Search Documents

By W. J. Birch

The recording of information is critical to the blasting process, whether it be for planning purposes, statutory requirements or environmental compliance. The review and analysis of past data can play a key part in a blast.s design. Statutory records must be held to preserve operational licenses and well-maintained monitoring records are a vital defence for today.s litigious society. However a single blasting event can be responsible for generating vast amounts of data. This information maybe collected pre or post-blast and in their individual ways may have a requirement to be logged, processed, analysed, reviewed and reported before eventually being archived.

Jan 1, 2002

By Scott Gustfason, Richard N. Snyder

What is a safe stand-off distance? Recent mishaps using conventional blasting equipment have seen flyrock as distant as 3,750 feet from the blast area, or close to three-quarters of a mile, therefore, whether below ground, under water, in surface quarries or at a structural demolition site, data signals riding a radio wave promise a new horizon for the users of both electric and non electric blasting circuits.

Jan 1, 1987

By Dennis J. Viscusi, James H. III Rowland, Lon D. Santis, Mark H. Weslowski

This paper describes the procedure for analysis of toxic fumes from the detonation of high explosives using the Large Chamber at the U.S. Bureau of Mines (USBM), Pittsburgh Research Center (PRC). This test is specified in 30 Code of Federal Regulations (CFR) Part 15.20 (g) as a requirement for the Mine Safety and Health Administration's (MSHA) approval of an explosive as permissible for use in underground coal mines. The Large Chamber replaced the Bichel gauge and CrawshawJones (C-J) apparatus in the 1989 revision of these regulations. To determine the safety of an explosive in terms of toxic gas production, the Large Chamber Test attempts to simulate mine conditions and miners' exposure to toxic gases from explosives.

Jan 1, 1995

By Claude Cunningham

Simple bulk energy rating of explosives obscures the realities of how these deliver their energy, and diverts attention from the key question of controlling blasting results. Explosive performance is directly related to the pressure pulse impacting on the blasthole wall. This is helpfully visualised by comparing the adiabatic expansion plots for explosives of interest on the right scales and axes. The simple comparison of a pure emulsion with pure ANFO illustrates the practical significance of the intrinsic behaviour of these opposed formulations, showing that the emulsion can be expected to work more by softening rock, while ANFO will tend more to crack it. The explanation for these differences lies in the high shock, low sustained pressure of the former relative to the latter. The technique is readily applied, if a good detonation code is available and able to swap data into a spreadsheet. Any differences between codes will emerge most strongly in comparing the gamma plots.

Jan 1, 2002

By Nadir Plasencia, Rogerio: Neves Mota

The evaluation of vibrations induced to build structures is one of the main concerns when dealing with blast works. EDP, the main Portuguese producer of electricity is presently incrementing energy production in some old hydropower dams by installing new production plants. The need for not disrupting production during the upgrading works causes some concerns related with vibrations induced to the production engines. Vibration estimation was performed in two of these dams, constructed in a granite environment, by performing controlled blasts. For each dam site, some vibration transmissivity laws were developed with the fitting process.

Jan 1, 2008

By D Vrkljan, Z Ester

There was no use of emulsion explosive at Croatia till 1997. Several attempts have been done to bear out the economical and technological affordability of applying the emulsion explosive for open pits and to make the contractor familiar with characteristics of emulsion explosive exepiting experimental blasts series at more open pits on different kinds of rocks. Testing the efficiencies of emulsion explosive there has been applied the original method for linear enlargement of burden of Sc.D. Josip Krsnik’s from Mining, Geology & Oil Faculty, University at Zagreb. The method of linear burden’s enlargement, in distinction from other methods concerning these problems, has been carried out in situ, under real exploitation conditions whereas the physical-mechanical rock’s features, geological conditions, bed relations and rocks’ structure influence the blast efficiencies. On such way, by mean of method the precise boring and blast sizes will be reached for each kind of rock and geological structural bed’s conditions referring to specific explosive type. The technical-economical analysis indicates the most favorable explosive type for specific bed.

Jan 1, 1999

By Gary L. Self, Ronnie Daniel

With the advent of large scale blasts utilizing overburden casting techniques, it was imperative that an ultra reliable surface delay system be developed. Shock tube and detonating cord surface delay systems have been hampered by the lack of a reliable easy-touse method of incorporating multiple paths of initiation to each hole. Two new redundant nonelectric delay systems have been developed utilizing multiple signal paths to allow a higher degree of safety and reliability. The first system designed uses a combination of detonating cord and nonelectric shock tube delays to allow multiple delay paths to each hole. The second system incorporates a new all shock tube delay system which allows multiple delay paths while minimizing over-pressure by eliminating detonating cord trunk lines. These two redundant systems have been used in over 500 production blasts without any misfires due to surface cut-offs or detonator malfunctions.

Jan 1, 1989

By Brian W. Stump

The cessation of testing of any nuclear explosive devices in all environments is the goal of the Comprehensive Test Ban Treaty. In order to assure compliance with such a treaty, an international monitoring system has been proposed. This system will include seismic, infrasound, hydroacoustic and radionucleide monitors located throughout the world. The goal of this system is the detection of any nuclear test. In preparation for this treaty, a series of monitoring system tests, focusing primarily on seismic observations, have been undertaken. The most recent of these tests, Group of Scientific Experts Technical Test Three (GSETT-3), provides valuable data for assessing future monitoring systems. During the course of this experiment, seismic events associated with earthquakes, nuclear explosions and mining explosions have been recorded. This presentation will discuss the numbers and types of mining explosions triggering the system, in a particular area. Possible implications for the mining industry will be explored.

Jan 1, 1997

By Joseph A. Meyers

Explosives techniques and technology are constantly evolving and improving, yet basic communication and business skills are not being used regularly. Many potential blasting projects never occur due to simplistic, basic factors, such as a lack of communication. Articulate communication is the key component in the blast approval process, which has changed remarkably from how business was conducted fifty years ago. Imperative to the approval process is communication outlining the safety and benefits of the blasting project.

Feb 1, 2020

By Mark S. Stagg, Stephen A. Rholl

The firing times of millisecond-delayed initiators are random variables that exhibit varying degrees of scatter. This scatter can cause crowding and overlap of adjacent delay periods, which results in adverse effects on safety, fragmentation, and blasting vibrations.

Jan 1, 1988

By Frank Lucca

This paper includes research and investigation into blast design and blast optimization for vibration control in municipal and tight blasting situations, where specifications were extremely stringent. The paper is written for the field blaster to understand and develop blast plans based on field conditions. The paper includes blast design considerations, utilizing seismograph arrays to check and predict vibration results, and problems encountered in vibration monitoring in extremely tight situations (0-20 feet). Blast vibration frequency, acceleration, peak particle velocities, and relative displacement are discussed with effects in the near and far fields and blast designs utilized to stay under limits. The paper also discusses using the latest in technology for blast design to control vibration. Equipment includes 2D and 3D laser profiling systems, digital video, fragmentation analysis, seismograph arrays, and borehole tracking devices. Other topics are discussed such as public relations, working with regulatory personnel, unions, and other project consultants, and the problems associated with municipal blasting situations, such as, flyrock and proximity of other personnel and equipment on the project.

Jan 1, 2004

It has been common practice for many years to predict and control underwater blasting effects on the basis of certain simplified theories related to the pressures generated by underwater detonations. Unfortunately, two of the most commonly applied concepts in many instances do not provide an accurate modeling of typical field conditions nor the potential for damage. One of these concepts is that the damage potential is related directly to the peak pressure generated by an underwater detonation, without regard to the time history of the pressure pulse. This belief has led to the widespread use of air bubble curtains to reduce peak pressures, without considering the effect that air curtains have on the time history of the pressure pulse. At times, this procedure can be unwise. The other concept is based on the premise that pressure pulses in solids (such as rock) will always be transmitted to nearby water bodies in agreement with the theories of the transmission of plane waves across normal (perpendicular) boundaries. In reality, such conditions are quite rare.

Jan 1, 1985

By Ray Heater, Qian Liu, Alan Bauer

The channel effect is a phenomenon that takes place with decoupling explosive charges; an air shock wave propagating ahead of the detonation wave in the annular space around the explosive charge compresses the charge so that the process of detonation is modified and even stopped. For commercial explosives, such as AN/FO slurries and emulsions, the channel effect causes partial detonation under certain conditions. To simulate and evaluate the phenomenon, a hydrodynamic model was developed based on the assumption that the pre-shock wave is produced by Mach reflection at the tube walls. Based on instrumented experimental studies with the above explosives in diameters ranging from 25 to 90 mm in pipe sizes ranging from 35 to 127 mm, it has been possible to demonstrate that a criterion for failure based on a critical impulse concept fits the experimental data well. Critical impulse values for the various explosives tested are presented along with the necessary correlations between charge and borehole diameter required to produce this.

Jan 1, 1988

Fracture Control Blasting is an alternative to pre- and post-splitting or smooth wall blasting. It was developed at the University of Maryland as an attempt to overcome some of the disadvantages that occur with normal blasting practices. There are two main factors that are unique to fracture control blasting. First, it utilizes a notched or grooved borehole to initiate fractures at desired locations and secondly, it employs a very carefully selected charge so as to provide control over borehole pressure. The maximum borehole pressure must be kept between very definite limits in order to obtain initiation of fractures at locations where they are desired and yet not obtain fractures where they are not desired. When coupled with stem induced fracturing, which was developed for oil and gas well stimulation, it has been found that the charge required for fracture control can be as little as 1/40th that required for normal smooth wall blasting. The paper describes the technique of fracture control blasting and gives results of some of the field testing conducted to date.

Jan 1, 1984

By Michael S. Wieland

Underground coal-mine explosives (permissibles) can be substantially degraded by the underground stress waves from the explosion of neighboring borehole charges. This cross-borehole interaction generally yields the worst receptor (impacted) charge performance when the borehole separations are too close. For explosives which recover, the receptor degradation is worst when the delay until firing is small. Except for a poor quality muck pile or unreacted cartridge fragments, degraded charge malfunctions of this type are difficult to detect in coal-mine delay blasting. A simulator which reproduces the underground wave/receptor charge interaction and special underwater donor/receptor tests were utilized to study this transient desensitization problem. Test results revealed reductions in receptor energy output, delayed transitions into detonation, inferior reaction rates, or sympathetic reaction responses from the impaction. Tests on detonators showed reduced tip-strength, abnormal functioning times, or sympathetic firing as a result of transient impaction. The cross-borehole desensitization and sympathetic reaction response problems warrant concern because they are logical mechanisms for raising the risk of hazardous mining conditions, including blown-out shots, flyrock, charge deflagration, and methane/coal dust ignitions.

Jan 1, 1987

By Virgil J. Stachura, Calvin L. Cumerlato

The Bureau of Mines conducted a series of tests to develop a blasting method that would reduce overbreak and rockfall hazards at a limestone quarry in northeastern Wisconsin. Reductions in overbreak were achieved by shortening the main explosive column and reducing the explosive load in shortened stemming zones in shotholes which were to form the highwalls. Two blasthole diameters, 3 and 4 inches, were used with 7 by 7 foot and 9 by 12 foot burdens and spacings respectively. ANFO, Comsol 300, or PowerAN were used in the body of the shots and Gelmax or 40 pct extra dynamite cartridges were used in the reduced load zones. Smoother highwalls were visually apparent, however further analysis by seismic refraction techniques were performed as an aid to studying overbreak within the rock mass.

Jan 1, 1989

By Dale Preece

In the late 1970’s and early 1980’s substantial resources were devoted to research focused on producing oil from the vast oil shale reserves in the western United States. Since the oil is solidified in the pore space of the shale, extracting it in production level quantities presented monumental technical challenges. Major advances were made in the methods used to extract oil from the shale in large quantities. Extraction methods evolved to culminate in the underground in-situ retorting process. In-situ retorting relied on explosive blasting of the shale to fragment the rock and induce sufficient porosity and permeability for a burn front to propagate through the oil shale. That burn front consumes some of the oil and liberates a substantial portion of it (~30%) for collection and further processing. Oil shale retorting is a blasting intensive process where the entire retort is rubblized in one very large, delay timed blast. Retort 7 in Western Colorado consumed 540,857 lb of slurry explosive to rubblized 348,940 tons of oil shale. Current rock blasting fragmentation predictive capabilities have evolved substantially since these retorts were designed and tested. It is the purpose of this study to simulate the explosively induced fragmentation of oil shale using state-of-the-art computer codes and material models and to infer retort design implications for future development.

Jan 1, 2007

By C. Lownds, U. Steiner

In 2008 a paper from the same source describing four actual cases of exposure of electronic detonators to lightning strikes was presented. It was shown that electronic detonators, like other initiation systems, are vulnerable to very close or direct lightning strikes. At the time of submitting this abstract no further incidents with lightning have been experienced. As a result of those original incidents, and in order to understand how the safety devices inside electronic detonators break down, two series of tests have been done, each with 2 detonator designs. In the first series detonators were subjected to capacitor discharges up to 6kV and 1kJ in energy. In the second series the intensity was increased to 800kV and 24kJ in energy. In the second series, more electrical energy was delivered to the detonator assembly than the explosive energy of the detonator. In both series both detonators showed a spectacular ability to resist very high discharge energies. The tests are described in detail with supporting photographs. The data for both pin-to-pin and pin-to-case (more relevant to lightning) are presented and discussed. The mechanism of breakdown of safety devices is now understood better and the learning is being used to design more robust products. This high-voltage testing is relevant in understanding how electronic detonators might initiate as a result of a very close or direct lightning strike 1. Orica

Jan 1, 2009

By T Davids, O J. Jordaan, M D. J Bonneau

As in most other parts of the world, the surface coal mining industry in South Africa is introducing emulsion explosives as the primary bulk blasting agent for use in wet borehole conditions where AN/FO cannot be used. Most of the emulsion products presently in use are gassed to provide sensitivity. The intimate mix between the fuel and oxidizer in the emulsion has been shown to produce a highly efficient explosive. However, a major difference between emulsion and the previous slurry products is its relatively low physical strength. This prompted Rand Mines' Duvha Opencast Mine, a major South African Escom power colliery, to conduct test work to illustrate the effect of emulsion physical consistency on blasthole loading. This paper presents the results of test work conducted at Duvha to investigate the problems associated with loading both AN/FO and emulsion in water filled holes, stemming emulsion holes, and in particular, to illustrate the difficulty in correctly introducing a stemming deck into the emulsion column. Time dependent behavior of the loaded emulsion holes is investigated. Velocity of detonation measurements for freshly manufactured emulsion, and for emulsion after loading through water with sleep times of up to 10 days, are presented.

Jan 1, 1987

By L. Chaves

In rock blasting, due to numerous factors, both controllable and uncontrollable, the execution rarely meets the planning. The powder factor is an important KPI for blasting since it represents the amount of explosive used to fragment the rock, therefore it depends on the rock mass characteristics and may be influenced by factors such as weathering and drilling quality. The blasts at the Serra Sul mine, S11D project, are usually big blasts and the high productivity is a challenge for maintaining the quality of the whole drill and blast process. It is important to know the contributions of each of the most common influencing factors of the powder factor to direct the efforts to the improvement of the process. A buildup model is presented to evaluate the contributions of five influencing factors to evaluate the planed x executed powder factor. The factors considered in the model are the average hole depth, the amount of hole/blasted volume, the stemming and decking length, the linear charge weight, and the density of the explosive used. The build-up may be applied for both individual blasts and for overall view of the blasts in a period. A case study is presented with the application of the model for the monthly powder factor analysis at Serra Sul mine has contributed to direct efforts to enhance drilling quality and preservation of the drilled holes.

Jan 1, 2024