Search Documents

By W. S. Szolga, M. Moser, M. D. Soderstrom, L. Cohen

"CYANEX® 272 is a phosphinic acid-based solvent extraction reagent used commercially since the early 80’s to recover and purify cobalt from sulfate solutions. Historically, the design of CYANEX 272 circuits has involved the selection of an optimal pH profile during pilot-scale testing using mixbox pH control. The desired pH profile is required to be carefully controlled in the same manner during commercial operation. To assist operators in the design and optimization of their circuits, Solvay developed CYANEX 272-specific solvent extraction modeling software, which has enabled determination of the ideal pH profile and staging configuration. Solvay’s recent advances in modeling capabilities have allowed the simulation of circuits without direct mixbox pH control. Modeling has indicated that circuits operated without direct pH control can achieve the desired metal separation while simplifying the commercial operation significantly. This paper reviews a number of potential circuit configurations for the use of CYANEX 272 and demonstrates the separations achievable under the right design and operational conditions, some of which have historically been considered too difficult.INTRODUCTION CYANEX® 272 is a phosphinic-acid based reagent designed specifically for the separation of cobalt from nickel by solvent extraction from weakly acidic sulfate solutions (Rickelton, Robertson, & Burley, 1982; Rickelton, Flett, & West, 1984; Rickelton & Nucciarone, 1997). Following commercial introduction in the 1980’s, CYANEX 272 has been used in a number of hydrometallurgical flowsheets for cobalt purification and/or recovery. CYANEX 272 metal extraction occurs by means of a cation exchange mechanism. Extraction of a divalent metal ion M2+ is represented by the following equation where RH represents the CYANEX 272 ligand and MR2 represents the ligand-metal complex."

Jan 1, 2017

By A. Warczok

Smelting slags contain payable metals in a dissolved form and as mechanically entrained matte or metallic inclusions in the size range from 2 to 1000 µm. Slag cleaning requires reduction of magnetite and metal oxides and sedimentation of inclusions. Slag cleaning in an electric furnace is carried out in batch or semi-continuous mode. The strong trend for continuous slag cleaning generates the basic question about the optimal geometry of the electric furnace. Results of combined CFD, potential distribution and heat transfer modeling allowed for the determination of the fluid flow pattern and the temperature distribution in a classical, circular electric furnace as well as in a rectangular furnace. For the rectangular furnace, various length/width ratios and position of electrodes have been simulated. Analysis of key phenomena pointed out the advantages of the rectangular electric furnace over the circular furnace, particularly for continuous slag cleaning. Phenomena that have been analyzed were mass transfer, the rate of slag reduction, coalescence and settling of inclusions, all on the basis of the calculated slag flow pattern and the temperature distribution.

Jan 1, 2007

By J. A. Drozdiak, W. Tse, P. P. Rosario

"In a recent publication (SAG 2015), we presented a non-conventional high pressure grinding roll (HPGR)-ball mill circuit as a lower capital cost alternative to the “standard” HPGR circuit. The circuit was designed for the treatment of a hard ore and relatively high tonnage (50,000 t/d). That paper provided details such as flowsheets, layouts, and equipment lists for the two options and compared their calculated capital costs demonstrating significant savings for the proposed circuit. This paper extends the analysis to a third option, a traditional semi-autogenous ball crushing circuit, giving the same level of details and now including the operating cost estimates for all three options for a more comprehensive analysis. Moreover, this work also provides information about the strengths and weaknesses of the non-conventional HPGR circuit when compared to the “standard” HPGR option.This study demonstrates that the proposed non-conventional HPGR-based circuit not only provides a lower overall capital costs for the project if compared to a “standard” HPGR circuit but also brings the capital cost to the level of the traditional semi-autogenous grinding (SAG)-ball mill circuits. In addition, the innovative HPGR circuit provides similar operational cost savings of the “standard” HPGR and thus a significant advantage when compared to the SAG option. With the current capital cost sensitivity for most greenfield projects, the proposed alternative circuit should help make HPGR-based circuits more competitive and thus promote the utilization of a technology that enables higher energy efficiency and reduced greenhouse gas emissions. INTRODUCTIONThe application of high pressure grinding roll (HPGR) technology in comminution circuits is well established for the processing of cement, diamonds and iron ore (Broeckmann & Gardula, 2005), and over the past 10–15 years, this technology has slowly been applied to hard ores in high-tonnage precious and base metal operations. Unfortunately, under the current economic climate, the ability to finance large capital projects has become very difficult and companies tend to have an easier time securing funding if the capital expenditures (CAPEX) are low with a proven process method. The traditional semi-autogenous grinding (SAG) mill / ball mill circuits easily fit into this mould, having been installed in countless plants around the world over the past 30 years with relatively low capital requirements. In contrast, it has been well-documented that HPGR-based circuits are capital intensive with complex material handling systems (Seidel, Logan, LeVier, & Veillette, 2006). Although these circuits benefit from reduced operating costs with the increase in energy efficiency and the elimination of steel grinding media (Rosario, Boyd, & Grundy, 2009), if the company is unable to secure financing to build the plant, these advantages remain out of reach. With the current trend to retrofit existing SAG circuits with a secondary crushing circuit to achieve design throughput, the opportunity to circumvent this gross inefficiency by making HPGR-based circuits more capital friendly would greatly benefit the industry."

Jan 1, 2016

By BARRY BANNATYNE

Non-swelling bentonite has been quarried in Manitoba by Pembina Mountain Clays Limited since 1941. It occurs in several thin layers near the base of the Pembina Member of the Upper Cretaceous Vermilion River Formation, and is quarried from the narrow outcrop belt along the slope of the Manitoba Escarpment. It is marketed both as natural and activated bentonite for a variety of specialized uses. Percolation of acidic water through bentonite has produced a naturally activated bentonite with good absorbent properties; these properties are enhanced by treatment with sulphuric acid to produce an activated bentonitefor decolourizing petroleum and vegetable oil.

Jan 1, 1984

By B. McKevitt, P. Abbasi

The ion exchange process (IX) is applied in the mining industry for the removal of impurities from process streams, treatment of waste solutions prior to disposal and the recovery of valuable metals. Extensive studies have been performed with the goal of modeling of IX for the case of a single metal loading onto iminodiacetic resin in the hydrogen form. However, in a real system, a resin may be saturated by impurities (iron, calcium, magnesium, manganese), which are then displaced by the metal of interest. The present study provides an insight into the Fe2+ loading process onto iminodiacetic ion exchange resin under the infinite solution volume condition. The study involves the measurement of iron loading under a variety of experimental conditions as well as an attempt to model the loading process using the hybrid correlation advanced by McKevitt (2012). The importance of the experimental and modeling work are discussed in the context of resin in pulp recovery of nickel.

Jan 1, 2014

By D. Larouche, M. Mardan

Hot tearing is a complex defect in aluminium castings which is produced during solidification when a certain amount of liquid phase remains and weakens tensile resistance of the alloy. In direct chill casting of aluminium alloys, hot tears initiate at the surface of sheet ingots just after the primary cooling zone, where the microstructure is particularly vulnerable. In order to study the hot tearing susceptibility of these alloys, and the effect of grain refiners on their thermo-mechanical behavior , tensile tests were carried out in the semi-solid state ( ~95% solid) and at low strain rates using an apparatus called DCSS, for Direct Chill Surface Simulator. This apparatus, originally developed at Alcan Arvida R&D Centre (ARDC), is an instrumented rig test reproducing the conditions prevailing during the primary cooling stage of the DC casting process. The mechanical behavior of solidifying shells and the hot tear formation under applied tensile loads were measured and the occurrence of hot tearing was observed. Temperature in different locations of the casting, applied load and surface strain were monitored during the tensile tests conducted on aluminum alloys AA5182, AA6111 and AA3104. The microstructure of the tested samples was examined using the optical microscope to evaluate their columnar or equiaxed aspect and their effect on the mechanical response of the alloy. A special emphasis has been given to the evaluation of fractions solid existing in the castings at the start of the tensile tests, taking into account the local temperature, thermal gradient and cooling rates experienced. It was found that excessive grain refiner additions decreased the strength of solidifying shells because of the increased level of porosity induced by easier nucleation of new phases (gas included). It was also observed that cooling rates increased with the level of grain refiner, a phenomenon that was associated to the higher number of contact points obtained with small equiaxed grains. Finally, the concept of a stress based criterion for hot tearing was reinforced by the strengths obtained on not grain refined AA5182 and AA6111 showing similar fraction solid near the surface, but significantly different grain sizes.

Jan 1, 2006

By R. Hagiwara, S. Kobayashi, K. Yasuda, T. Nohira, K. Kondo

To establish a process for the electrochemical recovery of rare earth elements from used magnet scraps, the electrochemical formation of RE-Ni alloys in molten NaCl-KCl-RECl3 salt at 973 K was investigated. Cyclic voltammetry and open-circuit potentiometry indicated the formation of several phases of RE-Ni alloys. The formation potential for each RE-Ni alloy phase was determined from the results of scanning electron microscopy and X-ray diffraction of alloy samples prepared by potentiostatic electrolysis of a Ni plate electrode at various potentials. The optimum electrolysis conditions for the separation of Nd, Dy, and Pr are discussed.

Jan 1, 2014

By M. Connell, S. Bedrossian

Alkali cracking followed by chloride-based leaching is one of the prominent methods for rare earth element processing. Regeneration of the leach lixiviant, namely hydrochloric acid, is a critical operation in the process. A number of different process routes are available for recovery of hydrochloric acid from chloride solutions. The objective of this paper is to discuss various recovery routes and analyze the impact of several input variables on the variable operating cost.

Jan 1, 2014

By Diego L. Romero, Joy P. Romero

"IntroductionMinerals may be classed broadly as ferromagnetic (magnetite for example), as paramagnetic (attracts to regions of magnetic field convergence) and as diamagnetic (attracts to regions of magnetic field divergence). High-intensity separators are not necessary to separate ferromagnetic minerals from other classes. Rather, low-intensity units that generate fields below 5000 gauss are adequate for this purpose. However, paramagnetic minerals, such as ilmenite, with high magnetic ""attractability"" require fields of up to 10 000 gauss; those with low attractability may require even higher fields. Table 1 shows approximate ranges of field intensities necessary to separate ferromagnetic and paramagnetic minerals from minerals of lower attractability, along with the force with which they are attracted relative to iron in a standardized magnetic field.Uniform magnetic fields, not useful for separators, are generated between flat parallel surfaces; non-uniform fields, useful for separators, arise when at least one of the surfaces is of irregular shape. The diagrams below show how magnetic lines of force align relative to north and south poles.If a particle is placed in a uniform field, it feels no displacing force unless the particle distorts the applied field assymmetrically. This is not the case in non-uniform fields which are required for magnetic separators.Magnetic fields can be generated by permanent magnets (low intensity), by electromagnets (medium and high intensity) and even by superconducting coils (100 000 gauss fields and higher), although the latter are not as yet useful in production environments .The magnetic force of attraction per unit of mass, that acts on a paramagnetic mineral such as hematite, increases in proportion to the strength of the field . Unfortunately, the highest fields attainable with electromagnets is of the order of 20 000 gauss. Fortunately, the gradient of the fie ld (that is, the degree of convergence of magnetic lines of force) is important, because the attractive force per unit mass is proportional to it also . This can be stated:"

Jan 1, 1989

By R. G. Bradburn

"Brenda Mines Limited is a low grade open pit mining and milling operation located near Peachland, British Columbia. The mill was brought into production in late 1969 at a rated capacity of 24,000 tons per day. Tt currently treats an average of 30,000 tons per day of an ore that has an average grade of 0.130% copper and 0.030% molybdenum.Description of Crushing and Grinding CircuitsRun of mine ore is delivered to a primary gyratory crusher. The minus seven inch product is separated into plus and minus one inch fractions on two parallel vibrating screens. The fine product is conveyed directly to the mill fine ore bins, while the coarse fraction is sent to a 45,000 ton stockpile.Material from the stockpile is fed to two standard cone crushers which operate in an open circuit with five secondary vibrating screens. The minus five-eighth inch product from these screens is conveyed to the mill fine ore bins while the coarse fraction is fed to four shorthead cone crushers. These crushers operate in closed circuit with the screens."

Jan 1, 1981

By T. Macpherson

ABSTRACT: Drawing on past research experience with sprayable polymer mine support agents (TSLs), Spray On Plastics Ltd. has developed a TSL ground support system called RockWeb. Using a relatively new polyurea polymer technology, RockWeb has been engineered to solve problems encountered underground with polyurethane liners by incorporating rapid curing, moisture insensitivity and superior physical performance. RockWeb possesses a unique, patented ability to be sprayed in a ?cobweb? like consistency allowing the applicator to span fissures in the rock, ensuring no initial defects in the liner, and maintaining design thickness over highly irregular surfaces. This ability, coupled with the high strength and elasticity of polyurea, allows RockWeb to mitigate rock movement through yielding, while maintaining intimate surface confinement. RockWeb provides reduction in logistics through the transport of 1/25 of the material quantities required for shotcrete, rapid deployment rates of as little as 30 minutes per round, and immediate return to the work area. This paper will discuss the technology and advantages of RockWeb as well as opportunities for overall mining cycle cost reduction. The safety benefits, as well as health and environmental considerations regarding application of isocyanate-based liners will also be discussed.

May 1, 2009

By A. Carbonari

In order to gain competitiveness and compete at a global level, construction companies should improve their efficiency. The problem is even more relevant in the construction field, whose work processes find it hard to evolve towards new automated methods and techniques in the management field. For that reason, this paper suggests how construction companies could apply new technologies to implement automated management of environmental hazards. Based on a survey regarding the environmental risks presently experienced in construction sites, noise and dust were considered two of the main hazards. So in this paper a networked system for real time remote monitoring of the spatial distribution of dust in construction sites was developed. Such a system would relieve builders from the commitment of on-site surveys, allowing for a continuous monitoring of the site conditions and of the real exposure of each worker and pass-by to the pollutants generated by construction works. The main system requirements considered are: easy to deploy, reliable, as accurate as needed to be able to send real-time warnings and store a good estimation of the real exposure to which involved people have been subject to. So far the research produced a prototypical hardware for dust monitoring made up of wireless sensors which can be easily deployed on site. The sensors were calibrated by means of laboratory tests, where their measurements were compared with those collected by means of highly accurate instruments, which were taken as a reference. Thanks to these experiments, calibration curves for the sensors were worked out, showing also the measurement range of the sensors.

Aug 1, 2013

By Baisheng Nie

The process of gas diffusion through coal particles and the mathematical physical model under the third kind boundary condition was determined to obtain the rules of gas diffusion through coal particles of different sizes. The analytical solution of the equation was obtained by the Method of Mathematical Physics. The parameters of analytical solutions and the implications of parameters were analyzed. The Biot criterion (Bi) and the Fourier criterion (F0) of mass transfer can represent and reflect the features of gas diffusion field of coal particles. Moreover, the measurement method of gas diffusion coefficient and surface mass transfer coefficient is introduced and an example of measurement is given. The achievement can provide the support to prevent disasters related to methane in coal mines.

Aug 1, 2013

By Randy McMeekin, Chris Twigge-Molecey, J. Peter Blake

The business objectives of a metallurgical project determine targets and constraints, such as the range of products, production capacities, in-service dates, and capital and operating cost parameters. Permitting is usually left to the project team, as are decisions regarding site location, technology, and construction approach. Success requires an orderly methodology, represented in this book by front end loading (FEL) phases: FEL1 examines several alternative approaches; FEL2 ranks and eliminates less economically or technically attractive options; and FEL3 develops the preferred option to the point of major permit completion, with defined scope, schedule, and cost to submit for approval to proceed with implementation in FEL4. Working through FEL1, FEL2, and FEL3, the project definition improves, estimates become more accurate, and project risks are reduced. The project design basis at the end of FEL3 is the control document for project implementation in FEL4.

Jan 1, 2015

While this paper is directed towards the ?Bellambie? type of rope attachment, the principles can be applied to any brand of rope fitting however, it is a only a broad outline and the specific installation and maintenance procedures can be obtained from the attachment supplier. The types of attachment to be discussed are:- ?Thimble Type rope cappel ?Wedge Type cappel ?WRC Rope Clamp ? (Rope Glands) ??Hoist and Balance Rope Sockets In each case, the assembly and stripping (disassembly) plus the basic maintenance procedures is briefly described. A guide for Risk Assessment is also included but because of his familiarity with the installation, the end-user is in the best position to draft the final version.

May 1, 2003

By C. Schmidt, M. Kohnk, C. Siemers, J. Kiese

The application of conventional titanium alloys is limited to 550°C due to their poor oxidation resistance. In addition, severe grain growth is observed in single-phase titanium alloys in long-term runs at elevated temperature leading to a degradation of their mechanical properties. In exhaust applications in automotive or aerospace engineering, products are often manufactured by cold-deformation like deep-drawing or rolling which is normally difficult in oxidation-resistant titanium alloys due to the presence of titanium-silicides. Therefore, in the current study, titanium alloys based on CP Titanium Grade 1S (soft grade) were developed showing (1) improved oxidation resistance due to a concerted addition of silicon, iron and niobium, (2) microstructure stability by the precipitation of hafnium-silicides mainly on the grain boundaries and (3) good cold-deformation properties. The industrial production route was developed so that the new class of Ti-Si-Fe-Nb-Hf-alloys is now ready for application in exhaust systems of planes or cars at minimum 800°C.

Jan 1, 2015

By T. R. Kostecki, K. V. Jessu

"Roof bolts are subjected to axial stresses, shear stresses, or both. Axial and shear stresses were compared between roof bolts machined with two and three slots. Shear stresses perpendicular to and at an angle to the shear planes were evaluated by analyzing a three-slot instrumented roof bolt, performing laboratory tests on two- and three-slot roof bolts, and conducting in-situ test analyses. Threeslot bolts appear to provide a complete bending strain profile, requiring no prior knowledge of the estimated shear-plane orientation. Minimum displacements occur in roof bolts installed perpendicular to rather than at an angle to the shear planes.RÉSUMÉ Les boulons d’ancrage dans le toit d’une mine sont sujets à des contraintes axiales, des contraintes de cisaillement ou les deux. On a comparé les contraintes axiales et de cisaillement de boulons d’ancrage usinés avec deux ou trois fentes. Les contraintes de cisaillement perpendiculaires et à angle aux plans de cisaillement ont été évaluées en analysant un boulon d’ancrage de toit à trois fentes, en effectuant des essais en laboratoire sur des boulons d’ancrage de toit à deux et à trois fentes et en effectuant des analyses de tests in situ. Les boulons à trois fentes semblent fournir un profil complet de résistance aux contraintes de flexion, sans avoir besoin de connaître l’orientation estimée du plan de cisaillement. Des déplacements minimums ont lieu dans les boulons d’ancrage de toit installés perpendiculairement, plutôt qu’à un angle, aux plans de cisaillement."

Jan 1, 2016

By N. Aydogan, H. Dundar, Å. Partapuoli, A. Fredriksson, P. Wikström, K. Tano, G. Adolfsson

The Autogenous milling of ores holds an increasing attraction as the focus moves towards reducing energy usage, both direct and embodied in grinding media. However, most of the early AG mills were converted to SAG for improved stability and increased throughput. This imposes a huge penalty in steel grinding media consumption. The LKAB iron ore operations in Sweden process highgrade magnetite through fully-autogenous milling lines to a final product P80 of about 45µm. The outcomes of P9O AMIRA research surveys, covering a wide range of mill fillings and throughputs and with different feed blends, are presented. Insights are provided on operational strategies, opportunities, the influence of feed size control and balancing the blend of competent gangue and softer magnetite. Areas of importance in the successful operation and control of energy-efficient autogenous circuits are highlighted.

Jan 1, 2012

By Paul B. Batten

Shutdown is a generic term for what may be called an Outage, Turn Around (TAR) or Overhaul etc. Running a plant shutdown well has always been key to the financial contribution of a mine. However, something important has changed. The post pandemic reality is that it is harder to retain workers and many of those near retirement just didn’t come back to work. This is creating a shortage of experienced people and a workforce that changes employers easily. We are seeing the impact of this manifested in the erosion of established maintenance and supply chain processes that now struggle to yield the plant runtime that could once be taken for granted. The scope, cost and duration of a shutdown varies widely depending on the nature of the work and the equipment being renewed. The PM of an electric shovel might require a week of downtime and cost $100,000. A gold plant may need to go down for 3 days when its time to change mill liners and cost $500,000. A turnaround in a refinery can take more than a month and cost multi millions. Despite the huge differences.

Jan 1, 2023

By B. P. Verma, K. N. Sinha, N. M. Raju, B. Singh

The paper describes a new method of grouting bolts developed at the Central Mining Research Station at Dhanbad in India. This method makes use of wire-mesh sleeve instead of the expensive metal tube to insert the cement mortar into the drill hole. The field trials confirmed that the method is cheap and an effective system of support.

Jan 1, 1972