Search Documents

By Nuno Cruz, Saúl Rodríguez

"When executing offshore bored piles there are several specific factors and problems to consider in order to guarantee excavation stability. One of the methods employed to carry out this type of work consists in setting up a floating work platform, typically a barge, and implementing a soil stabilization system that combines a partial steel guiding casing with third generation polymeric drilling fluids. The main aspects to take into consideration when performing offshore pile boring works are soil stabilization, project design, work methodology and operational aspects. An example of a work methodology problem arises before any pile boring work takes place as the steel guiding casing contains water, sometimes salt water. What to do with this water in order to replace it by an adequate polymer fluid will determine the stabilization capacity as soon as the shaft advances below the protection of the casing. Another example of operational problem may derive from barge movements while executing boring activities. This study is the result of extensive field data collection and concrete logging analysis from marine projects using polymers in different continents. The bored pile stability target was set ranging between 2% to 15% of concrete overbreak. Values above 15% or below 2% mean that there is a stability problem. Then the off-target pile’s data is collected, analyzed and classified under categories. Thus, a direct correlation is established between the problem category and the final results. Modifying steps in the pre-established construction methods or operational variables guarantees target results without the need to replace the approved construction methods. As a general conclusion, the worldwide experience in large diameter marine works, allows to provide truthful information and solutions for these problems. In knowing how to follow a logical sequence of work and applying adequate work methodology will be the key for success.GENERALBackgroundTo carry out the drilling process of offshore bored piles there are two main options to take into consideration: drilling the pile by using full guiding casing until final depth; or using a combined system of partial steel guiding casing and support drilling fluids.The knowledge and situations described in this paper come from the experience acquired in different projects where the second method was employed. This construction method consists in installing a steel guiding casing by vibration and thus covering the water table and further stabilizing the soil below it with polymeric fluids until reaching the pile’s final depth. The Fig. 1 schematic shows an example of this method where H corresponds to the length of the steel guiding casing whereas the remainder of the shaft’s length is stabilized by polymer fluid. The entire bored length is full of slurry up to top of casing.In most cases this kind of civil works results from the need to build a bridge or executing port structures in places where the creation of temporary artificial peninsulas with fill material is impracticable or not allowed. Hence the need to use floating work platforms, commonly referred to as barges."

Jan 1, 2017

By Sangseom Jeong, Moonkyung Chung, Junyoung Ko

"Abstract The plugging effect of open-ended piles in sandy soil is analyzed by full-scale field test and plugging measurement. PLR (plug length ratio) measurement data from 144 field cases are analyzed with pile diameter. Based on the plugging measurements, PLR of open-ended piles which have above 1000mm diameter is predicted to be above 0.9. Through plugging measurements, a new empirical method is suggested for quantifying the plugging effect of open-ended piles. The proposed PLR equation is possible to predict the behavior of soil plug in the preliminary design stage. In addition, in order to investigate the behavior of the soil plug of open-ended pile, field load tests are performed on instrumented three piles driven into sand. It is obtained that the resistance components of open-ended pile are separated by double-walled pile system. It is found that inner shaft capacity is developed nearby pile tip. However, upper soil plug did not influence the inner shaft capacity. Also, it is found that all test piles are floating piles and unplugged condition because the sum of inner shaft capacity and outer shaft capacity is calculated about 58 to 76% of the ultimate bearing capacity.INTRODUCTIONIn Korea, a number of huge construction projects such as harbor terminals, offshore grand bridges, and lifeline systems are progress in urban and costal area. In these areas, steel pipe piles are frequently used to support high-rise buildings and heavy weight structures for ensuring structural safety rather than serviceability limit capacity. Also, steel pipe piles are frequently used in civil engineering structures because they have many advantages such as high-load bearing capacity, light weight and outstanding workability. The mega foundations of grand bridges and high-rise buildings are required in geotechnical engineering. Large diameter driven piles are frequently used in several projects.Many specifications such as API, FHWA and AASHTO have been reported as a design guideline of plugging effect, however , the current design method for plugging effect of steel pipe piles are mainly based on the our knowledge derived from observation of the model test or the small diameter pile load test. Therefore, these specifications have limitation to apply the large diameter steel pipe piles.Much work has been done to study the plugging effect by many researchers. Yamahara (1964) reported that soil plug has been modeled as a thin disk element as shown in Figure 1, since the increment of radial strain of the soil plug can be neglected due to high rigidity of the pile compared to that of the soil plug. Klos and Tejchman (1977) reported that the end bearing capacity of open-ended piles was almost equal to that of a closed-ended pile when penetration depth of pile was above 15times the pile diameters by model tests. Paikowsky and Whitman(1990) reported fundamental studies on mechanism of plugging effect in sand. Paik et al. (2003) reported that empirical relations for plug load capacity, annulus load capacity, and shaft load capacity of open-ended piles are proposed based on the model pile tests. As discussed above, much work has been done in the area of plugging effect. But little work has been done to study the plugging effect by full scale field tests."

Jan 1, 2014

By Philip Bonanno

The first major project in Boston's new access to Logan Airport was an Immersed Tube Tunnel which extended 3,600 ft. from South Boston to East Boston across Boston Harbor. Twelve tube sections, 300 ft. long x 80 ft. wide x 40 ft. high, were lowered into an excavated trench which was then backfilled. The depth of the trench at mid-channel was approximately 100 ft. below mean high tide. At the East Boston end the tube terminated close to the present shoreline. At the South Boston end the tube terminated approximately 600 ft. inland from the shore line where a ventilation building was required. The depth to subgrade from existing ground at the ventilation structure was approximately 85 ft. The soil profile at this location consisted of 50 ft. of miscellaneous rubble fill, 25 ft. of Boston blue clay, and 10 ft. of glacial till. A small amount of weathered argellite existed at the north end of the structure. Part of the Morrison Knudsen, Interbeton, J.F. White, Joint Venture contract to construct the Immersed Tube Tunnel (ITT) was the construction of a cofferdam at the tube/ventilation building interface. The ventilation building was to be built as part of another contract. The construction of the cofferdam and the excavation to the building subgrade was the responsibility of J.F. White Contracting Company.

Jan 1, 1994

? Hollow Stem Auger ? Drill Bits ? Leads/Torque Arm ? Hydraulic Gearbox ? Hydraulic Power Unit ? Grout Pump ? Crawler Crane

Jan 1, 2000

By d&apos, E. Appolonia

A construction project is successful when all parties contributing to it are winners. It is not a success when there are winners and losers. Con­tractors, engineers, suppliers and equipment developers, and especially owners, each can contribute and benefit from a revaluation of attitudes and contacts from planning to final payment. The Deep Foundations Institute was initiated with this as its major purpose. The help of educators is essential to promote this with the next generation. The Association of Soils and Foundations Engineers has developed guides for "Mediation Arbi­tration of Construction Contracts."

Jan 1, 1985

By Darrell L. Beddard

Pile driving started October 29, 1993 and was completed on January 27, 1994. Field work included driving piling from ground surface at one site and at or near proposed footing elevations for the remainder. Piles were driven to specified tip elevations or the elevations directed by the Project Manager. In an attempt to address what installation technique(s) performed the best, several methods were used, including varied predrilled depths, open ended piles, closed ended piles, and the use of both impact and vibratory hammers. Piles were driven closed ended where possible to study the feasibility of this option to reduce construction costs associated with pile cleanout. Piles were driven to different depths to measure capacity variations. The 24-inch (610 mm) diameter piling were driven in one piece while the 42-inch (1.07 m) diameter piling was driven in two segments. A total of 79 piles were driven for the four sites, 74 of the 24-inch (610 mm) diameter and 5 of the 42-inch (1.07 m) diameter. Various hammers were used to determine which hammers provided viable solutions to the potential problems anticipated in the design phase. Hammer selection was based on the driveability studies. Equipment included a 175 ton (1.56 MN) crane, support crane for pile stabilization, crane mounted auger drill, offshore leads, Delmag D30-32, D46-32, and D62-22 diesel hammers, an HPSI 2005 single acting hydraulic hammer, a Foster IHC S-90 double acting hydraulic hammer and a Kencho VM2-25000AII vibratory hammer with the weights set to produce 17,500 pound-inch (1.98 kN-m) of eccentric moment.

Jan 1, 1996

By Sridhar Krishnan

This paper presents the results of a comprehensive pre-production pile testing programme for the US$ 800 million 1400MW Coal-Fired Jimah Power Plant Project in Negeri Sembilan, Malaysia. The testing programme included high-strain dynamic testing and fully instrumented static axial and lateral load testing of driven prestressed concrete piles and bored cast-in-place piles. A highlight of the testing programme was the pioneering use of the Global Strain Extensometer (GloStrExt) Method, a deformation monitoring system that uses advanced pneumatically- or hydraulically-anchored extensometers and a novel analytical technique to monitor loads and displacements down the shaft and at the toe of driven prestressed concrete piles. The experience with the testing programme for the Jimah Project also demonstrates the possibility of achieving notable breakthroughs, not only in the monitoring, evaluation and reporting of pile foundation behaviour dynamics but also in our understanding of the mechanisms that underpin such behaviour. These significant gains are undeniably a direct result of the committed and co-operative relationship among the project owner, design/builder, specialist piling subcontractors, pile suppliers and pile instrumentation and testing specialists.

Jan 1, 2006

By Mark M. Petersen

As part of the addition of eight new combined cycle generating units at the Florida Power & Light Sanford Plant, 2,129 piles were to be installed. The existing plant elements were supported on driven piles, and the variation in pile lengths during previous work, as well as available subsurface information, indicated a complex stratigraphy. At the request of the owner, the designer/construction manager developed a program to evaluate the use of pressure-grouted displacement piles. A pre-design load test program in areas that represented the apparent extremes in subsurface conditions indicated that the system was feasible; however, the presence of existing features that were to be demolished later precluded the clear delineation of subsurface conditions in advance of construction. A contract was negotiated with the pile installer based on the best estimate of potential pile lengths, with modifications to pile lengths to be set based on additional exploration. A total of 52 cone penetration soundings and five load tests were performed immediately prior to and during pile installation to establish correlations between the CPT data and pile performance. Pile depths were set based on these correlations. Pile installation was completed 6 weeks ahead of schedule and 15 percent under the original budget estimate. This paper documents the evaluation of pressure-grouted displacement piles as an emerging technology, and illustrates the benefits of a close working relationship between the owner, designer, and pile contractor at a site with variable subsurface conditions.

Jan 1, 2002

By A. Holeyman

The displacement compaction piles described in the paper are installed using a heavy casing or tube and an internal drop hammer. The casing which initially is closed at the bottom by a sand plug displaces the surrounding soil during the driving. Additional sand is rammed down through the casing during the extraction of the casing. The applications and limitations of the method are reviewed in the paper. The importance of checking the sand compaction piles during and after the installation is stressed. Indications of the compaction of the surrounding soil during the driving can be obtained by comparing the initial and the redriving logs of the casing as well as from the volume of sand added. A method to estimate the increase of the mean cone resistance as measured by CPT tests in sandy and silty soils is presented. The governing parameters are the volume of the added sand, the granulometric index and the initial cone resistance.

Jan 1, 2010

By Bert R. Oastler

BERT R. OASTLER: Born Atlanta, Georgia, October 19, 1933; B.S. Civil Engineering, Duke University, 1956; Doctor of Laws, Emory University, 1966; Bryan Honor Society; Associate Editor, Journal of Public Law. Partner in charge of litigation for Smith, Currie & Hancock Including federal and state courts, administrative boards, arbitration and negotiation. American Bar Association; American Trial Lawyers Association; Georgia Trial Lawyers Association. Practiced structural steel design at Newport News Shipbuilding & Drydock Company and building construction as an officer in the United States Air Force. Engaged in the building construction business in Atlanta, Georgia as estimator and project manager for five years. Lectured on construction litigation, arbitration and government contracts procurement law for Federal Publications, Inc., Associated General Contractors and other private entities on a nationwide basis. Served as guest lecturer on Government Contracts at Emory University and Georgia Institute of Technology, Atlanta, Georgia. Served as arbitrator in cases for the American Arbitration Association.

Jan 1, 1988

By Jose L. Garcia

The following document aims to cover all issues concerning the three main methods employed for the in-situ survey of concrete pile integrity. Within it are described both sonic coring and low-strain tests and the frequency and time domain analysis of their results, which are the most advanced techniques currently in use in Spain. The survey techniques described were developed and began worldwide deployment in the 1960s, but it was not until the 1980s that they saw large scale implementation in Spain, largely thanks to the miniaturisation of electronics and computer equipment that made them easier to use on-site. Sonic coring, echo and frequency-response testing or mechanical impedance tests are spreading further every day. However, there appears to be a need for standardisation of the testing methods, as well as their implementation, interpretation and the presentation of results. The goal of these Spanish recommendations is to serve as a guideline for test standards and to provide examples for a correct and commonly agreed interpretation of test results, as well as settling any differences in the evaluation of defects detected in foundation works.

Jan 1, 2006

By Michel Bustamante

The occasional substandard performances of continuous flight auger in particular soil conditions have prompted the drilling rig manufacturer to improve the standard CFA in order to reduce its negative effects. A real improvement of interest was the launching of the double rotary CFA system. The promising features of the latter have incited the authors to implement an extensive experimental research on pile constructed using this type of technique but in the specific context of cohesive soils. Short-term static load tests were carried out on a total of 9 test piles of various installation techniques in order to compare the respective performances. The promising features of the double rotary CFA have incited the LCPC & Durmeyer Company to implement an extensive experimental research on this type of pile technique but in the specific context of cohesive soils and more particularly in clayey marls. After load tests completion the research has been completed by an excavation of the double rotary CFA piles. All the collected data concerning the implemented program are reported.

Jan 1, 2002

By Larry Rayburn

In the spring of 1999, construction commenced on the new Steelers Football Stadium in downtown Pittsburgh, Pennsylvania. Richard Goettle, Inc. (RGI) was the successful bidder to install the specified augercast piles for the foundation package. Description - Pittsburgh Steelers Stadium The new stadium will house the Pittsburgh Steelers Professional Football Team. It is widely believed that if a team is provided with a modern playing facility, that a winning season will ensue (Not always the case). The new stadium location is on the north side of Pittsburgh on the Ohio River, and just downstream of the confluence of the Monongahela and Allegheny Rivers. The site is west of existing Three Rivers Stadium. The Three Rivers Stadium was built during the late sixties and housed both the Pirates Baseball and Steelers Football Teams. The Public Auditorium Authority elected to replace this outdated stadium with two new stadiums, one for each professional team. The landmark stadium was imploded in February of 2001.

Jan 1, 2001

By V. M. Troughton

Large diameter bored piles with grouted bases have been adopted for the foundations of the majority of the buildings at Canary Wharf in London's Docklands, including a deep basement car park. The piles are founded in the Thanet Sand which forms part of London's aquifer where water levels are reported to be slowly rising. A special pile test has been carried out to determine the effects of both the basement excavation and a possible long term rise in the groundwater level on the performance of base grouted piles. These effects were simulated by injecting water around the pile toe and thus reducing the vertical effective stress. In this paper the test layout and procedures are described and the results are presented. The test results showed that the reduction in pile base resistance under increased water pressures was less than predicted by conventional design methods based on vertical effective stress. The end bearing resistance was found to be proportional to the mean effective stress.

Jan 1, 1989

By Alan B. Wagner

The River Tower is a proposed 27-story condominium building in the heart of downtown Milwaukee, Wisconsin (USA). The tower will be over 100 m tall, and will have a ground area measuring 15 m by 40 m. The structure will be constructed of cast-in-place reinforced concrete. Certain transfer girders and stabilizing diagonals will be constructed of post-tensioned concrete. Vertical loads will be transmitted through an arrangement of columns, bearing walls, and elevator and stair cores. A mat foundation will be used to connect and integrate these load-carrying elements. The site's geologic profile includes 8.4 m of compressible estuarine (organic) deposits. To control settlement, the mat will be pile-supported. These deposits are underlain by moderate-strength inorganic deposits that extend to bedrock at 32 m.

Jan 1, 2002

By Kazimierz Gwizdala

In the paper the method for estimation of settlement of vertically loaded piles in a group is presented. The method is generally based on the hybrid procedure with non-linear solution for single piles and with interaction between them for the low-strain shear modulus. Some attention is paid to the influence of deformation and strength parameters used in calculations. The applied model is verified in the framework of the research programme carried out recently in the Geotechnical Department of Gdansk Technical University. It concerns monitoring and analysing the settlements of the existing structures on piles. A comparison of calculation and measurements results for two tested buildings is presented as an example.

Jan 1, 2002

By Dan Brown

This paper presents a case study of a cyclic lateral pile load testing program performed on two 18-in square prestressed concrete piles (PSC) in Savannah, Georgia. The load test program was developed to simulate the lateral behavior of a single pile under seismic loading conditions for the design and construction of a large LNG storage tank. The lateral load tests included cyclic loading to measure possible degradation in soil response followed by static loading to large displacements (around 6 inches at the loading point). The lateral load was applied through a reciprocating jack positioned to push and pull the piles against each other. The test piles were instrumented with multiple displacement transducers, downhole inclinometer, and strain gauges. This paper provides an interpretation of the test results regarding the pile performance and soil response to monotonic and cyclic lateral loading. A backfitted computational model of the soil resistance was developed to match the test results using the LPILE computer program. The load-deflection and deflection/moment versus depth comparisons suggest that this model appears to capture the behavior relatively well within the general range of suitability for design purposes. New design curves were developed based on the soil parameters derived from the lateral load test results.

Jan 1, 2003

By Mark R. Svinkin

Construction vibrations may be harmful to adjacent and remote structures, sensitive instruments and people. Construction vibration sources have a wide range of energy, displacement, velocity and acceleration transmitted on the ground. Effects of different dynamic sources and soil conditions on construction vibrations is analyzed. Consequences of construction vibrations are developed in various ways. It is important to assess intolerable vibrations before the beginning of construction activities. Guidelines for preconstruction survey are presented. Pre-construction survey and prediction of anticipated vibrations by IRFP method, monitoring and control of measured vibrations are important steps in preventing intolerable vibration effect.

Jan 1, 2000

By J. Osterberg

A new device has been developed for load testing driven piles and drilled shafts which consists of an hydraulic jack or bellows which has a telltale rod fastended to the bottom. The rod extends upward to the surface through a pressure pipe. When pressure is applied, the jack or bellows expands, applying an equal upward and downward load at the bottom. The downward movement at the bottom is indicated by the rod and the upward movement is indicated by the movement at the top. Thus, upward and downward load-deflection curves can be drawn. As load increases, failure will occur either in end bearing or friction. Results of field installations are described. Total loads of up to 1,100 tons metric have been used. The method obviates the need for the reaction load required for the conventional pile loading test and separates friction and end bearing. It is especially advantageous for use over water, in crowded spaces and for inclined piles.

Jan 1, 1989

By William E. Lardner

Interlocking caisson walls developed from conventional "soldier pile and lagging" shoring. In the latter, the soldier piles receive directly most of the soil load. Natural arches form in the soil behind the shoring; the lagging supports little more than the segment of soil inside the arch. Fig. 1: A typical layout of a lagged wall [ ] Fig. 2: A typical layout of an interlocking caisson wall [ ]

Jan 1, 1987