Search Documents

By S. Banisi, M. Poorkani

The Sarcheshmeh copper deposit contains 1 billion tones of ore averaging 0.7% copper and 0.025% molybdenum. It is located southeast of Iran and currently processes 41,000t/d. Molybdenite as a by-product is recovered in two separate stages. First, a bulk coppermolybdenum concentrate is produced and in the second stage these two are separated. The recovery of molybdenite in the first and second stages is 65% and 85-90%, respectively. The yearly production of molybdenite concentrate varies between 3500 and 4000 t. Sodium sulphide is used as the depressant of the copper and iron bearing minerals which due to a rather high consumption (17.7 kg/t) constitutes one of the major cost items of the plant (i.e., 58% of total reagents cost). A detailed laboratory scale study showed that replacing air with nitrogen could reduce the consumption of sodium sulphide (i.e., H2S or mineral origin). Nitrogen for the plant was supplied from an oxygen plant used for the smelter through a 1400 m long pipeline. The existence of the oxygen plant at the Sarcheshmeh complex was a key factor in the implementation and success of this project. After using nitrogen in the plant for a period of twenty one months, the consumption of sodium sulphide was reduced from 17.7 to 14.2 kg/t at constant metallurgy. The reduction was lower than expected which was mainly due to the type of sodium sulphide used and the lack of any automatic instrument to control the depressant (sodium sulphide) dosage. The latter in turn caused the operators to overuse sodium sulphide in order to reach and maintain the target metallurgy (i.e., higher molybdenite recovery along with lower copper content of the concentrate).

Jan 1, 2005

By Antônio Peres, Rogério Guimaraes, Lauro Takata, Harold Wyslouzil

"Serrana’s concentrator, in Araxii, has capacity of producing approximately 800,000 tomes of phosphate rock per year, with a P205 grade of 36%, from ores grading between 13% and 14% P205. The annual mining rate is around 3.5 Mt and the apatite is concentrated according to the following sequence: crushing, grinding, desliming, flotation and low and high intensity magnetic separations.Two industrial flotation columns (3.0 m x 4.5 m x 14.5 m) were commissioned in 1993 as a replacement for circuits of barite and apatite fines flotation. In 1994, four additional flotation columns of the same dimensions were put into operation, replacing 42 Wemco mechanical cells (300 ft3 each), in the barite pre-flotation, coarse apatite (two columns) and tailings regrind flotation Circuits. Overall, 66 mechanical cells (300 ft3 each) were replaced by only six flotation columns, designed by Cominco Engineering Services Ltd - CESL.The present paper describes the stages of process development, pilot plant testwork and implementation of the industrial project, highlighting the most relevant aspects of each of them. The results achieved are related to improvements in flotation selectivity, gains in P205 recovery and better process control, resulting in better quality products and lower production costs. Other benefits included a decrease in flotation reagents, electrical energy and maintenance materials consumption. These factors contributed to a significant decrease in the cost of phosphate rock production at Serrana, in Araxa - M G."

Jan 1, 1999

By Jose R. Hernandez-Aguilar

"Three models to predict the effect of bubble size (Db) on metallurgical response were tested in a pilot-scale flotation column at Teck Highland Valley Copper mine. The column was fed with slurry collected from the Cu/Mo separation circuit. The first model was the one developed by Gorain et al. (1997), which assumes that the collection zone rate constant (kc) is inversely proportional to Db. The second model was the one proposed by Hernandez-Aguilar et al. (2010), which considers kc as an inverse square function of Db. The third model was the one developed by Yoon and Luttrell (1989) which provides expressions to describe the efficiency of particle collection (E) based on first principles. The results showed a significant bias between experimental and predicted data using the model of Gorain et al. (1997), possibly reflecting the model’s inability to explain the impact of bubble size, bubble rise velocity and flow regime on E. The model of Hernandez-Aguilar et al. (2010) well described the experimental evidence. The model of Yoon and Luttrell gave accurate and unbiased predictions. However, Yoon and Luttrell’s approach calls for a criterion to determine whether the flow regime is potential or intermediate, a subject that requires more fundamental research.INTRODUCTIONParticle collection, i.e., bubble-particle collision followed by attachment, is the basis of flotation. In a quiescent environment (such as the one observed in a column, or away from the impeller in a mechanical cell), a collision event can take place as long as the “degree of turbulence” caused by the rising bubble does not prevent particle and bubble to flow in close proximity. Upon collision, the particle slides on the bubble surface for a period of time. If the particle is hydrophobic, attachment occurs when the “sliding time” is longer than the “induction time”, which is the time required to thin and rupture the intervening liquid (usually water) film forming a three-phase contact angle. While the induction time is largely influenced by the degree of hydrophobicity of the particle, the degree of turbulence is governed by the bubble size. Generally, direct control of bubble size is not exercised by most mineral processing practitioners, in spite of its obvious importance. Studies to model the effect of bubble size on particle collection using fundamental approaches have been conducted (e.g., Anfruns and Kitchener, 1977; Webber and Paddock, 1983; Yoon and Luttrell, 1989; Dai et al., 1999). However, these models have been validated under highly idealized laboratory conditions (micro-scale experiments using single minerals and uni-sized bubbles), far from resembling those existing in practical industrial applications. Fundamental studies to interpret the effect of bubble size on particle collection in industrial environments are largely absent in the literature. Partly because of this lack of practical knowledge, many mineral processing practitioners perceive laboratory “bubble size” studies to be valuable academic exercises, but not something that can be directly applied to daily production issues."

Jan 1, 2011

By T. G. Joseph

A strain-softening constitutive relationship is introduced that describes the post-failure stress-strain curve for rock regardless of whether the rock is intact or broken. The core of this relationship is an ?apparent friction? concept that relates the post-failure apparent cohesive and frictional characteristics of the rock to the strain. The relationship can be determined for a given rock via a series of tri-axial strength tests establishing the peak strength and corresponding strain for a range of confining pressures, together with the determination of the base angle of friction via a simple tilt test. The postulates and assumptions used in deriving this relationship are verified from results of tri-axial tests on both intact and broken rock.

May 1, 2002

By P. Scinto, A. Festa

"Orway Mineral Consultants Ltd (OMC) as a consultancy has specialized in comminution circuit design for over 30 years. The OMC Power Model is OMC’s in-house software for specific grinding energy power-based circuit calculations. The model uses ore hardness parameters from testwork, circuit configuration, equipment geometry and operating conditions as inputs. The model combines proprietary and published power models to predict the total specific energy and the specific energy for each of the components of the comminution circuit. This makes the software a valuable tool for the design and validation of JKSimMet modelling or actual plant performance. Proprietary calculations have been developed and reconciled with over 100 plant benchmark projects encompassing a variety of comminution circuit configurations.This paper describes the OMC approach for determining power requirements for the design of grinding circuits. The accuracy of the OMC Power Model software is confirmed through plant survey benchmark performance and comparisons are made with other power modelling techniques. Practical examples are presented, showing applications for single stage SAG (SS-SAG), SAB and SABC circuit configurations.IntroductionConventional low throughput grinding options, consisting of multi-stage crushing followed by rod and ball mills, have almost become obsolete in the move to higher milling rates required to process lower metal grades. Grinding circuits with fully autogenous (AG) or semi-autogenous (SAG) mills, often combined with ball mills are now the standard to meet the high capacity requirement for processing ores with lower metal grades. Simulation software and power-based equation methodologies have been established for designing AG/SAG based grinding circuits and predicting their energy requirements.Presently, power-based equations remain the principal method for designers to size mills and estimate the power requirement for comminution circuits. The technique is simple and it relies on the design to specify a feed and product size plus a hardness index to produce a specific energy value (kWh/t). The desired throughput of the mill is multiplied by the specific energy to give the mill power requirement, which is used in turn to size a mill for dimensions, internal geometry and loading conditions to match the power draw."

Jan 1, 2015

By Ronald Molnar

"High demand for metals is driving the exploitation of lower grade and more complex orebodies. These projects are often the initiatives of junior mining companies with limited financial resources. In addition, existing operations seek to enhance revenue from their existing metal recovery operations, through the production of value-added by-product metals and chemicals. Typically, hydrometallurgical circuits, often with novel chemistry, are required to exploit these new ores, to produce the multiplicity of products that will make a marginal project economical, or to increase the product range of an existing operation. Often, the mineral processing engineer is given the task of coordinating the development of a back-end hydrometallurgical flowsheet for their mineral processing project. This paper discusses the objectives that companies have when they commission the operation of a hydrometallurgical pilot plant. The paper goes on to enumerate some of the principal differences between mineral processing and hydrometallurgical pilot plants and the effect these have on the design, operability and potential pilot plant outcomes. Important factors include working with chemically reactive solutions and pulps, elevated temperatures operation, changing rheological properties of slurries, the complexity of integrated circuit flowsheets with long hold-up times and multiple recycle streams, and the need in some cases for extreme attention to purity and cleanliness. Examples will be drawn from the extensive experience base of SGS Minerals Services at the Lakefield site, in piloting both mineral processing and hydrometallurgical process flowsheets.INTRODUCTIONWe are currently experiencing a period of strong growth in the demand for metals. This in turn is turning the spotlight on a great many smaller mining companies and mining promotion ventures trying to tap into the rising metal demand. Some of these companies want to develop their properties and recover metals while others want to develop to the point that a major company will take an interest, or in some cases buy them out completely.With the heightened interest in metals, many orebodies that have been known about for years are being reconsidered for exploitation. Often, the reason they have not been developed to date is because of difficult metallurgy and marginal grades leading to marginal economic viability. In both cases the key that unlocks the resources is often the application of a novel metallurgical flowsheet, often a hydrometallurgical flowsheet."

Jan 1, 2006

By L. J. Vincze

The high cost of constructing mineral processing plants in remote locations warrants a close examination of the alternatives available for reducing the amount of on-site construction work. Among the alternatives are portable process plants, modular design and barge mounted plants. Each alternative has certain advantages as well as limitations depending upon specific conditions. On the basis of practical experience and engineering analysis, the paper examines the potential benefits to be realized by these techniques and summarizes the conditions required to obtain them. The potential savings indicated by such studies should encourage consideration of innovative design features for new plants located in remote areas.

Jan 1, 1980

By Carlos Avalos Casillas, Saul Ortiz Landeros

The current work shows metallurgical results obtained at the Centro de Investigación y Desarrollo Tecnológico (Peñoles CIDT), as a continuation of the work first published in February 2012. With the aim of optimizing the economic values of the products, ores from San Julian (Fresnillo) were selectively floated to produce a lead concentrate and a zinc concentrate containing high silver values. In the laboratory, this included regrinding of the rougher and scavenger lead concentrate to increase the liberation of mineralogical species and thus lower zinc recovery. Cyanide leaching bottle tests were conducted to improve the value of the silver. It is proposed to leach the silver contained in the zinc concentrate and then recover the silver using the Merrill Crowe process. The results show a reduction of zinc recovery in the lead concentrate from 11.3% to 2.0% after regrinding to a P80 of 10 microns, improving the metallurgical quality and economic value of the lead and zinc concentrates. Also laboratory and pilot scale cyanidation tests showed that about 65 to 80% of silver will be leached from the zinc concentrate, after regrinding to a P80 of 10 microns. The proposed processing increases the economic recovery of silver from 72.7% to 78.8%.

Jan 1, 2014

By T. Lux, M. Hanel, Degel, A. Filzwieser, R., H. Joubert

It is the increasing demand for an economic and cost saving operation mode that requires effective cooling in order to achieve low refractory wear and good furnace lifetime, which is making cooling technology an important aspect of furnace operation. In addition, the requirements for safety are getting more and more into focus. However, the use of water—today’s standard cooling medium—has major drawbacks as it can cause problems both during furnace start up and operation, namely hydration problems, corrosion, and explosion. Not to forget the severe risks for the operators as well as economical damage in case of a malfunctioning water cooling system. With this new and patented cooling technology ILTEC and the ionic liquid IL-B2001 as the cooling medium, it is possible to realise a water-free cooling solution and therefore the door is wide open to rethink existing and conventional cooling solutions. Furthermore, there is also the chance to recover heat from the process in a more efficient way. However, since the technology is novel and unique there are a lot of concerns and doubts regarding safety for plant operators and employees. The paper is intended to cover both: highlighting the enormous potential of the technology but also to eliminate concerns mainly caused by rumour and unawareness. INTRODUCTION All of us are aware of the risks when water is used as a coolant and placed in the vicinity of the liquid metal phase. Unsuitable design solutions or wrong operation modes of the furnaces or failures of refractories can cause a direct contact of water with liquid metal. The consequences can lead to equipment failures, vessel destruction but even worse to injuries and even fatalities. Over the past decades, countless incidences were reported. Fatal accidents caused by water coming into contact with liquid metal happen every year (Oterdoom, 2014; Filzwieser, Konetschnik, Filzwieser, Wallnerm & Preiss, 2014). With the novel ionic liquid cooling technology virtually all negative effects of a water cooled system regarding safety are eliminated and even additional benefits can be provided (Voermann, Ham, Merry, Veenstra, & Hutchinson, 1999;Verscheure, Kyllo, Filzwieser, Blanpain & Wollants 2006; Wallner, Filzwieser & Kleicker 2006). The fact that no explosion occurs when IL-B2001 gets in contact with molten metal results in a revolutionary solution for the metallurgical industry in terms of safety—new safety standards can be achieved.

Jan 1, 2019

By Tim Martin, Dave Tahija

"In April, 2014, Hecla's Greens Creek mill, near Juneau, Alaska, switched from sulphuric acid to the use of dissolved carbon dioxide for lead flotation circuit pH control. The Greens Creek mine uses paste backfill, in which mill tailings are mixed with cement and used to fill mined areas. Some backfill inevitably becomes part of mill feed during subsequent mining cycles, resulting in high feed pH levels and increased dissolved calcium in the lead flotation circuit. Sulphuric acid is traditionally used to lower pH in such cases but it produces undesirable side effects, including poorer lead-zinc separation and unstable froth. The amount of sulphuric acid used at Greens Creek was limited due to these effects, resulting in higher than target pHs when feed backfill content was high. Dissolved carbon dioxide can be added without these limitations so pH levels have been under much better control since the switch. Additionally, lead-zinc separation and froth characteristics have significantly improved.IntroductionThe Greens Creek Mine, owned by Hecla Greens Creek Mining is an underground mine located on Admiralty Island near Juneau, Alaska, producing silver, gold, lead and zinc in the form of lead and zinc flotation concentrates and a gravity gold concentrate (McDonald, Morgen & Hancock, 2012). The lead and zinc concentrates are produced in conventional flotation circuits preceded by a graphite removal flotation step.The underground mine utilizes cemented paste backfill, of which a certain amount is inevitably re-mined in later mining cycles and returned to the mill, mixed with fresh ore. The Portland cement used in the paste backfill is highly basic so that, from the point of view of the mill, the net effect is to introduce a good deal of lime to run-of-mine mill feed, producing a very high natural pH. This high pH needs to be lowered to obtain good metallurgical results."

Jan 1, 2016

By Tony Lipiec, Greg Gosson

"When it comes to new mines being developed, there is a general industry consensus that most low-hanging fruit has been picked. Many projects currently in the mine development pipeline have been around for decades, but were held back because of technical challenges. Future development of these deposits will likely require access to the public capital markets, and in Canada that means providing scientific and technical disclosure on these deposits in compliance with NI 43-101. As many of these “challenged” projects have metallurgical issues, the companies that own the projects need to ensure their metallurgical Qualified Persons provide transparent disclosure regarding proposed solutions to those issues.This paper provides an overview of the disclosure requirements under NI 43-101 that are pertinent to metallurgists, and other Qualified Persons who prepare technical disclosure regarding the metallurgical characteristics of a mineral project. It lists the triggers for a technical report under NI 43-101 and Canadian stock exchange policies, and identifies the sections of the report that should involve input from a metallurgist or process engineer. It briefly outlines new civil liabilities under Canadian securities laws that increase the possible consequences for not complying with the technical disclosure standards.These materials are provided for general information purposes only and do not constitute legal advice. Readers are advised to seek specific legal advice from their own legal counsel in relation to any decision or course of action contemplated."

Jan 1, 2010

By J. Miettunen

"The lining of a grinding mill has an important role in creating the conditions for the grinding process. The main purpose of the lining is to transfer the energy taken by the mill motor to the contents of a mill. The power draw curve of the mill, if measured with sufficiently short intervals, describes how well the lining works in lifting and mixing the material to be ground.The power draw curve can also be used for determining the volumetric filling of a mill. This new measuring technique was developed at the Pyhasalmi concentrator in 1989-90. The measuring device with its PC-connections offers an excellent tool for controlling volumetric mill filling, for maximizing throughput and for research purpose (e.g. process studies, mill linings design).The paper describes the new method and the results achieved at Outokumpu's concentrators.INTRODUCTIONVarious methods have been developed for measuring mill load; weighing, noise, etc. Weighing is one of the most reliable methods but installing the sensor to existing mills is often difficult. Besides the load measurement does not indicate the volumetric filling if the specific gravity of the mill feed fluctuates. Noise measurement has often failed with its sensitivity to various disturbance sources.As known, the power draw measurement is one of the most accurate measurements in grinding circuits and therefore it has been utilized in sophisticated control, e.g. in power peak seeking algorithms for maintaining maximum grinding efficiency.About 10 years ago power oscillation measurement was developed at Pyhasalmi concentrator. In this method the amplitude of the oscillation caused by the lifters was measured. The oscillation amplitude and the mill filling has quite a good correlation and together with the power draw measurement it could be used for maximizing mill throughput (Koivistoinen and Miettunen, 1989). The main difficulties in this method were that the dependence between mill filling and the amplitude is unlinear and that the dependence also is individual for each mill.The method developed during 1989-90 is also based on the power oscillation but on its phase shift. In principle level of the material in a mill is measured. The method has been successfully used for maximizing throughput at Pyhasalmi and Enonkoski concentrators and at Harjavalta slag concentrator."

Jan 1, 1991

"The measurement of error in assays collected as part of a mineral exploration program or mining operation historically has been undertaken in a variety of ways. Different parameters have been used to describe the magnitude of relative error, and each of these parameters is related to the standard measure of relative error, the coefficient of variation. Calculation of the coefficient of variation can be undertaken in a variety of ways; however, only one produces unbiased estimates of measurement error: the root mean square coefficient of variation calculated from the individual coefficients of variation.Thompson and Howarth’s error analysis approach has also been used to describe measurement error. However, because this approach utilizes a regression line to describe error, it provides a substantially different measure of error than the root mean square coefficient of variation. Furthermore, because regression is used, Thompson and Howarth’s results should only be used for estimating error in individual samples, and not for describing the average error in a data set. As a result, Thompson and Howarth’s results should not be used to determine the magnitudes of component errors introduced during geochemical sampling, preparation, and analysis.Finally, the standard error on the coefficient of variation is derived, and it is shown that very poor estimates of relative error are obtained from duplicate data. As a result, geoscientists seeking to determine the average relative error in a data set should use a very large number of duplicate samples to make this estimate, particularly if the average relative error is large."

Jan 1, 2007

By Matthew A. Perras

With growing populations, infrastructure projects are utilizing underground space to expand transportation networks, water supply and sewer disposal systems and hydropower facilities. These new projects require large diameter tunnels to meet the growing demands. As the tunnel diameter increases, not all rock mass properties are scalable and precedent experience becomes less reliable. One such non-scaleable property is lamination thickness. Numerical modelling was conducted to determine the influence of lamination thicknesses on a 16 m diameter tunnel. Five different areas of excavation response were found to exist for laminations ranging between 0.16 to 16 metres in thickness. For this tunnel diameter, critical lamination thicknesses of 6 metre and 1 metre were found to exist. Above 6 metres the excavation response was similar to isotropic models. Below 6 metres the stresses and yield are channeled by the lamination boundaries, increasing plastic deformation. Below 1m multiple lamination units become unstable and the displacements increase significantly and the shape and extent of the yield zone size changes dramatically. The yield zone is controlled by bed deflections and bed parallel shear. As the lamination thickness decreases tensile failure first begins in the haunch area and progressively extends above the crown until a self-limiting plastic yield zone shape is reach at lamination thicknesses below 0.4 metres. Conclusions drawn from observations at the Niagara Tunnel Project are those of the authors.

May 1, 2009

By James F. Archibald

In historic mining practice, typical thin liner support systems have been considered to comprise non-reinforced or mesh-reinforced shocrete linings. In the early 1990?s, development of alternate forms of liner systems was initiated in Canada which is now undergoing significant international growth in countries which sustain major mining activity. Now internationally designated as thin, spray-on liner systems, a wide spectrum of liner materials, ranging from liquid/liquid to liquid/solid component combinations, has become commercially available. This innovative family of products is characteristically identified as being rapidly deployable, capable of creating ultra-fast setting coverage over rock surfaces, and able to develop tenacious adhesion and pull strength capacities for resisting rock falls and movements. This paper presents a summary of current liner developments and use in principal mining districts world wide. Additionally, a database of material properties for principal product types used in mining and a review of common quality control testing procedures under development are provided. Such information is based upon recent Canadian and international efforts being taken to assess and develop user standards for the implementation of thin, spray-on liners as rock support in mines. This work is intended to continue for a period of years, with the eventual goal being to establish support and installation guidelines for mines based on quantifiable laboratory and field research.

May 1, 2002

By Peter Wells, Laxman M. Amaratuga, Todd M. Kanhai

"Certain mining methods (eg. Cut-and-fill) result in the contamination of run-of-mine ore with shotcrete. This shotcrete remains mixed with the ore throughout processing. Experimentation performed by Falconbridge Limited revealed that underground contamination of ore by shotcrete (eg. as little as 1% by weight) has led to ill-effects on the nickel recoveries from the flotation process in the mill. The nickel recoveries of contaminated samples were lower than tests without the shotcrete Contamination.To optimize flotation circuits it is important to know why the contamination has created these effects and also to find a method to abate or remove them. Laboratory testing showed that the age of the shotcrete was a factor in it’s effect on nickel recoveries. Younger aged shotcrete gave nickel recoveries lower than baseline nickel recoveries with no contamination. Older shotcrete gave nickel recoveries similar to the baseline.Literature on other cementitious material contaminations on ore revealed that a possible means of remediating this problem is the use of acid in the flotation. The initial pH in the flotation pulp was designed to be pH 9.2, but with the young shotcrete contamination the pH was in the neighbourhood of 10.5. Acid addition may act as a means of lowering the pH to the optimal operational value. Laboratory test work showed that acid addition brought nickel recoveries closer to the baseline."

Jan 1, 2000

By O. Mejia, J. Drozdiak

"This paper summarizes a comprehensive energy and cost study comparing an existing SAG mill based circuit at Huckleberry Mine with two proposed circuits involving comminution technologies which are associated with energy efficiency: high pressure grinding rolls (HPGR) and high speed stirred mills. The specific energy requirements expressed as kWh/t for the proposed circuits were determined from pilotscale HPGR and stirred mill testing conducted at the University of British Columbia. Samples and operating data were collected from Huckleberry’s copper-molybdenum concentrator to evaluate current mill performance for comparison. To support the base case, the SABC circuit was modeled using JK SimMet® software. The main comparison focused on the complete energy requirements for each circuit, including materials handling equipment such as conveyors, screens, feeders and pumps. This paper also provides capital and operating cost estimates for each of the comminution circuits. The results showed that the HPGR - ball mill circuit achieved a 21% reduction in energy consumption over the existing SAG - ball mill circuit at the same P80 grind size of 160 µm. At a grind of 80% passing 75 µm, the HPGR - stirred mill circuit showed a 34% reduction in energy compared to the base case. It was concluded that the energy reduction for the new flowsheets significantly improved the economics of the Huckleberry comminution duty.INTRODUCTIONUp until now, tumbling mills such as AG/SAG mills and ball mills have had a dominant bearing on the design and economics of comminution circuits. However, it is commonly agreed that the majority of employed comminution processes are energy intensive and energy inefficient, accounting for up to 80% of overall process plant energy consumption and having an efficiency of as low as 1% (Abouzeid and Fuerstenau, 2009; Fuerstenau and Abouzeid, 2002). The U.S. department of energy reported that there is a potential to reduce energy consumption in the metals industry by up to 61% from current practice to bestestimated practical minimum energy consumption; suggestions included the implementation of best practices and the adoption of energy efficient mining and mineral processing technologies such as advanced blasting techniques, high pressure grinding rolls (HPGR) and stirred mills (U.S. DOE, 2007)."

Jan 1, 2013

By H. E. Urtubia

"BHP-Billiton’s Minera Escondida Limitada, in Chile, is one of the world’s largest copper producers. It treats a combined 10,500 tph of copper ore through its two concentrators: Los Colorados and Laguna Seca. The performance of the rougher circuit at each concentrator was measured and analysed using the JKTech flotation optimisation methodology. This involved developing a flotation model for each concentrator based on cell operating parameters (for example bubble surface area flux and froth recovery) and feed ore floatability characteristics. The rougher circuit performance was evaluated in terms of traditional measures, such as grade and recovery. The operation was also analysed using the measured cell operating parameters and ore floatability and the effect of these with regard to performance (grade / recovery) was assessed.This paper presents a comparison of the rougher circuit at each concentrator in terms of these parameters. The main differences in rougher circuit performance between the two plants were attributed to differences in feed ore floatability characteristics and froth recovery. The comparison highlighted opportunities where performance improvements could be made. The study also showed the usefulness of separating the flotation process into easily measurable subprocesses to further identify the different mechanisms occurring in each rougher circuit. Traditional measures like grade and recovery are useful for monitoring flotation operation but this data lacks the depth to determine the root cause behind operational issues. Determining the operating parameters and ore floatability provides the operating plant metallurgist better tools to assess and manage these issues."

Jan 1, 2006

By Michel Aubertin

Les digues de retenue de résidus miniers devraient être conçues de façon à supporter les charges les plus défavorables qui puissent être anticipées. Les nombreux incidents survenus au cours des dernières années à travers le monde montrent toutefois que la stabilité de ces ouvrages reste encore problématique. Les cas de rupture les plus courants sont reliés aux glissements le long des pentes, à la liquéfaction des rejets, au débordement des bassins, ainsi qu?à l'érosion régressive et de surface. Après avoir rappelé la nature et l?importance des certains incidents récents, l?origine de ces problèmes est brièvement présentée. On aborde ensuite le lien entre les critères à adopter pour la conception des ouvrages et les risques associés à leur rupture. De nouvelles avenues pour aider à contrôler certains problèmes sont enfin discutées, en mettant l?emphase sur la codisposition des roches stériles dans le parc à résidus miniers.

Nov 1, 2002

By A. F. Banks

"Potash processing in Canada commenced on a commercial scale in 1962. Over the last 25 years it has grown into a world-class industry with many advances in processing technology. As it is a relatively young industry, many more advances can be expected. Unlike much of the mineral production in Canada, potash is sold as a range of finished products. The processing involves potash recovery and finishing in about equal amounts in terms of the effort of processing. Environmental concerns are not insignificant and are being treated uniquely in some areas. Research and development efforts, while not carried out on a large scale, are attacking industry problems on a wide front.THE INDUSTRYThe Canadian potash industry has 12 producing mines, 10 in Saskatchewan and 2 in New Brunswick. The total productive capacity of the industry is 18,300,000 tonnes of products per year. At capacity, the industry 1•ill process the equivalent of about 53,000,000 tonnes of ore per year. Plants range in size from 8,000 tonnes to 24,000 tonnes of feed per operating day. In product terms this is from 2,500 to 3,500 tonnes of products per day.Of the 12 mines, 11 are conventional underground mining operations with potash recovery principally by flotation supplemented by crystallization and one is a solution mine where mining is achieved by dissolving the potash and salt in underground caverns and then treating the solution in an evaporator/ crystallizer circuit. In all plants there is commonality of unit operation in the product screening and compaction sections. There are three principal ores being treated in the conventional plants. These may be characterized in general terms as follows:"

Jan 1, 1987