Search Documents

By K. van Netten, T. P. Ernst

"Froth flotation has been used successfully for about a century in the beneficiation of both coal and mineral particles. With the on-going trend towards lower feed grades, however, there is a need to transform this technology in ways that can deliver ultrafast separations, with strong selectivity, and recovery, covering a broader size range. It should be recognised that the hydrophobic effect, with its highly selective and long-range interactions, will most likely underpin any new technology. We identified the separation of the concentrate from the tailings as the rate determining step of conventional flotation technology. This limitation was then addressed by developing a novel flotation technology, insuring the formation of a concentrate that could be separated more rapidly from the tailings. We introduced a novel binder medium, a highly concentrated water in oil emulsion, to act as the focal point for hydrophobic adhesion, effectively replacing the air bubbles used in conventional flotation. The hydrophobic particles adhere to and become embedded within the binder, forming saturated agglomerates that float upwards. Moreover, by forming these large and resilient agglomerates, the product can be quickly dewatered over a screen and separated almost immediately from the tailings. Remarkably, this new binder permits residence times in the order of a few seconds under batch conditions. This paper examines the performance of the technology as a function of the oil wt% added to the slurry. The paper also examines the performance of the technology as a function of the particle size, showing a decline as the particle size exceeds 0.50 mm.INTRODUCTIONFroth flotation involves the collision and adhesion of hydrophobic particles to rising air bubbles, the carrying of those particles from the bubbly-pulp zone into a froth zone, and subsequent drainage and migration of the pulp to achieve the final concentrate (Wills, 2006). Within a Jameson Cell the feed slurry and air bubbles are brought into intense contact within the active area of the downcomer, achieving rapid kinetics of hydrophobic particle adhesion to the air bubbles (Harbort et al., 1994). However, once the bubble laden product and tailings emerge from the downcomer there is the need for separation of the concentrate from the tailings, an inherently slower process. In other devices such as mechanical cells the initial kinetics of particle adhesion are far slower, relying on the turbulent eddies throughout the cell, while in a column the kinetics rely upon an even slower process of bubble interception with suspended and settling particles (Gorain, 2007). However, in all cases the driving force for segregating the bubbles from the tailings, and the drainage of the froth are inherently the same. We do note, however, recent advances by Galvin and co-workers in achieving so-called Fast Flotation, utilizing a system of inclined channels to dramatically increase the segregation rate of bubbles from the tailings, permitting much higher gas and feed fluxes to be applied, achieving up to a ten-fold throughput advantage (Dickinson et al., 2014). Any further improvement within the existing flotation paradigm would require the introduction of centrifugal forces, but this would also require the formation of much finer bubbles than is typically used given the tendency of relatively large bubbles to reach a limiting slip velocity due to deformations and increased drag. Across all flotation devices we argue the rate determining step remains the segregation of the bubbles from the tailings."

Jan 1, 2016

By A. Oja, M. Lahtinen, P. Salonen, B. Saxen

Most of the secondary and low grade zinc raw materials cannot be treated successfully by either conventional roasting - leaching - electrowinning (RLE) process or even by atmospheric direct leaching process. The problems arising especially from high impurity content of these raw materials can be effectively solved by implementation of the solvent extraction process. The utilization of solvent extraction process has been demonstrated by Outotec with raw materials like Waelz oxide, crude zinc oxide and zinc containing concentrator tailings. Based on batch and continuous test work it has been shown that SHG quality zinc can be produced even from the lowest grade raw materials. Impurity control in the solvent extraction process has been examined. The solvent extraction process is the key feature of the whole zinc plant for such raw materials. However, design of the entire zinc process including neutralization and bleed treatment is important for optimization of investment and operation costs of the plant. Very careful evaluation of the zinc process with modern simulation tools is essential. The optimized Outotec zinc process ensures a sustainable and profitable process containing minimal effluent and requiring little residue treatment.

Jan 1, 2014

By U. Erb, L. Monaco

"Electrodeposited nanomaterials are increasingly implemented in advanced industrial applications in the aerospace, automotive, defence, electronic and energy sectors due to their outstanding physical, chemical and mechanical properties, including increased strength and wear resistance, and superb magnetic properties. As with the development of any class of new materials, the corrosion behaviour of these electrodeposits requires considerable attention. This presentation reviews major developments in the understanding of the corrosion behaviour of nanocrystalline metals, alloys and metal-matrix composites over the last 20 years, with emphasis on how their intrinsically high density of intercrystalline defects does not compromise their corrosion resistance as initially expected.INTRODUCTIONOver the past 20 years there have been considerable advances in the understanding of the corrosion behaviour of nanocrystalline metals, alloys and metal-matrix composites. In this paper, the corrosion properties of nanocrystalline nickel, cobalt, zinc, and copper and some of their alloys are reviewed with emphasis on how a reduction in grain size affects their corrosion behaviour in different environments.It is possible to synthesize nanocrystalline material with microstructural refinement down to the range of 1 to 100 nm using a large number of processing methods. There are five basic synthesis methods that can be used to classify the different techniques: vapor-phase processing, liquid-phase processing, solid-phase processing, chemical synthesis, and electrochemical synthesis. Depending on the synthesis method, different microstructures (equiaxed, textured), shapes, and forms (films, particles, bulk material) may be produced. In addition, other factors may be introduced (eg. residual porosity or amorphous phases), aside from microstructural refinement, which can contribute to the observed properties (Erb, 2010). In order to interpret and categorize the resulting microstructures, a dimensional structure modulation scheme was introduced by Siegel (1996) in which zero-dimensional nanomaterials refer to individual particles, clusters, etc. One-dimensionality results from a layered (less than 100 nm thick) structure. Two-dimensional nanomaterials are thin, layered structures containing grains (less than 100 nm) within each layer. Finally, three-dimensional nanomaterials are bulk structures with an average grain size less than 100 nm."

Jan 1, 2012

By Kurt Tischler

This paper presents the field experience of Siemens with regard to Gearless Drives in the mining industry ? We consider the elapsed production hours of Siemens Gearless Drives to be extensive enough to provide a reliable estimation of availability calculated on the basis of data representing repair time, downtime, and operating time. The users of Siemens Gearless Drives confirm an availability of more than 98% after exclusion of some major issues. The paper addresses all of these major issues of Siemens Gearless Drives, describes successfully applied corrective measures, explains the influences on the design of the drives, and lists the downtimes associated with each of these issues.

Jan 1, 2012

By J. -M. Lalancette, D. Lemieux, C. Chouinard

"A gold bearing concentrate containing 107 g/T of gold, 9.3% copper and 706 ppm of mercury was processed at the demonstration scale for the extraction of gold and copper using a cyanide free process. The concentrate was generated through flotation to upgrade the gold and copper grade, but also showed contamination with mercury. This concentrate was submitted to the DST process demonstration plant. The concentrate was first oxidized using a fluidized bed to produce a calcine. The mercury was volatilized during the oxidation stage with an efficiency higher than 98%. The mercury was condensed and removed from the sulfuric acid using a thiosulphate process. Copper was extracted from the calcine as copper sulphate using diluted sulfuric acid. The solid remaining after acid leaching was submitted to the DST chlorination process for gold extraction. Under optimized conditions, a gold extraction of 97.3% was achieved in the chlorination reactor. Gold was recovered from the pregnant brine by precipitation on silica using a DST proprietary process.INTRODUCTION Dundee Sustainable Technologies Inc. (DST) offers proprietary metallurgical processes for the treatment of material from the mining industry. DST processes enable the extraction of precious metals and for the removal and stabilization of contaminants, such as arsenic, from ores and concentrates. DST provides environmentally-friendly, viable and efficient processes, capable of handling complex and refractory ores which cannot be processed with conventional approaches due to metallurgical issues or environmental considerations. Several mining jurisdictions around the world have banned or restricted the use of cyanide. DST has developed a closed loop chlorination process as an alternative to the conventional cyanidation process for the extraction of precious metals from minerals. The tailings from the process are inert from toxic substances such as cyanide and organic compounds, are sulphide depleted which means they do not generate acid, and thus, meet and/or exceed environmental norms. The process has demonstrated excellent gold recoveries within a fraction of the time needed for cyanidation to obtain similar results. Moreover, the closed loop process does not generate any liquid effluent and does not consume much water: it only requires a water make-up to compensate for moisture leaving with the tailings and by-products, and seawater may be used. The improved environmental footprint of the DST process has been certified by the Environment Technology Validation program (ETV) which provides an independent evaluation of the performance claims of innovative technologies."

Jan 1, 2017

By T. Joseph, E. Zheng, M. Curley

"Hydraulic transportation efficiency and production optimization are considerations in the surface extraction of Athabasca oil sand deposits. To reduce the dependence on haul trucks, it is possible to extend the hydraulic transport system to production faces using a mobile at-face slurry system (AFSS). The flexible arrangement of connected pipelines transports slurried minerals from the mining face to the processing plant. An experimentally verified mathematical model indicates the friction loss of oil sand slurry associated with the AFSS. Laboratory-scale testing enables extended analyses for examining pipeline slurry transport in an oil sands environment.RÉSUMÉ L’optimisation de l’efficacité du transport hydraulique et de la production sont des considérations importantes dans le domaine de l’exploitation à ciel ouvert des gisements de sables bitumineux de l’Athabasca. Afin de réduire la dépendance envers les camions de transport, on envisage d’étendre le système de transport hydraulique aux fronts de taille à l’aide d’un système mobile de transport des matériaux sous forme de boue à partir du front de taille (AFSS, de l’anglais at-face slurry system). L’organisation flexible des conduites reliées permet le transport de minéraux à l’état de boue du front d’exploitation jusqu’à l’usine de traitement. Un modèle mathématique vérifié de manière expérimentale indique la perte de charge par frottement des schlamms provenant du traitement des sables bitumineux associée à l’utilisation de l’AFSS. Des essais en laboratoire permettent de mener des analyses approfondies portant sur le transport de boues dans des conduites dans un environnement de sables bitumineux. INTRODUCTIONObjectives and scope of studyThe at-face slurry system (AFSS) concept has become a competitive means for materials handling to optimize haulage system efficiency and cost. The mobile and flexible arrangement of the AFSS introduces a unique set of hydraulic transport problems. This paper will focus on developing the mathematical models governing the friction and head losses within the AFSS concept.Background of the problemLarge-capacity shovels and dump trucks are increasingly used for excavation, loading, and hauling in the operation of surface mining. Production cost and efficiency optimization are demanded during the Athabasca oil sands (Alberta, Canada) mining process to secure North America’s energy supply. Increasing haulage distances, rugged terrain, and a constrained mine environment are conditions that will reduce the effectiveness of the shovel-truck haulage system (Frimpong, Szymanski, & Changirwa, 2003). In such conditions, the tire heat index and weight, distance, and time limits for truck haulage can be exceeded, simultaneously creating extreme tire wear and high maintenance costs. In addition to low production cost and equipment effectiveness, a mining environment also requires efficient waste-material recycling and distribution. Waste materials need to be recycled from the processing plant to a new destination such as a tailings dam, or replaced in mined-out areas such as backfill. The Athabasca oil sands configuration and location characteristics result in a mining environment that would benefit from flexible pipelines for constant production and an efficient waste-material recycling process."

Jan 1, 2017

By G. M. Castillo

Newmont?s Phoenix mine started production in March of 2006. Due to the extreme hardness of the ore, the mill has struggled to meet throughput projections. Grinding studies showed that optimizing the existing circuit would not achieve budgeted throughput. These studies also showed that the pebble crusher was being underutilized due to the inability of the SAG mill to break the rock. The concept was developed to supplement the feed to the existing pebble crusher with a secondary crusher. Models of this process looked favorable so a portable crusher was installed to test the process. The temporary crusher was successful at increasing the throughput by 7% and based on the operating data, plans are currently being developed to install a permanent secondary crushing system in front of the SAG mill. This paper will review the results from the test crusher and the flow sheet for the permanent secondary crusher.

Jan 1, 2012

By John Galbraith, Dwayne D. Tannant, Chris C. Langille

"Development of underground openings in a deep mining environment requires a support system that is able to absorb energy as a result of dynamic loading due to rockbursting and blasting and static loading due to convergence as the development face advances. The support system must be resistant to corrosion and be effective over the life of the excavation, upward of ten years, yet simple and cost effective to install. Over the past two years, research has been conducted at INCO’s Creighton Mine to try and identify a one-pass grouted support system that will meet these needs.The main problem faced, with simply using grouted rebar at depth, is the effect of tunnel convergence on the stiff grouted bolts. Typically, if fully grouted, stiff rebar are installed to the face of an advancing development heading, the amount of convergence that occurs can result in failure of the bolts at the face plates used to attach the mine screen to the back. An initial support is required to enable crews to continue the bolting cycle in the immediate term, yet allow for this convergence over the longer term as the drift advances. The ideal support system will allow both to occur, giving effective immediate support while providing long-term effectiveness in allowing convergence to occur while maintaining the capacity of the bolt.This paper will investigate the expected convergence in deep development headings at +2200 m (+7200 ft) through the use of direct measurements using both flex rod extensometers grouted into the back of a development heading and five-point tape extensometer stations. Measured results will be compared with simple2-D numerical analysis to evaluate the anticipated convergence expected to be absorbed by the bolting system. The required convergence will then be compared with load deformation response of several support configurations."

Jan 1, 1996

By Fadi Layyous Gedeon, David Hatton, Solomon Mogashoa, Tuhin Banerjee, Faisal Aljohani

The adoption of innovative technologies in mineral processing often raises concerns about complexity and integration. However, Woodgrove’s Direct Flotation Reactor (DFR) technology at Barrick’s Jabal Sayid copper concentrator provides a different perspective. This paper outlines the smooth integration of DFR technology from piloting to full-scale commissioning, showcasing how easily the cells were brought online. Installed in a cleaner scalper role, DFR cells at Jabal Sayid upgrade re-ground rougher concentrate to final concentrate in one stage. Despite processing challenging ore, the DFR cells delivered concentrate grades that consistently exceeded expectations. The commissioning process was straightforward with minimal hurdles, highlighting the technology's user-friendly nature. This paper advocates for a shift in perceptions about new technologies in mineral processing. The success of DFR technology at Jabal Sayid demonstrates that “different” doesn’t mean “difficult.” By focusing on ease of commissioning and operational integration, innovative solutions can enhance processes, improving efficiency and productivity in the mining industry.

May 4, 2025

By Ltd Changsha Research Institute of Mining and Metallurgy Co., Shi Yunliang, Luo Yunbo, Chen Jun, Liu Miaohua, Xiao Jinxiong, Long Yan

"A refractory lead-zinc oxide ore located in Yunnan has hundreds of tons of metal reserves, which is hard to be recovered effectively by conventional oxide ore beneficiation methods. In this study, by sulfidation roasting of raw-ore, sulfide deposit is formed on the surface of the lead-zinc oxide ore, and then the roasted ore is processed with bulk flotation. The test results indicate that a bulk concentrate with grade of 7.85% lead and 34.24% zinc, recovery of 79.13% lead and 79.04% zinc, respectively, can be obtained by using conventional sulfide ore flotation method.The sulfidation process shows that pyrite in the raw ore releases S firstly, then S reacts with PbO and ZnO to transform into PbS and ZnS. When the mole ratio of sulphur:zinc is 0.59, the surface of smithsonite is covered with a layer of zinc sulfide. When the mole ratio of sulfu:zinc rate is 1.47, entire simthsonite particle is transformed into zinc sulphide. Thus the transformed particles can be recovered by flotation without complete sulfidation.INTRODUCTIONWith the increasing demand for zinc and decreasing of zinc resources, people pay more attention on development and utilization of zinc oxide ore. However, zinc oxide ore has wide range mineral kinds, complex mineral composition, disseminated fine-grained particle size, and high content soluble salt, so current study results about the zinc oxide ore with conventional flotation are not satisfactory. So far, process dealing with zinc oxide ore includes: sulfuration (Na2S)-flotation, direct flotation with fatty acids collectors, metallurgical methods, in which sulfuration flotation is the most widely used method. The basic principle of sulfuration flotation method is firstly roasting oxide ore with vulcanizing agent, and then recovering the sulfurated oxide ore with flotation, which is similar with recovering nature sulfide ore by using conventional collectors such as amines and xanthate."

Jan 1, 2016

By N. Chow, W. McCombe, G. Remple, J. Nikkari, L. Nightingale-Mercer

Orano Canada Inc. (Orano) operates the McClean Lake mill in northern Saskatchewan, processing high concentration uranium ore, delivered in slurry form, from the Cameco operated Cigar Lake mine. This slurry is ultimately processed into the purified uranium oxide product known as calcined yellowcake. During the calcining process, sulphate (SO42-) entrained in the yellowcake undergoes thermal decomposition into sulphur dioxide (SO2). SO2 is a colourless gas that poses health and safety risks. Since 2016, an anhydrous ammonia dosing system was successfully added to the existing Venturi particulate scrubber system to provide efficient removal of SO2 from the calciner off-gas. Within the pH controlled scrubber solution, SO2 exists in a pH dependent equilibrium with sulphite/bisulphite (SO32-/ HSO3-). The presence of a significant fraction of reduced sulphite and bisulphite in mill solutions presents a hazard in downstream circuits. Should these solutions drop in pH, either through natural oxidation or inadvertent mixing with low pH solutions, the solution equilibrium will shift from SO32-/HSO3- in favour of SO2, resulting in the evolution of SO2 gas from any liquid surfaces. In 2018, Hatch Ltd. (Hatch) and Orano implemented a design change in the calciner scrubber system. Blowdown from this system is now treated in an oxidation pre-step utilizing hydrogen peroxide (H2O2) and anhydrous ammonia (NH3) for pH control, in order to convert the residual sulphite/bisulphite present in solution to stable ammonium sulphate product. This paper will detail some of the challenges and actions undertaken to minimize SO2 risk, culminating in the recent introduction of a novel system designed to oxidize sulphite/bisulphite and prevent mobilization from the calciner scrubber solution into other mill areas where there is the potential for acidification and SO2 release.

Jan 1, 2020

By K. Sakai, M. Miyaue, T. Aoki, T. Tani, S. Tanaka, N. Kudo

In the planning stage of a tunnel, due to limited technology in the geological survey and the financial restriction, tunnel supports are often designed from unsatisfactory information, and the tunnel construction is started. Therefore, "Information-oriented construction" is carried out in the construction stage, in which the design is rationally verified and modified by observations/measurements. Moreover, the ground conditions ahead of a tunnel face must be predicted for efficient and safe tunnel construction. The authors have examined effective prediction methods to the ground conditions ahead of a tunnel face under construction of mountain tunnels (Aoki et al., 2010) in view of the established method (Schubert et al., 1995). Though the prediction method of Schubert requires the displacement in the direction of tunnel axis, it is difficult to obtain its accurate data by the electronic distance meter. Then, we have proposed a method that uses tilt sensors installed at the tunnel crown near the face to obtain the slight tilting information. To measure inclination of the tunnel crown, this inclinometer was originally developed as a daily control measurement, such that the geological condition and its possible change behind the face could be detected early, and a steady advance and construction safety could be ensured. This paper describes the method of forward prediction mechanism and advantages of this suggested method. It then presents the typical results of a field verification test at a tunnel under construction and an example of evaluation of the ground conditions ahead of the face based on the 3D numerical analysis in three types of condition changes of ground deformation moduli.

Jan 1, 2015

By G. Shore

"The development of a DC resistivity instrumentation system for data acquisition in extreme topography yielded an unexpected bonus in the quality and information content of the type of raw data gathered. Not only were traditionally too-rough areas being investigated systematically for the first time, the unique high-density, multi-directional raw data were providing the opportunity to greatly expand the range of conductive and resistive signatures that could be accurately recognized. Using a true 3-D inversion algorithm, 3-D earth resistivity imagery began to show distinctive anomaly patterns for hydrothermal mineralization at the seldom-visited resistive end of the spectrum, successfully imaging epithermal gold systems in conditions that had defied conventional ground and airborne geophysics for years.The traditional mode of designing a resistivity survey to test a specific target concept was shown to be an unnecessary limitation on exploration thinking when a single sweep acquisition of dense, multi-directional 3-D raw data could effectively provide the all-targets “shotgun” coverage that would take 10 or 12 conventional surveys to duplicate. Exploration planning has the opportunity to move from single steps of trial and error geophysical testing to a mode of mapping everything at the outset, and then sorting out what might be of exploration interest in the results. Survey parameterization becomes the non-technical process of marking an outline on a map and declaring “survey here.” Operational and interpretational reasons for not testing where the exploration interest lies have all but disappeared. With any-terrain capabilities and unprecedented raw data density and overlap to support interpretation of complex conditions, that outline can be drawn through extreme rough terrain, including lakes, cliffs, industrial facilities, and grounded installations to test for generally unknown sub-surface features of potential interest.As more is learned about the larger-scale signatures of ore settings and the district-scale geo-electric imprint of hydrothermal processes on lithology, it appears that the only thing certain about ore signatures is their uncertainty. This is not bad news. New opportunities abound as the advanced 3-D technology allows a first effective look at the previously unexplorable rough terrain or complicated settings, and a second look at areas where older results may now be known to be non-definitive."

Jan 1, 2002

By Farzad Mohammadi, David Kratochvil, Patrick Littlejohn

"With more rigorous regulations being enacted in the mining industry, a need exists for cost effective and environmentally compliant technologies to remove selenium from mine impacted waters to ultra-low concentrations. Existing selenium treatment methods have high life cycle costs, introduce risks of acute fish toxicity, and produce biological waste residues that represent future liabilities. Furthermore, achieving selenium discharge limits of less than 4 ppb is a challenge for existing technologies. Selen-IX™ is a technology developed by BioteQ that selectively removes selenium from mine impacted waters to less than 1 ppb. The technology is purely physico-chemical and takes advantage of the basic principles of ion exchange and electrochemistry. Unlike conventional electrocoagulation that removes suspended solids and breaks emulsions or oxidizes heavy metals, the electrochemical process employed by Selen-IX™ relies on creating conditions where iron acts as a highly effective reducing reagent transforming selenium from a dissolved species into elemental selenium bound in a solid phase. The iron-selenium by-product of Selen-IX™ is an inorganic, non-hazardous and chemically stable solid. Due to their high iron content, the solids produced by Selen-IX™ are of interest to the steel making industry as a low cost feedstock. This offtake potential can not only reduce the life cycle cost of selenium removal by reducing disposal costs but more importantly, eliminate the risk of future environmental liabilities. In this paper, the basics of Selen-IX™ technology are presented along with results of successful piloting on streams from coal and copper-gold deposits.INTRODUCTIONVarious contaminants are released into mining wastewater during the extraction and processing of metals. One such contaminant is selenium. A naturally occurring element found in rocks and minerals, mining activities accelerate its release into the environment. Selenium in trace quantities is essential to all life forms but at higher concentrations it can be harmful, especially to aquatic life where selenium bioaccumulation can lead to reproductive deficiencies."

Jan 1, 2016

By Linlin Zhang

Rare earth elements (REEs) are a group of lanthanides elements which have been widely used in the electronic, petrochemistry, metallurgy, and defense industries. Their demand has increased sharply in the past decade with the boom in electronic device production. Some countries now consider them strategic metals for the future and it has been forecasted that REEs may become a dominant contributor to global economy. In the wake of REE exploration, mining and processing, concern has grown over occupational and community health issues and risks. A portion of available literature on this topic however is written in the Chinese language, and thus research information related to health and REE mining is not readily accessible to mineral development planners in countries such as Canada, where REE mining is now evolving. As REEs also represent an important commodity, primarily stemming from Chinese production, it is important to begin to understand the potential health costs related to this mining sector. There are two main objectives of this paper. The first is to present an overview of REE mining with a focus on geological characteristics, global production and uses with particular attention to the main producer: China. The second is to present the results of a literature review (using both Chinese and English sources) on REE mining and health and identifies key occupational and community health issues that require consideration. This paper concludes by identifying some critical issues this sector needs to address to ensure the sustainable development of this mining activity.

Aug 1, 2013

By S. Usui, Y. Shinohara, C. Tokoro, K. Horiuchi, S. Owada

Process optimization of heating and physical separation for Cobalt (Co) recycling from spent lithium ion battery (LIB) was investigated. LiCoO2 in spent LIB was transformed to LixCoO2 which was more easily decomposed than LiCoO2 by heating. Coexisting materials of aluminum and carbon, and sealed atmosphere of the LIB promoted LixCoO2 decomposition. In an atmosphere of Argon, 95 % of LixCoO2 in the spent LIB was decomposed to 76 % of Co oxide and 19 % of Co metal in 10 min at 823 K; a lower temperature than the theoretical value for LiCoO2. The Co oxide and Co metal exhibited magnetic properties and could be recovered by wet magnetic separation. Furthermore, slow heating was effective for grain growth of Co oxide and Co metal. At 2 K/min rate of heating, average grain size of Co oxide and Co metal were 239 µm and 28 µm respectively, whereas at 30 K/min they were 190 µm and 15 µm respectively. Therefore, separation efficiency for Co recovery by wet magnetic separation was increased when spent LIB was slowly heated at 2 K/min.

Jan 1, 2015

By Y. Thibault, L. Morin, R. Cameron, D. Gould

"There are an estimated 50 to 100 million dry metric tonnes of low-grade nickeliferous pyrrhotite tailings in the Sudbury area alone, with an average nickel grade ~0.8% (plus cobalt). Pyrrhotite is a highly reactive sulphide mineral that has the potential to generate acidity; consequently, it is stored in large tailings ponds that require perpetual treatment to avoid the production of acidic drainage. Re-processing this material using bioleaching technologies has the potential to recover valuable metals, while reducing the toxicity, reactivity, and acid generating potential of the remaining residues. CanmetMINING is currently developing a stirred-tank bioleaching process to recovery nickel and cobalt from pyrrhotite-rich tailings. Stirred-tank experiments have been conducted with one tailings sample over a range of pH and temperature conditions, resulting in 80 to 90% and 70 to 80% leaching of nickel and cobalt respectively in 10 days.INTRODUCTION Sulphide tailings may represent a significant financial liability for mining companies as these wastes may produce acidic drainage under some disposal conditions. As a result, the companies must post financial bonds large enough to ensure there are sufficient funds for perpetual management of these wastes. At the same time, there are billions of dollars in metals incorporated into these mining wastes waiting to become valorized. Many sulphide tailings are amendable to bacterial oxidation for metal extraction. Re-processing of tailings using bacterial leaching has the potential to recover valuable metals from waste; and reduce the toxicity, the reactivity, and the acid generating potential of the remaining residue. By reprocessing these wastes there is an opportunity to significantly reduce liabilities and financial assurance bonds, while recovering metal values. There are an estimated 50 to 100 million dry metric tonnes of low-grade nickeliferous pyrrhotite-rich tailings in the Sudbury area alone with an average nickel grade ~0.8% (Peek et al., 2011) plus cobalt and copper. Pyrrhotite is separated from pentlandite concentrates by magnetic separation and flotation. It is already finely ground and has often been segregated from other tailings material, making „mining? relatively inexpensive. This represents roughly (> $100/ton) in contained value, with negligible mining costs. This paper reports on the development of a stirred-tank bioleaching process for recovering nickel and cobalt from pyrrhoitite-rich tailings, which is currently underway at Canmet MINING."

Jan 1, 2017

By Sudarshan Martins

The measurement of acoustic signals produced by a tumbling mill has been previously used to determine the operating state of the mill and correlate the variations of the sound intensity with the operating conditions of the mill. Separately, the discrete element model (DEM), a software simulation of the mill, was developed to provide insight into the operation of the mill. Presently, there has not been much work reconciling the DEM simulation of the mill with the acoustic signal. Working from basic principles of linear, time-invariant systems, agreement between an acoustic DEM simulation and the measured signal is sought. First, the impulse response function of the mill is measured. The DEM provides the forces applied to the mill shell as a function of time. A convolution of these simulated shell forces and the transfer function gives the simulated acoustic signal. This signal is compared to the measured acoustic signal, both in the time domain and the frequency domain. Finally, a discussion of the results is given.

Jan 1, 2012

By R. Hammen, J. Lifton

"The purification of rare earth elements (REE) at mining operations is traditionally accomplished by multiple chemical phase-transfer processes including precipitation, solvent extraction, and ion exchange. We describe REE purification results with Solid Phase Extraction (SPE) columns that were developed to improve the speed and economy of REE purification. The SPE columns have the properties of enhanced equilibration kinetics, so that residence time of a few seconds will accomplish selective chemical transfers from solution phase to solid phase. We describe the separation of REE’s as a class from leach solutions and the further purification of REE salts. INTRODUCTIONHistorically the rare earths were first chemically separated from each other and purified by fractional crystallization. This slow, cumbersome, and laborious process was not suited to commercial production. Solvent Exchange (SX) technology was applied to the problem of separating and purifying the rare earth elements when it was determined in the late 1960s that there might be commercial uses for them individually. At the same time the very slow and expensive technique of ion exchange was applied either for ultra-purification of the desired “light” rare earths, or for the recovery and purification of the tiny amounts of higher atomic numbered, “heavy,” rare earths. Solvent Exchange (SX) has today become the standard for separating the rare earths across their atomic number spectrum. Whereas the separation of the light rare earths commercially may take 30 “cascades’ in a modern Chinese plant, the total separation of all of them from each other may take up to 80 such “cascades,” and is only even “practical’ with preconcentrated feed stocks, such as those produced in China by heap-leaching techniques performed in situ on very low grade radio-nuclide free ionic absorption clays.. Ultra-pure materials of all types are produced today by ion-exchange processing of ionic species already separated by solvent exchange.Hard rock deposits and refractory residues of tin mining and residues from uranium mining have been identified outside of China with very high ratios of dysprosium and other heavy rare earths to the majority lighter ones. Several issues face those who wish to process these materials so as to separate the heavy rare earths commercially:"

Jan 1, 2012

By J. Janzen

The cost to supply ventilation may exceed 40% of the total mine energy cost for underground mines and is often higher for deeper mines. The goal of Ventilation-on-Demand (VOD) is to ensure that the required quantity and quality of air is supplied to underground mining crews and diesel equipment at the least energy expenditure (minimum cost). A VOD system may include control of surface fans (Supply & Exhaust), underground booster fans, auxiliary fans and automated regulators/dampers to regulate the flow of air with more control elements providing more value. Strategically located Air monitoring stations measure air quantity and quality and provide feed-back enabling control. The modular design involving controls, intelligent instrument and intelligent motor control centres coupled with a communication network allows the quick installation, commissioning and expansion of the system as the mine develops. The result is a very robust, flexible system while reducing maintenance costs and spare parts. This paper discusses the impact of sensors, installation and commissioning on advanced controls and provides solutions for in-field applications.

Aug 1, 2013