Search Documents

By Ronald Smeink, Ton de Gouw

"Reagents are an important cost-factor in the flotation of minerals. The mechanism of collectors and frothers has been studied extensively, but on depressants – probably the biggest cost-factor in the reagent suite – very little is actually known. Theories are frequently faced with the bare facts, pointing in another direction. Fundamental research is complicated by the fact that the amount of possible interactions in the flotation cell is almost unlimited and makes “change-one-parameter-at-a-time” experiments questionable and at least difficult to interpret. Also, the adsorption of depressants on the ore is very strong and desorption merely impossible. Detection methods therefore tend to be indirect and – therefore - non-specific about the location of the depressant on the ore.Depressants are supposed to adsorb selectively on gangue minerals; not on the valuable minerals in the froth. In order to be able to develop better and ‘’smarter’’ depressants, an analytical method is therefore required that will enable to detect which (=qualitatively) depressant, in which concentration (=quantitatively) sits where exactly (= selectively) on the mineral surface. (Answering the question: ‘’ Which minerals is located direct under the depressant?’’)And also: does the depressant compete with other reagents for that location? (like collectors) This analytical method is under development. The actual status of the method is promising and the results will be shown."

Jan 1, 2003

By Genrich A. Denisov

Principles of ecologically friendly geo-technologies construction are formulated on the basis of the works of the leading scientists in the field of rational processing of mineral resources of the Russian Academy of Sciences. One of these concepts is a new direction in rotational disintegration of mineral and technogenic raw material with the purpose of effective subsequent enrichment. A large amount of practical experience has been accumulated in the industry on selective destruction by application of vibrational method on initial material with consideration of its physical-mechanical properties and mineral structure. This method is successfully realised in a conic inertial pulverisation devices constructed by Mekhanobr Institute (St.-Petersburg). A new construction of conical-inertial pulverisation with a modification of disintegration force has been developed recently at Mekhanobr Institute. It allows, in some cases, to increase selectivity of subdivision and to avoid over-disintegration. Advantages of “wet” subdivision methods in conic inertial disintegration devices are proved. The efficiency of such subdivision can be increased due to rational use of the phenomenon of a dislocation-dynamic diffusion. Its advantage is proved by the effect on disintegrated material by frequency-modulated variable electrical fields of low power. It was shown in industrial conditions, that the productivity of the spherical mill can be increased by 10 %, and that it also prevents ecologically harmful surface active substances (SAS) in milling zone and it reduces the dust content in the air. The techniques of tentative estimation of efficiency of various proceedings technogenic materials and their classification are created. The scientific fundaments of rational, ecologically friendly technology of processing and regeneration of various kinds of technogenic raw material are developed. A number of effective technologies on processing of wastes is developed and inculcated in concentration factories and metallurgical factories.

Jan 1, 2003

By M. Brozek, W. Pawlos

"The separation of raw materials in the separator with ferromagnetic liquid occurs due to differences in magnetic and gravitational properties of respective components in relation to each other and to the liquid. In the separator with wedge-shaped pole shoes and the working space axis inclined at a certain angle to the horizontal direction, the paths of grain movement at fixed separation conditions depend on its physical properties. Due to this, the levels of grains outlet from the separator working space are differentiated according to differences in their physical properties. The distance between the levels of outlets from the separator working chamber depends on magnetization of the liquid which is proportional to the liquid density, on the magnetic field intensity and the inclination angle of the separator working passage to the horizontal axis. The separation accuracy is higher the larger is the distance between the outlet levels.The paper will present the methods of visual observation and recording of movement paths of coal grains of different physical properties in the paramagnetic liquid which was the water solution of manganese chloride. The paths were recorded with a video camera in the working chamber by means of a specially constructed device, acting as a periscope, which were then transformed into digital images. Experimental movement paths were confronted to the paths obtained in a theoretical way by means of solving differential equations of movement by a numerical method, achieving good compatibility of experimental and theoretical results. The equations of movement were solved with taking into consideration the drag force, expressed by formula for laminar and dynamic conditions of motion.The course of the path of grain movement depends on grain and liquid physical properties, magnetic field intensity and inclination angle of the working space to the horizontal direction. The two latter parameters can continuously control the process of separation."

Jan 1, 2003

By Vladimir I. Ryaboy, Konstantin M. Asonchik

"At flotation of sulfide-barite ores of one of deposits sulfide and barite concentrates are obtained. In sulfide cycle potassium xantogenate as a collector in consumption of 200 g/ton, methylisobutylcarbinol (MIBC) as a foaming agent in consumption of 30 g/ton and also liquid glass are used. In barite cycle tall oil as fatty acid collector in consumption up to 400 g/ton is used.Sulfide concentrate represents mainly gold- and silver-containing pyrite. The contents of gold makes not less than 10 g per ton, silver - not less than 278 g/t. Barite concentrate contains up to 86% of barite.Factory is working in water recirculation conditions. Owing to that in barite cycle fatty acid collector is used, technological water from tailing repository contains fatty acids soap up to 25 mg/l. Before submission into sulfide cycle this water is conditioned with active carbon to delete the main part of fatty acid collector. The active carbon consumption makes 0,4-0,5 kg per 1m3 of water or 1,5-2 kg per ton of ore. The above mentioned consumption of active carbon improves reducing of contents of fatty acid collector from the initial concentration of 25-30 mg/l to 4 mg/l. At concentration 4 mg/l fatty acid collector does not render negative influence on flotation index in sulfide cycle. At the absence of active carbon pollution of sulfide concentrate and its irrevocable lost are observed."

Jan 1, 2003

By Atsushi Shibayama, Toyohisa Fujita, Wan-Tai Yen, Ke-jun Liu

"A gold has been leached with ammonium thiosulfate solution and several leaching conditions have been studied. The leached solution has been recovered by solvent extraction and the optimum conditions have been investigated.SUMMARYIn this investigation, a sponge gold sample (99.92% pure) has been leached with ammonium thiosulfate solution. The effects of CuSO4, (NH4)2S2O3, (NH4)2SO4, NH4OH and retention time on the gold leaching % (extraction %) and thiosulfate oxidation % (consumption %) have been studied. The copper ion acts as a catalyst in gold dissolution. On the other hand, it also accelerates oxidation of thiosulfate (consumption). It was found in this study that the best gold extraction condition was obtained at 43.2 ks with 0.8 – 1.0x103 mol/m3 (NH4)2S2O3, 30 mol/m3 CuSO4, 2.0 – 3.0x103 mol/m3 NH4OH, 0.4 – 0.5x103 mol/m3 (NH4)2SO4, pH 10±0.2 and 150 rpm. The thiosulfate oxidation was about 15% of the initial concentration."

Jan 1, 2003

By Stephen Gay, Dewetia Latti

"When improving a plant a mineral processing engineer would like to know the mineral composition distribution. In order to assess this distribution in particles, as compared to the corresponding distribution in particle sections, a procedure needs to be applied to the observed particle sections. Such a procedure is called a stereological correction. There exists many stereological correction procedures, but one group of such procedures is based on using those stereological equations that do not require making assumptions regarding particle shape or texture. These equations are called geometric probability equations.Davy derived a geometric probability equation to estimate the covariance of mineral composition distributions for particles from both particle sections and linear intercepts. This covariance can be used to measure the variance of the particle composition distribution of each mineral. The equation as presented by Davy requires textural information; however the equation was modified by Gay to be more directly applied to particle sections and linear intercepts. The variance obtained from applying this equation is fundamental to the binary stereological correction procedures developed by Gay and his colleagues; the covariance is fundamental to the multiphase stereological correction.Thus far, validation of both the binary and multiphase stereological correction has been achieved using numerical simulation. This paper shall present results comparing the covariance (and variance) estimates from Gay’s equation with actual three-dimensional information obtained from serially sectioning particles. This involved mounting a set of particles and continuously sectioning all particles uniformly so that the three dimensional structure of the particles could be obtained.The mineralogical data to which the equations described above were applied were derived from two individual size fractions from a hard-rock titanium deposit. The deposit contains a range of minerals and of mineral textures and the two size fractions selected were:"

Jan 1, 2003

By A. F. Raschenko, Y. A. Golodcov, V. V. Elshin

"The autoclave noble metal desorption in apparatuses with a dense stationary sorbent layer is perspective for the technology of sorption gold and silver extraction from solutions and pulps by carbon sorbents. The study of the mechanism and optimization of the autoclave desorption process involve some difficulties. To overcome them it is necessary to use mathematical and quantum-chemical modelling. The given paper deals with a mathematical model for the dynamics of gold and silver desorption from active carbons by alkali solutions based on the physical-chemical notions of the process. The kinetics and the mechanism of the process were investigated using the mathematical model for gold and silver desorption.The calculation of the efficient mass-transfer coefficient (ße) for various initial and intermediate noble metal concentrations in carbon (Cy) made it possible to find that the dependence of ße on Cy in case of gold desoprtion shows a clear extreme character. The value of the initial metal concentration in carbon therewith does not influence the character of the curve the inflection point of which is changed essentially at elevated process temperatures only. The revealed characteristic property, in the author's opinion can only be indicative of the change in the mechanism of gold desorption under autoclave desorption conditions. The assumed [Au(CN)(OH)]- type intermediate that has a higher diffusion coefficient in comparison with the adsorbed complex [Au(CN)2]- can be considered as an intermediate compound in the process of gold desorption."

Jan 1, 2003

By Elzbieta Mielczarski, Jerzy Mielczarski, Jan Drzymala, Yann Duval

"The monoalkyl ethers of polyethylene glycols are universal flotation reagents because they can be used as collectors, frothers, surfactants, and depressants. Their collecting power was demonstrated for different minerals including coal and quartz.It was confirmed in this work that monoalkyl ethers of polyethylene glycols could be used as collector in flotation of quartz in a monobubble Hallimond cell. Since feldspar does not float in the same cell, it was also shown that selective separation of quartz and feldspar in the Hallimond tube is possible. However, a trail to use the monoalkyl ethers of polyethylene glycols compounds for separation of quartz and feldspar by flotation of mixture of these minerals in a Mechanobr laboratory flotation machine was futile, indicating that these reagents required special environment for flotation.Most probable parameter responsible for a decrease in quartz flotation in the flotation machine is the hydrodynamics of process, and different adsorption/desorption conditions. To prove this, another series of experiments was carried out to separate quartz and feldspar, in which a laboratory flotation column was utilized. The performance of the flotation column was in between that of in the Hallimond tube and flotation machine. These experiments confirmed that the hydrodynamics of flotation plays a vital role in flotation of quartz with monoalkyl ethers of polyethylene glycol compounds."

Jan 1, 2003

By D. Whittles, S. Kingman, K. Jackson, S. Bradshaw, N. Miles

The influence of microwave energy at high electric field strength on ore strength has been investigated. Two ores of varying mineralogy were treated in both multimode and single mode microwave cavities. After treatment, any change in strength relative to untreated ore was established. It was shown that in the multimode cavity reduction in strength was related to the applied power level. Results of tests carried out in the single mode cavities showed that, for both ores, reductions in ore strength > 50% could be achieved in very short periods (<1 second). Thermal stress analysis showed that the mechanism of microwave induced failure was the development of tangential stresses at the grain boundaries. It was concluded that operation at 915 MHz with high power and short residence times gives feasible scale-up possibilities.

Jan 1, 2003

By Francesco Montanari, Gianni Schena

"Recent improvements in X-ray computed tomography allow investigation of objects several tens of millimetres in dimension with spatial resolutions in the order of a few microns. These improvements are made possible by coupling the micro-focus technology adopted by some of the latest cone-beam X-ray sources with an increase in the efficiency of the detectors. The micro-focus technology allows the production of clearer images at high magnification by reducing the penumbra (fuzziness) associated with larger focal spot size.Even higher resolutions can be expected in the next few years with the commercialisation of nano-focus X-ray tubes. In practice one can inspect a system of fine composite particles and analyze the different mineralogical phases in each individual particle. Computed tomography allows accurate liberation studies, e.g. providing liberation spectra or washability data in tens of minutes. However, on-line application of micro-focus computed tomography is unlikely in the foreseeable future, despite rapid development.Dual-energy (DE) radiography is another X-ray technique, which allows retrieval of the volumetric content of valuable components in two-phase particles in a fraction of a second. A digital radiograph of a single two-phase particle produces a grey level image, where the luminosity of the pixels is determined by the sum of the attenuation levels of all the structures. Thus morphological and compositional effects concur to produce the radiographic image, which does not allow retrieval of the composition of the particle, as the 3D-structure of the particle is compressed into a 2D-image, with an obvious loss of information. Thus, in principle it is not possible to discriminate between thick, comparatively penetrable, and thin, comparatively impenetrable mineralogical components."

Jan 1, 2003

By Kang N. Zhong, Hui H. Luo, Yunan Phosphate Chemical Co., Yi H. Wei, Yao J. Li, Yu L. Wang

"The three kinds of phosphate ores (igneous, metasedimentary and sedimentary) found in China have great differences in flotation flowsheets and reagents suite because of their crystal structure and mineral composition. The igneous and metasedimentary apatites have good floatability with fatty acid as collector and waterglass, sodium hydroxide or sodium carbonate as conditioners. The sedimentary phosphate is very difficult to beneficiate by direct flotation because of their poor floatabilities and relatively high content of MgO and SiO2, even though the dolomite depressants are used sometimes.The differences in floatability of apatites in China are closely related to their differences in specific surface area. The amount of collector to float apatite increases with the specific surface area. Apatite with lower specific surface area showed good floatability at lower collector concentration. Apatite with a higher specific surface area needed a higher concentration of collector. The content of CO3 2- will affect the specific surface area of apatite by distortion of its crystal structure and consequently affect its floatability.Dolomite can be easily rejected from apatite in a weak acidic medium (pH=5), especially in phosphoric acid medium by reverse flotation. Quartz and siliceous gangue in sedimentary apatite can be removed by direct flotation using fatty acid or by reverse flotation using amine. Amine is not practically applied because sedimentary apatite in China is usually very fine and needs fine grinding, which always results in excessive, very fine, stable and non-flowable foam.Based on the floatability of phosphate ore in China, a two-stage flotation process, direct and reverse flotation (D+R), was developed to beneficiate sedimentary ore. For the Haikou phosphate ore containing 25.11% P2O5, 3.46% MgO and 16.5% SiO2, a concentrate containing 31.84% P2O5, 0.48% MgO and 14.8% SiO2 can be obtained through a continuous D+R test at a recovery of 89%."

Jan 1, 2003

By Jochen Petersen, David G. Dixon

"Although heap leaching may be perceived as a somewhat low-tech route for the extraction of low-grade minerals, the underlying physical, chemical and biological processes are in fact extremely complex. There has been increased interest in heap leaching of sulphide minerals in recent years with the advent of controlled bio-heap leaching, and the need to mine more marginal ore deposits.A detailed investigation into the dynamics of heap leach processes has provided much insight into the underlying complexities, and has led to the development of a sophisticated modelling tool, HeapSim. Some of the sub-processes that are modelled include mineral kinetics, particle size effects, bacterial growth, oxidation and adsorption, gas adsorption, pore diffusion, bulk advection, gas balance and heat conservation. The interplay of these various sub-processes is illustrated in the paper.Two case studies are presented which illustrate specific features of the model for different applications and how these have helped to identify key areas of concern. The first is focussed on chalcocite heap bioleaching, which shows that by nature of the reaction the process is strongly dependent on the initial supply of acid to the mineral site. In heaps this acid supply can be severely limited by the rate of diffusion from channels of flowing solution into stagnant zones of the heap, whereas in narrow-bore laboratory columns this effect is not observed."

Jan 1, 2003

By N. Raeis Hosseiny, S. H. Bassir

"Chador-Malu iron ore is one of the most important iron mines of Iran.About 98 percent of Fe in the ore is in shape of Magnetite, Hematite, Martite, aqua oxide of Iron and the other irons are with ferrous silicates, actinolite, cholorite and ferrous dolomites. 1% of Fe has replaced in pyrite. The phosphor distribution in the ore is non-hemogenous and its average in the whole of the deposit is 94%. It is in shape of Apatite.This mine contains considerable phosphor, which makes it useless for metallurgical uses. At this mine the phosphor is reduced in the iron ore at two steps. At the first step, magnetic part of the ore is separated from the gangues and phosphors by magnetic separator. At the second step, the ore is enriched by the flotation methods. Experimental flotation methods to obtain the optimum conditions are as follows:• Effect of Starch as Hematite depressant with ATRAC as Apatite collector• Effect of Sodium silicate as Hematite depressant with ATRAC as Apatite collector• Effect of ASAM as Apatite collector with Sodium silicate as Hematite depressant• Effect of ATRAC (BEROL) as Apatite collector with Sodium silicate as Hematite depressant• Effect of ASAM & ATRAC mixture as Apatite collector with Sodium silicate as Hematite depressant• Effect of Kcarbonate as pH-modifier• Final test to Optimize pH, Collector, DepressantAt this research we have found the optimum circumstance of the flotation of Chador-Malu iron ore in order to decreasing phosphors of iron oxide and floating of Apatite to make pure Hematite.To reach the optimum conditions, some tests were done with different amounts of pH, collector and depressant. The results are as follows:"

Jan 1, 2003

"The Merensky Reef is a platinum group minerals (PGM) bearing reef in the Bushveld Igneous Complex in South Africa. The reef has been treated by bulk PGM and sulphide flotation with the aim of maximisingthe valuable minerals recovery and gangue minerals rejection.Synthetic water with a calcium concentration of 80 ppm and 500 ppm was prepared and the flotation results obtained were compared to a simple electrolyte in order to determine the effect water quality has on pentlandite and pyroxene surface alteration and, ultimately, floatability. During the study, the possible effect of interactions between the minerals investigated and Ca2+ ions in the presence of sodium isobutyl xanthate was studied at pH 6 and pH 9 by means of zeta potential determinations, microflotation tests and ToF-SIMS analysis.The results obtained on 1:1 pentlandite-pyroxene mixtures showed that the quality of process water plays an important role in flotation. The flotation recoveries of pentlandite and pyroxene were lower in synthetic process water compared to those obtained in a simple electrolyte solution."

Jan 1, 2003

By S. J. Neethling

"Flotation is a complex process with many factors that influence the performance of a cell. This paper examines the impact of several key variables on the performance of flotation cells. The study makes use of a simulator for the froth phase of the flotation vessel, as the main purpose of this study is to separate the impact of different variables from one another.In experiments it is very difficult to separate the effect of variables from one another as a change in a singe input parameter, such as air rate, invariably also affects many of the other key variables, such as bubble size and bubble bursting rates. This interaction between variables makes it very hard to experimentally separate the impact of, for instance, the air rate from that of bubble size or bursting rate. In the simulator, though, it easy to make independent changes to these variables.In order to achieve this a base case simulation that is typical of many of the rougher cells found in sulphide flotation circuits was carried out. Four key variables, air rate, incoming bubble size, surface bubble size and the fraction of the bubbles flowing out of the cell unburst, were varied in order to obtain the system’s response.The most significant results were obtained when the bubble size was varied. An increase in the incoming bubble size has the effect of reducing the pulp zone recovery, but increases the froth zone recovery. If it were possible to vary the incoming bubble size without influencing the overflowing bubble size, the impact of the change would be unclear because of these two competing effects. The effect of a change in the overflowing bubble size has an opposite effect on the froth recovery, with larger bubbles resulting in lower froth recoveries."

Jan 1, 2003

By Christopher Davey, Marian Mazurkiewicz, Yvonne Spooner, Dana Hankey, Peter Kanjorski

The concept of a high pressure liquid jet mill with highly unsteady flow, has been developed and recently patented by Cornerstone Technologies LLC (CsT), for the purpose of micron and sub-micron particle production. The mill accepts feed sizes up to 15mm for some materials and is capable of submicron production. Successful material range from precious metals such as silver and palladium to dielectric components and substrates such as Barium Titanate slips, zirconia, titania and silica. The process has also succeeded in adequately reducing the size of materials for both composite and coating uses such as anthracite coal, graphite, chrome metal, wollastonite and more than 100 others. A unique design approach has been taken to highly maximize the energy flux in the mill's chambers to create extremely high turbulence and destructive cavitation. This is assisted by shock waves, which cause particles to undergo ultra high frequency pressure pulsations, high frequency collisions and then abrasion, shattering, hydrowedging, and cleaving. Due to these extreme properties the processing occurs in just fractions of a second allowing throughputs up to 1000 kg/h on a machine that would fit inside a 60 cm box. The technical solution and technological advance, as well as the environmental and economic benefits indicate rapid and wide spread acceptance of high-pressure liquid jet milling in modern industry.

Jan 1, 2003

By Chen Shuwen, Yao Zhihua

In the process of thickening dewatering_the motion state of two- phase flow in a thickener has a very great influence on thickening efficiency. The investigation was made using copper mill tailings. In this investigation the authors explored the formation conditions and motion range of density current in the thickening process by model experiments, and analyzed the influence of density current on thickening efficiency. The results have shown that the formation of density current has relations with the structure parameters of a thickener and thickening process. The density current and its forming location affect thickener’s working efficiency. The author measured the motion state of two- phase flow in a 53-m dial. thickener for copper mill tailings under its operation conditions and analyzed the density distribution and motion state of two-phase flow in the thickener. The results obtained by the industry tests have shown that the motion state of two- phase flow in the thickener can be greatly improved by modification of its structure, achieving a great improvement in its thickening efficiency. It is concluded that, a thickener’s working efficiency depends on the formation and motion range of density current in it, which is of great importance to designing and establishment of thickener’s working parameters.

Jan 1, 2003

By S. Fiore, M. C. Zanetti, C. Clerici

The processes and fluxes of a cast iron foundry plant located in the North of Italy were analyzed in order to determine the amount and kind of wastes produced from the different activities. The main fractions are the molding sands, furnace muds and powders coming from the dust abatement plant, the exhaust lime, the furnace refractory, the metallic shotting and the sludges and powders coming from the dust abatement plant of molding lines for a total production equal to 800 t/d. All wastes were sampled and particle-size and chemically characterized to evaluate the best recycling or reuse solutions. Wastes were sieved and divided in three categories according to the particle-size dimensions: below 0.1 mm, between 0.1 and 0.6 mm and above 0.6 mm. The fraction above 0.6 mm dimension underwent magnetic separation to recover and quantify the potentially available iron fraction. The fraction between 0.1 mm and 0.6 mm was chemically characterized in order to understand if it could be fed to the sand regeneration plant. The below 0.1 mm fraction was characterized to evaluate the following recycling and reuse solutions: additive for molding sands and/or raw material for the concrete industry.

Jan 1, 2003

By P. Huang, D. W. Fuerstenau

Various factors that control the natural flotability of talc, including differences due to crystal face and edge effects, were delineated. For study of talc depression phenomena, dextrin was used as a model depressant. For the enhancement of talc flotation, dodecylammonium acetate (DDAA) was used as the collector. The interaction of DDAA with talc was assessed by flotation experiments and electrokinetic (zeta potential) measurements, from which the role of hydrophobic bonding can be demonstrated. The results presented in this paper provide useful information on how the crystal chemistry and surface chemistry control the electrical double layer, adsorption phenomena, wettability, and flotation behavior of talc in aqueous media.

Jan 1, 2003

The introduction and subsequent ascendancy of autogenous and semi-autogenous milling for comminution circuits has undoubtedly lead to many economic advantages. From a process viewpoint, however, at least one downside has been the sensitivity of these machines to process input variations. Foremost among these is ore competence, though feed size comes a close second. This sensitivity is due to the reliance of ag/sag mills on the feed ore for their grinding media competence and size. Autogenous (ag) mills are the most sensitive in this respect with semi-autogenous (sag) mills being increasingly less so as the ball charge is increased. Increasingly designers and operators are recognising the importance of feed size and the benefits of manipulating it to improve performance. This has been achieved by installing additional crushing/screening capacity ahead of the ag/sag, better operation of the primary crusher, better control of segregation cased by stockpiles and bins and by changing blast design/practices to modify the ROM size distribution. This paper describes the influence of feed size distribution on ag/sag mill performance with reference to a range of plant data. It particularly concentrates on how changing blasting practice to modify ag/sag feed size can have a considerable overall benefit.

Jan 1, 2003