Search Documents

By Shoji Higashi, Nobuhiro Honda, Takeo Asanuma, Tatsuo Nagatsu, Masaki Kitazume, Sachihiko Tokunaga, Shigeru Kubo, Hidenori Takahashi, Tsuneyasu Onishi, Yoshiyuki Morikawa

"Various kinds of civil engineering structures and facilities were seriously damaged in the earthquake in Tohoku and Kanto regions of Japan on 11 March 2011 due to the greatness of its magnitude. In contrast, many structures resisted the large seismic force having been reinforced by the CDM (Cement Deep Mixing) method, which is often used for increasing the bearing capacity of ground and improving seismic performance. This paper summarizes the field survey undertaken to investigate damage to structures and facilities reinforced by the CDM method. Several prefectures and metropolitan areas were selected for the survey, based on the occurrence of strong seismic motions. A total of 847 structures and facilities were studied, in the survey using a questionnaire, which mainly inquired about the appearance of structures and facilities. Of the respondents to the questionnaire, 789 replied that there were no seriously damaged structures. The paper presents the damaged and non-damaged sites of CDM-technique sites and non-CDM-techniques sites. It can be concluded from the field survey that the CDM Method demonstrates high efficacy and durability against a strong seismic motions.INTRODUCTIONDuring the afternoon of 11 March, 2011, a huge magnitude-9.0 Mw (Category 9.0 on the Richter scale) earthquake occurred about 25 kilometers below the Pacific Ocean’s surface off the coast of Tohoku. This massive earthquake, now called the 2011 Off the Pacific Coast of Tohoku Earthquake was the largest earthquake ever observed in Japan. The seismic intensity of this earthquake was measured 7, the maximum on the Japanese intensity scale, as observed 7 in northern Miyagi Prefecture. The earthquake caused severe damage over a wide area from Tohoku to Kanto, and triggered large tsunamis that struck the Pacific coast of Hokkaido, Tohoku, and Kanto. The number of missing and fatalities caused by this earthquake exceeded 18,000 persons, making this an unparalleled earthquake disaster with a cost-in-life toll not experienced by Japan in recent years. Because of the scale of its seismic motions, the earthquake damaged facilities and structures of many kinds. In the years prior to this earthquake, the CDM method was used extensively to increase the bearing capacity of the ground as an anti-seismic countermeasure and to prevent liquefaction. Immediately after the earthquake, the CDM Association visually surveyed the state of damage to about 800 facilities in the Tohoku and Kanto regions where a seismic intensity of 5 or higher was observed. This report summarizes the survey of damage to facilities and structures constructed applying the CDM method in order to confirm the durability and performance of the method against seismic motions."

Jan 1, 2015

By Y. M. Ha, T. D. Nguyen, D. T. Nguyen, H. K. Choi

Conventionally, cement deep mixing (CDM) columns are designed to have constant diameters over the improved depth as this facilitates the construction procedures. However, this design pattern may be inefficient in cases of spread footings or shallow foundations. This paper first briefly introduces principles of an improved CDM method that can create head-enlarged CDM (termed PF) columns. A simple analysis approach was introduced to obtain optimal shape of PF columns that results in minimum settlement. The effectiveness of this improved method over the conventional CDM method was then illustrated by settlement analysis for an actual footing in a case study using two recommended analytical methods in the literature. Analysis results from the case indicated that by using the same amount of soil-cement mixed volumes, settlement from a footing on PF columns can reduce up to 10 % compared with that from the same footing on CDM columns. In addition, a material quantity comparison for the case indicated that to have the same settlement values the volume of each PF column can be reduced of around 10% compared with that of the CDM column. INTRODUCTION The cement deep mixing (CDM) method is one of the most popular methods in ground improvement works. Details on the method such as construction procedures, necessary equipment and recommendations are described in many references or manuals (e.g. Bruce et al. 2013, BS EN 2015, Kitazume and Terashi 2013). Conventionally, CDM columns are designed to have constant diameters over the improved depth as this facilitates the construction procedures. However, this design pattern is found inefficient in cases of spread footings or shallow foundations as the upper soil layers are naturally weaker than the deeper ones but are subjected to larger amount of induced stress from the superstructures.

Jan 1, 2019

By E. Naesgaard, Brian E. Hall, A. Amini, Advanced Geosolutions, A. Azizian

"A 2 km section of the Evergreen Line Rapid Transit Project is supported on improved ground consisting of cement deep soil mix (CDSM) panels because of highly variable and challenging soil conditions, especially the potential for seismic liquefaction-induced lateral spreading. CDSM was used as an alternative approach in place of driven piles for reducing the seismic lateral spreading displacements. An additional significant aspect of obtaining owner acceptance for CDSM was demonstrating that both seismic and non-seismic performance would equal or exceed that of using driven piles. It was recognized that, to demonstrate adherence to the seismic performance requirements, seismic design should be based on dynamic analyses (using FLAC) to estimate likely displacements and stresses/strains in the CDSM panels. One focus of the analyses was investigating the potential for cracking of the CDSM panels and the resulting displacements. This was simulated using the Ubiquitous-Joint and UBCSAND constitutive models.INTRODUCTIONThe Evergreen Line Rapid Transit Project (ELRT) is an 11 km extension of the SkyTrain system through Burnaby, Coquitlam and Port Moody in the Lower Mainland of British Columbia, Canada (Figure 1). The ELRT project is being delivered through a Design/Build/Finance model by Evergreen Rapid Transit Construction (EGRT), an SNC-Lavalin Inc. company, to the Province of British Columbia (the Province).This paper discusses the ground improvement design for a 2 km section of the alignment through Port Moody, a historic city at the head of Burrard Inlet. The alignment is located in a right-of-way of restricted width with many pinch points close to residential and commercial properties, and directly adjacent to the Canadian Pacific Railway (CPR) mainline tracks. The ground slopes from south to north across the alignment towards Burrard Inlet at inclinations of up to about 6%. Design and construction of the Port Moody section was subcontracted to SNC-Lavalin Constructors (Western) Inc. (SLCW) and SNCLavalin/ Graham Construction Joint Venture (SGJV). Construction included single- and double-track slab guideways, pocket track (where up to four to six tracks were present), and Moody Centre Station."

Jan 1, 2015

By Abolfazl Eslami, Samieh Rezazadeh

"Semi-Deep skirted foundations are considered to be a viable option for a variety of onshore and offshore applications. It is necessary to determine appropriate foundation configurations that allow loads to be transferred safely to the surrounding soil. For this purpose the bearing capacity and stability analyses subjected to combined vertical, horizontal and moment loadings must be found. In this paper the vertical undrained bearing capacity is estimated via finite element analyses. The circular skirted foundations with different geometries considering embedment depth (embedment ratio between 0-2) and size effects (diameter equals to 5, 10, and 20) have been studied. Stress field, kinematic mechanism accompanying failure and bearing capacity factors for total, end and shaft resistance in semi-deep foundations with various embedment ratios are investigated. Furthermore, two probable mechanisms i.e. internal flow and soil plug for estimating foundation capacity for design purpose in practice have been assessed. Comparisons with different research works including conventional methods, upper and lower bound approaches, and finite element analyses have indicated that the conventional methods underestimate the bearing capacity due to ignoring the significant role of shaft resistance. Determining appropriate economic foundation configurations to transfer loads safely to the surrounding soil is a major issue in geotechnical engineering. Shape and dimension of foundations, embedment depth, soil characteristics and applied loading, all affect the foundation performance. Recent studies have shown that for foundations with large breadth and of D/B between 1 to 4, kinematic mechanisms and failure modes are different from the two main types of foundation (i.e. shallow and deep). Therefore, D/B factor must not be considered as the only factor for defining foundation type. ""Semi-Deep foundations"" are another foundation category distinguished based on their performance. This relatively new concept is becoming increasingly an optimum alternative for shallow and deep foundations to support structures especially in accessible depth. As illustrated in ""Fig. 1"", different types of semi-deep foundations consist of:"

Jan 1, 2017

By Tanaya Deb, Sujit Kumar Pal

"Experimental investigations are carried out on failure pattern around 2D models of belled anchor piles in dry sand bed of density 15.60 kN/m3 under uplift. The models are having thickness ratio (Ts/Tb) = 0.28, 0.32, 0.38 and 0.46 and total 12 numbers tests are performed on models possessing 45° bell angle and shaft thickness 26 mm. The foundation bed is prepared with alternate dyed and non-dyed sand layers and continued upto reaching embedment ratio of 3, 4 and 5 for each width ratio. The failure points are presented with respect to meridian section of anchor in X-Y coordinate system and the equations formed are of polynomial of degree 3; and R2 values are near about 1. The developed wedge is implemented as three-dimensional axisymmetrical failure surface around similar 3D models. In the horizontal slice method vertical limit equilibrium is used for calculating weight of wedge and mobilized shear (as per Chattopadhyay and Pise, 1986) on the slip surface of each element. The summation of all elementary forces demonstrates gross uplift capacity. The initial and final failure angles are detected and parametric study is conducted on failure pattern as well as predicted net ultimate uplift capacity. Almost all the analytical data are within ± 10% variations with respect to the experimental results of uplift capacity which shows better correlations. INTRODUCTION Belled or enlarged base anchor piles are attractive and economic alternative to the geotechnical engineers for compressive load bearing capacity as well as tension anchorage. These types of anchors may be useful for foundations erected below ground water table. In light weight structures like radar tower, television tower, power pole and outdoor sign pools imbalance horizontal forces due to wind loads, are more than of those self-weight of those structures. Due to chronic tensile loads most possibly from wind loads and associated imbalanced cable tension, the legs of power transmission tower should be properly designed to be safe against resultant pull-out forces. In belled anchor pile, uplift is influenced by embedment ratio, diameter ratio; so, contributions of these parameters on failure surface influence uplift capacity. Balla (1961) first introduced non-linear failure surface in the pattern of circular arc based on Kotter’s equation (1903) and soil friction was assumed to act on slip surface. The predictive mathematical models established by Matsuo (1967), Rao and Kumar (1987), Chattopadhyay and Pise (1986), Saeedy (1987) and Ghaly and Hanna (1994); it was reported that net ultimate uplift capacity was combination of bulk weight of failure wedge and shear resistance along slip surface acting in opposite direction of wedge movement. From the literatures available till date, it reveals that the contribution of mobilised shear and weight of breakout wedge separately, demanding for more clarification depending on the on parameters like embedment ratio, diameter ratio."

Jan 1, 2015

By Abhirami B., V. Balakumar

Piled raft foundation system is an intelligent geotechnical concept, developed towards reducing the settlement of the raft and the footings by providing pile elements below the raft or footings, as the case maybe. Although a large volume of works has been done on the behaviour of piled rafts by observational studies, the effect of construction methodologies such as deep excavations, the installation methodologies used for piling etc appear to have not been covered adequately. This paper discusses the effect of deep excavations, pile installation techniques and the effect of adding structural elements, based on the data available from published literatures. Based on this study, the performance of the piled raft monitored by the author has been revisited and the results of such a study are discussed.

Nov 1, 2022

By Jin-Wei Huang, Bradley J. Fleming, Sri Sritharan

"Although soil improvement and its application to deep foundations is gaining popularity in the engineering community, this technique is not widely used in high seismic regions due to lack of fundamental understanding of both the behavior of improved soils under high-strain cyclic loading and the interactions between the pile, improved soil, and unimproved soil. This paper describes part of an ongoing Network for Earthquake Engineering Simulation (NEES) project, where two identical full-scale steel pipe piles were driven at a soft clay site in Oklahoma. The soil surrounding one of these piles was improved using the cement deep soil mixing technique in order to enhance its lateral load behavior. Both piles were tested for seismic resistance using dynamic and quasi-static loading.The pile in unimproved soil provided larger displacements with limited lateral force resistance. This pile was subjected to lateral displacements of up to 400 mm, but experienced minimum inelastic actions. On the other hand, the pile in improved soil reached its lateral capacity at a displacement of 100 mm, at which point the critical region at the base of the pile just above the improved ground experienced buckling and fractured due to low cycle fatigue. Compared to the pile in unimproved soil, the improved ground increased the system strength by 42%. Although the soil was improved over 2900 mm, the effective improvement depth was approximately 1300 mm below the ground surface.In this paper, it is demonstrated that the effects of block type soil improvement of limited horizontal and vertical dimensions can be described using a simplified theoretical approach involving a modification to the well-known p-y representation of soil response. An example using this method is presented and shown to give adequate support to a standard 12-inch diameter steel pipe pile embedded in soft soil,IntroductionPilings are the preferred foundation support for many civil engineering structures including highway bridges, railroad bridges, and port wharves. These structures and their foundations are subjected to forces created by earthquakes, wind, waves, water current, vessel impact, ice, and gravity. All loads applied to the superstructure must be transmitted to the foundation where they are resisted by the surrounding soil. With significant lateral loads, use of pile foundations may be the only solution to transmit large structural loads to competent soils. Piles supported by competent soils are relatively easy to design and costs are often attainable. However, thick layers of weak soils such as soft clays are widespread in high seismic areas (e.g., San Francisco, southern Nevada, Washington, Eastern Missouri, and Arkansas), exacerbating design challenges. Soft clays reduce the lateral resistance of the pile-soil system, making the pile foundation less cost effective. In this case, the current design practice is to use an increased number of larger diameter piles, which is a costly alternative (see SDC, Caltrans 2010). An innovative and more cost-efficient solution to this problem is to improve the soil within a short depth surrounding the foundation, thereby increasing its lateral stiffness. Some well-known methods for improving soil include deep soil mixing, stone columns, and simple soft soil replacement with select granular material."

Jan 1, 2017

By Bradley J. Fleming

Although soil improvement and its application to deep foundations is gaining popularity in the engineering community, this technique is not widely used in high seismic regions due to lack of fundamental understanding of both the behavior of improved soils under high-strain cyclic loading and the interactions between the pile, improved soil, and unimproved soil. This paper describes part of an ongoing Network for Earthquake Engineering Simulation (NEES) project, where two identical full-scale steel pipe piles were driven at a soft clay site in Oklahoma. The soil surrounding one of these piles was improved using the cement deep soil mixing technique in order to enhance its lateral load behavior. Both piles were tested for seismic resistance using dynamic and quasi-static loading. The pile in unimproved soil provided larger displacements with limited lateral force resistance. This pile was subjected to lateral displacements of up to 400 mm, but experienced minimum inelastic actions. On the other hand, the pile in improved soil reached its lateral capacity at a displacement of 100 mm, at which point the critical region at the base of the pile just above the improved ground experienced buckling and fractured due to low cycle fatigue. Compared to the pile in unimproved soil, the improved ground increased the system strength by 42%. Although the soil was improved over 2900 mm, the effective improvement depth was approximately 1300 mm below the ground surface. In this paper, it is demonstrated that the effects of block type soil improvement of limited horizontal and vertical dimensions can be described using a simplified theoretical approach involving a modification to the well-known p-y representation of soil response. An example using this method is presented and shown to give adequate support to a standard 12-inch diameter steel pipe pile embedded in soft soil.

By Thomas L. Vande Voort

The strategic plan for bridge engineering issued by AASHTO in 2005 identified extending the service life and optimizing structural systems of bridges in the United States as two grand challenges in bridge engineering, with the objective of producing safer bridges that have a minimum service life of 75 years and reduced maintenance cost. Material deterioration was identified as one of the primary challenges to achieving the objective of extended life. In substructural applications (e.g., deep foundations), construction materials such as timber, steel, and concrete are subjected to deterioration due to environmental impacts. Using innovative and new materials for foundation applications makes the AASHTO objective of 75 years service life achievable. Ultra High Performance Concrete (UHPC) with compressive strength of 26,000 psi (180 MPa) and excellent durability has been used in superstructural applications but not in geotechnical and substructural applications. This paper explores the possibility of using precast, prestressed UHPC piles in future bridges. An H-shaped UHPC section, which is 10-in. (250-mm) deep with weight similar to that of an HP10×57 steel pile, was designed for constructability and economical reasons. Instrumented UHPC elements were cast to conduct large-scale field tests. In the field, two UHPC piles have been successfully driven in glacial till clay soil and load tested vertically. Test results, durability, drivability, and other material advantages over normal concrete and steel indicate that UHPC piles are a viable alternative to extend the life of bridge structures.

Jan 1, 2008

By William (Bill) H. Walton

"I arrived in Chicago in 1993 with Dr. Ralph Peck’s University of Illinois bulletin titled Engineering Properties of Chicago Subsoils (Bulletin 429), which he published in 1954 with William Reed. Being an outsider, I wanted to learn from Chicago geotechnical practice leaders that included Clyde Baker, Jr., John Gnaedinger, Charles Pfingsten, Dr. Safdar Gill, Robert Lukas and Dr. Jorj Osterberg, who have influenced foundation designs for the structures that make up the contemporary Chicago skyline. One of my immediate goals was to get the Illinois Structural Engineering license to be on par with the likes of Eli Cohen, Mike Tylk, Stan Korista, Bob Halverson, Joe Burns, Ron Johnson, Bill Baker, Bob Sinn, Chuck Anderson and Dave Eckmann, who have led their structural firms in the design of the skeletal core and frames of many of Chicago’s iconic buildings (and for many other buildings around the world). From my time with GEI Consultants (GEI), then on with STS Consultants (STS, and now AECOM), and now back with GEI, I have had the opportunity to analyze and design foundations and, with the help of many skilled foundations and building constructors, to verify that predicted foundation performance matches actual movement data. The theme of Chicago’s foundation design practice is to assume and verify. In 1948, Peck published the History of Building Foundations in Chicago (Bulletin 373) that was updated in 1998 by Baker, Pfingsten and Gnaedinger, who meticulously documented hundreds of Chicago’s foundations, and have shown the value of advanced analyses and testing to advance the deep foundation design practice that includes a variety of high-capacity driven and drilled deep foundations. Mehmet Uyanik, Peck and Baker have made Chicago’s subsurface into a full-scale foundation test laboratory. They confirmed soil mechanics principles like Terzaghi’s 1-D consolidation theory when early foundations bearing on sand-clay crust over soft to medium silty clays (e.g., Auditorium, Masonic Temple, Monadnock Block and Old Board of Trade buildings) took 40 to 60 years to consolidate clay 1 to 2 ft (0.3 to 0.6 m). They also confirmed proven increases in bearing pressures based on measured performance of deep foundations bearing on the glacially derived hardpan clay till and in solid dolomite that underlies Chicago."

Jan 1, 2017

By Peter Iovino

Unfortunately, I don't know the unit cost per cubic yard of treatment. I reflected on that yesterday and I don't think that we considered the use of micropiles. They could have been an option. The challenge may have been picking up some of the lateral load but I think the micropiles could have been installed on a batter and perhaps extended to rock. We could have considered them, but I do not believe we explored micropiles as an option for this project.

Feb 10, 2003

By D. J. Ketkar

It is a frequent experience to find that the Sub-surface Investigation (S.I.) data is either inadequate or misleading. However, such cases are rarely reported. Nonetheless, the projects suffer on-account of delays, cost-over-runs, disputes and/or compromise of the safety norms. Many times S.I. is considered unnecessary or is carried out as a ritual, mainly due to (i) non-availability of good S.I. agencies, or (ii) absence of Geotechnical consultant, or (iii) shortage of time. Importance of S.I. cannot be over emphasised. Yet the profession is in a state of confusion - mainly because of lack of competent professional agencies and of well-defined roles/responsibilities of the concerned parties. In this paper, some suggestions are made to get better returns from the S.I. activity.

Jan 1, 1996

By Mohamed Elgouhary, Carol L. Tasillo, Daniel Koziol

"The Bolivar Dam, located near the Village of Bolivar, Ohio is one of a system of dams designed to provide flood control and water conservation in the Muskingum Watershed. The Bolivar Dam is a “dry dam” that only impounds water during flood events. In order to address problematic seepage, which negatively affects the structural stability of the dam, the U.S. Army Corps of Engineers (USACE) designed a partial-depth and partial-length Seepage Barrier Wall (SBW) through the upstream slope of the dam. For this project, TREVIICOS constructed a 36 in (914 mm) positive SBW by plastic concrete panel wall method and excavated using hydromill and clamshell equipment. The plastic concrete was manufactured on-site, which allowed for enhanced quality control and prompt service. This required the installation, commissioning and operation of a concrete batch plant on-site. This paper presents the challenging aspects of the design, manufacture and placement of the plastic concrete for the SBW in order to meet contract strength and permeability requirements as well as workability requirements necessary for tremie concrete placement.Project General InformationBolivar Dam is located in Northeast Ohio (Fig. 1). It is one of a system of sixteen dam projects designed to provide flood control and water conservation in the Muskingum Basin, which covers 20 percent of the State of Ohio (Fig. 2). Bolivar Dam is on Sandy Creek, a tributary of the Tuscarawas River.The Dam has been constructed, operated and maintained by the USACE, for the Muskingum Watershed Conservancy District. Its construction was completed in 1937 and it has been in operation for flood control since 1939.Bolivar Dam is a rolled earth fill dam, with a typical embankment section made of a central impervious core flanked upstream and downstream by a pervious outer shell with downstream rock toe. The embankment has a maximum height of 87 ft (26.5 m) and a crest length of 6,300 ft (1,920 m), and is comprised of the main embankment starting on the left abutment of about 1,500 ft (457 m) heading to the Northeast, followed by the terrace embankment of 4,800 ft (1,463 m) heading to the North. An upstream impervious blanket extends up to 500 ft (152 m) upstream of the dam along the majority of its length. The outlet works are to the left of the embankment, and consist of an intake structure with six gates, followed by two outlet conduits that finish in a stilling basin. To the left of the outlet works is the uncontrolled emergency spillway, which was doubled in width to 540 ft (165 m) in 1989, and excavated material utilized for construction of a stability berm against the upstream face of the main embankment. A concrete parapet wall was also installed along the upstream side of the crest during this work. In 1982, a toe drain, downstream filter berm and line of 35 relief wells were installed. The filter berm was recently extended an additional 200 ft (61.0 m) downstream and granular filters were placed over an approximate 2000 linear ft (610 m) reach of the lower terrace slope. (Fig. 3)."

Jan 1, 2016

By Qingwei Joshua Ong

Tension piles, also known as uplift or anchor piles, are necessary to resist uplift forces that might cause structural distress. In excavation projects, most uplift forces are developed because of hydrostatic pressures, and so tension piles are subjected to a great deal of tensile forces. Most current methods of design for tension piles completely neglect the tensile strength contribution of concrete, relying only on the steel members to carry the tensile stresses, resulting in an overly conservative design. The stressstrain behavior of the composite material of concrete and steel must be considered for a realistic simulation of tension piles. This paper will examine a case on a tension bored pile in typical soft clay to demonstrate the importance of considering the tension strength and tension softening of the concrete.

Nov 1, 2022

By Matthew Janes

The new Bow office complex will become the new headquarters of EnCana Corporation, a leading Canadian oil and gas company. The shoring system, encompassing nearly two city blocks and excavated to a depth of 20.5 m, supported surrounding utilities and buildings in downtown Calgary. Past excavations in the area experienced large amounts of rock movement, the mechanics of which were poorly understood. The focus of this paper is the design process and construction results concerning rock movement and the effectiveness of the shoring structure. A lack of information regarding the local in-situ stresses and shear band propagation in the bedrock led to research of case studies in the Calgary area and a peer review from local experts. Several geotechnical scenarios were analyzed using FLAC to account for varying residual rock stresses and the location and composition of weak rock layers suspected of causing shear band movement. Movement characteristics were predicted that would identify the rock deformation mechanic throughout the construction process. A detailed monitoring programme composed of precision monitoring targets, inclinometers, and extensometers was established to provide accuracy and redundancy in establishing the movement of the rock and excavation support structure. The results of the programme were used to identify the rock deformation mechanics and further refine the FLAC analysis. To date, monitoring indicates that localized shear band effect is the leading cause of rock movement. The phenomenon appears to be directionally dependent and strongly correlated to excavation extent.

Jan 1, 2008

By Les R. Chernauskas

? What is Integrity Testing? ? Cross-Hole Sonic Logging (CSL) ? Single-Hole Sonic Logging (SSL) ? Typical Specifications ? Case Histories ? Observations and Conclusions WHAT IS INTEGRITY TESTING? General Definition ? Process in which the condition or structural makeup of an object can be evaluated with respect to defects such as a reduction in cross section (void or crack) or reduction in material strength (water, slurry, soil mixed with concrete). ? If the defect is severe enough, it can reduce or alter the load carrying ability of the object.

Jan 1, 2001

By Jerold Bishop

The application of the ?electro-hydrodynamic effect? (EHDE) to civil engineering has been made in the construction of drilled piles. Equipment for the commercial application of this process was developed in Russia in the late 1980's. The process is approved for general use by the Russian Federation building code and numerous projects have been successfully completed with this technique. EHDE is a process by which a moderately powerful shockwave is released in the bottom of a drill hole filled wet concrete slurry. The energy is carried outward through the fluid with minimal loss because it is an incompressible medium. Repetitive discharges provides a series of energy pulses which will compact the soil along the pile shaft and at base of the pile. The process is analogous to repeated applications of low energy blast densification or to dynamic compaction. In general, the process is not depth dependent. Repeated application of this treatment in a drilled pile hole can increase soil density at the base and along the shaft of the pile, as desired. The overall result is that the geotechnical capacity can be improved significantly. Test results documenting improvements are presented and other applications considered.

Jan 1, 2007

By Karen Talbot, Noah Maier, Rob Jameson, Giuseppe Gaspari

A storage and drainage tunnel advancing below I-75 in Detroit, Michigan experienced sudden subsidence. The Tunnel Boring Machine (TBM) was damaged to the extent that its shield, cutting head and extensive interior components needed to be extracted and replaced along with several completed tunnel segments. The tunnel was 16 feet (4.9m) in diameter with crown over 79 feet (24m) deep at the time. The tunneling contractor immediately engaged their designers and specialty subcontractors to develop a scheme to access the machine and repair the tunnel. They required a shaft 99 feet (30m) deep, with unobstructed plan dimension of 50 feet (15m) to accommodate the large components that needed to be removed and replaced. This precluded the application of an internally braced excavation and instead earth support solutions focused on use of a compression ring. Since the completed tunnel section behind the TBM obstructed closure of the compression ring below its invert, this paper describes the innovative access shaft solution employed. A conventional compression ring was constructed using 5 feet (1.5m) diameter drilled shafts down to the tunnel crown. In front of, and to the sides of the tunnel heading, the secant shafts were extended to over 150 feet (46m) depth, creating a horseshoe of support extending 50 feet (15m) below the planned excavation invert. Larger diameter "King Pile" shafts were drilled immediately to either side of the tunnel, overlapped into each end of the secant "horseshoe". The king pile shafts, together with a heavily reinforced ring beam above the crown elevation, acted as a door frame to transfer hoop loads from the incomplete secant arc into reaction supports above and below the tunnel. These oversize king pile shafts were extended and socketed into rock over 70 feet (21m) below tunnel invert. Very tight installation tolerances were necessary to maintain secant shaft alignment to depths exceeding 150 feet (46m). The project operational, geotechnical, and quality data was managed and visualized using a custom GIS interface. This paper will present the design approach employed and review the construction and quality program selected to repair the tunnel.

Oct 1, 2022

By Sastry Putcha, Santosh Mummaneni, Swamy Avasarala, Vamshi Vemula

"This paper presents the results from a case study on the comparison of two strain acquisition instrumentation technologies, Geokon rebar strainmeters and Embedded Data Collectors (EDC) for the DC Water Main Pump Station project, in Washington D.C. These two instrumentation systems were installed by AVER in a single 18-inch (0.45 m) diameter augercast pile (with one-1.25 inch (3.175 cm) dywidag bar) at critical locations to determine the load transfer mechanism and establish a comparison between strain/load measured with these two systems along the pile. A quick static load test was performed on the test pile as per ASTM D1143 standard.Prior to the installation of the pile, a 24-inch (0.6 m) diameter outer casing was installed to the proposed cutoff elevation of -22.5 feet (-6.85 m) to discount the frictional resitance within the upper overburden zone. The pile was then drilled through the outer casing to the tip elevation of -65.02 feet (-19.8 m) with inner casing within the overburden zone. Strainmeters along with EDC were installed on dywidag bar at various locations and then wet set into the concrete following auger retrieval. The loads measured with EDC and Geokon sensors were within 15% percent of each other.PROJECT BACKGROUNDProject Background & Requirements:Like any other foundation piles, augercast piles are extensively used in the public and private sector structures in the United States for many years. It is a common practice to perform static compression (ASTM D1143), tension (ASTM D3689), and lateral load tests (ASTM D3966) depending on the project requirements. In recent years, embedded strain sensors, manufactured by Smart Structures, USA has gained prominence for its use to collect both static and dynamic measurements for driven piles. In addition, AVER has successfully used EDC for collecting long term static measurements for an abutment drilled shafts for I-95 Hotlanes project in Virginia, USA.Geokon sisterbar strain gages are widely used in the foundation industry to monitor the load transfer mechanism within pile foundations throughout the world. As the Geokon strainmeters are vibrating wire and are welded to a sister bar, there is often a debate within the engineering community with regards to what modulus to use when converting measured strains to loads. EDC sensors, unlike Geokon strain gages are embedded directly into the concrete and therefore do not have the same concern."

Jan 1, 1900

By Cassandra A. Wetzel

"Rock socketed mini-piles are a desirable foundation alternative when design capacity is more than 40 tons and there is limited access. In this case history mini-piles were designed to support between 75 and 200 kips at 12 locations adjacent to a perimeter wall, a party wall and at cast iron column piers. Limited geotechnical information, low overhead clearance, and active building population tested the creativity of the team to get the piles installed. The key geotechnical concern during installation of the mini-piles was the presence of a glacial till layer above the bedrock surface that restricted the seating of the casing into bedrock with a track mounted drill rig. Soil loss during the advancement of the rock socket using an air hammer was excessive and increased the risk of subsidence. Over a three week period the engineer worked with the contractor to modify the design, means, methods, and materials to install piles with adequate load capacity. This paper will present the changes in design and construction methods that were required.INTRODUCTIONRock-socketed mini-piles are a common and desirable deep foundation alternative to support loads more than 40 tons in New York City. Limited vertical clearance, accessibility, vibration control, and load capacity make this pile type attractive; it also does not require a static axial load test when socketed into rock. This added benefit makes this alternative all the more feasible.The installation of a drilled pipe extending to bedrock through a glacial till deposit presented challenges to the contractor and engineers to confirm the casing is seated sufficiently into the rock prior to drilling the rock socket. The loss of soil between the steel pipe and the till/bedrock interface can compromise the performance of the pile and soil loss can result in settlement of the ground surface.This paper presents the design and construction method changes made on one project during the installation of ten limited access rock socketed mini-piles."

Jan 1, 2017