Search Documents

By Rob D. Morrision, Paul W. Cleary

"The best accepted method for design of autogenous and semi-autogenous mills is to carry out pilot scale test work using a 1.8 m diameter by 0.6 m long pilot scale test mill. The load in such a mill typically contains 250,000-450,000 particles larger than 6 mm, allowing correct representation of more than 90% of the charge. This scale of DEM model is now within the practical range of standard workstations running an efficient DEM code.This paper describes various ways of extracting collision data from the DEM model and translating it into breakage and wear estimates. Account is taken of the different breakage mechanisms (impact and abrasion) and of the specific impact histories of the particles in order to assess the breakage rates for various size fractions in the mills. These impact histories have the potential to be directly related to breakage as they most resemble the single particle breakage tests which are used by the JKMRC to calibrate more traditional population balance models for variations in ore behaviour. However, the specific impact histories also show a background of many low energy collision events within the mill. This Background may constitute what is usually regarded as “abrasion” breakage. As might be expected, high impact events are concentrated in the toe of the charge and near to the mill shell where the forces associated with the load bearing on each particle is more concentrated."

Jan 1, 2003

By M. Salas, L. Rolf, H. Z. Kuyumcu

"Industrial use of abrasive stress takes place in the area of fine grinding and in order to clean surface contaminated soil particles. Also, at many mechanical operations abrasion emerge as an unintended side effect. At the Institute for Raw and Waste Material Processing at the Technical University of Berlin systematic investigations are carried out, to further the knowledge regarding the dependence of abrasion process on material properties and stress mechanisms as a basis for design and optimisation of the process or for its avoidance. Aim was the mathematical description of the abrasion process running with a single particle stress. For the purpose of investigations an agitation cell was used. Limestone served as material.In the presented work the influence of particle diameter, particle shape and collision energy on the mass and particle size distribution of abrasion debris was studied. The surface geometry of the particle was characterised by the particle shape factor ?x and the particle diameter dp. The particle shape factor ?x stays in direct relation with the abrasion degree x, and can be substituted by a mathematical function of x.Physically the particle shape factor ?x can be interpreted as a proportion of abrasive stresses splitting up complete crystals and crystal fragments. These two different mechanisms depend on different ratios of curvature of the surface of the stressed particle. The abrasive stress of strongly curved surface areas leads to separation of complete crystals. The abrasive stress of weakly curved surface areas leads to separation of crystals fragments. Accordingly the mass of wear mAb and median diameter of the abrasion debris d50 are different. The derived mathematical relations consider this behaviour by the particle shape factor ?x , which represents the ratio of the mixture of both stress mechanisms. The dependence of the particle shape factor ?x on the abrasion degree x with an exponent approximately to 2/3 points out that the particle shape factor ?x represents a surface area relation."

Jan 1, 2003

By John Ralston, Stephen Grano, Yongjun Peng, Daniel Fornasiero

"A specially designed mill which allowed the control of pH throughout grinding was used to study the effect of rgrinding conditions on galena flotation and galena separation from pyrite. The various reactions occurring on the mineral surface were investigated by a range of techniques, including OH- addition to maintain the grinding pH, EDTA extraction, XPS and ToF-SIMS measurements.Galena flotation and galena separation from pyrite were strongly dependent on the metal oxidation species produced on galena and pyrite surfaces under different grinding conditions. Iron oxidation species depressed both galena and pyrite flotation, whilst lead oxidation species activated pyrite but had little effect on galena. Optimum galena flotation and galena selectivity against pyrite were achieved by selecting grinding conditions that enabled lead and iron oxidation production to be controlled."

Jan 1, 2003

By Volker Vogt, Wolfgang Sand, Eberhard Gock

"For about 20 years, the use of bacteria to control the flotation process for the production of raw material concentrates has been the subject of worldwide scientific and engineering efforts. The objective is to reduce the consumption of biologically non-degradable toxic reagents. The principle idea is to use the activity of bacteria in natural leaching processes – known since the middle of the last century – for controlling flotation processes.It was discovered that the selective activity of bacteria during the extraction of raw material concentrates by means of flotation could also be achieved with extracellular polymeric substances (EPS), excreted by bacteria. EPS, which is extracted by means of centrifuging bacterial cultures, can help to significantly reduce the use of cyanides, approximately 200,000 t/a are used for ore dressing today.The bacterium used was Acidithiobacillus ferrooxidans. In order to identify the bandwidth of the oxidation activity, 21 bacterial strains of the strain collection of the University of Hamburg were attracted to iron(II) sulfate and pyrite under defined conditions. All strains oxidized iron(II) sulfate ten times faster than pyrite.EPS has so far been derived from four strains. In general, EPS extracts are divided into a hydrophilic and a hydrophobic fraction. The hydrophilic fraction is composed of e.g. fucose, rhamnose and glucose; fatty acids such as dodecanoic acid, hexadecanoic acid, octadecanoic acid and nonadecanoic acid were found in the hydrophobic fraction. Pure mineral phases and mineral mixtures were used for the flotation tests. The outcome was reproducible results with technical flotation machines. The research results known so far are mainly based on investigations with micro flotation devices, which are usually used for the characterization of reagents and which do not allow a direct translation to the technical scale."

Jan 1, 2003

By E. Barsky

"The aim of separation is to obtain two products that are as distinct as possible from each other. It is currently believed that the most objective criteria for the quality of a separation are the Hancock criterion and the entropy criterion.1. Hancock criterion:- for yield of fine product"

Jan 1, 2003

By Rhulani F. Maluleke, Francis W. Petersen, John H. Marsh, Johann de T. Steyl, Allan Nesbitt

"Pressure leaching of chalcopyrite and nickeliferrous pyrrotite at temperatures between 105 and 200 ºC has been proposed as a potentially viable route for the extraction of mineral elements from sulphide concentrates. In general, these concentrates contain iron, and the economic success of the processes is partially dependent on the choice of the environmentally acceptable iron-removal technique. One of the most widely used methods for the removal of iron from sulphate liquors is precipitation as hematite, goethite, or jarosite. The nature of the iron precipitate formed, dictates downstream dewatering and residue treatment and disposal options. However, a better understanding of iron precipitation under the defined process conditions would consequently be of benefit in process design and optimization.This study investigated the precipitation of iron in the autoclave at temperatures between 105 and 200 ºC. The effects of temperature, acid concentration, iron concentration, and the presence of other metal cations on the nature and composition of the precipitates were determined."

Jan 1, 2003

By Rogerio C. Guimarães, Antonio E. C. Peres

The production of phosphate concentrates (phosphate rock) from slimes represents a challenge to the phosphate industry worldwide. In Brazil, this challenge is particularly relevant due to the consistently low P2O5 grades and the igneous origin. The Brazilian phosphate deposits are made up mainly of apatite from alkaline chimneys, representing 80% of the Brazilian reserves; phosphorite deposits contribute 18% and the other sources (guano, phosphorous bauxite, and apatite from veins) reach 2%. The Brazilian industry beneficiates phosphate ores that are mineralogically more complex than those treated elsewhere. The low apatite grade, inherent to the igneous Brazilian ores, added to the mineralogical complexity due to the weathering of the rocks, has represented a permanent challenge to the Brazilian process engineers. The total measured, indicated and inferred reserves reach 3.2 million tonnes of ore with average grade 11% P2O5. The development of local technology for phosphate beneficiation started in the 1960’s. The first industrial experiences of producing phosphate rock from slimes (-44µm or -325#) fraction started at Arafertil, currently Bunge Fertilizantes SA, in Araxá, in the 1980’s. This production corresponds, nowadays, to 35% of the total production of concentrates in the company (830,000t/year) in a circuit consisting of desliming in 40mm microcyclones and concentration in flotation columns, corn starch and fatty acids being utilised as reagents. The performance of slimes flotation and the process control, at Bunge´s concentrator, were improved after the introduction of column flotation technology, in the first half of the nineties. The column flotation technology for slimes recovery was expanded to other Brazilian concentrators still in the nineties: Ultrafértil (Catalão – GO), Bunge (Cajati – SP), Fosfértil (Tapira – MG) and Copebrás (Catalão – GO). At present the Brazilian production of phosphate rock is approximately 4.5Mt/year, with a strong trend for a market increase. Genuinely Brazilian technology is utilised for the processing of slimes, the concentrates representing 11 to 13% of the overall production. The production of apatite concentrates from slimes was relevant to increase phosphate recovery and reduce costs, contributing to the growth of the fertilisers industry.

Jan 1, 2003

By J. Faitli, I. Tarján

One of the basic processes of process engineering is the production of dense suspensions. The major two equipment of this task are the periodically operating propeller mixer, and the continuously operating mixer tank based on the flow principle. In the laboratory of the Department of Process Engineering at the University of Miskolc, laboratory scale experimental setups had been built of both types of mixers in the frame of the FKFP 0504/1999 signed research project, supported by the Hungarian Ministry of Education. By these experimental setups many systematical experimental series had been carried out by test materials of water as the dispersing media and sand, power plant fly ash and magnetite as the granular solids. On the basis of the literature and these experimental investigations, scale-up methods had been developed for both types of mixers for the determination of the main technical parameters of industrial size equipment.

Jan 1, 2003

By H. U. R. Kattentidt, W. L. Dalmijn, T. P. R. de Jong

"Research at Delft University aims to develop systems for automatic inspection and sorting of bulk solids which can be applied in the mineral processing and recycling industry. A recent development includes an automatic sorter based on airport X-ray inspection technology. It is designed for continuous inspection and sorting of 5 – 150 mm solids and has as objective a cost effective and high capacity on-line inspection and sorting.Dual energy X-ray transmission imaging provides instantaneous data about particle dimensions and the atomic number distribution. The system provides particle thickness and average atomic number on a pixel level at scanning speeds between 250 and 500 lines / second. With existing X-ray components inspection speeds between 0.5 and 2 m/s at approximately 1-meter inspection width and between 1.5*1.5 and 5*5 mm2 sensor resolution can be achieved.Imaging algorithms that were developed by Delft University for applications in recycling, waste cleaning and other applications acquire shape, size distribution and composition data. Currently on-line processing of a product at a rate of around 200 particles per second is possible using a standard PC. Experiments with a demonstration X-ray unit indicated good potential for various applications in solids processing. They include continuous inspection of organic content, sulphur, chlorine, ash, and metal distribution. It is applicable for coal cleaning, ore sorting, industrial minerals, and various applications within waste cleaning and recycling. Dual energy X-ray transmission fundamentals and recent progress in system development and applications are presented."

Jan 1, 2003

By G. Onal, E. Gock, H. Dincer

"During the conventional chromite dissolution process; chromite ore concentrates were ground to at least <90 µm using the ball mill and after adding Na2CO3 and leaning material (instead of CaCO3 also residues from the leaching process) at a ratio of e.g. 1:0.75:1.2, depending on the specific formulation, follows the digestion e.g. in a rotary kiln, heated in countercurrent. The reaction time is 3 to 8 h. The calcine is comminuted and leached with water or a thin chromate solution. Depending on the type of ore used, the yield is 75-85 %. The disadvantage of the above-described process is that it is impossible, using current technology, to achieve a complete digestion of the chromite ores and that the chromium-containing residues have to be disposed of as special waste, involving a large financial effort.The subject of this study was the investigation of the effect of vibratory milling on chromite dissolution. The impact stress in the vibratory mill causes the mechanical activation of chromite, which is characterised by lattice defects. The degree of mechanical activation can be quantified by measuring the relative X-ray diffraction intensities at the parent lattice planes of chromite. Each relative X-ray diffraction ratio correlates with a certain degree of digestion. As opposed to vibratory milling, a complete digestion of chromite using a ball mill is impossible, even at extremely long grinding times.In this investigation a chromite concentrate from Pulpinar/Kayseri with content of 44 % Cr2O3 and the Eccentric Vibratory Mill was used. In order to verify the effect of the vibrating grinding on chromite dissolution, reaction kinetic investigations on digestion and leaching were carried out."

Jan 1, 2003

By Mikhail I. Khersonskaya, Mark I. Mantsevich, Andrey V. Tarasov

"Due to depletion of the existing ore deposits the content of non-ferrous metals in produced ores has an inevitable tendency to decrease. Processing of low-grade ores is associated with production of low-grade selective concentrates and poses serious problems for the non-ferrous industry relating to increasing losses and expenses for waste treatment and disposal.The main component contaminating selective concentrates is iron sulphides.Copper-nickel, copper-zinc and polymetallic ores have been discussed as most important types of ores requiring removal of iron sulphides.One of the promising directions for development of selective flotation technology is the use of lowmolecular organic depressors. An advantage of organic compounds is in the possibility of multi-variant structure of organic molecules, which permits selection of a most efficient reagent for the given conditions. Another way for improving the grades of concentrates is concentration of valuable constituents associated with iron sulphides in an intermediate product and upgrading of the latter by chemical and metallurgical techniques.In order to remove iron from nickel concentrates, specific process conditions have been developed for selective flotation of pentlandite with the use of an organic depressor for pyrrhotite. The use of a depressor for flotation of high-grade copper-nickel ores ensures an increase in the nickel content up to 14% in the nickel concentrate produced as compared with 7% when using conventional process conditions, along with a nickel recovery improved by 2-3%."

Jan 1, 2003

By Knut L. Sandvik, Erik Larsen

"Estimated global solar energy demand in 2001 required approximately 5,500 tons of silicon feedstock. This required 65,000 tons of quartz. If the trend continues, the solar energy demand in 2010 would require approximately 30,000 tons of silicon feedstock and 350,000 tons of quartz, although the need for quartz probably will be lower than this due to higher solar cell efficiencies, larger and thinner wafers, more extensive recycling of waste material and new routes for the production of silicon feedstock. The raw material requirements for the production of metallurgical-grade silicon are most likely to change. This may favour increased beneficiation of primary raw materials in the future solar cell production chain.SOLAR CELL PRODUCTION CHAIN SCENARIOSThe major problem concerning solar cells is the production costs. Electricity produced from fossil fuels and hydropower plants are currently much cheaper than the electricity produced from solar cells. Also, limited availability of silicon feedstock for the production of crystalline silicon solar cells is considered a major threat to the further growth of the PV industry. The present route for solar silicon feedstock goes from quartz, through metallurgical-grade silicon (MG-Si) and to electronic-grade silicon (EG-Si). The reject from the EG-Si production are further processed into wafers and solar cells. This situation is not satisfying, however, because it has created a silicon feedstock shortage and a PV energy price that is not competitive in a large scale.Crystalline silicon solar cells are the most important solar cells manufactured today. This will most probably remain the situation the next decade. Also, the future silicon ""feedstock"" is most likely not reject from the production of electronic-grade silicon, as it is today. There will probably be a more direct solargrade silicon route, excluding the very expensive electronic-grade silicon ""detour"". Quartzite has been regarded as the most suitable primary raw material used in the silicon solar cell production chain. This may change as the raw material requirements for the production of metallurgical-grade silicon are most likely to change. In addition, quartz or other silica-containing minerals from other rocks may be of a higher purity or contain lesser amounts of the most harmful elements. This favours increased beneficiation of primary raw materials in the future solar silicon feedstock production chain"

Jan 1, 2003

By G. Belardi, N. Shehu, L. Passeri

"This paper illustrates the possibilities of applying what is essentially a physical soil-washing technique for treatment of soil contaminated by semi-volatile hydrocarbons in order to reduce the level of pollution to that permitted by Italian regulations.The ground around a factory producing lubricating-oil additives consists of silty-sandy soils which have long been contaminated by heavy hydrocarbons, especially branched alkyl benzenes and naphthalene derivatives. Pollution is particularly marked in some zones (hot-spots) where Total Petroleum Hydrocarbon (TPH) values are as high as 7000 ppm. The hydrogeological characterization showed the presence of a gravely soil in a sandy/silty matrix, with big stones making preferential paths to the water circulation. The permeability is 10-5 m/s and the water-table occurs at about 3 m below ground level.After laboratory and pilot-scale studies on representative samples of in-situ soils with TPH between 2700 and 7000 ppm a flow-sheet is proposed for reducing TPH values below the acceptable limits in Italy, namely 700 ppm for hydrocarbons with more than 12 carbon atoms and less than 250 ppm for those with fewer.On the basis of indications provided by laboratory tests a mainly physical treatment process of soil washing has been developed. This is used to clean-up soil from a site polluted by non-volatile hydrocarbons with a high TPH value. The process involves a high-density attrition stage followed by wet screening at 0.5 mm and then wet-gravity separation of the minus 0.5 mm fraction in the centrifugal field.The gravity separation products consist of a light fraction with particle size finer than 15 micron which contains most of the pollutants, and a heavy coarse fraction with TPH values conforming to the limits set by Italian regulations (less than 700 ppm hydrocarbons whose structure contains more than 12 C atoms, and less than 250 ppm of hydrocarbons with less than 12 C atoms)."

Jan 1, 2003

By Briony C. Ruse, David V. Boger, Fiona Sofra1

"The sustainability of the mining industry must be addressed through improving tailings management. The use of thickened tailings and pastes stems from a paradigm shift towards designing tailings disposal sites to suit their surrounding environment, rather than manipulating the environment to accommodate the tailings. Thickened tailings and pastes usually exhibit non-Newtonian behaviour, so a thorough understanding of the rheological characteristics of the material is required in order to determine the disposal plant operating conditions.As environmental factors translate into economic issues, minimising waste production using dry disposal methods is gaining popularity. The use of rheological information is of high importance in evaluating the spreading characteristics, the transportation and the dewatering of thickened mineral tailings. The principles outlined may be applied to many industries encompassing a wide range of waste materials. The main obstacle to the widespread implementation of dry disposal methods has been the high initial capital cost of the methods due to the dewatering step, and the high cost of pumping thick suspensions across any great distance. Proper and thorough costing of tailings disposal activities combined with an accounting approach that shows closure and post-closure care costs on a per tonne basis of tailings disposed throughout the life of the tailings facility will show that dry disposal methods are more favourable than they might seem on initial appraisal."

Jan 1, 2003

By Natalie J. Shackleton, Deryck de Vaux, Cyril T. O’Connor, Vratislav Malysiak

"The major losses of PGM and base metals in the beneficiation of platinum group deposits occur during the separation of gangue from the value minerals by selective flotation. A number of studies have shown that this negative impact on flotation is due to surface passivation, caused by various ions that may originate from the external water supply or, as is likely in the majority of cases, from the oxidation of the mineral surfaces and the grinding media. The objective of the study was to investigate the effect surface passivation and inadvertent activation have on flotation and how this can be managed so as to increase the separation of pentlandite and pyroxene. The aim was to minimise the percentage pyroxene reporting to the concentrate and simultaneously maximise the pentlandite recovery. The testwork incorporates the addition of an activator (copper sulphate), a complexing agent, such as DETA (diethylenetriamine) and a dispersant (polyphosphate) at pH 6 and pH 9 in an attempt to alleviate the surface passivation of pentlandite and inadvertent activation of pyroxene. Both synthetic minerals and plant ores were studied in order to determine the effect surface passivation and inadvertent activation have on mineral surface alteration and floatability. Zeta potential determinations, microflotation, ToF-SIMS (Time of Flight Secondary Ion Mass Spectrometry) analyses, laboratory batch flotation tests and continuous flotation testwork were used as tools to study the surface alteration and/or floatability.Zeta potential determinations and ToF-SIMS analyses showed that copper adsorption is non-selective. Both pentlandite and pyroxene become copper (II)-activated in the presence of copper sulphate and subsequently, in the presence of xanthate, adsorption of the collector will occur onto copper activated mineral surfaces. Zeta potential determinations also showed an alteration of the surface charge in the presence of polyphosphate, thereby inhibiting surface passivation of sulphides by slime coatings due to surface repulsion."

Jan 1, 2003

By Stoyan N. Groudev, Ioannis Paspaliaris, Plamen S. Georgiev, Irena I. Spasova, Kostas Komnitsas

"The uranium deposit Curilo located in Western Bulgaria for a long period of time was a site of intensive mining activities including both the open-pit and underground mining techniques as well as in situ leaching of uranium. The ore was rich in pyrite and, apart from uranium, contained some non-ferrous metals. The mining operations in the deposit were ended in 1990 but since that time the deposit is a permanent source of acid drainage waters. The generation of these waters is connected mainly with the oxidation of pyrite and other sulphide minerals by the indigenous acidophilic chemolithotrophic bacteria.Laboratory and pilot-scale studies revealed that an efficient clean-up of the above-mentioned waters was achieved by means of passive systems of the wetland type. In 2001 a wetland was constructed in the deposit to treat a portion of the acid drainage waters which were discharged to a small ravine. This ravine reaches into the Teina, a small river that is a tributary of the upper reaches of the Iskar river.The wetland was constructed in the ravine and its bottom was located on intrusive rocks with a very low permeability. The rocks were covered by a 30 – 50 cm layer consisting of a mixture of soil, plant compost and crushed limestone. The wetland was characterized by an abundant water and emergent vegetation and a diverse microflora. Typha latifolia, Typha angustifolia and Phragmites australis were the prevalent plant species in the wetland but species of the genera Juncus, Eleocharis, Carex and Poa as well as different algae were also well present.The acid drainage waters treated by the wetland had a pH in the range of about 2.5 – 4.1 and contained uranium, radium, some heavy metals (iron, manganese, copper, zinc, cadmium, lead), arsenic and sulphates in concentrations much higher than the relevant permissible levels for waters intended for use in the agriculture and/or industry. The watercourse through the wetland covered a distance of about 0.2 – 1.0 l/s."

Jan 1, 2003

By Scott C. Brown, Ivan U. Vakarelski

The particles commonly encountered in mineral benefication schemes have irregularites that are expressed at many different length scales. In part, this originates from preceding processes (e.g. makedown, comminution, handling and storage), which are known to chemically and physically modify the bulk particle and its surface. Interparticle tribology, dissolution and reprecipitation events along with large-scale mechanical stresses are just a handful of the interactions encountered during processing of particles prior to separation. It is feasible to imagine that each one of these events may impose a fingerprint of characteristic nanoscale, microscale, and macroscale morphological changes that can modify the overall interaction of these particles within a system. Suprisingly there are just a few works on how these resulting features can alter the performance of benefication schemes, and especially flotation.

Jan 1, 2003

By Benoit Clermont, Jan Lux

"Magotteaux and Anglo Platinum started a co-operation program with the main aim of establishing the optimum milling configuration measured in terms of throughput, fineness and energy consumption.For this purpose, a fully instrumented pilot milling plant, supplied by Magotteaux (Pty) Ltd, and equipped with a 0.9 x 1.0 m ball mill, was erected at Frank concentrator (Merensky Pt ore). The primary ball mills at Frank concentrator were surveyed in order to set the conditions for the base case. This data was then replicated in the pilot mill under the same configuration. Thereafter, a series of different parameters were varied in order to attempt to optimize the milling system.Only grate versus overflow discharge and open versus closed circuit will be discussed in this paper.It should be noted that this paper does not attempt to give a universal solution as to what milling configuration is optimum in all cases. The conclusions apply for this particular case and probably most others, but it would be advisable to consider each case on its own.CONCLUSION• Overflow versus grate dischargeAn overflow mill has a “pool” of slurry around the toe of the ball charge, which creates a counter lever to the ball charge. This will reduce the absorbed power in the range of 10-15% (depending on the case) and will consequently result in a coarser grind. The tests found a 4% gain in grinding efficiency (Wio) with an overflow mill but this is probably not significant.This lower absorbed power and coarser grind can be counteracted by increasing the ball charge (if below maximum) and/or by increasing the mill volume when removing the grate discharge (a typical grate takes up about 300mm of the mill length).• Open versus closed circuit"

Jan 1, 2003

By Máximo Pérez, Julio C. Videla, Rosa Dzioba

"This paper reports the hydrometallurgical treatment of gravity concentrates of gold samples and outcrops associated with graphite ores obtained from:• flotation tailings of crystalline graphite minerals• outcrop samples of graphitic rock associated with auriferous minerals and free gold located in the Villa Union district and surrounding areas - La Rioja Province - Argentina.Previous studies of the flotation potential of crystalline graphite minerals failed to consider the presence of noble metals.The samples represent a mineralized zone of crystalline graphite which is distributed in different formations with a NE - SW trend in Maz, Punta Colorada and Las Ramaditas hills, covering an area of about 300 square kilometers."

Jan 1, 2003

By Gerke Gilian, Pretz Thomas, Pehlken Alexandra

"The evaluation of health hazards within the treatment of mineral and waste materials is gaining more and more importance in industrial countries. The need to control occupational safety has been recognised, and regulations which describe general protective measurements for personnel provide a tool to protect their health. It is the aim of the paper to give an outlook for practical approaches to risk assessment and to present measures for exposure reduction in accordance with the state of the art in Germany.Both the treatment of minerals and of waste materials are described in relation to the risk assessment. The method of evaluating health hazards in the two industries is similar and therefore both examples are presented next to each other.The example presented in the paper is the German “Biostoffverordnung” (the regulation for biological materials) which is important for the waste treatment industry. All kinds of waste treatment facilities (like composting facilities, waste dumps, sorting facilities for packaging materials) are obliged to carry out an assessment of health hazards for a variety of working areas and working places. The possible safety requirements deriving from this regulation are presented and discussed under the aspect of biological hazards.All over the world each country has different guidelines and regulations but all have one target in common – to protect the employees. This can be achieved through a good management system of occupational health and safety. Therefore the health hazards have to be known and assessed.Principles of the assessment of health hazards are described through:Data collection on siteData evaluationAssessment of health hazardsDocumentation"

Jan 1, 2003