controlled by remote control. The device has been designed to be used in both mining and law enforcement, where it can be useful for inspection, rescue, gas analysis, and even to manipulate dangerous objects, such as explosives. The applications may even include the rescue of trapped miners in risky environments. The major advantage is the fact that the robot can be controlled with a remote and monitored through a video camera, minimizing human exposure to hazardous areas, where robots can perform tasks in an aggressive atmosphere and confined spaces. This article presents a mining robot manipulator controlled by remote control, using video cameras for positioning and sensors for movements, which are located on the operator's arm. With this system, it is possible to create a sensation of virtual reality, allowing easy operation for anyone trained in dealing with explosives, rescues, or other dangerous tasks. Blasting and mining are becoming perfect applications for robots, and its use should increase very soon. The results are discussed and presented for the brand new Xiru 01 robot manipulator.

Jan 1, 2010

By Sedat Esen

"This paper presents a critical review of the fragmentation data obtained from some large open pit copper and gold mines. Database ncludes 35 mines with Uniaxial Compressive Strength values ranging from 19 MPa to 227 MPa (2756 psi to 32923 psi). Variation in the fragmentation data and the causes are discussed in detail. Quality assurance/quality control (QA/QC) in drilling and blasting was shown to have significant impact on fragmentation. In addition, controllable blast design parameters including drill pattern, powder factor, blast timing, stemming length, etc as well as the large blast sizes havesignificant potential to improve fragmentation. Feed size requirements of crushing and grinding circuits were discussed in detail. The paper discusses the effects of different size fractions (top size, 80 %passing size and % passing 10 mm (0.5 in)) on the downstream processes and the role of the fragmentation model in the mine to mill process. Blast domains based on rock strength and structure canbe established by using a fragmentation model which is calibrated using measured fragmentation data. This allows the blast engineer to compensate for changing rock characteristics and stabilize the ROMfragmentation size and result in increased crusher and mill throughput. Two case studies were presented to demonstrate the benefits achieved in downstream processes. Main benefits were reduced downtime at crusher circuits, improved mill throughput as well as reduced total operating cost. A simple relationbetween uniaxial compressive strength and powder factor was proposed using the database for the optimized mines as a guideline to allow site engineers to compare their sites against the other sites."

Jan 1, 2017

By David Harrison, Brian Harrison

The Army Corps of Engineers completed the Charleroi Lock and Dam in 1932. It is located on the Monongahela river approximately 22 miles (35k) south of Pittsburgh in Charleroi, Pennsylvania. It is comprised of a 420-foot (128m) gated dam, and a 720-foot (219m) by 56-foot (17m) land side lock, which provides for a 16.6 foot (5m) vertical lift.

Jan 1, 2018

By Bonifacio Degay, Mike Lovitt

PT Freeport Indonesia is a block cave mine that now utilizes an advanced undercut method to set up the min in the Deep Ore Zone (DOZ). In this method a slice of rock (undercut) is broken such that it sits on top of the drawbell level. The drawbells are developed to channel the broken ore into the extraction level and to enable the caving orebody to be drawn out in an even and controlled manner. These drawbells are difficult to form due to the small amount of void that can be developed in the low strength rock before firing. Starting with two rises of 2m square, the void ratio for the entire drawbell around 6%, which would normally result in a frozen and unproductive blast. Orica -Mining Services have worked with PT Freeport in a collaborative effort to find a solution to the mining problem. With excellent control of timing of the blasting it is possible to get fluid flow of blasted rock out of the draw points such that more void can be made available for blasting the remaining parts of the drawbell. The i-konTM electronic blasting system gives the exacting control of timing within the blast to achieve this Dynamic Void Generation (DVG). The solution stops the need to charge close to brows in the drawbells and reduces the cost and time related to developing initial blast voidage. This paper identifies the results of the trials including design, photographic evidence and vibration analysis. The flexibility and accurate timing of this electronic blasting system has enabled single hole initiation rather than 4 or more holes being initiated together, thereby reducing the damaging vibrations to the extraction level.

Jan 1, 2004

By W B. Gregg

"A review, update, and expansion of Thiokol’s presentation at BAl’s Fiih High Tech Seminar titled ‘ADetonator - An Era of Precision in All-Electronic Detonators” is provided herein (and should be considered as a supplement to that publication). Thiokol is currently in the development and field evaluation phase of activities for our ACCUBLASTTM all-electronic detonator. The ACCUBLASTTM detonator uses a semiconductor bridge (an electronic match) in place of a conventional hot wire to initiate a safer, less sensitive material, titanium subhydride potassium perchlorate. The device is programmable to provide blast delays in one millisecond increments ranging from 1 to 500 milliseconds. The ACCUBLASTTM detonator combines an all-electronic programmable timer coupled with a semiconductor bridge to ensure detonation timing accuracy with +I00 microsecond precision. Initial development and field testing have been completed. These tests have verified ACCUBLASTTM detonators’ precision."

Jan 1, 1995

By BernardThierry

To be able to precisely predict the result of a mine blast before pressing the button is a goal for many blasters due to the environmental and economic constraints of our century. Based on the fundamental fracturing of the mechanism of rocks by explosives, the most recent research in digital modeling, the power of present computers, and the possibilities offered by drones, we have designed a realistic digital 3D simulation model for mine blasts. This new type of model enables us to concurrently simulate the fragmentation of the rock, its movement and the associated seismic levels, all within a few minutes, which is a time compatible with a production cycle. Due to the complexity of the model, this article reveals the main principles and compares the results of simulations with on-site measurements in various sectors, i.e. quarries, mines and tunnels.

By Satish R. Kate

Explosive is a chemical energy, which on detonation is released instantaneously with extremely high speed and under high pressure. It is used to meet the basic requirement for breaking of rocks. The productivity is the function of Drilling, Explosives and Fragmentation. Thus, the quality of explosives (energy content) is the key to get desired fragmentation. The variation in energy of explosives and volume of rock per hole have direct impact on fragmentation and cost of excavation (drilling and explosive costs). With the application of higher and higher energy content explosives, it is possible to expand the drilling patterns, i.e. volume in cum. per borehole. As such, higher drill productivity and higher production from the given number of holes can be achieved by adopting appropriate energy content in explosives, and suitable drill pattern for getting desired fragmentation.

Jan 1, 1998

By C. Adcock, R. Farnfield, G. Adderley

The use of explosives to create special effects in the film industry is a well-known past time. A recent production required simulation of a large scale water splash from the effect of a statue falling from a cliff edge and impacting on an open body of water. This was to be achieved through the use of precisely delayed explosions detonated near the surface of the water. A survey of the area revealed a breeding farm for sea bass approximately 250 metres (273 yards) from the intended blast area. It was initially thought that the water pressures produced for the detonation of the explosives may cause harm to the fish. Much work has been carried out over the past few decades on the effect of open water blasting and its effects on aquatic wildlife; this includes water pressure modelling techniques which can be used as predictive tools.

Jan 1, 2010

Jan 1, 2002

By G Alan Foster

This paper discusses the cause of air blast and modern techniques to reduce this at the source. In addition it raises the problem of their marked variability due to prevailing weather conditions and how weather data can be obtained and used in the control of air blast.

Jan 1, 1975

By Jean-Francois Lagueux, Andre Pomerleau

Goldex Mine is an underground mine located near the town of Val-d’Or. Multiple innovations were required to work the mine. Due to its low grade, it was important to develop a bulk mining method to economically extract the ore. The method used is a combination between shrinkage stope and long holes stope methods. This modified method is more than adequate; however, all of the ore body must be liberated in a very short period of time. Therefore, to bring down 23.0 M tonne (25.3 M ton) of ore, large blasts up to 1.8 M tonne (2.0 M ton) are required. The situation is also complicated by the fact that the mine is located in a residential area. No less that 40 homes are built within a 1 km (0.62 mile) radius of the mine site.

Jan 1, 2011

By Sharon K. Reamer, Klaus G. Hinzen, Brian W. Stump

"This study investigates seismic wave propagation from two production shots in a limestone quarry. Our motivation is to investigate the efficiency of two superpositioning techniques. The production shots consisted of an 18 and 20 hole explosive array detonated in a single row with constant delay times of 32 and 20 ms, respectively. A single shot was fired on a neighboring part of the quarry bench. The experiments were instrumented with 20 three component seismometers (35-120 m range). The computer-controlled electronic firing system resulted in firing time deviations of less than 1.4% of desired fired times. Linear superpositioning with the observed single shot data produces seismograms which adequately reproduce temporal effects of the multiple explosions; however, spatial effects due to the extended source length (68-76 m) are not modeled with this method. Linear superpositioning with individual half-space Green's functions for each explosion in thearray convolved with a calculated Mueller-Murphy source produces seismograms which match the time duration of the observed production shot seismograms and differ in absolute peak amplitude by less than a factor of three. Parameter estimation for the source is taken from chemical explosion study results. The single source model differs in amplitude from the observed single source seismograms by a factor of 2.3."

Jan 1, 1991

By Mario Karfakis, G. Langlois

Well stimulation is the process by which any production well, whether for production (extraction), storage (injection) or deep interaction (remediation, monitoring, etc) can be made or stimulated to flow at higher levels. This stimulation is driven by active methods to increase the permeability in the near-well environment and create a larger zone of communication between a well and the reservoir it services. Well stimulation is a crucial aspect of well completion and reservoir engineering and is a subject of careful pre-drilling planning. In many modern industrial endeavors the effectiveness of well stimulation is often critical to economic viability. Because of the broad impact of well engineering on several large industries (petroleum and natural gas extraction and storage, geothermal power, groundwater monitoring, extraction and management, environmental remediation, mining and minerals extraction, etc.) changes in the state of the art in well engineering and well stimulation can affect the capabilities of very diverse and disparate industries. This paper is an effort to communicate the status and effectiveness of current practice and technology in well stimulation. The intention being that effective communication of progress can spur innovation in industries that require well stimulation but are removed from immediate communication of technological or practical improvement.

Jan 1, 2009