Search Documents

By Andrzej Tejchman

A method of improvement of a subsoil under bored pile base by injection is presented. The method employs a special chamber attached to the reinforcement at the bottom of the drilled borehole. The chamber is made of semi-permeable textile bag. The injection entered under high pressure into the bag, causes prestressing of subsoil under the pile base. The results of load tests of piles improved in this manner have shown a substantial increase of their capacity together with simultaneous reduction of settlements. This technology has been implemented for four constructions such as trestle bridges in Gdynia and Warszawa and the bridges in Szczecin and Gdansk. The injection effects are shown based on the load test results.

Jan 1, 2002

By Florian König

It is well known that the bearing capacity and stiffness of displacement piles may increase significantly with time, a phenomenon usually referred to as set-up. In cohesive soils the set-up is commonly explained by consolidation processes in which the dissipation of the excess pore pressures around the pile leads to an increase in effective radial stresses. Recent case histories show that set-up may also occur in sand over a period which exceeds by far the consolidation process. Therefore, other effects apart from the dissipation of excess pore pressures must contribute to this long-term set-up effect. This paper presents the results of a series of multiple pile load tests on prefabricated concrete piles which capture the effect of pile set-up empirically. The main characteristics of the set-up trend are shown with respect to soil type, pile dimensions and distribution over the pile length. Possible reasons for pile set-up like consolidation and stress relaxation after the end of driving are examined using a finite element model which simulates the pile installation process.

Jan 1, 2006

By Filippo Maria Leoni, Wesley Schmutzler, Matteo Bertoni

"Deep Mixing Method (DMM) for the Rio Puerto Nuevo Project (Project) in San Juan was chosen by the Corps of Engineers to improve the soils adjacent to a 92 inch ID forced sewer main relocation and to improve the soils for the base of a new drainage channel. The soils to be improved consisted of sandy fill, soft clays, organics and stiff, plastic clays. A pre-construction soil investigation campaign, followed by a Bench Scale Mixing Programme and a Full Scale Field Test were performed during the pre-construction stage to assess soil properties, select binder type and dosage, and disclose the most suitable combination of injection parameters to improve the different soil layers. Production started at the end of August 2012 and was completed in October 2013; over 3,000 DMM elements were installed to a maximum depth of 57 ft below ground for a total gross volume of approximately 125,000 cubic yard. Each element consisted of two 5.5 ft diameter overlapping columns installed simultaneously, and their layout was such to meet the 100% Area Replacement Ratio required by the design. The ground improvement was successfully completed despite some difficulties due to a considerable amount of obstructions. Wet grab sampling and UCS testing of the retrieved specimens were designed as the main QC/QA method for the verification of the quality of the ground improvement. Upon completion of production, approximately 3,000 specimens were cast. The contract also required continuous coring of at least 12 randomly selected DMM elements and the testing of 8 cored specimens per bore for strength assessment. This paper will illustrate means and methods used in the field to construct the designed ground improvement and the results of the QC/QA program, with a focus on the differences between wet grab and coring sampling methods.INTRODUCTIONThe Rio Puerto Nuevo project involved the stabilization of a major drainage channel using the Deep Mixing Method (DMM), and the relocation of a 92 inch ID forced main sanitary sewer outfall. Previously, in 2004, a 40 x 16 x 2,000 ft. box culvert was installed under a different contract to convey runoff waters to the ocean.However, the connection between this culvert and the upstream network of channels was not constructed due to the presence of the forced main sewer pipe. In order for the drainage system to be completed and function properly, the 92 inch ID forced main needed to be lowered about 20 ft to allow for proper drainage.DMM was chosen by the US Army Corps of Engineers to stabilize the drainage channel as well as improve the soil under the relocated sewer main. The DMM was arranged in different zones (A through E) with variable top and bottom design elevations as can be seen in the typical cross section for Zone A (deeper and with a higher strength requirement) and Zone B as an example (Figure 1)."

Jan 1, 2015

By A. A. Gupte

Auger piling system which was developed in the United States in the 1940's is gaining acceptance in many parts of the world. Although primarily used to support foundations, the system is very useful for many other applications such as soil anchors, temporary and permanent earth retention systems, restricted headroom piling and underpinning of existing foundations. In this paper, review of current construction design techniques for the Auger piling system for earth retention and underpinning of structures is presented.

Jan 1, 1989

By Ali Azizian, Brian Hall

"Driven piles were selected to support the Fraser Heights Bridge bents. Piles were a key component of the top-down construction approach, which was adopted for minimizing potential impacts on an environmentally sensitive wetland. Project requirements mandated verification of pile capacities using dynamic methods. More than 40 Pile Driving Analyzer (PDA) tests were performed. The subsurface conditions were highly variable. On the east side, piles extended through loose sands, soft silts/clays, and two peat layers and were founded in glacial till-like soils at about 45 m depth. However, on the west side, till-like materials were so shallow that it was difficult to drive the piles sufficiently deep to obtain the necessary lateral support. This paper provides an overview of the geotechnical considerations of the bridge design and top-down construction approach, and expands on the presentation of PDA results and how they compared to pile capacity estimation methods and parameters recommended in the applicable design codes.INTRODUCTIONThe Fraser Heights Bridge (FHB) was a component of the Fraser Heights Connector (FHC), a 2 km section of the South Fraser Perimeter Road (SFPR), constructed as part of the Port Mann/Highway 1 (PMH1) Improvement Project. The FHC is located in northeast Surrey BC (Fig. 1).Two major design and construction determinants were: 1) a mandated tight schedule to provide a non-tolled alternative to a new toll bridge; and, 2) an obligation that construction had to occur with minimal impact on the environmentally sensitive wetland the FHB crossed, including limiting the footprint of the permanent and temporary works to less than 45 m2, and prohibiting construction access onto the wetland. Construction equipment was only allowed on the wetland on temporary trestles or on the finished structure. This latter requirement resulted in the bridge being constructed span by span, using a top-down approach."

Jan 1, 2016

By Edward Jacobsen

The Oak Creek Power Plant in Oak Creek, Wisconsin is currently undertaking an expansion project. In order to supply cooling water to this facility, a 27' (8.2m) diameter tunnel will be bored, in rock; to connect to 4 vertical Intake shafts located approximately 1.5 miles (2.4km) offshore in Lake Michigan. In 2004, Case Foundation Company was awarded a lump sum contract to Install these intake shafts. When complete, the plant is expected to circulate upward of 2 billion gallons per day (7.5 billion liters) through this system. Two shafts were drilled in a (shortened) construction season in 2005 and the remaining 2 shafts and 4 liner assemblies were completed in 2006. Future connection to the tunnel, in 2007, will be accomplished by mining upward to reach the lower portion of each liner and then removing its internal bulkheads to permit the flow of the lake water into the tunnel.

May 11, 2007

By Fred Tarquinio, Giovanni Bonita, Lars Wagner

"A new embassy for the Peoples Republic of China is under construction in Washington, DC. The 475,000 square feet (44,125 m2) structure has five levels below ground and four above, making it the largest embassy in Washington DC. A vertical soil nail wall was used as the primary support of excavation system for the project. The soil nail wall was irregularly shaped, benched in areas, and up to 98 feet (29.9 m) in height. The soil nail and shotcrete system consisted of approximately 1,600 soil nails and 50,000 square feet (4,645 m2) of exposed shotcrete wall surface. Design and construction challenges included soft soil conditions, inside wall corners, underground utilities, seismic impacts from blasting, and logistical and political factors. Overall, wall movements were lower than expected, with maximum horizontal movement less than 0.25% of the total height of the excavation.INTRODUCTIONThe proposed Embassy of the Peoples Republic of China in Washington, DC, will consist of about 475,000 ft2 (44,125 m2) of building space and contain up to four fl oor levels above ground and fi ve levels of basement (Figure 1). When completed, the building will be the largest embassy in Washington, DC. The architect for the project, Pei Partnership Architects, along with the world-renowned architect I.M. Pei, made effi cient use of the site by inserting the building into the existing slope. Consequently, excavations reach heights up to 98 feet (29.9 m) on the southern side of the property and 42 feet (12.8 m) on the northern side.The soil nail and shotcrete system consisted of approximately 1,600 soil nails and 50,000 square feet (4,645 m2) of exposed shotcrete wall surface. The location of the building relative to the property line called for tight excavation requirements, including precise wall positions and shotcrete tolerances. Design and construction challenges included soft soil conditions, inside wall corners, arched walls, underground utilities, seismic impacts from blasting, and logistical and political factors.SITE INVESTIGATIONInformation obtained from the geotechnical investigation revealed about 10 to 20 feet (3.1 to 6.1 m) of a loose to medium dense fi ll material placed during previous site activities. The fi ll material was underlain by a silty sand and sandy silt residual soil derived from the natural weathering of the underlying bedrock. This soil sequenced naturally from a medium dense to very dense material through natural weathering of the underlying bedrock. This soil sequenced naturally from a medium dense to very dense material through natural weathering processes in the rock. The underlying bedrock was locally characterized as a gneiss. A water table elevation about 17 feet (5.2 m) above the fi nal excavation level was revealed, except in the “radius” area, where a leaking water main/hydrant generated a high local water table."

Jan 1, 2007

By Xiaocen Lu, Guowei Li, Jiantao Wu, Thang N. Nguyen, Andrew C. Amenuvor

"This paper investigates the effect of driving a group of 52 open-ended Prestressed High Strength Concrete (PHC) piles on an existing highway embankment based on field measurements of excess pore pressure and lateral soil displacement. Excess pore pressure due to pile driving increased with depth and decreased with increasing distance from the pile, influencing a distance of 43 pile diameters. For pile groups, the rate of dissipation of excess pore pressure decreased with increasing depth and averaged 79% in 20 days, during which maximum ultimate bearing capacity was not yet attained. Lateral soil displacement continued to increase for a period of time after the end of pile driving and this could have resulted in significant inclination of piles if pile installation was too quick and pile spacing was too small. Lateral soil displacement due to pile group decreased with decreasing distance to the existing embankment as a result of high soil density produced by the embankment loading. The results also indicate that the effect of pile group installation on the existing embankment is negligible.INTRODUCTIONPile driving can cause excessive lateral displacement of soil and heaving of the ground surface, which may adversely affect nearby structures. In addition, lateral deformation and excess pore water pressure resulting from pile driving can exert lateral pressures and vertical forces on the piles, and impact negatively on the project and its surroundings. Therefore, it is important to evaluate the influence of pile driving on the nearby structures as well as the project itself when expansion works are carried out.Recent years have seen some development in the application of field tests for studying soil disturbance due to piles, and these tests usually involves pore water pressure and lateral soil displacement monitoring during pile driving. Results of field experiments performed by Reese and Seed (1957) in San Francisco Bay Mud with instrumented piles showed that pile installation generated large pore water pressures at the pile surface, with only slight increase at a distance of 15 pile diameters away. The measurements indicated that the increase in pore water pressures can exceed the initial total overburden pressure. Holtz and Lowitz (1965) reported a decrease in undrained shear strength immediately after pile installation, which was largely recovered after full pore pressure dissipation for field measurements within 1.5–2 pile diameters from the pile surface. Hwang et al. (2001) presented results of large scale pile driving tests where maximum excess pore water pressure generated decreased rapidly with increasing distance from pile. The excess pore water pressure became negligible at 15 pile diameters from the pile. Their results also showed that lateral displacement of the ground decreased with increasing distance from the pile. Pestana et al. (2002) carried out full-scale closed ended pile tests in the Young Bay Mud deposit. Higher excess pore pressures were observed for points closer to the pile, which decreased with increasing distance from the pile wall. Exponential decay of excess pore pressure with time was also noted. An 80% dissipation of excess pore pressure was achieved for soils more than one pile diameter away from the pile wall between 50 to 80 days. Lateral deformation generally decreased with increasing distance from pile wall, whilst varying erratically with depth. Bozozuk et al. (1978) reported on soil disturbance due to driving of 116 concrete piles in sensitive marine clays in a construction project. Maximum pore water pressures after pile driving within the group, and 6m (20 pile diameters) from the group were over 35-40% of the total overburden pressures, and the influence of pile driving on pore water pressure at 20m away from the group was very small. Cooke and Price (1973) studied a 168-mm-diameter instrumented pile jacked into over consolidated London clay. Outward lateral displacements ranging"

Jan 1, 2016

By Anup Kumar Mandal, Sanjoy Chowdhury, Biswajit Das

"Tailing pond of an iron ore mine necessitated raising the height of its embankment to create additional storage capacity. The tailing pond is located in eastern India and raising the height of embankment was going on during the month of January, 2014. Upstream method of construction was adopted since there was no space available at the downstream side. During the construction, about 200 m stretch of the north east embankment of height about 5.5 m failed forming a classical slip circle on the upstream side involving about half the top width of the embankment. To find out the root cause of the slope failure, detail geotechnical investigation work was carried out within the embankment as well as in the adjacent areas within the pond. About 7.5m thick very soft tailings were detected below the constructed embankment. Shear strength of the soft tailing was very low and was inadequate to sustain imposed embankment load. This resulted in the failure of the embankment. Analysis of the tailing deposit revealed that even after failure, settlement was continuing due to imposed embankment load. Under normal onedimensional consolidation, the tailing deposit would have taken about 5.7 years for 90% of primary consolidation. However, in order to mitigate the scarcity of storage space, mining plan required raising the height of the embankment within next six to eight months. Therefore, despite the fact that there was a failure, it was necessary to continue the construction on the underlying weak stratum. The system was redesigned with installation of prefabricated vertical drains (PVDs) to accelerate the consolidation process thereby gaining the in-situ strength. Strength was additionally enhanced by installing geogrids in multiple layers. It stabilized the existing embankment and also ensured construction of additional height over and above the existing embankment.INTRODUCTIONBeneficiation plant in the Iron mines enhances the mineral content by separation of contaminants and fines. The residue (waste material) is called tailings/tailings depending upon the grain sizes. These tailings in a slurry form are generally disposed in a pond called as tailing pond/tailing pond. Height of embankment of such ponds is increased either by upstream or by downstream or by centrally raising methods in different phases as quantum of deposition in the pond increases with time."

Jan 1, 2015

Jan 1, 1993

By Anburaj C., Srinivas A.

Deep excavation with support system is required to construct various part of underground structures like shafts, stations and entry structures etc. These structures have to be constructed using permanent or temporary embedded retaining walls with support system. The selection of a suitable type of retaining wall will depend upon the geological condition present in the particular location, time, cost and available equipment etc. In Bangalore Metro Rail Project, secant pile wall is adopted as the temporary earth retaining system and depth of excavation is about 20 m. It is designed initially based on bottom up construction methodology with 3 level of struts and 3 level of anchors but at later stage due to time and other construction related issues, it is decided to change the configuration to 6 levels of strut. Generally, in deep excavations, all the underground structures should be designed and checked for the critical forces from both permanent stage and construction stages. Since, secant piles are used as temporary retaining wall, only construction stage analysis is carried out to get the governing forces and deformation. In construction stage analysis, soil layers are defined with boundary conditions and the surcharge during construction and surcharge from actual building near the secant pile are considered. This paper discusses the effect of change in the support system from anchors to struts and how these changes in the support system affect the behavior of secant pile and subsequently adjacent buildings present in the influence zone of the excavation. As a result, in changing from anchors to struts, the wall displacement, strut forces and ground movement on the adjacent ground and buildings increases. The increase in deflection, ground movements and strut forces occurs during backfilling sequence of the underground station excavation. During backfilling, struts has to be removed and this imparts higher magnitude in deflection, strut forces and ground movements.

Nov 1, 2022

By Adrian M. Keller

Borehole televiewers are downhole inspection devices available for high-resolution imaging of a borehole wall following rock coring. Borehole televiewers should be considered by geotechnical engineers and geologists as a supplemental way of investigating rock for deep foundations. The optical televiewer (OTV) produces a digital optical image and the acoustic televiewer (ATV) utilizes reflected acoustic waves to produce images of the borehole walls. These devices can be utilized to examine soft or fractured zones in the rock mass, solution features, open joints or other voids not observable from traditional rock coring techniques. These devices along with computer post-processing can determine the strike and dip of joints, bedding planes, shear surfaces, or other structural features, eliminating the need for expensive oriented cores or manned downhole logging. An acoustic televiewer was utilized in the Fall of 2008 during the investigation phase for the I-70 New Mississippi River Bridge (I-70 MRB) in St. Louis, Missouri. Voids and fractures in the upper portion of the rock were described by prior consultants. Further investigation of these features was necessary to evaluate deep foundation options to support the main towers. Ten borings were drilled from a barge in the river at the two main tower pier locations. An ATV was utilized in each of the ten borings to produce images of the rock mass in the borehole and allow further investigation of the voids. Voids interpreted as solution features were readily identified in the ATV logs in multiple borings and at similar elevations, suggesting connectivity. Measurements of the voids? width, location in the borehole and orientation allowed a more thorough understanding of the potential impact the solution features may have on the planned deep foundations. An extensive grouting program was eliminated based on the ATV results.

Jan 1, 2010

By Jerold Bishop, Grant Bearss, Aleksey Egorov

"When a shock wave is released in the bottom of a drill hole filled with wet concrete slurry, the result is called an electrohydrodynamic effect, or EHDE. The energy is carried through the fluid with minimal loss because the slurry is an incompressible medium. Repetitive discharges provide a series of energy pulses that compact the soil along the pile shaft and at its base. The process is analogous to repeated applications of low-energy blast densification or to dynamic compaction. In general, the process is not depth dependent. EHDE was identified in the 18th century by an American scientist who observed that a spark between two electrodes placed under water induced a burst of pressure. In 1957, two Russian engineers formulated a process and received a patent for a method of creating a pressure wave by transforming power from an electrical discharge to a mechanical impact. They derived more than 200 applications for technical and industrial processes.In the 1970s, civil engineers at the Engineering and Building Institute in St. Petersburg, Russia, began to look at EHDE to improve the capacity of drilled piles. Early experiments showed that electric discharges in a wet concrete slurry mix could create a pressure wave of up to 26 MPa (3700 psi). Later tests demonstrated that this pressure level could be created in a drilled pile hole. The researchers devised equipment and in the early 1990s began to study pulse technology as applied to drilled piles.This application was accepted into the Russian Federation Building Code in the 1990s. The code treats “regular” drilled piles with equivalent bearing area as having roughly half the capacity of a driven pile. However, the code considers drilled piles treated with the EHDE technique a direct “one for one” substitution for driven piles and allows higher values if the capacity is established by static load testing. Hundreds of projects have been completed in Russia using this technology to value engineer drilled pile projects. In several instances, the number of drilled piles installed was fewer than half of the number originally planned for due to the capacity increase that EHDE-treated piles provided.Drilled PilesIn drilled pile construction, the EHDE process creates a mechanical pressure wave that impacts the base and sidewall of a drilled pile shaft. Soft, poorly consolidated or loose soil is compacted by successive pulses of pressure created by electrical discharges. These mechanical impulses are made by inserting a discharge probe into the wet concrete slurry. A discharge across the tip of the probe creates the pulse that travels outward to the sidewall and base of the drilled pile through the incompressible medium of the slurry. The power pack ratings for equipment presently in use are 35 and 50 kJ (kilojoule).Each pressure wave strikes the soil, causing compaction and expanding the hole. Workers apply the pulses until the size of the hole stops increasing. They watch the slurry level during pulsing. When the level quits dropping, further soil compaction in the drill hole sidewalls and base is not possible. After the pulse process is complete, workers insert a rebar cage and the pile is finished.The process does not alter the soil mineralogy. The electrical discharge is internally grounded and does not arc to the sidewalls of the drill hole. Soil is not scorched or altered in any manner; it is only compacted by the pressure wave. This technique has been used in urban areas with no effect on electrical or electronic equipment."

Jan 1, 2009

By Nabil F. Ismael, Mohamed El Deeb

"The behavior of laterally loaded step tapered bored piles in calcareous sand was examined by field tests. Lateral load tests were carried out on straight and step tapered bored piles 5.3 m long embedded 5 m below ground level. All piles were installed by augering. The straight piles were 0.2 m, and 0.3 m in diameter. The step tapered piles have a diameter of 0.3 m along the upper 10%, 20%, and 40% segment, respectively, changing to 0.2 m for the lower section. Two piles were instrumented with strain gages to measure the bending strains. All tests were carried out to failure. The purpose being to examine the ultimate lateral capacity and the deflection at working loads. Test results indicate non linear response and substantial increase in lateral capacity and decrease of deflection for the step tapered piles compared with the 0.2 m diameter straight shaft piles. However, beyond a depth of 40% of the pile length, the strengthening of the pile section by enlargement of its diameter had little effect on the lateral capacity and the deflection of step tapered bored piles.IntroductionFor many structures on pile foundations the ultimate capacity under lateral loads is important and may be the controlling factor in foundation design. Examples include transmission tower foundations and fender piles at sea port facilities. Increasing loads on these structures has resulted in piles of large diameter and depth at a significantly higher cost.In this work, the use of step tapered bored piles with a larger diameter along the upper segment of the piles is examined by field testing and analysis on single piles in calcareous desert sands. Lateral load tests were carried out on straight and step tapered piles 5.3 m long embedded 5 m below ground level. The straight piles were 0.2 m, and 0.3 m in diameter. The step tapered piles had a diameter of 0.3 m along the upper 10%, 20%, and 40% segment, respectively, changing to 0.2 m for the lower section. Two piles were instrumented with strain gages to measure the bending strains. All tests were carried out to failure. The purpose being to examine the ultimate lateral capacity and the deflection at working loads for step tapered bored piles."

Jan 1, 2005

By H G. Poulos

"This paper sets out a simplified approach by which the practical foundation designer can undertake the relevant calculations to satisfy the requirements for deep foundation design in seismic areas. The following matters are dealt with:a. Design issues that should be addressed;b. Pile design for axial loading, including the possible effects of liquefaction;c. Pile design for lateral loading where liquefaction does not occur;d. Pile design for lateral loading where liquefaction does occur;e. Measures to mitigate against liquefaction effects.The paper is a modified version of a paper presented in 2013 to the 19th NZGS GeotechnicalSymposium, Queenstown, New Zealand.1. INTRODUCTIONConsideration of the effects of earthquakes and seismic loadings is an increasingly important aspect of modern foundation design, and most contemporary standards have a mandatory requirement for such consideration. For example, the Australian Piling Code, AS 2159-2009, states that “a pile shall be designed for adequate strength, stiffness and ductility under load combinations including earthquake design actions”. However, the methods by which such considerations can be undertaken are generally not set out in the standards, and many approaches have been utilized, ranging from very simplistic methods to extremely complex computer analyses. Accordingly, there appears to be scope for an approach that is soundly based but which is neither too simplistic nor too complex.Poulos (1989) has suggested that there are three categories of analysis and design, as follows:1. Category 1: empirical methods.2. Category 2: simplified but soundly-based methods.3. Category 3: more comprehensive methods that are soundly-based, and site-specific.The objective of this paper is to set out a systematic but simplified approach which falls into Category 2 above, and by which the foundation designer can undertake the relevant analyses to satisfy the foundation design requirements for seismic regions. Emphasis is placed on methods that do not require “black box” software or which employ complex soil models in which the physical meaning of the parameters is unclear."

Jan 1, 1900

By P. Kiruthika, A. Murali Krishna

Soil liquefaction is a dangerous phenomenon that involves huge damages during strong earthquake ground motion event. Stone columns (SCs) are widely used as liquefaction mitigation element which is expected to perform the improvements against liquefaction hazard by densifying, increasing the stiffness and rapid dissipation of excess pore water pressure in the surrounding soil. Although in the recent times few studies on the behaviour of stone columns in the seismic zone has evolved, the performance of SCs in the multi-layered soils is not extensively examined. This paper presents the numerical investigations on the performance of SCs installed in the multi-layered soils as a liquefaction mitigation measure against the seismic loading. The acceleration time histories, Excess Porewater Pressure (EPP), vertical displacement and stress ratio evaluated along different depths using PLAXIS 2D. With the installation of stone column there is a considerable reduction in the acceleration amplitude, which in turn reduces the EPP and vertical displacement at different locations and the amplitude of reduction depends on the soil stiffness levels at the depth.

Sep 1, 2022

By Laurel E. Blackman

The DFI Project Information Management Systems (PIMS) Committee cooperated with the US Army Corps of Engineers (USACE) to develop a specification for PIMS used on USACE projects. Once completed the Committee developed a more generic version of this specification for general use, which is contained in this document. This first edition has simply removed the USACE-related requirements from the document. The committee will continue to work on this specification to enhance the content and also incorporate recent technological development for these systems. It is the Committee's intention that a second edition will be issued in 2022.

Jan 1, 2021

By Danny Déry-Chamberland, Peter Bowman, Michael Byle

"The Barrage des Quinze dam is a concrete sluice dam consisting of 19 spillway sections, each of which is approximately 7.6 metres wide and 14.5 metres deep. Rehabilitation efforts being performed on the dam including demolition and improvement of the roadway and spillway sections and grouting to mitigate underseepage. Initially, conventional cement grouting was attempted and was successful in 14 of the spillway sections, but unsuccessful in 5 of the sections due to the high water flows which washed the grout away. The removal of the roadway and portions of the piers during construction temporarily reduced the stability of the structure limiting grouting pressures that could be applied. This and the substantial high water flows (leakage) beneath the dam between the concrete/rock contact and within fractures in the upper rock formation created a challenging situation to create a cutoff.A grouting solution was developed that involved implementing several different grouting methods and materials including balanced high mobility grouts (HMG); low mobility grouts (LMG); polyurethane grouts; and sodium silicates. Because of the critical scheduling for the work, multiple approaches were planned and made available on site so that the work could proceed with the best technology with little, if any, time loss. The end goal of the grouting program was to create a seepage cutoff beneath the 5 sections of the dam in a stepwise process. The initial step was to fill the large openings and create a grout barrier to reduce the high water flow. The second step was to seal the contact between the base of the dam and the bedrock; and the third step was to complete closure by grouting a deep grout curtain into the underlying rock. Other features of the work included an extensive grout mix testing program, water pressure testing, borehole camera survey, and monitoring of the grout injections."

Jan 1, 2016

By Seth H. Hamblin, Leo J. Hart, John E. Regan

The Route 6 /10 10 Interchange Design/Build project, located in Providence, Rhode Island, involves the design and construction of five (5) new elevated bridge structures to replace and reconfigure the existing interchange and to provide a link between Route 10 northbound and Route 6 westbound. Due to site logistics, headroom restrictions, and depth to bedrock, 50 ton drilled micropiles installed in the deep medium dense sand strata were initially proposed as the deep foundation solution. Post project award, Geosciences Testing and Research, Inc. (GTR) performed various analyses and developed an alternate driven pile solution using steel Tapertube. The results of these analyses indicated that driven steel taper tube and steel pipe piles could develop greater capacities than the drilled micropiles in the granular soil layer, thereby reducing the number of foundation elements, decreasing construction schedule and providing a more cost effective foundation alternative. A comprehensive driven pile load test program was subsequently executed by GTR and the Design Build Team led by Barletta Heavy Division of Canton, Massachusetts, to assess the performance of Tapertube and steel pipe piles, including pile drivability, load-deformation characteristics under static and dynamic loading, and to develop site-specific design parameters in two (2) distinct test areas. The test pile program included dynamic, static compression, tension and lateral load tests on each test pile. Load test measurements were automated with embedded Vibrating Wire Strain Gages (VWSG) to measure load transfer with depth. The execution and results of the successful pile load test program are presented and offer unique case study and valuable data for the use of Tapertube piles on deep foundation projects in the New England region INTRODUCTION The Rhode Island Department of Transportation (RIDOT) Route 6 / Route 10 Interchange is located west of downtown Providence. Originally constructed in the 1950’s as a highway bypass around the historic Olneyville neighborhood, the interchange consists of a series of nine (9) bridges and ramps that serve as a vital east-west link between Interstate 295, 95 and 195. Based on recent bridge rating assessments, seven of the nine bridge structures are rated “structurally deficient”. With many bridge structures shored with temporary supports as many as 15 years ago, the interchange is in critical need of replacement. In 2018, RIDOT awarded the Route 6/10 Reconstruction Design-Build Project to 6/10 Constructors, Joint Venture. Led by Barletta Heavy Division of Canton, Massachusetts, the Design Build team includes O&G Industries, DW White Construction, Aetna Bridge Co. and AECOM. The scope of work includes the replacement of the bridges and ramps, and will provide direct access from Route 10 northbound to Route 6 westbound. Valued at over $400M (US), this is currently the largest project awarded in RIDOT history.

Jan 1, 2019

The intent of this manual is to provide guidelines for inspectors of drilled shaft construction otherwise referred to as drilled piers, caissons or bored piles. It should also be helpful to train beginning geotechnical engineers with limited first hand experience or for geotechnical engineers who are training inspectors. It is expected that the general guidelines and procedures described here will be supplemented by local geotechnical engineers working in a particular region based on local practice and experience. Since drilled shaft construction procedures vary widely based on local geology and size of project, an all-inclusive manual is not considered practical. This manual focuses on traditional topside inspection for routine drilled shaft construction. Other inspection and evaluation methods that rely on electronic equipment are available, but these methods require extensive training and experience in the interpretation of results. These more sophisticated methods of drilled shaft inspection and evaluation are common in construction, but they are usually provided by specialty subconsultants. The subconsultant will typically submit a report for each shaft, which will be reviewed by the geotechnical engineer. Other manuals are available to describe the electronic methods of drilled shaft inspection.

Jan 1, 2004