Search Documents

By Graeme Heyes, Warren J. Bruckard, Michael A. Somerville

"A limited series of laboratory batch flotation tests was conducted on a suite of calcium-ferrite-based slags made in laboratory smelting trials. The smelting tests were conducted as part of a wider CSIRO Minerals’ research project aimed at developing a single-stage continuous copper-making process. The objective of the flotation work was to maximise copper recovery and iron rejection from slags made in the process.The slags treated included a reduced low copper slag, an oxidised high copper slag composite, and a very reduced low copper self-pulverising slag. The copper content of the slags varied from 2.9% to 14% Cu. The copper was present as metallic copper, oxide copper and copper-calcium ferrite phases with the phase mix related to smelting conditions. The slags were crushed, ground, wet-screened at 355 or 210 µm to remove coarse metallic particles of copper, and floated at natural pH (about pH 11) using reagents and conditions appropriate for the selective recovery of the copper phases.In rougher/scavenger tests on the reduced low copper and self-pulverising slags copper recoveries above 92% were obtained with copper enrichment ratios varying between 2.3 and 2.9. For the oxidised high copper slag copper recoveries were poorer - only 47% of the copper was recovered with an enrichment ratio of 3.3. The presence of the slow floating copper-ferrite phases in the slags limited further (selective) copper recovery. Ageing of the high copper slag, that is, a significant delay between grinding and flotation, resulted in a deterioration of the copper flotation response.The critical parameter affecting the flotation of copper from direct converting slags was found to be the form of the copper in the slag. Slags containing a higher proportion of the more desirable form of copper for flotation will provide the best opportunity for high copper recoveries to be consistently obtained, allowing improvements in the economics of the overall copper-making process."

Jan 1, 2003

Micro-fine disseminated molybdenite was ground in a laboratory stirred mill using steel media and zirconium media respectively. The floatability of ground molybdenite and slurry chemistry was investigated. It was found that the total recovery of ground molybdenite using zirconium media was higher while the pH and Eh of the slurry are lower than that using steel media. When steel media was used, iron oxy-hydroxides had been generated coated on the surface of molybdenite, and decreased the floatability of molybdenite, especially of the -10µm particles. The iron and lead oxy-hydroxides was generated by the reaction between steel media with pyrite and galena associated with molybdenite. It was also found that changing the grinding media to inert can benefit the flotation of molybdenite. Keywords: stirred mill, grinding environment, floatability, micro-fine disseminated molybdenite, fine grinding

Sep 1, 2012

By Sunil K. Tripathy

Particle characteristics such as size, density, liberation and magnetic susceptibility play vital role in magnetic separation technique. To understand the performance of magnetic separation process for chromite beneficiation industry, particle characteristics need to be analysed. However, to date, this has been an expensive and time consuming task, thus only minimal amounts of this type of data are available in the literature. Several new methods are being developed, that will produce the required mineralogical and liberation data to provide processing information rapidly and inexpensively. Among these, QEMSCAN is a unique and advanced characterisation equipment used for liberation analysis for different ore whereas S.G. Franz Isodynamic Separator for determining the magnetic susceptibility. In Indian chromite deposits, the content of iron bearing minerals in the ore is typical which controls the Cr:Fe ratio in the product while treating in gravity based beneficiation plant. In the present investigation, detailed characterisation of two distinct chromite ore samples from Sukinda chromite deposit, India, was investigated which includes advanced mineral characterisation using QEMSCANand magnetic susceptibility measurement by using Frantz Isodynamic separator, etc.. Presence of haematite and gibbsite along with chromite mineral were identified as major gangue minerals in the high grade ore from XRD pattern whereas Goethite, Quartz, Haematite, Kaolinite, Ringwoodite identified in the low grade ore. The mass magnetic susceptibility of low grade ore is very high 5.2 cm3/g compared to 2.7 cm3/g for high grade ore, due to the presence of abundant quantity of iron bearing minerals. Subsequently, these two types of ore were subjected for magnetic separation for improving Cr:Fe ratio by using different magnetic separators viz. induced roll magnetic separator, wet high intensity magnetic separator, rare earth roll magnetic separator, rare earth drum magnetic separator. The results of magnetic separation studies indicated that, Cr: Fe ratio of the chromite ores can be improved to 3.99 and 1.97 from the feed assaying 3.09 and 1.29 respectively. Studies on rare earth roll magnetic separator indicated that both the ores were upgraded to a maximum Cr:Fe ratio level at optimised condition. Keywords: characterization, QEMSCAN, magnetic separation, rare earth roll magnetic separator, industrial mineral, chromite

Sep 1, 2012

By S. F. Kaplan, A. S. Dolotov, V. N. Kovalev

"The proportion of refractory sulphide ores and concentrates in world gold mining industry is growing every year. Pressure oxidation of these materials (in autoclave) allows to oxidize gold hosting minerals. Traces of halides and pseudohalides present in the slurry liquids contribute to formation of complex gold compounds. Sorption-active carbon present in ores leads to irreversible adsorption of complex gold compounds and their loss. The objective of the research is to study gold extraction dependence on the concentration of chloride-, cyanide- and thiocyanate-ions in the slurry liquids during pressure oxidation. Double refractory flotation concentrate of the Bakyrchik deposit was used for the testwork. The research was planned on the basis of a full factorial experimental design with additional refining experiments. Ligand concentrations (0 – 1000 mg/l Cl-, 0 – 600 mg/l CN-, 0 – 1200 mg/l of SCN-), temperature (200 – 240 °?) and retention time (1 – 6 h) were used as variables of pressure oxidation process. It was determined that sulfide minerals oxidize much faster than ""organic"" carbon. Under the conditions of T = 240 ?C, t = 2 h, sulphide sulfur oxidation was 95.6%, while ""organic"" carbon oxidation was 46.1 %. Each of the examined ligands has a significant adverse impact on gold extraction. Analysis of the experimental data demonstrated that with a high degree of confidence (R2 = 0.883) gold extraction does not depend on the ligand type, but only on its concentration and the ""organic"" carbon oxidation degree. In case of complete oxidation of ""organic"" carbon, the presence of the ligand (L = Cl-, CNS-, CN-) in the liquids at a concentration of up to 20 millimole/L does not significantly affect gold extraction. The assumption that the main factor of preg-robbing in ???-CIL treatment of double refractory concentrates is the natural ""organic"" carbon sorption-active to gold has been confirmed. INTRODUCTION In recent decades, placer gold mining has been gradually declining and hardrock gold mining, including ""refractory"" gold mining, has been growing all over the world, as well as in the Russian Federation (http://www.miningworld.ru, 2015). One of the main reasons why gold ores are refractory is gold adsorption on natural carbonaceous materials (""organic carbon""). Only a few technologies are suitable for processing such ore concentrates (a significant amount of gold is contained in refractory hardrock ore both in Russia and worldwide) (Vorob'yev-Desyatovskiy N.V., Yepifanov A.V., 2014)."

Jan 1, 2018

By Ljubisa Obradovic, Baisui Han, Batnasan Altansukh, Zoran Stevanovic, Atsushi Shibayama, Jonovic Radojka, Daizo Ishiyama, Kazutoshi Hag, Radmila Markovic, Ljiljana Avramovic

This paper discussed a combined froth flotation and high pressure leaching (HPL) process to recover copper from mine tailings. At first, froth flotation were carried out using the mine tailings sample under various conditions in the presence of different pH (3.5-10) and sulfurizing reagent value (0-1000 g/t), respectively. As a result, optimum condition (sulfurizing reagent of 1000 g/t, pH of 10, PAX (collector) of 100 g/t and MIBC (frother) of 200 g/t) was found for froth flotation of copper. The effects of sulphuric acid concentration, leaching temperature, total pressure (steam pressure plus oxygen pressure) on high pressure leaching (HPL) of mine tailing were investigated using sulphuric acid solution in the presence of oxygen. The best conditions for HPL were obtained to be sulphuric acid concentration: 0 mol/L (water), leaching temperature: 170 ?, total pressure: 2 MPa, leaching time: 1 hr and pulp density: 100 g/L. The leaching rate of copper reached nearly 99 % and the concentration of copper in pregnant leach solution (PLS) was 0.24 g/L. Finally, copper in the mine tailing was recovered using froth flotation followed by HPL. As a result of a combined froth flotation and HPL, the vast majority of copper (99 %) from the mine tailings was extracted.

Jan 1, 2014

By Abhilash

Different methods of utilizing refractory bauxite and disposing red mud are practiced throughout the world, but none of them are known to be environmentally innocuous due to the complexity and /or high cost, and none has been found to be feasible on an industrial scale. Under these conditions, the use of bioleaching process seems promising. The present study emphasizes on the isolation of native extremophiles from the source Indian bauxite and red mud, with their detailed cellular and physio-chemical, and biochemical characterization. These organisms were tested for their ability to thrive in physically or geochemically extreme conditions. The gram positive capsule rich mesophiles and thermophiles were tested for removal of gangue minerals from the bauxite and red mud samples. Keywords: refractory bauxite, red mud, extremophiles, bio-beneficiation, gangue

Sep 1, 2012

By A. V. Kanarskay?

The research is aimed at involving in the processing of poor platinummetal natural and technogenic raw materials. The purpose of the research is the creation of a multifactorial complex of innovations in the system of ore preparation and separation cycles, which ensure a high efficiency of flotation enrichment of hard-to-treat raw materials. In the usual practice of enrichment, minerals of the platinum group (PGM) of less than 10 microns in size are the source of inevitable process losses. For poor raw materials, it is precisely thin PGMs that are characteristic, their proportion sometimes being almost 100%, and their opening leads to the formation of a large amount of slime, which adversely affects the efficiency of flotation. To reduce the yield of slimes and increase the selectivity degree of the opening of the PGM in the ore preparation cycle, a dry grinding scheme and pneumoclassification of the milling material has been developed to obtain fractions of different fineness, density and morphology of the particles. From 2 to 5-fold reduction in the yield of slurries for various ores has been achieved. The separation cycle successfully tested are: flotation of fractions in separate cycles with a differentiated choice of the reagent regime; preliminary selective flocculation of slime fraction material; use of a new generation of bioreagents for flocculation and flotation. A new approach to subsoil research is protected by a patent. The dependence of the efficiency of biocollectors on the composition of biomineral extract from the processed raw materials, which forms the basis of new reagents, is established. The possibility of obtaining the degree of extraction of PGM, native gold and sulphides from finely ground pre-fractionated poor ores with the use of biocollectors of at least 85% is proved. With conventional reagents, the extraction of PGM is 12-23% lower, with the use of traditional ore-preparation apparatuses, the PGM recovery rate was halved. Methods for the long-term storage and preparation in industrial conditions of biocollector reagents that do not require the purification of waste waters from them have been developed. The developed multifactorial system of intensification of flotation enrichment can be introduced to recovery PGM from tailings of enrichment of titanomagnetite, chromite and copper-nickel ores.

Jan 1, 2018

By G. Sedelnikova

This paper is aimed to elucidate the problem of copper losses in pyrometallurgical slag. Currently, flotation is used to recover copper from the slag and return the metal into the pyrometallurgical process, but the percentage of recovery frequently remains unacceptable. The process of copper leaching from the slag flotation tailings using biologically regenerated ferric sulfate is considered here as an approach to the issue. A sample of the slag flotation tailings containing 0.67% Cu and 4.99% Zn was supplied by the Urals Mining and Metallurgical Company (UGMK, Russia). The Cu and Zn speciation analysis of the sample demonstrated that Cu occurred as 58.1% oxide, 15.4% native Cu, and 18.1% secondary sulfides whereas chalcopyrite proportion was as low as 8.4%. Prevailing Zn species were refractory (58.9% Zn ferrite), and zinc oxide and silicate species made just 37.2% of the total metal content. The silicate generated silica gel that strongly hampered filtration. As demonstrated, Cu recovery is a possibility, which is apparently not the case with Zn. In this work, the stirred tank bioreactor acid leaching employing bacterial Fe3+ sulfate solutions was studied, with ferric sulfate being a product of Fe2+ biological oxidation and not the chemical reactant adding of Fe3+ sulfate. Acidithiobacillus, Sulfobacillus, and Leptospirillum bacilli were employed in Fe2+ biooxidation. Temperature, pH, Eh, S:L ratio, leaching time, and Fe3+ concentration in the source leachate as the process controls were considered. As demonstrated, the process employing biologically regenerated ferric sulfate proved to be more efficient than conventional chemical leaching. Under the optimum conditions, the proportion of Cu extracted into leachate during 2 hours was 79.1%, and that of Zn 27.2%. Precipitation of high-grade Cu sulfide served to extract the metals from the leachate, and Cu extraction was 99.7%. All in all, 23.2% Cu, 0.03% Zn, and 0.02% Fe was returned into the pyrometallurgical process. Keywords: slag flotation tailings, copper leaching

Sep 1, 2012

By Leon Lorenzen, Victor E. Ross, Anton W. Kleingeld

Key to successful innovation, whether at organization, industry or national level, is the alignment and utilization of resources in the most appropriate and efficient way. Innovation needs to be directed strategically, and it needs to be auditable in a systematic and integrated fashion. In the light of these considerations, this paper describes the construction and use of a topographical map of the innovation landscape. The purpose of the map is to provide a holistic view of the key factors that enable innovation (the so-called ’landmarks’), how well they are aligned to support a particular type/nature of innovation in the organization, and to identify possible gaps. The significance (importance) and height (performance) of the landmarks in supporting and enabling innovation within the organization is determined by means of a selfappraisal audit. The topography of the landscape derived thus is subsequently interpreted in terms of the organization’s particular innovation strategy and environmental context. The application of the Innovation Landscape Methodology is illustrated in a number of organizations within the Mining and Minerals Industry of South Africa. Important observations and conclusions regarding the strategic alignment of enabler strengths within these organizations are made.

Jan 1, 2003

By Yuexin Han

The wet preconcentration of haematite, comminuted by high-pressure grinding roller was studied, using the cylindrical ferromagnetic medium. The effects of various factors including rod diameter, rod gap and background magnetic field intensity (BMFI) on the performances of preconcentration for different size fractions and the force analysis of single mineral particles with different diameter in the separation zone were emphatically investigated. The results showed that as the rod diameter increased, the rod gap decreased, and the BMFI increased the tailings grade and the tailings yield reduced while the concentrates recovery raised that was regardless of variations in feed size distribution. For the -3.2+0.18mm size fraction preconcentration, the magnetic medium with a rod diameter of 4 mm and a rod gap of 7 mm at BMFI of 454kA/m is used to get a higher performance. For -0.18mm size fraction preconcentration, the magnetic medium with a rod diameter of 4 mm and a rod gap of 4 mm at BMFI of 263kA/m is used to get a higher performance. After the classifying preconcentration, at the optimum condition, the overall concentrate grade increases by 9.56 percentage points and the concentrate recovery is up to the 82.67% with a tailing grade of 10.68% and a tailing yield of 40.31%. The magnetic force, exerted on weekly magnetic minerals was proportional, to the specific susceptibility and square of BMFI. For the same BMFI, the magnetic capturing force on coarse particles increased, and that on fine particles decreased with the increasing of rod diameter. For the lean locked-particles, considering the gravity and viscous resistance of particles, rods with a big diameter were beneficial to the capture of coarse particles and had no influence on the capture of fine particles, while rods with a small diameter were good for the capture of fine particles and not suitable for the capture of coarse particles of lean locked-particles. Keywords: low grade haematite, high-pressure grinding roller, high intensity magnetic separation, pre-concentration

Sep 1, 2012

By Z. Pokrajcic

The traditional comminution circuit is a major consumer of energy ? both as electrical energy and through consumption of media and wear resistant liners. Up to 40% of electrical energy con-sumed at a mine site is attributed to comminution however only a few percent of this energy is used in the generation of new surfaces from size reduction. This paper describes the evaluation of modifications using simulation models based on two operating comminution circuits. The aim of these modifications is to decrease both the amount of electrical energy consumed in the size reduction process, known as direct energy, as well as to decrease the consumption of grinding consumables such as steel grinding media and mill liners, designated as indirect energy. The approach is two-fold: ??Employ, where possible, autogenous grinding techniques to eliminate the need for grinding media and reduce mill liner wear. ??Optimise the use of the grinding energy distribution in the comminution circuit by using more energy efficient grinding devices to target typically problematic features of a comminution circuit such as critical size material from the primary mill and overgrinding in the secondary mill. The investigations show that significant total energy savings, as high as 50% in some cases, can be achieved by employing the techniques described while maintaining circuit throughput and product size. Investigations also show potential benefits in downstream flotation processes as the product size distribution generated from the eco-efficient circuit is generally ?narrower? in shape for improved flotation performance and containing less material in the coarse fraction for overall better liberation.

Jan 1, 2014

By D. Tang

The froth zone in a flotation cell is recognised as a region which contributes to the overall flotation performance. Froth recovery is a measure of the efficiency with which the froth phase delivers particles arriving at the pulp-froth interface to the concentrate. Poor froth recovery in scavenger stages is generally attributed to poor froth stability. The key indicators of froth performance: froth recovery, entrainment and water recovery were measured in an OK3 pilot cell installed at a zinc concentrator in Australia and supplied with scavenger feed. Cell hydrodynamic and pulp chemical conditions during the operation of the cell were also measured as well as bubble growth across the froth phase. The objective of the work was to assess the impact of a number of commercial frothers on the froth performance in the OK3 cell and assess the suitability of using bubble growth as an indicator of froth stability.

Jan 1, 2014

By W. Z. Yin

It is investigated systemically in this paper that the granularity of the precursor, ZnC2O4?2H2O, is influenced by synthetic conditions. Instantaneously adding of precipitation agent is able to control the mean size of precursor ZnC2O4?2H2O under 300nm, which has great function to obtain well-dispersed ZnO nanoparticles in the next step, pyrolysis. The pyrolysis kinetics model of ZnC2O4?2H2O powder is obtained. Two steps take place during the pyrolysis. The first is dehydration, which the pyrolysis kinetic model is 2(1-a)2/3(chemical reaction), A=8.3×108s-1, E=(75.82±3.00) KJ/mol. The second is formation of ZnO, which the pyrolysis kinetic model is (1-a) (random nucleation and latter growth), A=8.45×1028s-1, E=(360.54±12.00)KJ/mol. ZnO nanoparticles obtained by pyrolysis take on self-growth behavior. It is resulted that for precursor ZnC2O4?2H2O pyrolysis time takes obvious influence on the partilces size under 420?, 500? and 600?. Finally, a new flow sheet for synthesis of ZnO nanoparticles is investigated, in which blendes is used as raw material and hydrometallurgy is introduced into it. The whole flow sheet has no industrial wastes, that is all byproducts can be used in the flow sheet recycled, resulted in the de-crease of productive cost and industrial wastes.

Jan 1, 2014

By Jingzhong Kuang, Zheyu Huang, Chuanzhou Guo, Pengfei Liu

"In this paper, scheelite and scheelite coated with Pb2+ (SC) were synthesized by chemical precipitation with the help of ultrasonic. The role of the Pb2+ on scheelite was evaluated. Additionally, the dissolution behavior of minerals and the adsorption mechanism of collectors were investigated systematically via SEM, XRD, EDS. The results indicate that the ultrasonic cavitation can promote the formation of scheelite with large particle size and high crystallinity. Due to the exchange of WO4 2- and OH-, the dissolution of scheelite are not in a 1:1 equivalent amount by chemical formula and the concentration of WO4 2- is higher than that of Ca2+ in the solution because Pb2+ promotes the transfer of WO4 2- from scheelite surface into the solution. The dissolution of scheelite is an endothermic reaction and its enthalpy reaches the maximum value of 692.59J·mol-1 at pH=8~10. But the coating of Pb2+ changes the thermal effect of scheelite in the solution and the dissolution of SC is an exothermic reaction with the dissolution enthalpy of -262.30 J·mol-1. At pH=8~10, the adsorption capacity of sodium oleate and salicylhydroxamic acid on the surface of SC is higher than that of scheelite which delivers that Pb2+ contributes to the scheelite surface dissolution and enhances the adsorption of collectors on the mineral surface, thus achieving activation.INTRODUCTIONIn modern society, tungsten is a type of quite important rare metal and also a strategic resource. Because of its low vapor pressure, high melting point, good electrical and thermal conductivity properties, it is widely applied in high-temperature technology, lighting, machine and engine construction (Zhao,Z.W, 2013; Yan, W, 2017; Ilhan, S, 2013). Both scheelite and wolframite are the major tungsten deposits. With the depletion of easily-processed wolframite, scheelite has drawn a great deal of scientific and industrial attention. Scheelite can be recovered by flotation due to the metathesis of polarity and chargeability on minerals surface via adding regulators and collectors."

Jan 1, 2018

By X. S. Yuan

With a demand for increasing energy efficiency and a need for improving bitumen recovery, a highly integrated solution for sustainable lease development of Aurora North of Syncrude has been proposed and implementation plans are underway. Flocculation and thickening technology as an important component of the integrated solution provides Syncrude an opportunity of rapid heat recovery from tailings and more flexible tailings closure and reclamation options. Flocculation of fine-particle suspensions by polymers is a non-equilibrium process whose performance is strongly influenced by physical and chemical variables. While polymeric flocculants are frequently used to establish the chemical conditions favorable for flocculation, the actual performance of a flocculation process generally depends more on the physical variables, such as the hydrodynamic conditions in mixing the flocculants and slurry. In order to study the effect of hydrodynamic conditions on flocculation of Syncrude fine tailings, a standardized laboratory test procedure called power flocculation has been developed in comparison with the conventional manual mixing methods. It is shown that the agitation speed and time in conditioning the flocculant solution and the slurry have a profound effect on the flocculation performances measured by initial settling rates, supernatant clarity and sediment density. It was found that the optimum bench test conditions for power flocculation of Aurora fine tailings with a sand-to-fine ratio (SFR) of about 1:1 are conditioning of the flocculant solution and the tailings slurry at 250 rev/min to 300 rev/min in 20 s to 40 s. The test results are inter-preted with a flocculant adsorption/redistribution kinetic model that helps understanding of the effect of hydrodynamic conditions on flocculant adsorption, floc formation and floc growth.

Jan 1, 2014

By Volker Vogt, Wolfgang Sand, Eberhard Gock

"It was discovered that the selective activity of bacteria during the extraction of raw material concentrates by means of flotation could also be achieved with extracellular polymeric substances (EPS) excreted by bacteria. EPS, which is extracted by means of centrifuging bacterial cultures, can help to significantly reduce the use of cyanides, approximately 200,000 t/a of which are used for ore dressing today.The bacterium used was Acidithiobacillus ferrooxidans. In order to identify the bandwidth of the oxidation activity, 20 bacterial strains of the strain collection of the University of Hamburg were attracted to iron(II) sulfate and pyrite under defined conditions. All strains oxidized iron(II) sulfate ten times faster than pyrite.EPS has so far been derived from four strains. In general, EPS extracts are divided into a hydrophilic and a hydrophobic fraction. The hydrophilic fraction is composed of e.g. fucose, rhamnose and glucose; fatty acids such as dodecanoic acid, hexadecanoic acid, octadecanoic acid and nonadecanoic acid were found in the hydrophobic fraction.Pure mineral phases and mineral mixtures were used for the flotation tests. As opposed to current knowledge, the results were reproducible with technical flotation machines."

Jan 1, 2003

By Barun Gorain, Aparup Chattopadhyay

"Many double refractory gold deposits are characterized by the dominance of ""invisible gold"" (sub-microscopic gold) as solid solution or as colloidal-sized particles in different sulfides and other phases. These deposits are mainly composed of silicates and carbonates with moderate clay and mica content and with minor amount of sulfides and organic carbonaceous matters. The presence of highly preg-robbing and finely disseminated carbonaceous matter adversely affects gold recovery in leach circuits. Characterization of carbonaceous matters, commonly known as TCM and quantification of gold associated within these carbonaceous matters along with different sulfide and oxide phases is highly complex and challenging. Studies were initiated on various complex ore deposits and also on samples representing various process streams. This paper presents the development of a systematic approach to gold deportment studies using state-of-the-art mineralogy characterization techniques for quantification of invisible and visible metal contents in various species. The relevance of this mineralogy characterization to metallurgy will also be discussed in this paper."

Jan 1, 2014

By H. J. Liang

In this study, zeta potential and contact angle measurements of pyrite before and after interacting with Thiobacillus ferrooxidans are carried out to investigate the changes in its surface properties. The results show that, after pyrite interacting with Thiobacillus ferrooxidans and its metabolite, the surface electricity of pyrite changes obviously, resulting in a notable shifting of isoelectric point to lower pH value, but the contact angle varies little. Bacterial protein plays the most important role in the interaction. This work is helpful to disclose the mechanisms of Thiobacillus ferrooxidans de-pressing pyrite flotability.

Jan 1, 2014

By F. v. d. Meer, G. Kretschmar, T. Mütze, T. Leißner

"Dynamic air classifiers separate particles in a gas flow due to different particle trajectories utilizing differences in the settling velocity of particles as characteristic property for separation. The present contribution takes a close look at the separation of heterogeneous mixtures, in which valuables and gangue minerals show significant differences in density. The focus was on a moist iron ore sample, which was characterized in terms of mineralogy, grain size distribution, and particle size distribution. The material was classified at a cut size of 45 µm and at feed moistures between 0 and 6 wt.-%. Additionally to standard characterization techniques, the moisture of both products was measured as well as the yield of fines as product fraction in a corresponding processing plant. In addition, an automated mineral liberation analysis (MLA) provided information of the enrichment and segregation of individual mineral phases in the products. The MLA of the classification products reveals a selective comminution of the mineral phases and especially on overmilling of the valuables. For the first time, the separation of individual mineral phases has been assessed and compared to the classic assessment of classification processes by means of particle size analyses. KEYWORDS Dynamic classifier, segregation, MLA, selective comminution INTRODUCTION Dynamic air classifiers separate particles in a gas flow due to the different trajectories of the particles. The result of such a separation process depends on the gas throughput of the classifier, the dimensions, design and rotational speed of the deflector wheel, as well as the state of dispersion and thus the geometry of as well as the turbulence and interparticle interactions in the separation zone. Air classification of moist feed materials can be divided into several sub-process (Leschonski, 1977; Mütze et al., 2016): - dosage of the feed material, - dispersing the solid feed material into a gas stream, - feeding the dispersed material into the classification zone by pneumatic conveying, - drying of moist particles during pneumatic conveying, - separation of coarse and fine particles, and - separation of fine particles from gas."

Jan 1, 2018

By Chandra Sekhar Gahan

The present study aimed to investigate the depyritization of coal using iron oxidizing and sulphur oxidizing acidophilic chemolithotrophic microorganisms in an iron free 9K growth medium at varying pulp densities. Three different coal samples used in the shake flask study from three different countries such as domestic anthracite (Korean), Indonesian and Chinese lignite. Experiments were carried out in batch at a controlled temperature of 35 °C and varied pulp densities of 8%, 10% and 12% (w/v) with a working volume of 100 ml containing 10 ml of microbial inoculum and 90 ml of the iron free 9K growth medium. Coal samples were crushed and ground to fine size fractions <100 microns by attrition mill wet grinding. The progress in the experiments were followed by the regular measurements of pH, redox potential, viable planktonic cell count, residual Fe2+ ion concentration, amount of acid addition and amount of slaked lime addition. The pyritic sulfur removal percentage varied between 90-95% with highest sulfur removal with China coal (95%) followed by Korean Coal (93-94%) and slightly lower level for Indonesia coal (90%). However the pyrite oxidation was highest for Korean coal ranging between 78-80% followed by a similar level of pyrite oxidation of 50-61% for the Chinese and Indonesian coal. It was found that 10-12% pulp density would be fairly feasible for all the different coals tested leading to an economical process. Another benefit from this study is the iron free 9K growth medium, which will reduce the operation cost and overall it?s an environment friendly process.

Sep 1, 2012