Search Documents

By R. Chowdhury

The relevance of reliability studies for deep foundations is considered in this paper with special reference to pile foundations. Attention is drawn to uncertainties related to applied loads, the load-carrying capacity and the safety margin of a pile foundation. The essential steps in a reliability study are outlined. An essential goal of any study is the determination of the Reliability Index or Safety Index under different conditions of loading and operation. Calculations concerning probability of failure or success require an assumption to be made concerning the probability distribution of the safety margin. The significance of this and other assumptions should be clearly understood. Reliability approaches should be used to complement conventional deterministic studies.

Jan 1, 2010

By Jorj O. Osterberg

This paper is for presentation at the 14th Annual Members Conference of the Deep Foundations Institute held at the Hyatt Regency Hotel, Baltimore Maryland on October 10, 1989. This is an introductory presentation of a one hour symposium on the applications of a new testing device. This paper discusses how the device works and its uses. Papers following this describe: - How the cell is constructed and calibrated - Two projects on which the device was used on long driven piles to determine the frictional capacity - A bridge project on which the device was used on an instrumented test drilled shaft and a working drilled shaft

Jan 1, 1989

By Vladimir M. Korolev

The field studies conducted at the experimental-production sites allowed to develop the technology of arranging drilling piles in loess subsiding grounds over 25 m deep and over 250 mm in diameter, to select optimal compositions of flush fluids, to assess the carrying capacity and field of use of the piles under test and to produce a special equipment. The dependence of the ultimate axial pressing-in load on pile driving into the non-subsiding section, its diameter and method of fulfillment, as well as the ground moisture dependence of the specific ground resistance along the piles' side surface within the limits of the subsiding section were determined. The study results allowed to reduce the length of the work piles and the number of bars in the reinforcement frames. The obtained experimental data enable to give a preliminary assessment of the piles' carrying capacity under complicated engineering-geological conditions of subsiding grounds.

Jan 1, 2002

By Shamsher Prakash

Estimation of vertical load carrying capacity of a single vertical pile under earthquake loading is an important task of a design engineer. Lateral vibration of vertical pile is highly influenced by the magnitude of vertical load. Several load reversal, during earthquake loading introduce gap between pile soil interface which reduces its load carrying capacity and increases lateral motion. This paper presents a simple time domain numerical scheme to estimate the lateral pile response, considering the loss of contact of pile at pile soil interface, during impact and earthquake loading. The motion of the pile is limited in the vertical plane. Time domain has been discretised into small intervals. The non linearity of soil properties has been taken into account by discretised Winklers model with Wolfes frequency independent mass spring dash pot coefficient for geometric damping. Suitable software has been developed which keeps track of the load reversal point of each elements.

Jan 1, 1996

By Shawn Downey

A helical pile with in-situ grouted shaft was used to underpin the existing slab of a large retail store in the Edmonton, Alberta Canada area. The existing structural slab did not have the capacity to support the increased load requirements. The design to upgrade the capacity specified a drilled shaft as the deep foundation to underpin a portion of the slab. A helical pile was quoted as an alternate and ultimately won the bid based on the advantages of the system. After an ASTM D1143 Quick Load Test confirmed the axial compression capacity, 723 helical piles with grouted shafts were installed in 3 weeks underpinning 40% of the 93,000 ft2 (8,660 m2) building.

Jan 1, 2003

By Cornelis Van Der Veen

Foundation piles, partly passing through unconsolidated compressible layers, suffer a downward drag that is called negative skin friction. The negative skin friction depends on the movement of the surrounding unconsolidated soil relative to the pile and on the friction between pile and soil as a function of that movement. The negative skin friction adds to the load on the pile. However as it is a function of the pile movement relative to the soil, the amount of negative skin friction to be taken into account to determine the allowable bearing capacity depends on the allowable pile settlement. In this paper this property is indicated by the factor µ. As under the conditions of ultimate pile bearing capacity negative skin friction does not occur, a factor of safety is introduced, which is lower than normal. Eventually a formula for the bearing capacity is given in which µ and both figure. The exact values for given circumstances have to be determined empirically. A few examples are given.

Jan 1, 2010

By Kirty Dave

Foundations in any contract are the most uncertain parts of the contract and most of the "Construction-Contract-Disputes" are either directly related to foundations or arise as 'Side-effects of changes in promises related to foundations. Foundation Engineering is defined as ' The art of selection, designing and constructing the elements that transfer the weight of structure to the underlying Soil or Rock." (Ralph B. Perk). This art started becoming a science since 1920, when scientific efforts to determine the behaviour of sub-surface materials were made. The art and science merged to give new techniques and the science started dominating the field as more and more refinement came in techniques to predict more accurately the characteristics of the sub-surface elements. Inspite of good thorough investigations and design, the contractual promises drafted could leave some room for differences between the parties and above all the prudency expected of both the parties may fall short of the expectations raised in the contract. This may give rise to disputes which may need to be resolved as per principles of law. This paper attempts to initiate a dialogue amongst Foundations-Engineers and Contractors as to how do we minimise the differences arising out of or related to contracts concerning "Foundations".

Jan 1, 1996

By Trevor I. Addenbrooke

Stress reducing piles were used for the first time at the Queen Elizabeth II Conference Centre near the Palace of Westminster in London, UK. The inclusion of these piles directly beneath heavily loaded columns was to reduce the high anticipated bending stress in the foundation raft, and to eliminate local yield of the London Clay beneath the column locations. Load cells were placed in one of the stress reducing piles during construction. The data showed that the pile carried about 30% of the column load. This can be contrasted with conventional piled raft design where the pile carries upwards of 80% of the column load. The build up of load on the pile and pile displacement have been accurately reproduced using coupled finite element analysis. These numerical results demonstrate the value of geometrically simple axially symmetric analyses for modelling a pile-enhanced raft. On site, excavation preceded construction of the raft and subsequent pile loading. Failure to model this construction sequence caused the shear strength to mobilize at the base of the pile first, during loading, whereas following the construction sequence caused the shear strength to mobilize at the top of the pile first.

Jan 1, 2002

By E. Ulrich Klotz

It is difficult to predict accurately the capacity of driven piles in sand. In practice, this uncer­tainty either leads to conservative designs if the capacity is under-predicted, or worse, if the capacity is over-predicted, it can lead to severe foundation problems. One significant possible cause of the problem is that currently available semi-empirical design methods do not capture the fundamental mechanisms that govern the load capacity of driven piles in sands. As part of a recent research project at City University centrifuge tests on a driven model pile in sands have been undertaken. A fully instrumented model pile was constructed and pushed into samples of quartz and carbonate sand thus covering a wide range of mineralogies. Tri-axial tests were used to determine the fundamental patterns of behavior of the sands. This allowed a general framework to be established, in which the in situ stress:volume relationship is shown to govern the capacity of the pile. The paper sets out with a brief introduction of the experimental techniques used in the study. The results of the pile tests are discussed in detail with particular attention given to distribution of the radial stresses along the pile shaft. Existing design methods for piles in sand are then discussed in the light of the new understanding gained from the research, highlighting their deficiencies and suggesting an improved approach.

Jan 1, 2002

By Gordon King

This paper presents a case study of large diameter continuous flight auger (CFA) piles and drilled shafts utilized for foundation support of a series of heavily loaded cement plant structures at the Suwannee American Cement (SAC) Plant in Branford, Florida. The high loads and exacting total and differential settlement criteria when combined with a highly variable subsurface geology provided a challenging design scenario. Fully instrumented static pile load tests were performed to determine design parameters in the variable weathered limestone bedrock. Ultimate side friction values ranged from 2 to 8 tsf within the limestone, resulting in the requirement for CFA piles up to one meter (approximately 40 inches) in diameter and socket lengths of up to 40 feet. At several localized areas, the limestone bedrock was in excess of 60 feet below grade, requiring the use of cased drilled shafts to depths on the order of 80 to 90 feet. An integral part of the production pile installation was the use of instrumentation to monitor drilling and concreting parameters. Calibration of drill rates, torque and auger rotation with rock quality was performed to allow monitoring of the soil stratigraphy at each pile location. When combined with the results of the instrumented load testing, the monitoring of drilling parameters allowed confirmation that sufficient socket length was achieved within the quality of rock present at each and every pile location.

Jan 1, 2003

By Saba Mohan

This study presents results based on the Pile Installation Demonstration Project (PIDP) that was conducted as a part of the East Span San Francisco-Oakland Bay Bridge Seismic Safety Project. For the three full-scale pile installations, two different high-energy hydraulic hammers were selected for the installation. However, these hammers may not have sufficient energy to drive these large diameter piles at their ultimate capacity following long-term set-up. Nevertheless, these hammers were selected because, soil plug behavior, the generation of excess pore pressures and remolding of soil during driving were expected to reduce the shaft and end bearing resistance, and therefore reduce the energy required to drive these piles to design penetration. Data collected during continuous installation driving and after a series of re-strikes at different set-up times ranging from 1 to 33 days were used as input data for CAPWAP. These results were used to estimate the soil resistance along the pile length and at the toe of the pile, and the soil pile set-up behavior. Validity of the procedures used to predict the soil resistance to driving and predicted blow counts were verified with the field observed blow counts and the energy that was delivered to the pile. Based on combined CAPWAP analyses, the soil pile set-up with time was estimated and compared with results of other methods currently available in the literature for predicting the soil pile set-up rate.

Jan 1, 2002

"Boston’s Central Artery passes beneath nine active railroad tracks carrying commuter and Amtrak trains into South Station, the City's busiest rail terminal. These railroad operations had to remain in service throughout the construction of the “Big Dig”. The solution was to jack the tunnel under the tracks, rather than build the tunnel by more conventional means.Jacking of utility pipes is fairly common, but jacking boxes as big as a highway had never been done in North America, until the Big Dig came along.Soil freezing was decided upon as a means of stabilizing the soil under the tracks. This allows the tunnels to be jacked into place without soil caving when the soil is excavated at the leading face of the advancing tunnel boxes. Hundreds of pipes were driven into the ground between the tracks. Inside the steel pipes were smaller plastic pipes. A freezing plant near the railroad tracks pumped refrigerated brine into the inner plastic pipes. The brine ran out the bottom of the inner pipe, flowed up to the top inside the outer pipe, and was re-circulated to the freezing plant and back again into the ground. Over several weeks the circulating brine drew the heat out of the soil little by little, and froze the ground outward from the pipes. Soil FreezingThe plan required the construction of jacking pits in which the tunnel boxes could be constructed, and from which they could be jacked forward to their final locations, as described in the accompanying article. Once the jacking pit was built and the tunnel box constructed inside the pit, crews made an opening in the headwall of the pit to allow passage of the tunnel sections, excavated about three feet of the frozen soil, pushed the tunnel box ahead, and repeated the procedure again and again."

Jan 1, 2003

By P. Middendorp, Gerald E. H. Verbeek

"INTRODUCTIONStatic Load Testing (SLT) is generally considered the pile testing method that provides the de-facto answers regarding pile capacity and load-deflection behavior. However, as this testing method is time consuming and costly, alternative pile testing methods are applied, such as High-Strain Dynamic Testing (HSDT), commonly referred to as Dynamic Load Testing (DLT), and Rapid Load Testing (RLT), which includes Statnamic Testing (STN) and the Fundex Pile Load Tester (PLT). Extensive descriptions of these pile testing methods as well as comparisons of the results from these two methods have been widely published, but little is written on the choice between HSDT and RLT. This article will address this issue for concrete piles by discussing five different aspects that should be considered when making a choice between HSDT and RLT for either cast-in-situ piles or precast driven piles. TIMINGThe timing of the pile load test is independent of the testing method. For cast-in-situ piles load testing is performed some time after the pile has been installed (to allow the pile to obtain the compressive strength required to withstand the test load), while for precast driven piles load testing is performed after a so-called set-up period following pile installation (to allow the soil to recover from driving induced disturbances and, at least in most cases,regain strength).In other words, the timing of the test does not affect the choice of the testing method.ACCURACY OF THE APPLIED LOADWhen a pile is tested by RLT the applied load is measured by a calibrated load cell placed on the pile head, just as it would be during SLT. This means that the error in the applied load value is less than 0.1% of the maximum range of the load cell.However, when a pile is tested by HSDT the load is calculated from the measured strains, which means that the outcome is dependent on the pile material properties. In this case the applied load (F) on the pile head is calculated by multiplying the measured strain (?) with either the calculated or estimated elastic modulus of concrete (E) and the pile cross section (A).The elastic modulus is generally back calculated from the (average) stress wave velocity (c), which in turn is derived from the reflection time (T) it takes for a stress wave to travel over the pile length (L) from the pile head to the pile toe and back to the pile head."

Jan 1, 2006

"After the non-destructive testing is completed, the data must be compiled, evaluated, and interpreted. During this process, the data may indicate that there is an anomaly warranting further investigation, which may eventually be determined to be a flaw or defect. The definitions of an anomaly, flaw, and defect can be described as follows (after Amir, 2002):Anomaly - Any irregular feature identified in the NDT graphic results. An anomaly may be due to the testing instrumentation (such as noise), to the means used to perform the test (e.g. access tube debonding in CSL) or to the shaft itself. It is the responsibility of the NDT practitioner to gather and analyze all relevant data and try to resolve every anomaly before it is declared a flaw or defect.Flaw - Any deviation from the planned shape, size and/or material of the shaft.Defect - A flaw that, because of either size or location, may detract from the shaft’s intended performance or durability. The geotechnical engineer and the structural engineer are jointly responsible to decide which flaw comprises a defect.This section describes the process of evaluating the data, determining if an anomaly exists, and if so, deciding whether the anomaly is actually a flaw or a defect. If the anomaly is determined to be a defect, its effect on the performance of the shaft must be evaluated, and if necessary, the can be re-engineered, repaired, or replaced."

Jan 1, 2004

By Christian Hoyme, Jochen Maurer, Hans Regler

Up to today, it has been very difficult to obtain qualitative and quantitative information about the status and production process of a construction site. It is becoming more and more important to be able to analyze this process so as to notice bottlenecks and interruptions on the site early on. The high costs of each shift in special foundation industry mean that making the wrong decision and/or interruptions can put the financial result at risk. Previously, keeping reliable data meant manual process documentation. This was done either by an additional staff member (incurring high additional costs for training, education, etc.) or by the equipment operators. The latter is critical, because they have to initiate every process step change, leaving no time to log data separately. Studies have shown that there are considerable deviations from the actual process steps. In this paper, a seamless, automated method will be introduced to analyze the construction process. This method recognizes each process step from the equipment data. The main purpose of the data recorded by the piling rig is the need of quality reports and now basis for the presented analysis. Here, a method was successfully transferred from theoretical computer science (compiler construction field) to find application for process recognition. Because the execution of works in special foundation construction can always be defined sequentially and therefore also practiced sequentially, recognition can occur step-by-step. Our method always recognizes the next step, so it does not have to monitor as much data at the same time. Individual trigger points are easier to define. Unlike solutions that are based on a global approach and allocate suitable process steps to data patterns, thereby also creating gaps, the presented method is always seamless. Furthermore, this method can be applied regardless of time or location provided that the necessary machine data is available, which is normally the case with production data logging. This means that construction sites even from the past can also be analyzed and the results used for comparisons. The first results from the analysis of a complete continuous flight augering (CFA piles) installation process of a construction site will be presented.

Sep 8, 2021

By Lynn Crayne

We used Glyoxal as the hardener, at a final concentration of 10% by volume and therefore 20% by volume in the A-Component. They worked pretty well what we did was we shaved the joints on each of the pipes when we assembled them so they wouldn't rip the packers and then we greased the packers very well going in. We had to replace some but we have any getting stuck or didn't lose any pipes.

Feb 10, 2003

By Helen Ahnberg

The scope of the present paper is limited to report the experimental evidence and not for describing the analytical assumptions. However, the idea behind the experimental program is that the deterioration may be caused by the leaching of Ca from the treated soil to surrounding soil or water driven by the difference in the Ca ion concentration. As a consequence of Ca leaching, it may be natural to expect the expansion of micro void space within the treated soil. In a saturated condition, the water inflow into the treated soil may accompany the leaching phenomenon. We measured the water content within the treated soil. But there is not much difference in water content within the soil.

Feb 10, 2003

By Andrew Baxter

The Crystal Bridges Museum of American Art in Bentonville, Arkansas is a beautiful glass and concrete structure cut into a valley that mingles with water ponds spanned by multiple bridges with suspended roofs. Or, at least it will be when completed in 2009. At Crystal Bridges, most of the proposed buildings involve cuts up to 50 ft high to be retained by the building structures. This requires the construction of retaining walls adequately founded to support lateral loads of up to 70 kip/ft. To add to this difficulty, the site is within a karst region with all the variability and irregularities associated with solutioning and erosion of the parent rock in this environment. The irregular rock profile made it virtually impossible to conceive a predictable arrangement of shallow footings and shear keys for the retaining walls. The existence of layers of soft soils within a hard rock formation made a caisson foundation impractical. The authors developed an innovative solution based on micropiles, which proved to be invaluable from a cost and schedule point of view. In areas where rock was shallow, micropiles were used as ?shear pins? to transfer the horizontal loads to the rock. In areas with significant overburden, a system of vertical and battered micropiles was devised to carry vertical and horizontal loads from the retaining walls. This paper presents a detailed description of the design and installation of the micropiles used as shear pins, and includes the results of lateral load tests performed on full-scale models of the grade beams on shear pins. The work performed shows that micropiles in rock can be effectively utilized for support of significant lateral loads provided that an adequate arrangement of suitably sized micropiles is provided, and that micropiles used as shear pins may develop significant tensile stresses when loaded laterally.

Jan 1, 2008

By Thomas J. Kennedy, Michael D. Bennett

The study of geotechnical history is well-established. Most geotechnical practitioners, teachers, and graduate students have some grasp of the origins of the field. However, this understanding often consists of a jumble of names and anecdotes. This paper discusses how a deeper comprehension of geotechnical history can benefit academia and practice alike and describes how the authors have begun a wide-ranging study of the subject. The paper reviews the dual-track methodology the authors have generated for the study, which consists of written articles about different works in geotechnical history and a database tracking how often pieces have been cited in geotechnical literature. The first technique has shed light on aspects of geotechnical history such as the connection of the Darwin family to the origins of geotechnical engineering, the St. Francis Dam failure of 1928, and the rivalry between theoreticians and practitioners in the early days of the field. The second has helped quantify subjects such as the outstanding contributions of Karl Terzaghi, the disagreements between Terzaghi and Donald Taylor, and the specialization of the field over time. The paper concludes by discussing the authors’ planned future work on geotechnical history.

Oct 1, 2022

By Z. Q. Bian

The wireline sampling originates from core drilling in rocks. The authors combined the wireline sampling technique with conventional undisturbed soil samplers, including Osterberg sampler, Denison sampler and double tube barrel, and then developed the wireline samplers of WPS, WSS and WSR models. These samplers are able to sample various soils. They reserve all the advantages of the original samplers, and moreover, they are noted with quick hoisting and lowering by wire rope. Therefore, it becomes an efficient new technique of sampling undisturbed soil from deep foundation.

Jan 1, 2010