Search Documents

By L. I. Kiss, S. Perron, S. Poncsák, A. Perron

Aluminium industry has an increasing interest in the diminution of the energy consumption of the Hall-Heroult process by the reduction of the anode bottom covering with gas. Electrically isolating carbon-dioxide bubbles, produced at the anode, increase the ohmic resistance of the cell. As the gas production rate is determined by the applied current density, anode covering can be decreased only by a faster evacuation of the gas from the inter-electrode space. Among others, the inclination and curvature of the anode bottom promotes the release of the bubbles and thus decreases the mean value of the covering. Indeed, anode, insert in the molten cryolite bath has a square shape with horizontal bottom. However, inhomogeneous anode consumption, electro-erosion, bath circulation and the inclination of the bath-metal interface modify this shape gradually during electrolysis. Anode bottoms become inclined with rounded comers. This concentrates the gas generation to the center zone of the anode. As the bubble layer cannot be observed directly because of the hostile environment and the opacity of the bath, real scale air-water systems are used to study the impact of the anode geometry on the anode covering and the bubble induced flow. However, the physical properties of such a system are different than that we can found in the real cells. A simulator using the Lagrangian description of the bubble layer has been built and presented in earlier papers. This tool was used to investigate the effect of the anode inclination on gas covering and bath velocity, for both C02-cryolite and air-water system. Results obtained for the second system were compared to experimental data .

Jan 1, 2006

By P. M. Shibley

"IntroductionMine drainage, surface. drainage and process liquors are the principal mine and mill effluents. The quantity and quality of these flows varies according to mineralogy, type and scale of mining, the process, tailing disposal, local ground conditions and climate.Typical contaminants remaining after solids sedimentation are colloidal or semi-colloidal particles, acids, alkalis, metals in solution, cyanides and thiosalts. Environmental regulations and guidelines have been issued in detail by the appropriate government agencies and will not be reviewed here. Revisions and additions are being made as our comprehension and abilities increase. Some contaminants of consequence have not been specifically regulated as practical treatment technology has not been identified. Thiosalts fall into that category as do the derivatives of the first stage of cyanide oxidation - cyanates.Most mining activities have present or foreseeable water treatment requirements. Because process economics can be adversely skewed by the environmental factor, the acknowledged objective of every operation must be to identify and anticipate those requirements.The evaluation and selection of water treatment techniques for mine-mill applications is complicated by the fact that most mine-mill effluents are high volume, dilute and chemically complex systems. Treatment processes applicable to most contaminants are: chemical or biological oxidation; neutralization and/or precipitation; liquid/solids separation. Other processes such as ion exchange, electro-deposition, foam fractionation, freeze crystallization and reverse osmosis offer the possibility of selective removal or concentration of contaminents. The latter tediniques, representing a slightly higher level of technology, are less suited to the large, low value flows usually encountered in the mine environment."

Jan 1, 1989

By A J. Kyle

After a brief description of the shaft and surface facilities, this paper describes the planning for the mining operation, the selection of equipment the general method of mining and the sequence of operation. All of the major items of equipment are described, including the components of the power system. The detailed planning is reviewed -from the shaft sinking to the three-shift mining operation. Excavation and equipment changes, as well as long-range planning, are al o di cussed. Introduction THE successful completion of the Yarbo No. 1 shaft of International Minerals & Chemical Corporation (Canada) Limited in July, 1962, added a new type of mine to Canada&apos;s many producing operations. IMC Esterhazy is a unique mining operation in Canada; in fact, it is unique to potash mining in general. Not only is thi&apos;3 a trackless operation utilizing shuttle cars and belt conveyors in its material handling systems, but it excavates all of the ore with continuous boring machine<:;.

Jan 1, 1964

By J. C. Folinsbee, D. R. Derry

"The Property of Opemiska Copper Mines (Quebec) Ltd. is in Levy Township, Chibougamau district, west of Chibougamau and south of Opemiska Lake. The original find was made in 1929 by the late Leo Springer and associates of Prospectors Airways Ltd., following observation from the air of an area of dark rocks in newly burned-over country. Work on the ground discovered three veins of high-grade chalcopyrite in gabbro (No. l, No. 2, and ""North"") and, after several seasons of trenching and diamond drilling, financed by Ventures Ltd., a shaft was sunk in 1936. This work indicated about 280,000 tons of six per cent copper ore to a depth of 500 feet. During this period, the senior author carried out a reconnaissance geological survey over the whole property and surrounding claims, which showed that the veins were in the gabbro portion of a large composite basic sill that had been folded with the enclosing lavas. Owing to the low price of copper and lack of transport work was suspended and the property remained dormant until 1951.In that year the company was re-financed, the property prepared for production, and further exploratory drilling undertaken. The drilling, based on structural indications, located a new vein of which the only previous evidence had been some irregular stringers. This vein, No. 3, was traced by drilling for a length of 2,000 feet and the indicated reserves were thereby increased to about one million tons. An additional vein, No. 4, was intersected in several holes.With this encouragement, plans for production were confirmed, and operations commenced' at the beginning of 1954 on a scale of about 400 tons a day, concentrates being shipped by truck to St. Felicien and thence by rail to Noranda. In the first year of operation concentrates were re-covered carrying 14,047,210 pounds of copper, 76,714 ounces of silver, and 6,259 ounces of gold. The operation is under the direction of J. P. Millenbach, General Manager, with J. M. Thompson as Assistant General Manager and F. G. Cooke as General Superintendent on the property."

Jan 1, 1949

By G. Ergin

The interactions taking place between Al-Mg alloys and the bed media during aluminum filtration are not yet well understood. These interactions were studied using the infiltration technique. The reaction interface was analyzed using different techniques such as SEM and TEM. Only spinel formation was observed at the interface regardless of the type of alumina and contact time. This paper discusses the results of the study.

Jan 1, 2004

By John A. C. Fortescue

Details of the interactions between the environment and the growth of terrestrial plants may be complex and difficult to study. This paper focusses attention on some of these complexities by means of six examples, each of which provides information on an aspect of the interaction between the growth rate of plants and the chemistry of the environment. The relationships which exist between the information obtained from these examples and the concepts of "holism" and "transfer rate problems" are pointed out and the importance of long-term biog•eochemical studies in Canadian environments is stressed.

Jan 1, 1971

By A. B. Baldwin

"Uranium and thorium mineralization occurs at several localities in eastern Quebec along the north shore of the Gulf of St. Lawrence. The main occurrences are near Sept-Iles, Baie Johan Beetz, Romaine and St-Augustin river. Mineralization occurs mainly as disseminated uraninite, uranothorite, uranothorianite, monazite and minor zircon and allanite. Yellow to orange oxidation products are observed along fracture planes of the uranium-bearing deposits to a depth of a few feet. Magnetite, biotite and smoky quartz have a distinct tendency to accompany the radioactive minerals. The host rocks include white to pink pegmatite, pink granite and also, in the case of the Romaine and St-Augustin River occurrences, cream to grey plagioclase-rich, well foliated paragneiss and migmatite. Radioactivity near secondary structures, such as fractures and joint planes, indicates some reconstitution of radioactive minerals.The North Shore of Quebec is the northeast extension of the Grenville sub-province. It is also a uranium-thorium metallogenic province."

Jan 1, 1970

By W. S. Fyfe

Gold is mobilized and precipitated in a wide variety of environments ranging from those of weathering and biological phenomena, to pluton emplacement to deep metamorph ism . But it appear that pervas ive leaching of large rock volumes fo llowed by the focussed di charge of typically low salin ity flu ids is frequently involved. There are great gaps in our knowledge, particula rly with re pect to gold in very high temperature fl uids generated at near Moho depths. But uch flu id may play an important part in Archaean pluton associated lode gold deposits whe re ultra high temperature fluids, rich in C02-CO-COS, may be associated with magma underplating and crustal assi mil ation processes (sag subduction) associated with very den e ult ramafic magma . Other environment with great potential include those of major thru t fau lt and strike slip fa ult s where large quant ities of fluids are mobilized .

Jan 1, 1986

By K. Sun, S. A. Argyropoulos

The assimilation and the exothermic behavior of Zn-Zr metallic powder compacts into molten aluminum was studied by measuring simultaneously the temperatures inside at the centerline of the compact, at its surface, and inside the molten aluminum bath, as well as the net downward force acting on the compact. In addition, the exothermic behavior of these compacts was also investigated in an argon protected atmosphere. The temperature rise inside the compact increases significantly with the mass ratio of zirconium in the compact and to a lesser degree with the aluminum bath temperature. Experimental results on the recovery of these compacts in molten aluminum will also be presented.

Jan 1, 2008

By O E. Weightman

This paper describes the methods used for the ventilation of raises, sublevels and drawholes at Cominco&apos;s Sullivan mine. The problems involved in ventilation during blasting, drilling and scraping operations are first re-viewed, and then the air mover, a piece of equipment developed at the Sullivan mine, is described. The design of this device is discussed, along with the operating procedures used. Some figures are given to show the effectiveness of the method. THE Sullivan mine, located at Kimberley in the southeast corner of British Columbia, is owned and operated by The Consolidated Mining and Smelting Company of Canada Limited. Current daily production is approximately 10,000 tons. The mine is developed by sixteen levels over a vertical range of 2,000 feet. The total ventilation requirements, which amount to approximately 1,000,000 cubic feet per minute, are handled through a network of fresh air intake and foul air exhaust circuits. In addition to the many development and production headings, there are three crushing chambers and an extensive conveyor system which must be ventilated.

Jan 1, 1965

By K. K. Feng

"Spontaneous combustion has always been a problem in coal mines and is identified mainly with the mining of low-rank coals. The liability of coals to spontaneous heating is only one of the factors in determining whether spontaneous combustion will occur. However, knowledge of the relative oxidizability of the coal is a useful factor to take into consideration when selecting new coal seams and mining methods for future mine development.Four methods (static isothermal, ignitability, adiabatic and dynamic) have been used to compare the relative liability of Canadian coal to spontaneous combustion and to investigate the mechanism of spontaneous combustion of these coals. Among these f our methods, the static isothermal method is considered to be the best indicator of the susceptibility of various coals to spontaneous combustion. Western mountain coal adsorbs more oxygen and has a higher tendency to undergo spontaneous combustion than the Harbour seam coal of Nova Scotia. It has also been observed that a higher methane content in coal will indicate a lower liability to spontaneous heating."

Jan 1, 1985

By R. B. Roberts, A. L. Mular

A simple way to determine the IEP of oxide minerals is described. The method is shown to apply for fine powders of Fe203 and ZnO. The IEP lies at pH 6.95 for Fe203 and at pH 9.08 for ZnO.

Jan 1, 1966

By L. Paulino, C. E. Zangiacomi, J. Yamamoto

"This paper presents the learning from Alcoa Po9os de Caldas Smelter in Brazil, after several energy restrictions resulting from the failures of three rectifier units at its power switchyard. Starting on December 27th, fuses and diodes failed in three rectifier units of Potline #1, causing a long and dangerous power interruption. Even after current was reestablished, amperage was only 70% of the line target leading to a bath freezing process that lasted for around 48 hours. The process engineering team played with several potroom parameters as pot resistance, bath and metal levels, alumina feeding and bath chemistry in an attempt to minimize impact on the potline metal output and energy consumption. As it will be illustrated, the first battle was to keep the pots running on a ""survival"" approach. After that, several changes took place on the procedures used to run at reduced current which were considered rather successful. Finally, some recommendations will be given to foresee and prevent transformers and rectifiers from undesirable failures."

Jan 1, 2006

By W. G. Jeffery

"The mining and mineral industries have been, and remain, a major component of the Canadian economy. There are approximately 560 producing mining establishments of which there are some 130 metal mines and an equal number of non-metal mines, the balance being quarries for stone, sand and gravel. For 17 metals and minerals, Canada ranks within the top five as a world producer. There are 29 metallurgical plants. Employment in mining, smelting and refining was about 150000 in 1990. Mineral production, including coal, is about $20 billion. Exports up to the metal stage amount to $15 billion providing a positive trade balance of some $10 billion.The producing industry has a wide diversity of products. The companies range from small single mining operations to large multinationals. In terms of technology the industry has always been in the forefront of cost-effective practice, either using home-grown innovation or freely importing technology from around the world,The Mining Industry Technology Council (MITEC) makes an annual survey of the exploration and R&D expenditures of the senior mining industry that is the mining companies that are involved in mineral production from their existing mines. It does not include those companies solely involved in exploration using funds raised through equity sales.Table 1 shows the actual R&D and exploration expenditures as a per cent of sales. R&D shows a rising trend since 1988although the drop in value of output due to lower prices must be recognized as contributing to the increase. The point about this compilation is that the mining industry re-invests some 4070 of its sales in both exploration and R&D in order to sustain itself. Exploration for the renewal of metal inventories for future mining is a process unique to mining. It is not classified as R&D, and the necessity for this investment goes unrecognized by those who state that the industry does not do enough R&D."

Jan 1, 1993

By E. A. Hart, J. E. Gill

"The property of Arntfield Mining Corporation, formerly Arntfield Gold Mines, Limited, covers an area of 2,110 acres and lies in Beauchastel township, western Quebec. The Francoeur mine lies to the west, and to the east are the West Wasa and Wasa Lake properties.The property was staked in September, 1923, by the late F. S. Arntfield. The early surface work was concentrated in the west part of the property along the Francoeur-Arntfield shear zone. The zone was opened by No. 1 shaft, which was sunk for an inclined depth of 250 feet. A series of silicified lenses were discovered farther east, where No. 2 shaft was later raised to the surface. A third shaft explored a shear zone about 1,900 feet to the east, where No. 3 shaft orebodies were developed.The mill was built at No. 3 shaft and production commenced in July, 1935, at 125 tons a day. This was increased to 280 tons by 1938, and later to 350 tons. The mine continued operations on this scale until April, 1942, when the exigencies of war necessitated closing. The Company was reorganized in 1944 and underground development was resumed in June, 1945. The total value of gold and silver produced to April, 1942, was $2,011, 755 from 529,987 tons of ore.ROCK TYPESThe area is underlain by highly deformed and altered Keewatin volcanics overlain by little deformed Cobalt sediments along the south boundary. The lavas in the vicinity of the mine workings are rhyolite, trachyte, andesite, and a flow breccia of intermediate composition. The fragmentals range from fine, well-bedded tuffs to coarse agglomerate in which acidic and basic horizons can be distinguished.The intrusive rocks are diorite and quartz-feldspar porphyry in the form of stock and sills, and narrow dykes of mica lamprophyre and syenite porphyry."

Jan 1, 1954

By C. D. M. Chisholm

Introduction The Sullivan orebody is a sulphide replacement deposit in beds of argillaceous quartzites. The general strike of the vein is north and south, with rather an abrupt change to northwest in the north limits, and a pronounced steepening of the dip in the same area. An east-west section across the orebody in the vicinity where the change in strike occurs will show the dip-to the east-to be about 10° to 20° above the 4500 level, 20° to 30° between the 4500 and 3900 levels, and 35° to 45° between the 3900 and 3500 levels. It is this last section, averaging 75 feet in thickness, that is being mined by the blast hole method discussed in this paper. Typically, the mineralization throughout this section follows the same general pattern between footwall and hanging-wall, there being solid sulphides for a width of 30 to 50 feet, above which lie quartzite beds of varying widths separated by ore bands which also vary in width and in grade. This banded part of the vein usually extends for 30 to 40 feet above the solid sulphides, with commercial ore terminating on reaching a siltstone bed. Development is generally carried to the highest ore band which, when averaged with the underlying quartzite band, will assay about the marginal limit in lead and zinc. When wide stopes are opened, sloughing to the siltstone usually occurs and, although the values are too low to carry the cost of developing and mining, the caved muck can be handled profitably with only haulage and treatment to be considered.

Jan 1, 1946

By D. A. Riva

"The Line Creek Project is located in southeastern British Columbia, approximately 25 kilometres north of Sparwood. The design is to produce a total of2.7 million tonnes of coal annually. This is made up of1.4million tonnes of thermal coal and 1.3 million tonnes of metallurgical coal.Construction commenced in the spring of 1980 and mining operations began in July 1981. The thermal processing plant, maintenance and dry facilities, as well as extensive road and bridge construction, were completed in early 1982. A collective agreement was signed with the International Union of Operating Engineers, Local 115, in June 1981.The first unit train left Line Creek on February 18, 1982 with a load of thermal coal bound for the Ssangyong Corporation in Southern Korea. It was the start of a ten-year contract to supply 350,000 tonnes annually to fire their cement kilns. Additional contracts for 750,000 tonnes will fuel the boilers of Korea Electric Company&apos;s San Chon Po and Go-Jeong power stations. Metallurgical coal shipments are scheduled to leave the Roberts Bank port in Vancouver in April 1983.Tracking an introductory presentation given at the 1981 CIM Annual General Meeting in Calgary, this paper highlights the salient developments by which ""The Line Creek Project"" has progressed during the past year to the"" Line Creek Operation"". Line Creek has com e on stream as scheduled and will meet all contractual commitments pertaining to timing, volumes and quality for thermal coal. The first train load left the plant in mid-February, and the first boat load to Korea departed Roberts Bank in mid-April. Metallurgical coal deliveries will commence in April 1983."

Jan 1, 1982

By P. J. Poirier, J. A. Meech, H. Raabe

"An Expert System has been implemented to assist operators in applying knowledge about froth conditions in the control of the flotation circuit at Highland Valley Copper. For some time, the personnel at Highland Valley Copper have recognized that froth type is a useful indicator of good operating conditions. However, the operating strategy based on froth type recognition is an ad-hoc skill in which different operators use a variety of terms, features and procedures to identify and solve problems. The first phase of this project developed an on-line consultative system to advise and tutor so that the diffuse expertise could be rationalized and consolidated into a standardized format.The second phase has brought this knowledge into a real-time environment to advise the operators on the floor in identifying froth types and troubleshooting corrective action. This paper describes the steps taken to acquire the knowledge, to design the required system features and to implement the real-time version of this system.INTRODUCTIONThe use of expert systems in the mineral industry has been gaining popularity in recent years. Minnova Inc, Les Mines Selbaie, Wabush Mines, Potash Corporation of Saskatchewan are just a few examples of Canadian mining companies that use expert systems to monitor or control their plants. Applications in the field of flotation include Brenda Mines (Edwards, 1992), Mt Isa Mines Ltd (Lacouture et al, 1991), Outokumpu (Karhu, 1989) and Kidd Creek (Burrows et al., 1989).Expert systems are defined as ""computer systems that apply reasoning methodologies on knowledge in a specific domain in order to render advice or recommendations much like a human expert"" (Turban, 1988). The main areas of application are diagnosis, training, process monitoring and control, and design. There are basically two main types of expert systems: Consultative systems, which are off-line applications in diagnosis and design, and on-line realtime systems, used for supervisory process control and real-time advising."

Jan 1, 1993

By D. Markwart, B. Volk

Anode effects are a phenomenon of the aluminium electrolysis process which produce potent greenhouse gases called PFCs (CF4, C2F6). With concerns surrounding global warming, and increasing regulation of GHG emissions, anode effects have become a significant sustainability issue for aluminium producers. In modem smelters, sophisticated computer control and automated alumina feeding systems allow for very tight control of the alumina concentration in the electrolyte and thus very low anode effect frequencies. Older smelters, however, do not have these systems and must either invest heavily to obtain them, or find other, innovative ways to reduce anode effect frequency. This paper will present the integrated approach to anode effect reduction used in the Vertical Stud Soderberg (VSS) potlines at Kitimat Works. Through an innovative combination of simplified signal analysis, modified alumina feed control logic, anode effect prediction, and anode effect prevention using a pager based communication system, Kitimat W arks has been able to make significant reductions to its anode effect frequency.

Jan 1, 2006

By Larry T. Yano, Gerald T. Handford

"Tailings Engineering has the responsibility for planning and coordinating tailings disposal and for ensuring the stability of the tailings dyke. The inclusion of both the planning and geotechnical functions in one team has resulted in greater efficiency in the design and planning process. Major challenges in tailings disposal facing Syncrude are in the areas of: (1) sludge disposal; (2) instrumentation and monitoring; and (3) liquefaction. Meeting these challenges will have a significant effect on the cost effectiveness and reliability of the mining operation.IntroductionThe size of the tailings disposal operation has led to the establishment of a large engineering team devoted solely to the disposal of tailings. This paper discusses: the tailings disposal operation, the role of tailings engineering, the organization, inter faces, and the present and future challenges with respect to tailings disposal."

Jan 1, 1990