Search Documents

By G. F. Colborne, A. Thunaes

"When the Canadian uranium milling plants went into operation during the early 1950's, they utilized flowsheets developed at the Radioactivity Division of the Federal Mines Branch in Ottawa. Since then, numerous process improvements have been made by the Mines Branch, by the operating companies themselves and by other research organizations. This paper will consider uranium milling technology from the standpoint of a new mine operator charged with the responsibility for the design of an economic flowsheet, and will indicate the range of process elements available to him and the testwork required to enable an intelligent decision to be made."

Jan 1, 1968

By V. V. Pankov, W. R. Chen, L. R. Zhao

Diffusion nickel aluminide and overlay NiCrAlY coatings were deposited on single crystal Ni-base superalloy CMSX-4 substrate using the chemical vapour deposition and cathodic arc evaporation techniques, respectively. The NiCrAlY coating underwent a post-deposition heat treatment in an argon atmosphere at 1100°C for 2 hours. All the coated specimens were subjected to furnace cyclic oxidation testing at 1000°C up to 1500 one-hour cycles. The morphology, elemental composition and phase constituents of the oxide scales formed on the coating surface were analyzed using scanning electron microscopy, energy-dispersive spectroscopy and X-ray diffraction. It was observed that the diffusion aluminide coating experienced accelerated weight gain at an early stage of the test (150-400 cycles), whereas the overlay NiCrAlY coating fabricated by cathodic arc evaporation maintained steady-state weight gain throughout the entire 1500 cycle test duration. This difference in oxidation behaviour between the two types of coatings is attributed to the early development of nickel-aluminum spinel on the surface of the diffusion aluminide coating, in contrast to the stable aluminum oxide scale formed on the overlay NiCrAlY coating during cyclic oxidation testing.

Jan 1, 2015

By K. Morin, C. -Y. Hon, G. Lachapelle

"Air-sampling results suggest drill operators working inside environmental drilling cabs at an open-pit gold mine in Nunavut, Canada, are at risk of exposure to asbestos and silica (quartz). The authors installed RESPA® CF Vortex HyperFLOW® units, which showed promising results under laboratory conditions. The goal was to evaluate the effectiveness of these units under actual working conditions. Personal and area air sampling was conducted in drilling cabs with and without the unit and a Wilcoxon rank-sum test was performed to compare the results. Particulate concentrations were significantly lower in drill cabs with a unit installed than in those without.RÉSUMÉ Selon les résultats d’une campagne d’échantillonnage de l’air, les foreurs travaillant dans des cabines de forage environnemental dans une mine d’or à ciel ouvert du Nunavut, au Canada, risquent d’être exposés à l’amiante et la silice (sous forme de quartz). Les auteurs ont installé des unités RESPA® CF Vortex HyperFLOW®, lesquelles of frent des résultats prometteurs en laboratoire. L’objectif est d’évaluer l’efficacité de ces unités dans des conditions de travail réelles. Des échantillons de l’air inhalé par le personnel et dans les aires de travail ont été évalués dans des cabines de foreuses équipées ou non de cette unité ; un test de Wilcoxon (également appelé test de la somme des rangs de Wilcoxon) a été mené afin de comparer les résultats. Les concentrations particulaires étaient considérablement plus faibles dans les cabines de foreuses équipées d’une unité que dans celles en étant dépourvues.INTRODUCTIONGenerally, mining operations are associated with a variety of occupational hazards. In an open-pit gold mine in Nunavut, Canada, drill operators are routinely exposed to asbestos (primarily amosite) and silica (quartz)—two naturally occurring substances in the ore that is to be drilled (Table 1). Inhalation is the primary route of exposure for these two hazards, which are associated with respiratory health effects such as asbestosis and silicosis, respectively. In addition, asbestos and silica are classified as human carcinogens by the International Agency for Research in Cancer (2001, 2011). Given the toxicity of these two agents, it is imperative that precautions be taken to minimize the risk of exposure of the mine’s workforce. To address this matter, the mine has an exposure-control plan, which includes the provision of personal protective equipment, personal hygiene facilities, training, and a medical surveillance program. Furthermore, the mine performs occupational exposure assessments or air sampling on a regular basis because the morphology of the ore changes rapidly with respect to asbestos and silica content."

Jan 1, 2017

By S. Southall, F. McCaffrey, F. Stober, M. Darini

Electrode Columns are commonly used in electric furnaces to deliver current and regulate furnace power to the smelting or melting process. Hatch has developed an innovative patent-pending system for lowering ("slipping") and/or raising ("back-slipping") the electrodes through an electrode column, without requiring the release of any clamping devices. All clamping forces are applied by springs. Unlike systems employing hydraulically applied clamping forces, (e.g., water bladders) the spring system is failsafe. Its inherent simplicity virtually eliminates the need for maintenance. The Hatch system is particularly applicable to Soderberg electrodes, and comprises two axially movable slipping clamps and a stationary power clamp, each of which apply a distributed, radial clamping force to the electrode. The magnitudes of the slipping sleeves' clamping forces and sequencing of their axial movements are selected such that the slipping clamps, in conjunction with the weight of the electrode, provide slipping or back slipping without release of any clamping force.

Jan 1, 2005

By W. D. Breil, C. B. Ison

A collection of general performance data relating to the G.H.H. - Gutehoffnungshiitte multi-rope friction hoist will be discussed together with some aspects of the following: overspeed supervision by a pantam device as opposed to the lilly type of fly ball control, automatic control systems, multi-disc braking, generator and motor winding, constant temperature monitoring, the development of an automatic hoist-rope lubrication system, and the control of rope tensions by the installation of G.H.H. - Gutehoffnungshiitte hoist rope fine tensioning units.

Jan 1, 1972

By W. D. Robbson

DR. G. W. RAMSEY (l): A study of our non-treatment silicosis autopsy material for the years 1940-43 inclusive, in addition to the common findings of fibrosis, nodules, and emphysema, shows marked thickening of the alveolar walls. This change is due to one or more of the following factors: congestion, edema, accumulation of both small and large monocuclear cells within the interstitial tissues and large monocuclear cells attached to the lining membrane of the alveolar sacs. This alteration in the alveolar walls, we believe, is one of the most important factors in producing impaired pulmonary function. Comparison of our first autopsy material of a case receiving twenty aluminium treatments beginning June, 1943, shows a striking change in the alveolar walls. In all areas free of silocotic nodules and fibrous tissue, the alveolar walls approach normal thickness and are free of cellular deposits. No change was noted in the old processes and none was expected. We believe that these changes in the alveolar walls were brought about by the aluminium therapy and that they constitute a major factor in the improved pulmonary ventilation noted in treatment cases.

Jan 1, 1945

By Gordon Thompson

"Development of the unique Mine Games exhibition at Science World British Columbia is the largest ever collaboration of many interests to present the story of mining and the issues of mineral development delivered to the public by a science education centre.IntroductionMineral education programs have long been a major focus of the British Columbia mining community. Mine Games and its tremendous potential to enhance industries image and the public's awareness of mining is unequalled in the field of Issue Based Education Exhibits.The main goal of the exhibition is to look at the future of resource industries in a rapidly changing world of economic activities, new technologies, and growing public concern for the environment. Three challenges were the aim of the exhibition: to increase participation, to serve as a tool to increase interest in science and technology, and to draw an increasing number of school students to the interests of geology and the earth sciences. Mine Games is to serve as a meeting place for discussion of issues and where reliable information can be shared and new ideas explored.The exhibition is designed to develop new approaches to hands on learning that encourages visitors to explore and generate discussion and thinking with respect to resource development activities.The role of author, beginning in 1993, was, with senior industry leaders, to coordinate the raising of $1.3 million to complete the funding of the $1.6 million project total. The second and most interesting challenge was to work with the many minds that were collaborating to create the exhibition and to assure that the facts and science were correct. This involved the coordination of ""expert groups"" that verified the science and technology and the issues that the creative design team at Science World planned to use in development of each exhibit module."

Jan 1, 1995

By J. E. Amadi-Echendu, F. Stober, J. Ndlovu, L. R. Nelson

The Polokwane Smelter Complex (PSC) relies on a single 68MW high-intensity six-in-line furnace to smelt a planned 650 000 t/a dry concentrate to produce a platinum group metals (PGM)-bearing matte. As typical of a greenfields venture, considerable attention was paid to the project development and implementation stages of design, engineering, construction and commissioning. Somewhat unusual though, was the role of a dedicated multi-disciplinary "Operational Readiness" and support team, comprising the owners team and specialists from the furnace designer, HATCH, to effect a safe and rapid ramp-up to the design smelter capacity of 68MW. The challenges encountered in developing an effective partnership will be discussed. The modus operandi and roles of the "Operational Readiness" team during the design, procurement, construction and commissioning stages as well as that of the operational support team within the overall ramp-up objective will be presented. The "Operational Readiness" team was responsible for:

Jan 1, 2005

By M. Labrie, H. L. Gibson, G. Doiron, J. J. Watkins, D. H. Watkinson

Abstract -The Corbet deposit is one of 17 proximal Cu-Zn massive sulfide deposits located. within the Noranda Cauldron which occurs within the core of the Noranda Volcanic Complex. The deposit is located at the top of the F1avrian Formation, the lowermost formation of the 3000 m thick Mine Sequence; the deposit has yielded 2.75 M tonnes of ore grading 30Jo Cu, 0.96% Zn, 2.06 g/t Ag and 1.0 g/t Au. The multi-lens Corbet deposit formed within a 250 m wide crater that occurs within a localized breccia pile. The Corbet breccia pile was constructed by explosive magmatic and hydrovolcanic eruptions localized along the south flank of a larger andesitic shield volcano that formed during the waning stages of F1avrian volcanism. The breccia footwall of the deposit allowed unfocused and widespread hydrothermal discharge that resulted in the development of a large area of chlorite and fringing sericite alteration that exceeds, by six times, the size of the sulfide lenses and represents a significant exploration target.

Jan 1, 1993

By W. Blum

Progress made in improving the creep resistance of Mg alloys is reviewed with the emphasis on microstructural interpretation. Experimental results on the increase of creep strain with time at constant stress a measured for limited times and strains are displayed in a transparent form as creep rate-strain diagrams from which the minimum creep rate stress is safely derived. In addition, data on the thermal stress component a derived from high-precision a-reduction tests are reported. Within a simple statistical dislocation model these data allow one to quantify the relation between dislocation velocity v and a . In combination with structure evolution laws this relation serves as a basis for modeling the creep rate. New alloys have distinctly higher creep resistance than AZ91 where precipitation hardening plays a minor role. This is due to hardening by intermetallic phases which may form a continuous skeleton along the grain boundaries (e.g. Ca-alloyed AZ91) and/or submicron-sized precipitates within the grains (MRI230D, Mg-Zn-Ca alloys).

Jan 1, 2006

By Lin-fang Shen, Shao-jun Li, Zhi-liang Wang

"The meso-structure of real soil consists of numerous particles with different sizes, while the traditional reconstruction method of quartet structure generation set (QSGS) produce relatively uniform soil particles resulting in significant discrepancy between the actual structure and reconfiguration model. In order to remedy the deficiency, the QSGS is improved by considering the influence of porosity and autocorrelative function of soil, which make the models closer to the real soil. Based on the reconfiguration model, Lattice Boltzmann method is combined in the algorithm to conduct further simulation of fluid flow in soil pores. The D2Q9 model is applied to construct the two dimensional model for simulating mesoscopic seepage field of saturated soil by setting the non-equilibrium extrapolation scheme at the inlet and outlet boundary, and the bounce-back scheme at the soil particles boundary as well as the left and right boundary. According to the case study, the proposed program is realized to simulate mesoscopic seepage field of reconstructed soil with constant inlet seepage velocity. The results show that the seepage direction of soil is along the passage with good connectivity, therefore the permeability is controlled by these passages. The seepage velocity in such channels is faster than in bad connectivity channels. Even if the channel has larger pores, the seepage velocity is still small. INTRODUCTIONUnderstanding the seepage mechanism in porous materials is significant in both theoretical and engineering problems. As a typical porous media, soil consists of solid particles and voids, which form connected channels allowing water to flow through. Such seepage in soil exists widely among geotechnical project of slope, foundation pit, and tunnel, etc. Meanwhile, a number of engineering accidents are caused by limited knowledge of seepage characters in soil (Huang, 2006; Liu, 2013). The conventional method in describing seepage features mostly based on the parameter of permeability, which is a macro statistic mean evaluating the whole connectivity of soil. Obviously, this parameter cannot exactly reflect the details of how water flows through the inner soil structure, especially the flow velocity in local mesoscopic area, hence is unable to represent the actual seepage properties. Therefore, it is necessary to develop mesoscopic approaches to fully study the seepage mechanisms."

Jan 1, 2015

By Marty Hudyma

There are five independent seismic source parameters: seismic energy, seismic moment, source size, location, and time. These parameters are investigated primarily for evaluating seismic hazard and understanding seismic source mechanism(s). Broadly, seismic hazard is the likelihood of occurrence of an event of a given magnitude. Seismic source mechanism is the mode of rockmass failure that causes the seismic event. Most mine seismicity analysis techniques use a combination of a few of the independent source parameters. In literature, time is perhaps the least discussed and most underutilized of these five parameters. This paper discusses three applications of time to understand both seismic hazard and seismic source mechanism in mines. The first application is time history analyses, which focuses on how other parameters of interest vary over time. Examples are presented to show how time history analyses can give information about both seismic hazard and seismic source mechanism. The second application is analysis of time-between-events. This technique can give insight into seismic source mechanism. The final application is phasor analysis using the Schuster test. This method can be used to investigate how seismic source mechanisms may change over time. For both time-between-events analysis and phasor analysis, there are important implications with regards to scale dependence and the breakdown of self-similarity of mining-induced seismicity.

Jun 1, 2012

By Allan R. Punkkinen

Safe extraction of the valued ore resource in the deep levels of VALE Creighton Mine has progressed in a pillar-less fashion using vertical retreat, slot-slash and uppers retreat methods since the cessation of ?cut and fill? mining in the late 1980?s. Sequencing of the panel extraction and filling has been the key to successful exploitation of high stress orebodies at depth. In late 2010, discussions between the Operating Department and Creighton Ground Control revealed an opportunity to evaluate a trial primarysecondary sequence in the west end of the 400 Orebody at the 2340m horizon. To manage the trial primarysecondary project, a high level risk analysis and management of change was carried out to mitigate potential danger. As part of the requirements, an instrumentation project was conducted in the hanging wall and footwall bottomsills of the secondary panel and within the secondary panel itself. The extraction sequence was modeled with Map3D® software, confirming high stress levels with the advance of the primary panel. Enhanced ground support was installed based on modelling results. A key objective of the instrumentation project was to verify support system response to mining and to obtain knowledge in regards to the behavior of the stope. This paper describes the first time that this type of new innovative instrumented rockbolt technology had been used in a hard rock mining environment. Understanding of the physical deformation mechanisms of ground support in response to high stress conditions is the basis for an effective ground control strategy. The data played an important role in subsequent enhanced ground support system design at the mine and importantly, established the fact that the secondary pillar had not totally failed. Subsequent cavity monitor results helped establish that fact.

Jun 1, 2012

By H. R. Oliveira, C. R. Aragonez de Vasconcellos

Pipeline operation and maintenance necessarily involves geotechnical studies at points and areas with deflagrated instabilities or still to map and monitor areas prone to geotechnical problems. Landslides, erosions and debris flows are some examples of natural hazards, that not rarely, can bring high consequences to pipelines, sometimes leading them to high stresses levels and ruptures. Bolivia-Brazil Natural Gas Pipeline has 2.593 kilometers since Rio Grande City in Bolivia until Canoas City, in south Brazil. The pipeline crosses a lot of types of geological fields and difficult topography. The south spread of the pipeline has the most prone areas to geotechnical hazards because of its hard topography combined with the variety of geological materials, such as, colluvium deposits and debris flow areas. The aim of this paper is to present the right-of-way geotechnical risks that affect pipelines, presenting some practical remedial works done by TBG at Bolivia-Brazil Natural Gas Pipeline as well as the integrity plan and the adopted actions in way to prevent geotechnical accidents.

Jan 1, 2005

By G. A. Sutton

"At the San Manuel mine (Arizona, USA), in-situ copper leaching of a copper porphyry deposit was carried out from 1986 to 1999 during underground and open-pit mining. In 1993–1994, well¬field testing of the supergene zone, composed primarily of chrysocolla and copper-rich clay minerals, led to estimates that 52% of the acid-soluble copper (ASCu) could be recovered during in-situ leaching; however, the actual recovery from zone 6, which had the longest leach history, was approximately 42%. Comparing drillcore assay data from holes drilled before and after leaching also indicated an approximate recovery of 42%. The discrepancy between the predicted (52%) and actual (42%) recovery is probably related to several factors, including difficulty maintaining fluid saturation, channelling effects, and gypsum precipitation. ¦ KEYWORDS Copper oxides, in-situ leaching, Modelling, Porphyry, Solvent extraction and electrowinning (SXEW), Well-to-well RÉSUMÉ À la mine San Manuel (Arizona, États-Unis), on a procédé de 1986 à 1999 à la lixiviation in-situ de cuivre d’un gisement porphyre cuprifère pendant l’exploitation minière souterraine et à ciel ouvert. En 1993 et 1994, des essais effectués dans des champs de captage de la zone supergène, composée principalement de chrysocolle et de minéraux argileux cuprifères, ont abouti à des estimations selon lesquelles on peut récupérer 52 % de cuivre soluble dans l’acide (ASCu) pendant la lixiviation in-situ ; toutefois, la récupération réelle dans la zone 6, qui affiche l’histoire la plus ancienne en matière de lixiviation, était d’environ 42 %. La comparaison des données d’analyses de forage obtenues à partir de trous forés avant et après la lixiviation indiquait également une récupération approximative de 42 %. La différence entre la récupération prévue (52 %) et réelle (42 %) réside probablement dans plusieurs facteurs, notamment la difficulté à maintenir la saturation des fluides, les effets de canalisation et la précipitation du gypse. ¦ MOTS CLÉS d’un puits à l’autre, extraction par solvant et extraction électrolytique (SXEW), lixiviation in-situ, modélisation, oxydes de cuivre, porphyreINTRODUCTION in-situ copper leaching at the San Manuel mine, Arizona, USA (Figure 1), began in 1986. It was recognized that some of the copper oxide resource was not economically recoverable by conventional open-pit and heap leach methods using solvent extraction and electrowinning (SXEW) and a high stripping ratio would be required to access part of the resource. At the time, in-situ leaching was becoming popular in the uranium industry, but the approach was virtually unknown in the copper industry, especially at a large scale."

Jan 1, 2019

By T. R. Stanley

Introduction The purpose of this paper is to interest mining men in the economic possibilities of sand deposits suitable for modern foundry work. Many members of the profession are constantly travelling over the country and it is felt that some knowledge of the necessary properties of foundry sands will enable these men t0 recognize such deposits. It is the experience of the writer that good sands suitable for the varied work of a foundry, such as that of the Consolidated Mining and Smelting Company, at Trail, are almost impossible to obtain from western Canadian sources. It is hoped that the following discussion may arouse some interest in the search for such sands. Sands are used in foundries for two purposes. The main use is for making moulds suitable for receiving hot metal. The mould must retain the? required shape until the metal has solidified. The second use of sand in the foundry is as an abrasive in sand blasting. This is a relatively minor use, and consequently will not be dealt with in detail. Any coarse sand with a high content of quartz will serve this purpose, but round-grained sands are superior to angular types, because they have not the same tendency to shatter on impact with the casting. Sand plays an extremely important part in the successful production of sound castings. This is more evident today than ever before, due to the greater variety of castings and alloys, each of which requires special sand characteristics. Poor sand is responsible for a great many foundry troubles which formerly were attributed to bad? metal; in fact, one investigator goes so far as to say that ninety per cent of bad castings can be traced directly to the sand. Very little of the vast amount of sand distributed over the earth's surface is suitable for moulding. It is the purpose of this paper to describe briefly the properties which are essential in good moulding sand. Sand for this work must be able to withstand the wash and hydrostatic pressure of molten metal, and yet be sufficiently porous to allow the gases generated in the mould to escape.

Jan 1, 1935

By Mei-Yan Yang, Qiu-Ying Wang, Ltd. Yunnan Yuntong Zinc Co., Guo-Mu Chen, Meng-Yang Huang, Peng Zeng, Guo-Feng Li

"Historically, alot of jarosite was found in the leaching residue when leaching indium from secondary zinc oxide materials. The reasons for the formation of indium bearing jarosite were theoretically analyzed. The influence of controlling the acidity and the addition of reagents on the indium leaching yield during secondary zinc oxide processing was investigated. In order to increase the leaching yield of indium, a measure of controlling the creation and destruction of jarosite was proposed. The production data shows that the leaching yield of indium was increased from 60 to 96%, and the content of indium in leaching residue simultaneously decreased from 900g/t to 100–200g/t when implementing such controlling measures.INTRODUCTIONIndium does not occur as independent minerals in the earth’s crust and is mainly associated with complex sulphide minerals. Specifically some sphalerites can contain as much as 900g/t of indium. Most indium is recovered from by-products of copper, lead or zinc metallurgy. Therefore, the research on the recovery of by-products in non-ferrous metallurgy is important(Sinclair et al, 2006). The main technologies used for this objective in China include: •,pre-neutralization-reduction-precipitation indium process(Yu et al, 2008), •,countercurrent oxidizing acid leaching process and sulphation roasting-water leaching process(Cao, 2005), •,oxygen pressure acid leaching of zinc concentrate-P204 extraction process(Yang et al, 2006), •,doubleacid leaching-solvent extraction process on lead dross from a reverbatory furnace flue dust(Liu, 2003),•,an acid leaching-solvent extraction process on smelting ash(Zhouet al, 2005). Although high pressure and extreme conditions can be used to improve extraction from high iron bearing indium residues(autoclave processing), mild extraction with lower cost and lower environmental impact are preferred.This paper describes both how the indium extraction using mild conditions in a secondary zinc circuit was quite low and, how through XRD and chemical analysis jarosite formation was found as the main cause. The paper then proceeds to discuss a method for improving the leaching yield and the application of this method in industrial practice."

Jan 1, 2016

By R. C. Becker

Welding is playing an important role in the manufacture of construction equipment as used in the mining industry. It provides design possibilities which are unique to this method of manufacture, and normally makes possible lighter weight but stronger products, which can be a definite advantage to a user. Welding is an industry that has experienced major developments over the past decade, all of which have improved our capability to make better welds and make them more economically. International Harvester Company has been introducing these newer welding methods into its manufacturing plants, particularly those producing construction equipment, just as fast as their value has been proven. This paper discusses how modern welding methods are contributing to the manufacture of strip mining equipment.

Jan 1, 1966

?Introduction to the Delphi Group ?Why is carbon important to your organization ?Key elements of a carbon management strategy ?Inventory ?Risk & opportunity scan ?Mitigation options and financial mechanisms ?Identify targets and develop policy ?Communication and improvement ?Manage for success

May 1, 2009

By F G. Cooke

"This paper describes a medium-sized copper mine's results in making innovations and changing operational practices to combat increasing expenditures due to higher labour and supply costs, extended workings, scarcity of experienced manpower and problems created by deteriorating ground conditions.OPEMISKA COPPER MINES (QUEBEC) LIMITED is located at Chapais in the Chibougamau area, in central eastern Quebec, approximately 300 miles north of Montreal and 150 miles north west of Lake St. John. The latter area, developed by lumbering and farming, has supplied the majority of the employees, who, with training and experience and a desire to work and improve themselves, have become the backbone of the Company's 600 personnel.Opemiska began production in 1954 at a rate of 400 tons per day, using diesel power and road transportation. The rate was progressively increased and, by 1959, with hydro-electric power and rail transportation, the mine had reached its present production rate of 2,000 tons per day. It has produced concentrates containing over 430 million lbs of copper."

Jan 1, 1968