Search Documents

By Olli Haavisto, Heikki Häkkänen, Tommi Kauppinen, Navid Khajehzadeh

Raman analysis is a well-established method for finding the abundant minerals in an ore sample. In this study, Raman spectroscopy is tested as a method for rapid and contactless on-line mineral analysis. Rapidness might enable on-site analysis of rock drillcore, which in turn would lead to more cost-efficient solutions in mineral exploration. This paper discusses the use of Raman analysis to identify minerals and to measure their concentration. The sample set under study consists of rock drillcore collected from Agnico-Eagle Kittilä Mine, Finland. Selected parts of the sample set are measured by Raman spectroscopy and the minerals are identified using reference spectra from a public source. Moreover, the direct measurement of concentration of different minerals with the help of Non-negative least squares (NNLS) optimisation algorithm is considered. The optimisation algorithm was constructed to form a linear combination of reference spectra which best represent the measured spectrum, or an average of measured spectra, from an ore sample. The results show that NNLS can identify abundant minerals in a given sample. Also through this method of analysis the results of a traditional point-count method can be expanded: It was observed that, due to grain size, multiple minerals consistently appear in the spectra measured over an area, which means that point-count method is not a proper way to interpret the spectra. This can be seen as a new result, as formerly the discussion has attended to other methods.

Jan 1, 2014

By Wolfgang Öfner

Many technical processes also yield dusty residues which usually contain appreciable amounts of valuable matter. Often they also accumulate substances detrimental to the process. Dumping them entirely in landfills wastes raw material and causes high disposal costs, but recycling them without prior treatment is often not feasible. Physical separation processes are preferable because of their rather low energy demand. In order to develop such treatment systematically, the residues must be characterized properly. The technique for such a characterization is taken from mineral processing: perfect fractionation according to continuous properties of the particles supplemented with chemical analysis are used for plotting the Henry-Reinhardt chart. This represents the benchmark for assessing actual separation processes and tests. Their results are compared in terms of ?selectivity? and plotted in the kappa chart. In this paper, Henry-Reinhardt chart and kappa chart are applied to several different types of residues from iron and steel production and show their potential for being upgraded before reutilization in the production process. This approach is suitable for virtually all dusty residues from other industrial processes as well. Keywords: residue, dust,iron and steel, process development, Henry-Reinhardt chart, kappa chart

Sep 1, 2012

By Xiao Jian Li, Dai Xiong Chen, Jian Wen Yang

In one kind of lead and zinc bearing polymetallic ore containing secondary copper, the characteristic of low sulfur, high zinc, and particularly the existing of secondary copper minerals can lead to lead concentrate with high content of zinc because the dissociation of Cu2+ in the grinding process may have an activation influence on sphalerite. Considering its process mineralogy analysis, a new process of seperation of lead and zinc has been put forward. The experiments focused on the analysis of the advantages and disadvantages of the inhibition effect of traditional adjustment reagent + zinc sulfate on activated sphalerite compared with new organic inhibitor, polysaccharide xanthate. According to the numerical calculation and test results, a reagent system of polysaccharide xanthates is developed, which has a good inhibition effect on Cu2+ activated zinc minerals, achieving high-efficiency separation of lead and zinc. A new reagent system and flotation process was developed under optimal conditions. Under the condition of the run-of-mine ore containing 2.37% Pb and 12.48% Zn, lead of 67.69% grade and lead concentrate with the recovery rate of 86.06%, zinc of 60.32% grade and zinc concentrate with the recovery rate of 96.15% were achieved.

Jan 1, 2014

By W. S. Eu

Thermal treatment of mineral ores can initiate thermal phase transformations which can affect either their activation or deactivation, subsequently influencing their ability to dissolve in a leaching reagent. The formation of rutile and hematite from ilmenite minerals, for example, has been suggested to occur through a series of reduction and segregation reactions. This process has been used in beneficiating low-grade weathered ilmenite ores to higher grade rutile. Despite decades of re-search, the mechanism of this process is not well understood, because dissolved intermediates are poorly crystalline and are difficult to quantify, with the exception of the final rutile products. Previous studies have shown that disrupted intermediate phases, by thermal treatment, are most susceptible to reagent attack and can often demonstrate ?activation? effects. In this study, synchrotron based X-ray diffraction method was used to investigate in-situ and in real-time the transformation of ilmenite minerals to rutile and hematite during calcination. The rate of formation and disappearance of specific Bragg peaks during the reaction and thermal decomposition of the mineral were used to derive an understanding of the solid-state reactions. The effects of the mineral transformation were validated by laboratory based batch calcination and leaching in sulphuric acid. The results suggest that transformation of major mineral phases occurs within of specific window of operation and thermal treatment appears to influence the extent of activation and leachability of ilmenite minerals.

Jan 1, 2014

By N. Tsoni

The separation and recovery of fine and ultra-fine particles during the processing of mineral commodities by conventional separation methods is difficult and inefficient. This is due to the problems posed by the very small size of the mineral particles. The fine and ultra-fine mineral particles are either generated during size reduction processes or are necessitated by liberation size. This problem is expected to deteriorate, as deposits of even lower grade are processed. The inefficiency of the conventional separation methods with regards to the processing of very fine particles leads to the loss of considerable quantities of mineral commodities to the tailings. Novel methods and techniques as well combinations of known methods have been tested over the years. Among them, selective aggregation, along or in combination with flotation, has been given much attention. This study deals with the application of hydrophobic agglomeration as a separation method for very fine particles. The selected mineral system is magnesite/quartz, due to its sensitivity to physi-cochemical separation methods. The aim was the selective agglomeration of magnesite using sodium oleate. Tests on single minerals revealed that separation seems feasible and efficient. The parameters examined were: pH, quantity of sodium oleate, conditioning time, and, finally, settling time. Tests carried out on artificial mixtures of the two minerals, under various proportions, confirmed the results obtained from single mineral tests but they were slightly inferior. Finally, hydrophobic ag-glomeration tests were carried out on single and artificial mixtures of minerals using sodium oleate and petroleum as reagents. The results show that the addition of petroleum improves the results. In conclusion, hydrophobic agglomeration can be applied successfully even for fine particles of difficult-to-be-separated systems such as magnesite and quartz.

Jan 1, 2014

By A. Saramak

"The paper focuses on problems of atmospheric pollution by the dusts, produced during the course of crushing and grinding processes, and the main objective of investigative programme is an assessment of emission of particulate pollutants for following crushing devices operated in plant scale: impactors, cone and jaw crushers. All crushers operate in aggregate production plants in Poland. In the first stage of investigations there were determined dust emission levels and supporting characteristics for all crushers under investigation. Then there were introduced indices that allow for comparative analysis in terms of dust emission, for devices with different energy consumptions and comminution ratio. It appeared that crushers with high the overall dust emission do not always achieved unfavorable dust emission per comminution ratio or energy consumption. The introduced indices proved their usefulness, because they helped to carry out a comparative analysis among crushers, operating under different technological conditions. It is also easier to assess environmental impact of individual crushing devices, under analysis. Results of investigations also show that environmental impact of different types of crushers is diverse and it is difficult to compare dust emissions of various types of crushers without taking into account technological aspects (like throughput, comminution ratio, energy consumption, and others) of their operations.INTRODUCTION Mineral processing of raw material is a complex process, involving in general operations of size reductions and separation. Depending on the type of specific raw material, the technological circuit may include operations of comminution and size classification. This is a typical circuit for aggregate production. In ore treatment industry the process in much more complicated and include also a metallurgical treatment of ore concentrate – the final product from processing plant stage.In general, regardless the type of raw material, operations of size reduction are present in each technological circuit of mineral processing. Operations of crushing and grinding are an integral part of processing technology, because they play a crucial role in effective treatment of mineral raw materials (Gawenda 2013). Their duty is to liberate the useful minerals from the gangue in ore treatment industry, or to produce the material with the required particle size in case of aggregate processing. Crushing and grinding operations are of a high negative impact on environment and humans. They consume great amounts of energy, what indirectly contributes to higher emission of carbon dioxide CO2. Apart from energy, crushing and grinding device consume significant amount of steel and other metals and alloys due to high wear of working parts and grinding media. This is also of negative environmental impact due to emissions of additional amounts of CO2 in production of steel and other metals required as spare parts for comminution devices."

Jan 1, 2018

In the present work, the influence of coagulant, polymeric flocculant structure type and mode of addition on flocculation performance and dewatering behaviour of plant mineral waste tailings of diverse mineralogy (kaolin, quartz, goethite/hematite feldspar, gibbsite, rutile, and Illite) is investigated. High molecular weight, non-ionic polyacrylamide homopolymer and anionic (acrylate) and cationic (quaternary acrylate) copolymers were used in orthokinetic flocculation of colloidal-ly-stable, aqueous dispersion of negatively charged particles. It is demonstrated that, through prudent selection and mode of addition of polymer structure types, synergistic effect between certain cationic and anionic flocculants can be readily achieved, leading to significantly improved dewaterability of the heterogeneous mineral waste tailings.

Jan 1, 2014

By Francisco Vicuña, Miguel Becerra, Nelson Iglesias

"The following article presents the development of a dynamic tool for the estimation of Jb/Jc rate (ball filling level / total load filling level) of a SAG mil operating in a single stage mode. Using the methodology detailed in this article, it is now possible to have a dynamic estimation tool in the operation, which enables strategic decision making and achieving a continuous development in process optimization. The estimating of the load filling level (Jc) was conducted using a power model, which in this case corresponds to the C-Model developed by (Morrell, 1993) that was calibrated by measuring the load filling levels (Jc) and balls (Jb) using the FARO laser scanning technology by means of Grind-Out and Crash-Stop procedures during the year 2013 and 2014. Finally, to estimate the dynamic filling level of full charge, Jc, three independent models were developed that allowed to feed the adjusted power model: •,SAG mill discharge grate slot wear model •,SAG mill internal volume wear model •,Ball filling level estimation model."

Jan 1, 2014

By Z. Chen

This study is concerned with the behavior of bubble clusters in a well-controlled turbulent flow. We used a specially designed cell where the bubble aggregates could be formed and exposed to breakage by a rotating impeller. The effects of impeller speed and the concentration of collector on cluster behavior were studied. It was found that the size of the clusters increases with the concentration of collector used. We also found that although the clusters could easily be destroyed under the action of impeller, they could reform, especially at lower impeller speeds. It was observed that the size of the bubbles arriving into the impeller region in the absence of particles before breakage was considerably higher than the size of the clusters formed at the same impeller speed. It appears that both cluster breakage and re-formation take place simultaneously, and the extent of formation and regrowth is mainly determined by the hydrophobicity of the particles and the impeller speed.

Sep 1, 2012

By Áureo Del Vecchio, Lídia Dely Alves de Sousa, José Pereira

The potassium demand for agriculture purposes has increased in Brazil, which has great deficit of internal demands. Potassium-rich rocks have been used as fertilizers as technological alternatives for agriculture aimed to reduce the amount of chemicals and the sector dependence for such products. Vermiculite tailings from União Brasileira de Mineração - UBM, at Santa Luzia - PB, was studied aiming their application in agriculture by potassium release. The sample was analyzed by XRF and XRD; studies on release kinetic with particles smaller than 2 mm added of organic acids (citric and oxalic) at 10-2 mol/L concentration; samples were analyzed by XRD after kinetic assays. The work was conducted using a shaker incubator at 300-rpm agitation and time variation to better understand the potassium availability in the ground. Results show the presence of K2O at 3.46% concentration. Citric and oxalic acids increased the release speed to almost the same level with speed coefficients (k) of 2.61x10-2 h-1/2 and 2.55x10-2 h-1/2 respectively. In statistical terms for both acids, the linear equation represents more than 99.0% of the experimental assays. Stonemeal was applied to banana seedlings in experiment conducted in a greenhouse. The use of vermiculite tailings in banana seedlings promoted potassium absorption, which influenced its growth. The amount of potassium liberated from vermiculite tailings could be used as a long-term alternative to fertilizers in agriculture cultures.

Jan 1, 2014

By M. F. He

The depression of pyrite in marmatite flotation by a new depressant Sodium Glycerine-xanthate (SGX) has been investigated through microflotation, zeta potential, and adsorption measurements in systems open to the atmosphere. The flotation tests of single mineral show that in the presence of SGX, marmatite can be activated by Cu2+ and shows good flotability, while pyrite can?t be activated and therefore shows poor flotability, as a result these two minerals can be separated using butyl xanthate as the collector. The depression mechanism of SGX on sulfide minerals is discussed based on Zeta potential and adsorption isotherm. Zeta potential experiments demonstrate that at the presence of Cu2+, SGX can strongly adsorb on the surface of pyrite, while it can?t adsorb on the surface of marmatite, thus the results are in accordance with those of flotation experiments; the results of adsorption isotherms show that the adsorption density of SGX on pyrite is greater.

Jan 1, 2014

By Grigory Voyloshnikov, Sergey Petrov, Vladimir Petrov

"The treatment of high-grade copper gold-bearing ores is practiced extensively. However, due to low concentration of copper the application of a separate process for copper recovery can make this process uneconomical. The copper, in particular: in oxide minerals, intensively bounds with cyanide during conventional cyanidation. In this case, cyanide is not able to react with precious metals and the consumption of cyanide increases. The resulting copper cyanide complexes have a negative effect on the recovery of gold. Due to decreasing of the process parameters, a repeated use of the recycled solutions can be hindered, especially in the case of heap leaching. The technology of copper removal from the process solutions with simultaneous regeneration of free cyanide from copper-cyanide complex and producing of a saleable high-grade copper concentrate was developed. An important feature of this technology is simplicity, the absence of complex or dangerous operations and the use of common reagents. The choice of equipment depends on the ore treatment option: heap or vat leaching. Also, simpler equipment schemes are available. The studies, tests and industrial practice show that if the concentration of copper can be decreased down to the first numbers of mg per ppm or lower, it is reasonable to maintain the process copper grade in the recycled solutions at 30-50 mg/L. In this case, recycling of cyanide-bearing solutions is unlimited. The regeneration of free cyanide from that of bound with copper and other cyanide complexes is 95-98%. The grade of copper in the concentrate is 55-60%. This technology is an economically competitive option, in particular: with the account of the sales of copper concentrate. The removal of copper has a positive effect on gold recovery, especially during heap leaching. In addition to, this offers significant benefits in reduced costs."

Jan 1, 2014

By J. Leite

In a small-scale mining in Brazil?s northeast, scheelite were exploited since 1940?s using a traditional gravity concentration flowchart (composed by jigs and shacking tables) that operates with low efficient for fine particles. Tailing of this plant was submitted to chemical, mineralogical and size characterization. Results pointed 50% smaller than 74µm with a grade of 0.11% WO3. The particle?s size is an important operational variable to heighten recuperation by shacking tables. Tests using Falcon SB40 centrifuge concentrators and shacking table were realized, optimizing their operational variables. Based on the tests results a new flowchart was proposed for concentrating and tailings recovery.

Sep 1, 2012

By S. Gaydardzhiev

Laboratory batch tests having preliminary and orientation character aiming at improvement of the molybdenum flotation at Ellatzite copper processing plant in Bulgaria have been conducted. The following technological parameters have been screened to study their influence on the grade and recovery of copper and molybdenum during the rougher flotation stage: flotation pulp density, pH, addition of secondary collector and replacement of MIBC by pine oil as a frother. The results have shown that slightly better grade/recovery figures could be obtained for both copper and molybdenum at lower flotation pulp densities. The addition of kerosene has improved the recovery of molybdenum however, on the expense of that of copper. The effects from pH variation and the replacement of MIBC by pine oil as a frother have been almost negligible.

Sep 1, 2012

By Xu Wang, Bang Chen, Xiujian Luo, Wei Tang, Xiao’ou Xia, Fangming Liu

"The inertia cone crusher has lots of advantages, such as big crushing ratio, fine particle size, material layer crushing, good passing tramp iron performance and stable technical index, realized open crushing circuit and simplified crushing flowsheet. The crusher was input to China’s Beijing General Research Institute of Mining and Metallurgy (BGRIMM) from Russia’s Mekhanobr-Tekhnika Research & Engineering Corporation at the beginning of the 1990s. This paper introduces that after years of absorption and innovation how Chinese researchers optimized and creatively designed about transmission mechanism, bracing structure, kinetic parameters, lubrication system, dust sealing system, damping system and hydraulic control system etc on the basis of keeping its advanced theory and unique structure, therefore the crusher’s stability was raised and the usage cost was reduced greatly. Accordingly the inertia cone crusher in China has been widely used in many fields, such as mineral resources and the recycling of metallurgical slag. The achievement in cooperation was fully affirmed by governments of Russia and China, and cooperation of science and technology in the mining and metallurgy industry between Russia and China is promoted greatly. INTRODUCTION From the early 1950s, the former Mekhanobr Institite(now Mechanobr-Tekhnika Research & Engineering Corporation) devoted itself to the research of inertial cone crusher and put it into industrial application in the late 1980s. Inertial cone crusher is like a maverick flower in the field of crusher. With its excellent performance and excellent application effect, it shocks the world and is destined to shine with a bright future. In the early 1990s, the chief leaders of the Beijing General Research Institute of Mining and Metallurgy (BGRIMM), Academician Sun Chuan-yao and Professor Zheng Baochen, captured the extraordinary performance and strong vitality of inertial cone crusher with keen eyes. So the two big institutes started the cooperation to introduce inertial cone crusher to China. Since then, Inertia cone crusher has been able to flourish in China and have achieved impressive results with two institutes’ continuous effort."

Jan 1, 2018

By N. Vasumathi

Most of the Iron ore washing plants set up in India in the earlier days consist of sizing of the ore by dry / wet screening, washing and classification by screw classifiers. In this classical approach, iron values were lost in the form of fines and ultrafine into the tailing ponds as they had little commercial value in those days and accumulated in huge quantities over the years. As the high grade deposits are getting exhausted and the demand for high grade finer material for pellet making is ever increasing, focus is shifting towards recovering the values from the erstwhile tailing ponds by column flotation. This is also supposed to mitigate to a certain extent the environmental problems caused by the ever expanding and unmanageable tailing dams. A case study is presented wherein a composite sample is prepared from samples drawn systematically from multi - locations in a sprawling tailing dam. Laboratory scale column flotation tests on this composite tailings sample, basically originating from two operating iron ore beneficiation plants of JSW Steel Ltd., one of the leading producers of steel in India are found to be encouraging. Desliming followed by reverse and cationic flotation tests using flotation column resulted in the concentrate of 61.88% Fe, 4.81% SiO2, 2.52% Al2O3 and 3.30% loss on ignition (LOI) from the tailings analyzing 57.86% Fe, 7.10% SiO2, 3.52% Al2O3 and 6.14% LOI with 52% weight recovery. The causes for the quality improvement could be attributed to desliming of un-liberated ultra fines of kaoline and hydrated iron oxides and their further reduction by efficient flotation process. The process and the cationic collector developed for this purpose are adopted in the new flotation plant created to treat these tailings. Keywords: iron ore, washing, ultra fines, tailings pond, column flotation

Sep 1, 2012

By Rodrigo Carvalho, Marcelo Tavares

"The accurate prediction of the outcomes in SAG grinding has been a great challenge to researchers and process operators. The use of Discrete Element Methods for modelling charge motion in tumbling mills allowed extraction of not only visual data, such as the position of the charge, but also the energy transfer in terms of the energy dissipated in the collisions. One of the advantages of DEM technique is its scalability to different mill sizes and some operational conditions such as speed and mill filling. Recently the Authors proposed the coupling between DEM outputs and modified Population Balance Models that with proper dedicated ore characterization tests allows the prediction of the outcomes of an energy transfer example. This modelling framework is called the Multi-scale Mechanistic Modelling. This paper shows the application of the Multi-scale Mechanistic Model to a set of pilot plant tests ran at different operational conditions. The prediction of the grinding outcomes and even the stabilization of the charge was achieved by the use of the Multi-scale Mechanistic Modelling framework. This approach has a great potential to become a powerful tool to design and optimize AG and SAG mills."

Jan 1, 2014

By Adam Jordens, Olga Kuzmina, Christopher Marion, Kristian Waters

"In order to meet the growing demand for non-Chinese rare earth suppliers many new rare earth (RE) mineral deposits are currently under development, however these deposits typically include many minerals for which there is little processing information available. One of these deposits is the Nechalacho deposit located in the North West Territories of Canada. This deposit contains multiple RE minerals including bastnäsite, zircon, fergusonite, allanite and monazite. The work presented here investigates the use of different classes of flotation collectors (carboxylic acids, hydroxamic acids, phosphoric acids) typically used in RE mineral flotation to float the Nechalacho ore directly. Flotation tests are also conducted as the final step in a beneficiation process incorporating centrifugal gravity concentration and magnetic separation. This combination of centrifugal gravity concentration and magnetic separation rejects low specific gravity gangue minerals such as K-feldspar and plagioclase and concentrates high specific gravity minerals such as magnetite and hematite. The removal of low specific gravity gangue helps to improve flotation and the removal of ferromagnetic iron oxides is important prior to flotation using certain chelating collectors."

Jan 1, 2014

By Chiharu Tokoro

Acid Mine Drainage (AMD), high acid water containing heavy metals discharged from mines, has been recognized as major cause of mine pollution. In Japan, the government spends billions of yen every year to prevent pollution caused by AMD in about 80 abandoned mines. It is widely recognized that the treatment could continue for long decades or an even century. However, costs and environmental loads are uncertain during the treatment because a predictive model for the quality of AMD, the dosage of neutralizer, and the amount of sludge that is applicable for abandoned mines with limited data has not yet been established. In this study, a two-steps predictive model for solution composition and neutralization chemical requirements of AMD in future was constructed based on the geochemical modeling. Requisite input data of the model was the past historical water quality data from AMD monitoring, such as metal concentration and pH in the solution, instead of the sample rocks as other conventional prediction methods. In the first step, solution composition of AMD in the future was extrapolated from the available historical data using geochemical simulation considering the first order kinetics for the mineral dissolution. In the second step, neutralizer dosage and sludge generation in the future was predicted based on the geochemical simulation supposing the chemical equilibrium and oxidation state for all of elements in the solution. Based on case studies of two abandoned mines in Japan, solution composition, neutralizer dosage and sludge generation were estimated. The results of this study demonstrate the effectiveness of our model for the prediction of AMD quality and chemical requirements of neutralization treatment after mine closing. The model is useful for the estimation of the neutralizer dosage and the sludge volume in abandoned mines with limited data. Keywords: acid mine drainage, predictive model, geochemical modeling, first order kinetics, water monitoring

Sep 1, 2012

By P. Somasundaran, Tarun Bhambhani, S. Murthy Khandrika, Partha Patra, D. Nagaraj

Fine and ultrafine mineral particles, particularly if, altered mineralogically, can have detrimental effects on selective separation of minerals. Behaviour of altered mineral fines has been investigated in this work by studying the effects of weathered silicate slimes on the selective separation of copper minerals, particularly with focues on effect of the pulp rheological behaviour, which plays a governing role in the process. Physicochemical properties of these altered silicates fines such as morphology and surface charge are proposed to be responsible for the adverse rheological effects and resultant selective separation. Here, the effect of a number of problematic aspects such as water chemistry, froth stability, physicochemical aspects of gangue mineral aggregates on flotation sub-processes has been studied. Processing problems owing to the physical aspects of the gangue minerals, shape and morphology, are primarily due to uncharacteristic increase in the pulp viscosity. While problematic aspects other than impact of pulp rheological behaviour can interfere with each other in their contributions to how they affect the sub-processes, effects owing to pulp rheological behaviour have a direct impact on the flotation performance. Subtle increase in pulp viscosity can interfere with sub-processes in flotation leading to decrease in recovery and grade, and it is difficult to assess the effects due to such subtle changes. Reagent based strategies to overcome the problematic aspects has been explored here.

Jan 1, 2014