Search Documents

By V. Sheikhzadeh, M. Saghaeian, R. Hejazi, M. Zare

High Pressure Grinding Roll (HPGR) plays a major role in increasing specific surface area of iron ore concentrate for producing pellet feed. HPGR grinding mechanism implies that material be compressed between the two rolls, therefore layer of material must be able to resist required pressure for achieving suitable grinding conditions. In this study for determining a simple relationship between material pressure resistance ability and HPGR main design parameters, piston press tests were performed on different iron ore concentrate samples along with HPGR Blaine increasing tests. Piston press tests results showed that by decreasing moisture content, material pressure resistance increased and in constant moisture content this parameter will change based on material specifications. HPGR Blaine increasing tests results showed that by decreasing moisture content, HPGR specific throughput and working gap increased and in constant moisture content this parameter will change based on material specifications. For all of the studied samples at worst condition, we got the results including: HPGR delta gap equal to zero, specific throughput lower than 200 ts/hm3.According to the tests results, HPGR Applicability Index (HAI) can be introduced at four different class types from 1 (weak) to 4 (excellent). This index determines achievable specific throughput and possibility of using HPGR according to material specifications, i.e. for HAI 1-4 the pressure resistance is <90, 90 to<125, 125 to <150 and = 150 bar, respectively. Similarly for HAI 1-4 specific throughput is <200, =200, =220 and =250, respectively. So based on design moisture content, if concentrate HAI is 3 or 4, HPGR is a correct choice. For HAI 2, HPGR can also be used. But for a material with HAI equal to 1, HPGR is not a good solution. As a result in order to apply HPGR for HAI 1, material condition such as moisture or slime content should be decreased.

Jan 1, 2018

By John A. Herbst, Ming Song, Xiangjun Qiu

"It has been known for sometime that as wear occurs in tumbling mills there is an associated change in mill throughput. These changes have traditionally been simplistically, attributed to “mill volume effects”. New high fidelity simulation (HFS) tools (involving DEM, CFD and Breakage models) are now giving new “microscale” insights into the complex interactions that occur between evolving lifter/liner profiles and breakage. An illustration of this analysis is shown in Figure 1 below.Here we see that after a new lining is installed (Region I) the wearing process reduces the liner thickness resulting in a larger power draw and an associated higher throughput until Region II is reached. By this point the lifter height is reduced significantly changing charge motion (less cataracting) the power begins to decline, but the comminution efficiency increases with this type of “calmer” breakage environment therefore the throughput continues to increase. In Region III the lifter is no longer providing the minimum required charge lifting action, the power and the throughput both drop off significantly. In the last two stages the behavior is especially complex because throughput is not linearly related to power since grinding efficiency is changing.The study described here shows that these new HFS tools allow the design of wear part profiles which will maximize mill productivity over the entire life of liner/lifter systems. A simple example of such a design procedure is shown involving the selection of a sinusoidal profile for a 34 ft diameter SAG mill.The paper discusses how the principles exposed in this simple example can be applied to search for an optimal profile in which non-standard modifications are allowed to compensate for throughput or wear shortcomings of standard profiles."

Jan 1, 2003

By Remmerswaal, U. Boin, M. B. G. Castro

"To design sustainable products that can be recycled with high resource efficiency, low environmental impact and economic feasibility, the choice of materials and materials combinations, made in the design stage, is fundamental. The products we design, manufacture and use now will be the resources of the future. Designers are able to select materials for a product according to the many functional requirements they must fulfil. But they have a limited knowledge of the recycling processes and its requirements regarding quality of the secondary material streams. Resource Engineers have to manage the processing of these streams, that are becoming more complex with the increasing variety of materials and decreasing size of components. After mechanical separation of the materials streams resulting from shredding of EOL (endof- life) products, there is always a degree of contamination, from two possible causes:Incomplete liberation: the bonds between different materials combined in a component are not completely destroyed by shredding, resulting in some particles containing two or more materials attached;Separation efficiency: the mechanical separation processes are not able to separate perfectly the many material particles; there are always a number of foreign particles in the recovered streams.Sometimes, those contaminants cannot be removed by the industrial metallurgic recycling processes, and a more serious problem occurs when the contamination levels compromise the recycling of the material stream by lowering its quality (i.e. the properties of the recycled material will be lower due to the contamination). As a consequence, the material must be diluted in virgin raw material and/or used in a less demanding application (downgrading), causing resource depletion and increased energy use, waste production and recycling costs. In order to make the best choice of materials combinations for a product, a systematic approach is necessary, that can close the gap between the knowledge areas of Product Design and Recycling Technology."

Jan 1, 2003

By Dingwu Feng, Jannie S. J. van Deventer

"The effect of ultrasonication on reactions at solid/liquid interfaces was investigated by using an ultrasonic probe in two slurry systems, i.e. cyanidation of a refractory sulphide ore and geopolymerisation of metakaolinite. The surfactant dithiophosphate was used to render the gold bearing sulphide particles hydrophobic, in an attempt to induce the formation of cavitation bubbles directly at the desired surfaces. Oxygen was injected into the cyanidation system to improve the attachment of oxygen bubbles to the hydrophobic sulphide surfaces. Geopolymerisation occurs in highly alkaline solution with waste aluminosilicate oxides and silicates as the reactants. The process of geopolymerisation is believed to involve dissolution of Al-Si oxides from solid particles, diffusion of dissolved Al-Si complex from the solid surface into the gel phase, condensation of gel phase and hardening of the gel phase. It has never been investigated how ultrasonication affects the above steps in synthesising geopolymers, despite a number of papers dealing with sonochemical synthesis of materials. The introduction of power ultrasound into such slurry systems is expected to result in advanced geopolymer materials.In the cyanidation of the pyrite concentrate, the kinetics of gold extraction were significantly enhanced in the presence of ultrasound, due to the prevention of passivation and the enhanced dissolution of sulphides. Cyanide consumption was significantly reduced with ultrasonication, owing to the oxidation of soluble sulphides to sulphate, minimising the cyanide consumption by sulphides. With oxygen injection, ultrasound significantly enhanced the leaching of gold from the pyrite concentrate, as oxygen could enhance the formation of the oxidation radicals by ultrasonic cavitation. In the presence of dithiophosphate, ultrasound further improved gold leaching in the oxygen-aerated system. Dithiophosphate could selectively adsorb at gold host sulphide surfaces, and make the surfaces hydrophobic. As a result, the ultrasonication effectiveness could be enhanced through forming cavitation bubbles directly at the interfaces."

Jan 1, 2003

By Leming Ou, Longsheng Yi, Qiming Feng, Yiping Lu, Qing Shi, Kun Liu, Guofan Zhang, Yanfei Chen

"Three important components of stirred tanks involved in energy consumption, the impellers and baffles, were investigated to intensify the agitation pretreatment on the flotation of nickel ores. Flotation tests revealed that the stirred tanks with two impellers had an advantage over those with one impeller in intensifying agitation pretreatment, and the higher agitation speed led to better flotation performance of nickel ores. Installation and removal of baffles were also employed in the stirred tanks, and flotation tests demonstrated that with baffles, the flotation grade increased significantly. These agitator design improvements were used to demonstrate that the energy supplied to the system significantly influences the flotation recovery and that if the energy consumption of the agitation pretreatment is ideal, flotation efficiency can be improved. Data from full-scale operations backed up these results.INTRODUCTIONThe flotation recovery of nickel-copper sulphide ore at the Western China nickel mine has historically been difficult due to the presence of large amounts of serpentine minerals (Feng, et al., 2012). Many studies reported that serpentine minerals tend to have a positive potential at pH values up to 9.5, while sulphides (such as pentlandite and chalcopyrite) have a low isoelectric point(Feng, et al., 2012). Serpentine minerals can form surface coatings on negatively charged sulphides surface due to electrostatic attraction when they interact with each other, which may also reduce collector adsorption and increase the hydrophilicity of the sulphide particles. In order to improve the flotation of nickel sulphides, sodium hexametaphosphate, sodium silicate, carboxymethyl cellulose (CMC), and other agents are used to disperse serpentine coating from sulphide surfaces in the flotation of the Jinchuan deposit and other nickel ores in China ( Kirjavainen and Heiskanen, 2007; Lu, et al., 2011). However, it is difficult to improve of the sulphide flotation due to the high dosage and the lack of selectivity."

Jan 1, 2018

By Jacques Eksteen, Sharif Jahanshahi, Neill J. Bartie, Shouyi Sun

The gradual increase in Cr2O3 levels of UG-2 ores has become a matter of concern for platinum producers in South Africa due to the formation of chromite spinels in melters. The effect of bulk FeOx/MgO ratio, Cr2O3, temperature and oxygen partial pressure on phase stability and composition in the system FeOx-MgO-SiO2-Cr2O3-Al2O3-CaO has been studied between 1400°C and 1600°C using the drop-quench technique. An increase in temperature was found to result in a decrease in [Fe/Cr]spinel. This effect is shown in Figure 1 for the six slag compositions investigated.

Jan 1, 2003

By C. L. Tang

Parts of the wastewater are reused directly and the rest moderately purified and reused, so the utilization rate of wastewater of the whole processing plant reaches 100 percent. At the same time, beneficiation indicators have been improved stably, and great economic and social benefits have been achieved.

Jan 1, 2014

By P. Han

The preparation technological conditions and regeneration method of two novel granulated adsorbing materials of rectorite/fly ash composite (Material 1) and rectorite/water quenched - slag composite (Material 2) and the use of them to remove heavy metals from copper smelting plant wastewater have been studied. The experimental results showed that under the preparation conditions with the ratio of rectorite to fly ash or water - quenched slag of 1:1, the amount of the additive (Industrial Starch, IS) of 15% (Material 1) or 10% (Material 2), the addition of 50% water, and the calcination temperature of 500? (Material 1) or 400? (Material 2), the efficiency of heavy metal removal with the granulated materials was the best, whereas the ratio of disintegration loss was the lowest. Under the treatment conditions of natural pH, and with the addition of the granulated materials of 0.07g/cm3 (Material 1) or 0.05g/cm3 (Material 2), a reaction time of 60 minutes (Material 1) or 40 minutes (Material 2), and the adsorption temperature of 25?, the efficiency for the granulated materials to remove Cu2+Pb2+Zn2+Cd2+ and Ni2+ from the copper smelting plant wastewater was 98.9, 97.5, 96.7, 90.2, and 79.1, (Material 1) or 98.2, 96.3, 78.6, 86.2, and 64.2, (Material 2), respectively, and the quality indexes of the wastewater after treatment conformed with the first level of integrated wastewater discharge standard (GB8978-1996). When the adsorption of heavy metal ions on the surface attained saturation the granulated materials could be regenerated by washing with 1 mol/L sodium chloride (NaCl) solution and still with quite good heavy metal removal efficiency. The granulated adsorbing materials had the advantages of high efficiency of wastewater treatment, easy method of solid-liquid separation and regeneration, and a broad prospect of applications.

Jan 1, 2014

By Thenepalli Thriveni, Seong-Young Nam, Nam-Il Um

New modern water treatment technologies required for arsenic removal from waste waters contaminated extensively by various background sources from mining, industrial waste, agricultural waste, painting industry and natural geological bed rock system etc. Arsenic is a widely dispersed element in the earth&apos;s crust and exists at an average concentration of approximately 5 mg/kg. Arsenic (As) and heavy metals may be released from the mine wastes to the ground and surface water systems, as well as the geological environment due to their solubility and mobility. This research focuses on the effect of accelerated carbonation process for successful removal of heavy metal arsenic anions from artificial waste water and mining waste waters. This accelerated carbonation process is a simple and novel method with 85 ~ 88% removal efficiency. Carbonation has been studied as a process to further improve immobilization of solidified/stabilized waste and granular waste. After successful removal of arsenic anions from solid mining waste and its potential benefits for producing construction materials. Besides, the industrial and urban management systems are generating bulk solid mining wastes, and most often dumping them in open fields. To prevent the landfilling with mining waste, many efforts are being made for the recycling of different types of mining solid wastes with a view to utilizing them in the production of various construction materials.

Jan 1, 2014

By M. Saghaeian, R. Hejazi, H. Abedini, M. Zare

Water recovery in mineral processing plants is one of the most important subjects because water supply is a critical matter economically and environmentally, especially in desert areas. In this paper, the filtration behaviour of two iron ore tailing sample has been investigated using laboratory scale vacuum and pressure filtration units. These samples including tailing from Sirjan and Zarand concentrate production plants with the d80 of 94 and 41 micron, respectively. The results show that by using vacuum filtration the cake moisture content of Sirjan sample would be about 24%. But the filtration time is too long and vacuum belt filter cannot be used in industrial scale. Adding about 40 g/ton of flocculant would decrease the filtration time by about 30% and make the vacuum belt filter appropriate for dewatering of this sample. For Zarand tailing sample, the vacuum filtration would produce a wet cake by about 31% moisture content. Filtration time is too long and adding flocculant would not improve the results very much. So pressure filtration must be used for dewatering of this sample. The results of laboratory tests show that using pressure filter would reduce the cake moisture content to 21%. The filtration time is logical, so this process can be used for Zarand tailing dewatering.

Jan 1, 2014

By W. Yao, M. L. Li, R. Cui

"The purpose of this research is providing a flotation process for recovery of lead in lead silver residues from a zinc smelting plant with a new hydroximic acid collector (HOC). The collecting ability and reaction mechanisms of HOC were investigated based on pure mineral flotation tests and analysis of zeta potential. The pure anglesite flotation tests showed that HOC has a good collecting ability for anglesite. Zeta potential measurements proved that HOC adsorbed on anglesite surface physically and chemically. The lead-silver residues in a zinc smelting plant with lead grade about 17.5% was used as raw material for flotation tests. The results showed that under the conditions of pH adjusting agent lime 500g/t, inhibitors sodium silicate 2000g/t, collector HOC 1500g/t, frother alcohol oil 75g/t, the grade of the lead concentrate can be reach 47.18% and the recovery was 76.39% by one roughing-one scavenging-three cleaning and middles back to the flow-sheet in turn after the lead-silver residues were washed by two stages of cleaning-filtration.INTRODUCTION Nowadays, with the increasing exploitation of natural mineral resources, more and more secondary resources should be researched and used for the valuable metals. Hydrometallurgical zinc leaching residues, which contain a considerable amount of zinc, lead, silver and other minor valuable constituents, is a typical and abundant secondary resources (Zhang et al., 2011). A huge quantity of zinc leaching residues (ZLR) had been produced per year (Jiang et al., 2017).This residues not only occupy precious land but also threaten the environment because of the dissolved heavy metals especially in rainy days (Han et al., 2014). Consequently, it is urgent to develop an effective and clean method to dispose this residues which can benefit not only in economical but also in environmental (Jha et al., 2001)."

Jan 1, 2018

By Ashish Kumar

High grade ore deposits in the world are fast depleting and the valuables in the low-grade ores are finely disseminated. The feed grade to flotation circuit is also declining. Attainment of suitable grind is preferred, which inevitably creates more fines of the gangue minerals to interfere with the flotation process because of the undue competition between the fines and the valuables for the collector ion adsorption. Besides the use of polymeric or long chain hydrocarbon depressants for the gangue mineral, microbial induced flotation also has potential to float minerals selectively. Thiobacillus ferroxidans and Thiobacillus thiooxidans adhere on the minerals to modify its surface properties and affect the minerals flotation acting as depressants. Hindustan Zinc has conducted laboratory studies to understand the adhesion of microorganism on the mineral surfaces and its impact on the selective flotation. The experiments were further designed to reduce consumption of depressing reagents for graphitic carbon, pyrite, and galena. Preliminary studies reveal that desired quality of concentrate can be achieved with reasonable recovery. Keywords: thiobacillus thioxidans, thiobacillus ferroxidans, bioflotation, microbial induced flotation

Sep 1, 2012

By L. O. Filipov, N. E. Menad, A. Geneyton

"Zeta potential of synthetic monazites presenting various compositions were measured to investigate the effect of the main lanthanides substitutions on electrophoretic mobility and resulting IEP. The measurements are performed in a CO2 depleted and enriched solutions showing both reduced influence of monazite chemistry and strong influence of ions resulting from the solubilization and dissociation of CO2. The influence of oleic acid on the electrophoretic mobility of those monazites was also investigated. The influence of pH on oleate adsorption was studied using a bubble/particle adhesion system. Adhesion strength measurements were performed on pure synthetic monazite-(Ce) and monazite-(La). An extensive thermodynamic model of monazite in water was developed to highlight correlations between lanthanides hydroxides/carbonates species concentrations in the bulk solution and oleate adsorption. Based on electrophoretic measurements, advanced thermodynamic consideration and adhesion measurements, further details of the oleate adsorption model on monazite surface were proposed.INTRODUCTION Electrophoretic and potentiometric data on monazite and, a fortiori, other rare earth semi-soluble salts such as bastnaesite are extremely erratic (Chelgani et al. 2015). The isoelectric points measured with electrophoretic mobility methods range from 4.7 to 6.5 although sporadic data indicates an IEP (isoelectric point) far from that range. Different explanations are proposed in the literature to explain the IEP variability notably the numerous chemical substitutions that frequently occurred within monazite crystal lattice (Chelgani et al. 2015). Based on lanthanides speciation diagram, several authors highlighted the influence of specific lanthanide species on the flotation performance of rare earth semi-soluble salts when carboxylate or hydroxamate collectors are used. Although lanthanides ions have a great affinity for carbonates groups (Kragten et Decnop-Weever 1987), lanthanide (hydrogen) carbonates were not implemented in speciation diagrams. In this work, an advanced thermodynamic model is proposed to highlight correlation between flotation performance and lanthanide species predominance but also concentrations. Qualitative measurement of the monazite surface hydrophobicity are performed through tests of adhesion of coarse monazite particles onto bubbles. Since flotation and microflotation technics are highly influenced by hydrodynamic parameters, this method was investigated to obtain a sharp contrast between appropriate and inappropriate pH conditions. This paper is to investigate 1) the effect of lanthanides substitution on monazite surface properties through zeta potential measurements, 2) the mechanism of adsorption of carboxylates on monazite surfaces and 3) the effect of CO2 on monazite surface properties and carboxylates adsorption."

Jan 1, 2018

By A. Demirag, F. Burat

"The most important metals in the jewelry sector are undoubtedly gold and silver. As a result of workmanship work done in the jewelry industry, the tiny metal and jewel fragments and metallic powders are scattered. Given the prices of gold and silver on the market, the dust that emanates from these workshops is of great importance. Gold recycling has become as important as raw material production within the mass market and gold production industry. In 2016, 29% of the world gold supply has been obtained through recycled gold production. Waste derived from jewelry activity is included in this category, and represents an essential component of this percentage. In the scope of this study, the recovery possibilities of Au and Ag from jewelry sweeps floor sample was investigated using flotation method. In the experiments, optimum pH value, particle size, the effect of dispersant, type and amount of reagent were investigated. As a result of these studies, it was determined that the optimum pH value was 6.5 and the particle size was -212 microns. It was observed that the most suitable reactive combination was Aero 242 and Aerophine 3418A and Na2SiO3 has no positive effect on recovery of Au and Ag as a dispersant agent. As a result of tests, a final concentrate containing 268 ppm Au and 2122 ppm Ag was obtained with 81.4% and 74.5% recovery respectively. INTRODUCTION Because of the softness of pure gold, it is usually alloyed with base metals for use in jewelry, altering its hardness and ductility, melting point, color and other properties. On the other hand, gold has some special chemical properties which in normal conditions, don’t react with water, dry or humid air, oxygen, ozone, nitrogen, hydrogen, fluorine, iodine, sulfur and hydrogen. In these days, gold is used in different sectors like jewelry, electronics, finances and investing, dentistry, medicine, aerospace, awards & status symbols. According to Deutsche Bank Research, the primary usage of gold is jewelry. It has been used to make ornament and jewelry for thousands of years. In this sector craftsmen learned that alloying gold with other metals like copper, platinum and silver to increase gold’s durability. Alloying gold with other metals changes the color of the products. Another significant sector of gold is electronics. Modern electronics want the use of noble metals, like gold, especially in the areas of information processing, telecommunications, and military and space electronics (Habashi, 1997). Electronic devices use very low voltages and currents which are easily interrupted by corrosion or tarnish at the contact points. Gold is the highly efficient conductor that can carry these tiny currents and remain free of corrosion. Electronic components made with gold are highly reliable. Gold is used in connectors, switch and relay contacts, soldered joints and connecting wires. Every sophisticated electronic device have a considerable amount of gold. This includes cell phones, calculators, personal digital assistants, GPS units, and other small electronic devices. Most large electronic appliances such as television sets also contain gold. Humankind has known silver since prehistoric times like gold because silver occurs in native form. The metal is found in the Earth's crust in the pure, free elemental form native, as an alloy with gold and other metals, and in mineral such as argentite. Most silver is produced as a byproduct of copper, gold, lead, and zinc refining. Silver is very soft metal like gold also, it is the highest electrical conductivity, thermal conductivity, and the lowest electrical contact resistance of all metals (Habashi, 1997). Silver is used in different sectors like industry, jewelry, electronics, photography silver good, and coins. The main usage of silver is supplied by electronics. Silver's unsurpassed thermal and electrical conductivity among metals means it cannot easily be replaced by cheaper materials. In addition to silver is using in ener"

Jan 1, 2018

The introduction and subsequent ascendancy of autogenous and semi-autogenous milling for comminution circuits has undoubtedly lead to many economic advantages. From a process viewpoint, however, at least one downside has been the sensitivity of these machines to process input variations. Foremost among these is ore competence, though feed size comes a close second. This sensitivity is due to the reliance of ag/sag mills on the feed ore for their grinding media competence and size. Autogenous (ag) mills are the most sensitive in this respect with semi-autogenous (sag) mills being increasingly less so as the ball charge is increased. Increasingly designers and operators are recognising the importance of feed size and the benefits of manipulating it to improve performance. This has been achieved by installing additional crushing/screening capacity ahead of the ag/sag, better operation of the primary crusher, better control of segregation cased by stockpiles and bins and by changing blast design/practices to modify the ROM size distribution. This paper describes the influence of feed size distribution on ag/sag mill performance with reference to a range of plant data. It particularly concentrates on how changing blasting practice to modify ag/sag feed size can have a considerable overall benefit.

Jan 1, 2003

By Y. C. Liu

Arsenic bearing copper-gold ores deposit have been found in most areas of China, especially in southwest. Due to the very closed association between arsenic, copper and gold, conventional flotation and cyanide leaching process may not give positive results. An arsenic bearing copper-gold ore in Sichuan province ,with gold grade of 10.12 g/t, 0.6% Cu and 0.14% As, is characterized by superfine grains with -40 microns fraction accounting for 70.9% and the gold enwrapped mainly by pyrite and tennanite accounts for 34.31%. Arsenic in this ore occurs in isomorphism, deposited in tetrahedrite. The ore was processed primarily in two stage flotation to get copper bearing gold concentrate and pyrite bearing gold concentrate respectively, and sequentially processed by leaching. Under the pressure of 300 KPa and 110~115 ?, the copper-gold concentrate was leached by an oxidizing and catalyzing leach agent then copper and gold were separated from each other in leach solution. The pyrite bearing gold concentrate was processed by cyanide leaching with the leach residue as sulfur product. The test results showed that copper recovery was up to 88.89%, gold recovery up to 89.18% and sulfur recovery up to 92.64%.

Jan 1, 2014

By Shi Shuaixing Zhang Yuejun, Fan Xuesai Zhangming

"For the traditional principle of flotation cell design, or in the perspective of some researchers, the mixing effect of impeller for flotation cell is not only to suspend the particles off the bottom, but also to mix slurry well to achieve a uniform system. But for some special processing conditions, the depth profile of slurry concentration and particle size demonstrates an obvious difference. In the part around of the impeller in the cell, the slurry concentration is much higher than the part below the lip.For the vanadium titano-magnetite flotation process, distinguished with high concentration and large coarse particle size fraction, even though the concentration is very high, it can reach good gas dispersion, which is a fundamental principle for flotation cell design and application. The gas dispersion is not a challenge in the high slurry concentration environment, not only in the vertical direction, but in the cross section. Different levels (the distance from the lip is 400mm, 700mm, 1200mm, 1700mm, 2200mm, 2700mm) slurry in the flotation cell is sampled and analyzed. The slurry concentration of the 3 levels(1700mm, 2200mm, 2700mm) is about 55%, but the slurry concentration decreases from 55% to 25% sharply towards the lip.Therefore, a new understanding and viewpoint is presented, that the uniform system of slurry is not always reasonable for all of the flotation process. For some special process, if the coarse particles are needed to agitated well and transported to the upper cell, the quiescent zone in the upper cell will be destroyed and enhance the detachment probability for the coarse particles. The difference of slurry concentration and particle size fraction benefits the air dispersion and coarse mineral particles recovery.1.INTRODUCTIONNowadays, flotation is the most widely used separation process in the mineral processing industry. The importance of flotation technology in the global economy is significant. A rough estimate of the quantity of crushed ore treated by flotation is about nine billion tons per year, and the portion of base metals processed using this method is approximately 95% (Brewis, 1996)."

Jan 1, 2018

By F. H. Wang

The Yinmao Lead-Zinc Mine Co. Ltd. has got 50 years of mining history. In recent years, the manganese grade in the flotation tailings has been continuously increasing. In order to make fuller use of the existing resources, as well as to increase the company?s economic efficiency, our company adopted the technique ?magnetic separation? and ?iron removal? to effectively recycle the manganese concentrate resources.

Jan 1, 2014

By S. K. Chaurasiya

o meet the ever increasing demand of iron oxide feed stock for rapidly growing domestic steel industries and to effectively manage the depleting reserve of high grade lumpy iron ore, Pelletization of iron ore fines/slimes are expected to play a dominant role in the near future. Use of pellets will also enable the blast furnace operator to achieve higher levels of productivity with lowering of operating cost. The effective utilization of Iron Ore Slimes is important not only from the point of view of optimum utilization of Iron values in the mined ore but also for preventing environmental pollution. A significant amount of slime is being accumulated at the tailing dam of one of the iron ore mines and with the present scale of operation the tailing dam will be filled in another 10 years. Hence to increase the life of tailing dam and for better utilization of the iron values a study has been carried out for the suitability of pellet manufacturing with slimes and fines at our laboratory. The pelletization studies are aimed for optimization of various parameters for production of Blast furnace/ DR grade pellets from beneficiated slimes and Fines. This paper attempts to describe the production of blast furnace grade pellets from beneficiated slime and fines and its characterizations.

Sep 1, 2012

Rotor speed is one of the key hydrodynamic parameters in froth-flotation and it plays an important role in bubble-particle attachment. Laboratory scale studies for optimizing the rotor speed to achieve maximum flotation rate constant (K) of quartz, ground by ball mill, are. Purity of quartz was 99.4 percent and d80 of ball mill product was 230 µm. Each size fraction was separately subjected to flotation at three different rotor speeds, namely, 1200, 1000 and 800 rpm, and the flotation rate constant was calculated. The results showed that the flotation rate constant was high at the rotor speed of 1200 rpm. The flotation rate constants achieved at 1200 rpm were 8.676, 8.232, 7.818, 7.248, 7.068 and 6.984 min-1forthesize fractions of +300, -300+250, -250+212, -180+150, -150+125 and -125+106 µm, respectively. Keywords: froth flotation, rotor speed, flotation rate constant, ball mill, quartz

Sep 1, 2012