Search Documents

By S. Mitra1

"This study aims to investigate coarse particle detachment mechanisms (particle diameter > 150 ?m) utilising both experimental and numerical technique. Two mechanisms were studied – (i) interactions of bubbleparticle (BP) aggregate with vortices and (ii) coalescence of bubble-particle aggregates. On the first mechanism, interaction behaviour of coherent vortex structures with a BP aggregate (bubble diameter db = 3 mm, particle diameter dp = 0.3 mm) was studied using a CFD model in the Reynolds number range of 100 to 1000. Effect of surface hydrophobicity on the BP stability was examined using a range of contact angle boundary conditions. To address the second mechanism, interactions of bubble-particle aggregate (db ~ 4 mm, dp ~ 0.4 mm) with both free gas-liquid interface and individual bubbles were investigated using high speed imaging. Both rebound and coalescence outcomes were observed to be responsible for BP instability leading to particle detachment.INTRODUCTIONIt is widely known that flotation process performs excellent mineral recovery for base metal ore particles that are typically in the range of ~ 20 to 150 µm in diameter (Jameson, 2010). More specifically, higher recoveries are usually reported for particles in the size range of ~20 to 70 µm while outside this spectrum, generally the recovery diminishes significantly. It would be highly desirable to improve the recovery of particles at the coarse end of the flotation size range spectrum which has significant economic benefit (Jameson, 2010). However, it is essential that insights to particle detachment phenomenon, the primary impediment in coarse particle flotation caused by the underlying hydrodynamic factors are first obtained at a greater depth.In an ideal quiescent liquid medium, due to inertia, coarse particles deviate substantially from the fluid streamlines and collision efficiency with bubbles decreases which can only be augmented by increasing turbulence level in the medium sufficiently to make random physical contacts with bubbles. Nonetheless, even if successful contacts are made, it is difficult for these large particles to remain attached to bubbles in a turbulent shear flow environment. There are two major mechanisms postulated for particle detachment – interaction of turbulent flow structures (eddies) with BP aggregate and coalescence among surrounding aggregates. Earlier work of Schulze (1982) theorised a vortex acceleration component to characterise turbulence effect on BP aggregate instability in flotation machines. Wang et al. (2015) investigated bubble detachment behaviour from a stationary particle in a nearly homogeneous and isotropic flow field. Using PIV (particle image velocimetry), it was shown that the local maximum energy dissipation rate for the case of bubble detachment was significantly higher than the no detachment case, and was also higher than the critical value for bubble detachment calculated using Schulze’ theory (Schulze, 1982). Later, Wang et al. (2017) also visualised the BP aggregate instability in a cavity flow leading to particle detachment which was attributed to bubble coalescence, bubble surface oscillation and particle deceleration phenomena."

Jan 1, 2018

By Markus A. Reuter, Joep Verwoerd, Marc J. A. Pijnenborg, Yongxiang Yang

"Incineration is a proven disposal technology for all waste materials with heat release potentials, and provides high degree of toxic destruction and control for a broad range of hazardous materials. In the Netherlands, all the hazardous wastes are processed at AVR-Chemie located at the Rotterdam harbour, through rotary kiln incinerators. The newly enforced regulations from the European Union with stricter emission levels require a better understanding of the incineration process and improved process control. However, the transport phenomena and combustion processes within the kiln system are very complex and not well understood. In order to get better understanding of the incineration process, research has been carried out to study the fluid flow and combustion behaviour of the incineration system. Computational Fluid-dynamics (CFD) was used to simulate the gas flow and waste combustion process, and temperature measurements of the operating rotary kiln incinerator were conducted to validate the CFD model. This paper will present the latest results from the current research project for simulating gas flow and combustion heat transfer for a wide range of hazardous waste streams.The simulation of the waste incineration process was carried out using a general-purpose CFD code Phoenics. The rotary kiln and the secondary combustion chamber (SCC), with a waste processing capacity of 50,000 ton/y and an energy input of 30 – 40 MW, is translated into a CFD model. The model includes a k-e turbulence model and a global gas-phase combustion model (3-gas or 7-gas combustion model). The 3- gas model (Simple Chemically-Reacting System, SCRS) predicts only the thermal effect of the fuel combustion, and only one global fuel is used, therefore, real chemical species are not taken into account. In the 7-gas combustion model, (an Extended SCRS, ESCRS), different forms of waste fed into the incinerator have been modelled into a mixture of a general hydrocarbon fuel C3H4 and other components such as CO, CO2 and H2O. Thus, all the incoming fuel streams with different compositions and calorific values can be properly converted into separate inlets. The combustion of the waste is assumed to take place only in gas phase in two steps: (1) primary combustion of the main fuel component C3H4 to form CO and H2, (2) secondary combustion of CO and H2O to form CO2 and H2O. The rate of each combustion reaction is assumed to be controlled by turbulent mixing of fuel and oxidant (air or oxygen), i.e. the Eddy-Break-up (EBU) model. The resulted temperature field was validated with temperature measurement data, and the simulated temperature distribution from both 3-gas and 7-gas model have reasonable agreement with the measured data."

Jan 1, 2003

By J. B. Yianatos

A practical an interactive model to describe the operation of a flotation bank of mechanical cells was developed based on the hydrodynamic and metallurgical characterization of large industrial flotation cells. Thus, the mineral grade and recovery, as well as the stream properties along the flotation bank can be described in terms of the operating variables. The model was built considering the flotation bank as a distributed system, so the solution for the water and solids mass balances, per size classes, for each single cell, are sequentially solved. Also, each cell was described by two distinct zones, the collection zone characterized by the flotation rate constant and the froth zone characterized by the froth recovery. The mineral feed was described in terms of the mineral species and particle size classes, using a rectangular flotation rate constant distribution. Also, the effect of changing the actual operating variables (air flowrate, pulp level, pulp density, pulp flowrate, etc.) on the mineral collection process, in the collection (pulp) zone, was considered downstream along the bank. The froth recovery of floatable mineral has been estimated by measuring the mass flowrate of particles entering the froth by true flotation together with the concentrate mass flowrate (ton/h). The mass flowrate of collected particles at the pulp/froth interface level was calculated from direct measurement of bubble load (ton/m3) and gas flowrate (m3/h). Flotation recovery is mainly related to the froth depth and air flowrate. All parameters considered in the model have been adjusted from direct measurements in plant site. Also, the effects of other operating variables such as reagents dosage, top of froth grade, or froth discharge velocity are presently under study. This procedure has been tested using data from industrial rougher operations consisting of flotation banks with 5 cells to 9 cells in series, and different cell sizes, such as 45m3, 130m3, 160m3 and 250m3. Thus, it has been shown that the model approach is a powerful tool for flotation cells diagnosis, operation and development of new control strategies, as well as, to evaluate the effect that de-sign and operating variables have upon the collection and froth zones performance in large flotation cells.

Jan 1, 2014

By M. M. Yahyaei

The Sarcheshmeh new concentration plant uses a 32 ft×16 ft constant speed (10.5 RPM) SAG mill with two 5500 hp motors which could rotate in two directions. The mill liners are chrome-molybdenum steel casting type with a Brinnell hardness between 325 and 375 with the lifter face angle of 14° and lifter height of 152 mm. The shell liner consists of 120 (two 60 rows) pieces with a High-High configuration in a rail design. A specially designed liner wear profile measuring device enabled fast and accurate measurements inside the mill during the mill shut-down periods. The measurements indicated that the liner wear profile along the liner length is non-uniform and the highest wear occurs between 1.25m and 2.75m of the mill length. The average weight of liners at the time of removal was 47% of the original weight indicating a significant metal loss. The modification of liner shape was undertaken with the aim of having a uniform profile at the liner removal time. The proposed liner unlike the pervious type did not have a uniform shape with a lifter height of 187mm at the section where the wear rate was high. It was believed that this new profile could arrive at a uniform profile at the liner change out time. A study was also directed to the possible change of charge motion due to the liner profile modification. The dynamic behaviour of charge was investigated through the analysis of forces acting on a single ball using mill characteristics such as mill diameter, rotational speed, lifter height and release angle. The simulation of charge motion with this method and Milltraj TM software indicated that the impact position of charge will change only one degree due to the maximum increase of 35 mm in the lifter height. This assured that the installation of the modified liner would not have any adverse effect on the mill because of ball impacting the mill shell. It was predicated that the amount of scrap metal will reduce to 30% from the current value of 47% beside 1500 h increase in the liner life time.

Jan 1, 2014

By Çisem Tuba, Ismail Girgin

"Comparative atmospheric H2SO4 and H2SO4 + H2O2 leaching experiments were performed using a Turkish lateritic nickel ore containing 1.52% Ni. In the leaching tests; acid concentration, temperature and leaching time were considered as main variables and the dissolution behaviour of the ore were studied by Ni, Fe, Co and Mg analyses. The dissolution values in the H2SO4 leaching experiments were observed to increase up to 60% (w/w) acid concentration and a temperature of 95°C. Increase of H2SO4 concentration above 60% at 95°C caused decreases in all the dissolution values and this was attributed to the formation of Fe2(SO4)3 and Fe2(SO4)3•HSO4•H2O type compounds. At the considered optimum H2SO4 leaching conditions ([H2SO4]= 45%, T=95°C, t=45 min); dissolution values reached for Mg, Ni, Fe and Co were determined as 99.12%, 95.58%, 92.63% and 78.37%, respectively. An activation energy of 30.57 kJ/mole was determined for nickel dissolution from the evaluation of the kinetic data obtained for H2SO4 leaching showing that the dissolution was controlled by external diffusion and chemical reactions. Caro’s acid solutions were prepared at H2SO4/H2O2 mole ratio of 3 for varying initial H2SO4 concentrations and leaching tests were performed at 25°C. Co behaved very differently and a dissolution value of 83.94% was obtained even at 5% acid concentration in 60 minutes reaction time. Complete dissolution of Co was obtained after 30 minutes of reaction time at 60% initial H2SO4 concentration and the corresponding dissolution values for Mg, Ni, and Fe were reached to 96.16%, 94.27% and 89.46%, respectively. Although the H2SO4 + H2O2 leaching experiments were conducted at 25°C, it was realized that the temperature of the leaching medium was increased to 122°C after four minutes of reaction time due to probable exothermic reaction(s) at 60% initial acid concentration."

Jan 1, 2014

By Xing Yang, Zhen Peng, Guangwen Zhang, Haifeng Wang, Yaqun He

"Triboelectric separation of ilmenite ore based on the tribocharge differences between ilmenite and gangue minerals was conducted in this study. Triboelectric characteristics of ilmenite and its associated minerals were studied using polyvinyl chloride (PVC), pentatricopeptide repeats (PPR), copper, polymethyl methacrylate (PMMA), stainless steel (SS), teflon and quartz glass (QG) tribochargers in lab triboelectric unit. Results demonstrated that the ilmenite particles tribocharged positively while gangue minerals tribocharged negatively using PVC as tribocharger. The particle size also has a significant effect on tribocharge, and the -0.125+0.074 mm is the optimal size fraction of triboelectric separation. Charge-mass ratios of minerals increase with the increases of tribocharging length, but the increasing rate gradually reduce. At 1.5 m tribocharging length, charge-mass ratios of ilmenite, quartz, feldspar and mica are up to 6.07 nC/g, -6.05 nC/g, -4.30 nC/g and -4.56 nC/g, respectively. Based on the triboelectric characteristics of each mineral, triboelectric separation of ilmenite was conducted, and the grade of ilmenite ore increased from 15.47% to 28.40%. INTRODUCTION As a transition metal titanium plays an irreplaceable role in medical, aerospace and materials due to its light weight, high strength and corrosion resistance. Pure titanium dioxide is an excellent white pigment and is widely applied in industries of paint and textile. Ilmenite is the main raw material for titanium industry. For the beneficiation of ilmenite, series methods have been proposed, such as the application of dry magnetic and wet gravity separations to separate the ilmenite from the zircon and rutile. Electrostatic separation is extensively used in the beneficiation of heavy mineral sands for the recovery of rutile, zircon and ilmenite while flotation is used to separate fine ilmenite (Mehdilo et al., 2014; Fan et al., 2014). Compared with flotation and gravity separation, electrostatic separation does not consume water, and native properties of materials will not be changed and energy consumption will be reduced (Wang et al., 2014). Thus, the wide application of electrostatic separation and other dry separation methods is a trend in separation and purification industry, especially in water-scarce areas."

Jan 1, 2018

By Eduard Stefanescu, James M. Mwase, Egon Sehner, Stoyan Gaydardzhiev

"The study is focused on investigating the production of synthetic rutile of 95% purity or higher from a Norwegian ilmenite ore concentrate. This was to be achieved using a sequential process involving oxidative-reductive roasting at 975°C, followed by magnetic separation to further concentrate the sample and finally leaching with 20% HCl to remove mostly Fe-based impurities leaving behind synthetic rutile. The key process parameters considered were roasting time (1 and 2 hrs), leaching temperature (100, 125 and 145°C), pulp density (15 and 25wt%) and leaching time (3 and 6 hrs). The option of directly leaching the concentrate without pre-treatment was also evaluated. Test work was conducted using samples screened to a size fraction of 105-212 µm. Samples were leached in a 1 L glass autoclave. The reactor was hermetically sealed and thus the resulting pressure was not controlled but was dependent on the process temperature. The product from leaching was calcined and analysed via XRD and SEM to determine the purity of the product. The magnetic separation step was found to be ineffective and discontinued early in the study. Thus far a product with 97% synthetic rutile purity as analysed by SEM has been produced by directly leaching the concentrate at a temperature of 145°C, pulp density of 25wt% and leaching time of 6 hrs.INTRODUCTION The study investigates the use of a process route comprising oxidative-reductive roasting, followed by magnetic separation and then hydrochloric acid leaching and calcination to produce synthetic rutile from ilmenite concentrate. The grade of synthetic rutile produced should be suitable for chlorination to produce pigment grade TiO2. Hence the proposed process should produce a product consisting of no less than 95% synthetic rutile. Additionally, the product should have no more than 1.5wt% combined content of CaO and MgO (Zhang et al., 2011) as they tend to form high-boiling-point chloride leading to the malfunctioning of fluidized bed chlorinator (Cardarelli, 2008). Finally the product should have no more than 2.1wt% of Fe2O3."

Jan 1, 2018

By M. Paymardi, A. Foroutan, T. P. Oladele, M. Abbaszadeh

"Reducing the amount of zinc and iron in lead concentrate is one of the important aspects of processing in lead and zinc flotation plants which results in improvement of lead concentrate quality and prevents zinc loss. In mineral flotation industries, lignin sulfonates are known for their depressant properties for both non-metallic and sulfide minerals such as pyrite and pyrrhotite.This paper investigates the effect of lignin sulfonate on flotation of galena, sphalerite and pyrite in sulfidic lead and zinc bearing ores. Batch flotation tests were carried out on a high pre-activated zinc samples. The feed contains 0.9% lead, 2.3% zinc and 7.5% iron. The dosage of all reagents such as sodium cyanide, zinc sulfate, ethyl xanthate and methyl isobutyl carbinol (MIBC) were kept constant for lead flotation step except calcium lignin sulfonate (CLS) that was varied between 0 and 80 gr/ton.Results for lead rougher concentrate showed that the grade of lead increased by 2.7% while the recovery decreased around 4 % at the highest dosage of CLS. Furthermore, zinc recovery decreased by 6.3% with no significant change in grade. Iron recovery in lead rougher concentrate decreased by 2.3 % while the grade changed around 1%. In sphalerite flotation step, CLS dosage was changed in the range of 0 to 80 gr/ton while the dosage of other reagents such as copper sulfate, lime, amil xanthate and MIBC were kept constant. In this step, no decreasing in grade and recovery of zinc was observed, while iron recovery decreased. It was suggested that CLS has a depression effect on sphalerite in conjunction with other zinc depressants such as zinc sulfate and sodium cyanide. CLS was further used in plant with non-pre-activated zinc minerals. Similar trends were observed in plant.INTRODUCTIONlead-zinc sulfide minerals play an important role in the production of lead and zinc metals in the mineral processing industry (Luo, Feng et al. 2016). Due to complexity of the lead-zinc ores mineralogy, in some situations, their flotation properties vary significantly from one deposit to another one even in itself (Bulatovic 2007)."

Jan 1, 2018

By Lokesh K. Thakur, Peter Radziszewski

"For the cases tested (11 mills with 15 operating conditions), the Bond abrasion test steel media wear rate prediction gives an overall error of 73% and a standard deviation of 192.5%. However, total steel media wear in a given mill (ball or SAG) grinding process is a product of three recognised wear mechanisms -- impact, abrasion, and corrosion. A total media wear model can be defined on the assumption that the effect of each wear mechanism can be independently determined which allows for a total media wear model to be defined as the summation of the wear result of each mechanism (eqn. 1). It is assumed that impact and abrasive media wear is a function of the energy dissipated in impact and abrasion as estimated by a DEM charge motion simulation. Corrosive media wear is assumed to be a function of the media surface area present in a mill.The 3 initial tests developed (steel abrasion wheel, corrosion batch mill, impact chamber) coupled with the impact and abrasion energy spectra from a DEM charge motion simulation produced total steel wear rate results for the same cases as the Bond abrasion test giving an overall error of 0% and a standard deviation of 66.1%. However, if one were to consider the general observation that wear is proportional to energy and maintain the assumption that corrosion is proportional to media surface area then one would realize that the total media wear eqn. (1) can be reduced to eqn. (2). As this is a linear equation and one has, for the same mill, media wear and operating data for three different operating cases, one obtains three equations with three unknowns. This defines a simple matrix manipulation to determine the constants k1, k2 and k3. From the previous data set, we had 6 identical mills grinding the same ore but having different worn liner profiles and charge volume which provided the opportunity to average out the ki values over 20 combinations of 3 cases. With the determined ki values, it was possible to determine a second estimate of the contributions of impact, abrasion and corrosion to total media wear giving an overall error of 0% and a standard deviation of 56%."

Jan 1, 2003

By A. D. Shuloyakov, G. A. Finkelstein, V. I. Kurets, A. K. Vedin

"In disintegrating solid ores with mineral values disseminated in them, one of the principal tasks is to selectively separate valuable mineral particles from the matrix in which they reside, striving at the same time to keep their natural shape and size as intact as possible.The conventional mechanical disintegration methods do not meet this most important requirement in full. The other major objective here is to reduce electric power consumption during the fragmentation stage, since up to 65 per cent of the total power consumption at concentrators processing ores of non-ferrous, ferrous, rare, and precious metals is spent on disintegration steps.Numerous experiments conducted on dozens of ore types (tin, tungsten, and many others, as well as on rock containing diamonds, rubies, emeralds, etc.) have invariably demonstrated by far superior integrity of mineral values as compared with that obtained by mechanical as well as other types of disintegration.However, the process remains as power-intensive as ever which is due to the imperfect nature of the electro-technical devices that convert the network electric current into high-voltage electric impulses responsible for the disintegration process.The maximum capacity attained in disintegrating the hardest materials from 40 mm to 2 mm size in a single operating chamber with four high-voltage electrodes does not exceed 1.0-1.5 t/h. Attempts at increasing the number of electrodes and the capacity of the operating chamber have failed so far because of high overall dimensions and mass of the electrical part of the installation supplying the chamber with pulsating current, as well as of the commutation requirements. At the same time, a number of overseas operations have reported a significant breakthrough in their attempts to reduce dozens of times the overall dimensions and mass of the discharge impulse generating installation (EIS), which enables us to contemplate to increase the capacity of the EIS at least ten times in the nearest future. Yet, even with the currently achieved capacity of the EIS, these installations have found wide use in geological surveying, precious and semi-precious stones production, in grinding super hard materials, etc., since they provide spectacular selectivity of disintegration and thus the integrity of valuable mineral crystals."

Jan 1, 2003

By John A. Rumball, Martin R. Houchin

"For gold leaching of oxide ores, the optimum cyanide : oxygen ratio is approximately 106 mg/L NaCN : 10 mg/L O2 (6.9:1 by mole). In sulphide ores, galvanic coupling of the gold with the electrically conductive sulphides significantly increases this ratio such that leaching may occur in a relatively low dissolved oxygen (DO) environment.RESULTS AND DISCUSSIONGold leaching in a carbon in pulp (CIP) and carbon in leach (CIL) circuit is driven by the supply of cyanide and oxygen, as described by Elsner’s equation (1):• 4Au + 8CN- + O2 + 2H2O ? 4Au(CN)2 - + 4OH- (1)Equation 1 suggests that the ideal molar cyanide : oxygen ratio should be 8:1, or 122.5 mg/L NaCN to 10 mg/L of DO. It is generally accepted however, that oxygen is not completely reduced to hydroxide at the gold surface, and that equation (2) better represents the gold leaching reaction (Marsden and House, 1992):• 4Au + 8CN- + 2O2 + H2O ? 4Au(CN)2 - + 2OH- + H2O2 (2)Additionally, since gold leaching is limited by either the diffusion of cyanide or oxygen to the gold surface (Habashi, 1993), then the relative diffusion rates of cyanide and oxygen must also be taken into account. Marsden and House (1992) suggest that the ideal molar cyanide : oxygen ratio is 6:1, while a more recent investigation using laboratory and plant observations (Heath and Rumball, 1998) suggested a molar ratio of 6.9:1.In practice, although a cyanide : oxygen mole ratio of 6.9:1 applies to some circuits, there are many instances when this is not the case.In sulphide ores, galvanic coupling of the gold with the electrically conductive sulphides significantly increases this ratio. Galvanically connected sulphides, and possibly carbon, provide a large surface area for oxygen reduction. As the cathode surface area increases, the oxygen concentration required to sustain the same rate of gold oxidation decreases proportionately.Galvanically connected particles may be composite particles, however they may simply be liberated sulphides in the same suspension as the gold. Particle collisions within a slurry are sufficient to provide momentary galvanic connection (Greet, 1995)."

Jan 1, 2003

By Alexey P. Tatarinov

Under modern economic conditions in Russia, gold heap leaching is the most effective way of investing into gold-mining industry. Gold is recoverable from small-size deposits, low-grade ores from oxidation zone, cut-off grades, and overburden rocks using heap leaching. This technology is cost-effective and allows a saleable metal to be obtained within the first year of operation. The investments for heap leaching are lower than those of for a traditional plant technology. Production cost per one gram of Au is 5-7 times lower than that of during a plant flow sheet. A seasonal development of mines can be possible. With reference to this, heap leaching resembles the technology of placer deposits development. One of the major advantages of heap leaching is the form of the product. Gold can be obtained as dissolved in a clarified PLS, which allows the further quick treatment. The amenability of ores to heap leaching depends on their mineralogical composition. Oxidized porous ores with a good access of a lixiviant to valuable particles can be treated without pre-crushing. Clayish minerals are often found in oxidized ores with free gold. In order to build ground for heap, several major methods combined with various pad materials are used. These methods have been used at many plants and are reliable. The development of heap leaching technology for gold ores for the deposits from Yakutia, Zabaikalsky region, Primorye region, Uzbekistan, Tadjikistan, and Kazakhstan began in the 70s. However, it has been commercially used only since 1990. The first heap leach plants were built and commissioned in the USSR in 1991 at Vassilkovsloye deposit (Kazakhstan) and at Maiskoye deposit in Russia in 1994. Pilot plant testing was conducted in 1996 using ores from Kuranakh ore field, deposits Phiskulturnaya-Kholodnaya and Lopukhovskoye from the Aldan region. After the first successful commissioning of heap leaching plant in Russia, this technology has been commercially applied for deposits. Every year 1-2 heap-leaching plants were commissioned. More than 30 heap-leaching plants have been commissioned both in Russia and in the former Soviet Union using technologies developed by IRGIREDMET. Keywords: cyanide leaching, heap leaching, ore, percolation, solutions, lime technology

Sep 1, 2012

By Glasswell K. Nkonde, Fredrick Chileshe, Steven Simukanga

Improving food security by increasing crop output is a primary objective for most countries in the sub- Saharan region. Most soils in the region are deficient in phosphorus an important nutrient after nitrogen in plant growth. Phosphates are therefore used together with nitrogen and potassium based fertilizers in improving crop production. Zambia like many other countries in the sub-Saharan region imports phosphate fertilizers for use by its farmers. However, indigenous phosphate deposits of igneous origin exist in Zambia of which the main ones are Chilembwe in Petauke district, Mumbwa sugarloaf in Mumbwa district, and Nkombwa Hill in Isoka district. If commercially exploited, these deposits could become a ready source of inexpensive phosphate for the local farming communities in the country. Previous research has shown that partially acidulated phosphate rock (PAPR) produced using Chilembwe phosphate rock is just as agronomically effective as the imported superphosphate fertilizers on food crops in most of the Zambian soils. PAPR is produced by reacting finely ground phosphate rock with only a fraction (usually 50%) of the stoichiometric quantity of the sulphuric acid required to fully convert the apatite in the rock to monocalcium phosphate thus making the process cheaper in terms of acid consumption than the poduction of single superphosphate where the apatite in the rock has to be fully converted to monocalcium phophate. The factors that affect the percentage of available P2O5 in the PAPR produced include particle size of phosphate rock, degree of acidulation, concentration of acid, process temperature profile, residence time and drying temperature. These factors were studied in a 25kg/hr PAPR pilot-plant in the School of Mines at the University of Zambia using Chilembwe phosphate rock. The PAPR pilot-plant consisted of a rotary drum granulator as the main reactor, a rotary drum dryer and a triple deck vibrating screen. Ground phosphate rock was reacted with sulphuric acid and water in the granulator to form a granular product which entered the drier. The dry product was screened into three size fractions. The 1 – 4 mm size fraction was the final product whilst the –1mm size fraction was recycled. The +4mm size fraction was sent to a crusher while the crushed PAPR was sent back to the screens.

Jan 1, 2003

By Sanggono Adisasmito

"The quality of the higher education in Indonesia is being improved by implementing a program financed by the World Bank under a project named QUE (Quality for Undergraduate Education). The investments are provided to selected study programs through a competitive selection process. The grant finances staff development, the purchase of equipments, textbooks, consumables, technical assistance, and incentives for outstanding faculties such as teaching grants, project grants, lecture note awards, and educational policy studies. These additional investments are provided to produce chemical engineering graduates that will compete beyond the national market.Chemical Engineering Department of Institut Teknologi Bandung in Indonesia has been selected to receive the QUE grant beginning the year 2000 and ending the year 2004. The department is actively involved in the mineral processing issues, particularly in the aspects of energy supply and the environmental protection. The activities are distributed in different laboratories and areas of expertise, such as: thermodynamics and utility systems, process equipment, chemical reaction and catalysis, microbiology and bioprocess engineering, process control, ceramics, as well as polymer and membrane technology. The main objectives of the QUE project are to improve the undergraduate program in the following aspects: Relevance, Academic atmosphere, Institutional management and commitment, Sustainability, as well as Efficiency and productivity, or abbreviated as RAISE. At the end of every fiscal year, the progress of the program is evaluated to measure the effectiveness of the project.The achievement of the QUE project objectives were assessed using performance indicators developed during the program design. There are six indicators to measure the performance of the individual program of study, such as: (1) Admission Test score, (2) average students' Grade Point Average (GPA), (3) average graduates' length of study, (4) graduates' waiting time before getting first job, (5) Test of English as Foreign Language (TOEFL) score, (6) Graduate Record Examination (GRE) score. Essentially, the RAISE evaluation criteria will be used to perform three main functions, such as (1) to measure the achievement through the six quantitative performance indicators, (2) to support the progress of evaluation and reporting throughout the implementation of the program, (3) to provide a universal framework for qualitative evaluation."

Jan 1, 2003

By Vladimir Grujic, Milorad Grujic, Ivan Djurkovic, William Riggs

"In this paper, we have studied efficiency of different chemical structures of frothers on copper ore Majdanpek. The goal was to find out the best suitable chemical structure, which allows good bubble formation, size and interaction, forces on mineral surface. The particle size distribution was between 10 and 100 µm. Our research was oriented on three groups of frothers: alcohols, poly glycol ethers and poly glycols.We also used different collectors based on similar or less similar alcohol group in chemical structure as in frothers, expecting higher stability of air bubble in contact with copper minerals. Minimal potential energy was determinate in the hydrodynamic conditions for different particle sizes. It was founded that it is proportional to air bubble volume on 0.88° and contra proportional to the kinematics viscosity of pulp.Analyzing the results, we find out that poly glycols decreased surface tension the most. Also, it increased amount of coarser particles to the top of pulp. This group is less sensitive to pH value compared to the others too.From the class of frothers with higher efficiency in flotation process, we pointed OrePrep X-75 and X-133 as frothers with expressive frothing characteristic in the alkaline and low alkaline circuits. Special suitability of those frothers for floating copper minerals makes their hetero polar molecules with more than one hydrocarbon radicals connected to one polar group. However, those froters have no nether high or low solubility and are non-ionization. Those froters indicate some small collecting characteristics too. In dispersion systems, those two frothers make two types of bubbles: smaller di < 1.2 mm; V = 0.0008 cm3 and middle di < 16 mm; V = 2.2 cm3 (di – Bubble diameter, V – Bubble volume). Transportation speed of air bubbles it is possible to calculate based on equation: ?s = 27.5 * di 1.4 cm/s. Distribution of free surfaces for chalcopyrite is average 80% in the class –74µm +10µm and 20% in the class -10µm. If we get all class sizes, we find that recovery (R) depends from the time by equation:"

Jan 1, 2003

By R. Weyhe, B. Friedrich, H. Heegn

"Nickel-metal hydride batteries (Ni-MH) are storers of electrochemical energy, which have a higher specific storage capacity than lead or nickel-cadmium batteries. The demand for Nickel-metal hydride batteries is increasing rapidly since their market launch in the early 1990's. In 1999 the output of cells exceeded 80,000 tons per year (1 billion cells per year). Today there is no suitable and sustainable recycling process to recover nickel, cobalt and rare-earth metals. The discarded batteries are used in the steel industry as alloy material because they contain nickel. Cobalt and rare-earth metals are lost; they are non-recycleable.In a German governmental funded research project, IME Aachen, ACCUREC Mühlheim and UVR-FIA Freiberg are cooperating in processing as well as in creating a feasibility study. The target of this project is the development of a new recycling process for metal recovery from Ni-MH-batteries. The proposed process consists of a combination of mechanical, pyrometallurgical and hydrometallurgical processing steps.After shredding the steel shell, the various fractions of battery materials are carefully separated by mechanical processing. A hammer mill with one rotor with a perforated discharge grid of 20 mm opening, was found to be suitable for crushing the batteries to release the active mass of electrodes for metallurgical processing. The ground material is wet screened at a mesh size of 0.5 mm; thus a fine fraction is obtained with valuable components such as Ni, Co, and RE and an oversized fraction consisting of a mix of iron chips, electrodes grids, plastic chips, paper, and flocculent material of separators. The organic components are avoidable when there is a thermal step at the beginning of processing batteries.The separated fine fraction is smelted in an electric arc furnace. Any pyrometallurgical process relies on a suitable slag system. In this specific case, the process has to allow separation of nickel and cobalt as metal from the rare-earths almost quantitatively, collecting the rare-earths as well as impurities e.g. as oxides. The products are a nickel-cobalt alloy and a slag phase enriched with rare-earth oxides for further treatment to ‘mischmetal’."

Jan 1, 2003

By I. Blayda

The purpose of this work is to study and make comparative analysis of germanium extraction and related valuable components of the sublimates from the burning of domestic power coals (product 1) and germanium sulfide materials, which are a waste of lead-zinc production (product 2), by traditional chemical methods (distillation of germanium in the form of tetrachloride from raw and preliminary burning source) and by microbial bioleaching of sulfur-oxidizing bacteria. The dependence of the germanium extraction by chemical methods from phase composition of the initial raw materials was installed. The germanium tetrachloride extraction from products 1 and 2 were 78.50 and 19.52%, respectively. Such difference in indexes on extraction, is caused by germanium confinement as concomitant trace component to the basic phases to carriers. The share of acid-non-soluble compounds (tetragonal modification GeO2 and silikogermanaties) in the product 1 account for 21.5 % of germanium. Ratio between acid-soluble and acid-not -soluble germanium forms are 19.52 and 80.48 %, respectively, in the product 2. Our experiments have shown, that implementation of restorative firing (with addition of 30-40 % carbon at 1150 0?) of sulfide product 2 considerably impacted on the extraction of germanium tetrachloride (91.76 %) in comparison with its low enough extraction at straight distillation of hydrochloric acid (19.52 %). The results are confirmed by a set of physical methods. The results of processing the same so-called hard phase?s material (product 2) with the help of microorganisms are presented. It Has been established, that selected strains of bacteria are capable of extracting from initial raw materials not only macro components (iron, zinc, lead, manganese, aluminum, nickel), but also micro impurity of rare metals (gallium, germanium, zirconium). It is important that these metals were not extracted by traditional chemical methods (with application of aggressive conditions and heats) independently of the phase composition of the source. Almost complete extractions of germanium in solution using sulfur-oxidizing bacteria take place in the first day of the process independently of the phase composition of the source and the type strain. The results have practical significance and can be the basis for developing a unified biotechnological method of technogenic waste processing with a purpose of their sterilization and detoxification with simultaneous obtaining concentrates of valuable metals. Keywords: germanium, extraction, sublimates, bioleaching, sulfur-oxidizing bacteria.

Sep 1, 2012

By E. V. Bratygin, S. P. Elnikova

"In the article carrying out technique of experiments for estimation of power efficiency of process of crushing in cone crushers «in a layer». The conformity of the granulometric characteristics of the crushed products obtained as a result of the tests, the theoretical equations for the size characteristics, and the choice of the optimal equation for the prediction of the granulometric characteristics of the final products obtained by crushing ""in a layer"". Optimization of granulometric composition of power of crushers working ""in a layer"" is carried out with the purpose of reduction of the electric power consumption at reception of a product of required quality. As a result of the experiments, dependencies are obtained, the relevance and applicability of the crushing process ""in the layer"" for obtaining crushed stone of improved quality is proved. INTRODUCTION A number of equations have been proposed for calculating the breakage energy. These include equations by Kirpichev and Kick, Rittinger and Bond (Bogdanov, Olevsky, 1982). Another equation for calculating the specific breakage work in breakage by impact and in stratum was proposed by Devyatkin (Boiko, 2003). In these equations, the breakage energy is proportional to the particle size raised to some power. In the equation proposed by Devyatkin, the ore piece thickness or the feed average diameter is used. The relationship between energy and breakage can be expressed as an equation (Lynch, 1981; Tikhonov, no. 3, 2008) where k is a coefficient characterizing the energy parameter depending on the strength of the feed, l is size in microns. The Rittinger formula is obtained for n = 2, the Kirpichev-Kick formula for n = 1, the Bond formula for n = 1.5. For n = 3 or higher, the equation describes fine and ultrafine grinding. R. Hookey proposed a formula (Lynch, 1981, Tikhonov, no. 3, 2008), where the size exponent n is substituted by a size function In all of the above equations, a single value of the feed and product size is used; for example, in the Bond equation, size is defined as the particle size of the 20% oversize (P80 and F80). However, a single size value can represent multiple distributions, making that the Bond method inappropriate for determining the size (Lynch, 1981). Describing an equation for estimating the grinding energy will allow to design the electric drive and ore preparation circuit for the given breakage method."

Jan 1, 2018

By J. Seo, W. Kim, I. Bae

"Microcrystalline silica impurities such as quartz and opal-CT commonly associated in bentonite should be controlled and removed as far as possible when bentonite is used as biocompatible raw material because they show sufficient evidence of carcinogenicity. Since opal-CT contained in bentonite in trace amounts cannot be well separated by conventional sedimentation method, in this work, the ultrasound-assisted removal of the impurity was attempted. Irradiating ultrasound into bentonite-water suspension promoted the production of fine montmorillonite particles in the suspension and the production markedly increased when montmorillonite was activated by Na2CO3. Subsequent centrifugation of the suspension made it possible to recover pure montmorillonite particles as an overflow product. Only 16.2 mass % of total solids was recovered as an overflow from the non-activated suspension, whereas 63.5 mass % was recovered from the activated suspension at centrifuging speed of 10000 rpm. Increasing sonicating time enhanced the yield of overflow, however, excessive sonication up to 10 min hindered the purification of montmorillonite. It was observed that the peak reflection of (101) plane of opal-CT in overflow increased as sonicating time increased during prolonged sonication. INTRODUCTION Bentonite consisting predominantly of mineral montmorillonite is clay-rich soft rock generated frequently from the alteration of volcanic ash. Depending on the nature of its genesis, bentonite contains a variety of accessory minerals, which may include mainly quartz, feldspar, opal cristobalite/tridymite (opal-CT), calcite, illite and mica. The presence of these accessory minerals can impact the industrial value of the deposit, reducing its commercial value depending on its applications. Therefore, bentonite is often purified by removing these impurity minerals for special applications where specific properties and characteristics are required (Murray, 1999). Among the special applications, bentonite is often used in the cosmetic and pharmaceutical industry as both excipient and active ingredient in the forms of liquid (suspensions, emulsions), semi-solid (creams, ointments) and solid (powder, capsules and tablets). The basic requirements for bentonite to be used as raw material are pure, microbiological and mineralogical inertness. Physical properties such as swelling volume and gel formation are also important. Particularly, microcrystalline silica polymorphs such as quartz, cristobalite and opal-CT should be controlled and removed as far as possible because they show sufficient evidence of carcinogenicity in humans."

Jan 1, 2018

By Janne Kytökari

Controlling a wide range of minerals processes with single control system is an ordinary way to operate in mines all over the world these days. However the potential of these systems is not yet fully recognized nor utilized. The key issue is to manage the information in a way that enables automating the day-to-day tasks, quality control and safety functions. At the same time it provides means for optimization and constant improvement of processes creating a working environment where the system helps employees to do their key tasks instead of searching, modifying, and transmitting the huge number of information arising every day. The distribution of control system nodes enables the other processes to run heedless of a problem occurring in one of the sub-processes. Also the control room can be in remote location such as in large city removing the need to travel substantially long distances to plant sites every day. When all essential information is brought to the same place there is less risk for a mishap to happen due to information breaks that are often the cause of them. One of the biggest single reasons that result in production losses are break downs of machinery usually caused by normal wear, misuse, incorrect utilization rate etc. For this reason it is important to measure the condition of machines using vibration measurement and diagnostics. By moving from failure or time-based maintenance towards predictive or performance maintenance generates eventually a steady and predictable process but also results in significant long term savings. The mineral process at Talvivaara mine is based on bioheapleaching, whereby metals are leached from ore as a result of bacterial action. Bioleaching is a fairly new technology used in metals recovery. Therefore it is important for the mine to collect and analyze data from different stages of the minerals process. Talvivaara mine?s Metso DNA system has integrated machine condition monitoring and information management. These are not only necessary but also crucial in environmental conditions where the outside temperature can drop below -35°C, where ice and snow dominate the landscape and impact the equipment for four months a year and where distances between equipment can be up to 7.5 kilometers. Keywords: DCS, analyzer, machine condition monitoring, automation, remote communications, optimization, mining, metso DNA, Talvivaara

Sep 1, 2012