Search Documents

By A. Bauer

This paper describes the trends in recent years in explosives formulated to produce larger blast-hole spacings and over-all lower drilling and blasting costs in hard formations. A consideration of current rotary drilling costs per ft of hole and per ton of muck versus hole diameter indicates that it is now possible that we shall see much further use of lower-energy-content, lower-cost slurries and dry mixes, and larger-diameter and, in many instances, cheaper blast holes. These will be drilled on current or slightly larger blast patterns to yield the same energy input per ton of rock and similar fragmentation at lower costs.

Jan 1, 1968

By M. Dupuis

It has been previously demonstrated [l] that there is no obvious thermal balance related issue limiting the size of a Hall-Héroult cell. Yet, it is well known that a forced-air sidewall cooling system is part of the AP50 cell design [2], In the present study, the authors analyze the impact of thermal loading on the mechanical deformation of high amperage cell potshells. The effect of adding cooling fins or a forced-air sidewall cooling system is then assessed.

Jan 1, 2005

By A. Bauer

The correct application of large crater blasts in unfrozen tar sand is an effective means of resisting frost penetration during winter. This results in much higher productivity and considerably less down time with excavators during winter operations. The resulting flatter angle of repose of the highwall has readily been accommodated with slight modification to bucket-wheel excavator operating procedure. Other mining schemes call for large draglines to be located on top of the highwall, which can be as high as J80 feet. The question now arises as to the effect that blasting might have on the stability of such a situation in which the highwall includes potential planes of weakness. This paper applies blast vibration data from large-scale blasting in tar sand to the stability analysis for typical production situations likely to be encountered and indicates safe scaled distances to be employed between dragline and blast.

Jan 1, 1979

By C. Hu

A MOS capacitor hydrogen sensor array is reported for hydrogen gas distribution mapping. Si(100) was used as substrate for film deposition. After silicon oxide growing on the silicon surface with dry thermal oxidation, palladium film was sputtered on silicon oxide as hydrogen-sensitive gate material in MOS structure. The 3x3 sensor array was patterned on silicon substrate and packaged in one chip. Sensors' response was test with impedance analyzer. The sensors in array were calibrated in the hydrogen concentration range from 10ppm to 10000ppm. The 2D hydrogen concentration distribution was obtained with the calibrated sensor array.

Jan 1, 2005

By Naizhong Xu

During the past 30 years, fully mechanized caving mining has played a positive role in the improvement of the efficiency of coal production, but which has also had a great influence on the mining environment, especially to environment damage of shallow mining areas in the central and western regions of China. The surface subsidence parameters are the basis of the surface environment evaluation and governance. During 1980~1990s of the last century in China, fully mechanized mining subsidence laws were researched more fully, however, since coal caving technology is affected by many factors, and researches on its mining subsidence laws (parameters) were found to be grossly inadequate. Through actually observed in recent years, it is considered that coal caving mining subsidence laws (parameters) can use fully mechanized mining law (parameters) for reference. Based on fully mechanized mining laws (parameters), this paper reveals the similarities and differences of the surface subsidence laws between fully mechanized caving mining and fully mechanized coal mining, which can guide the work of coal mining under buildings, water bodies and railways in new mine area and mine collapse governance.

Aug 1, 2013

By Rui Wang, Engang Wang, En Jiang, Anyuan Deng, Xingwu Zhang, Fei Wang

In this paper, the rectangular strands of Incoloy 800 superalloy were fabricated with a pilot vertical continuous caster in Northeastern University, China. In the processing, an electromagnetic stirring (EMS) is applied on the secondary cooling zone to control the solidifying structure and segregation of elements in the strands. The solidification structure of Incoloy 800 superalloy strands were investigated at different electric parameters and casting parameters. The research results show that the EMS can effectively restrain the dendrite growth and increase the ratio of equiaxed grains in Incoloy 800 superalloy strands as applied a suitable electric parameters and cooling condition in the process of continuous casting. The evolution of dendrite crystallization in Incoloy 800 alloy strands from the surface to its center during the solidifying process was investigated with and without EMS.

Jan 1, 2014

In this study, flotation of fine galena, chalcopyrite and pyrite was performed after grinding with different extent of oxidation-reduction condition adjusted by grinding media. Sodium dithionite and iron ions were added in mill to simulate pulp potentials and iron oxidation species produced by grinding media, respectively. The types and quantities of the metal oxidation species on mineral surfaces were determined by EDTA extractions, while the surface electrical properties of minerals and interaction of different types of metal oxidation species were studied by zeta potential measurements. It was found that the nature and concentration of the absorbed metal oxidation species were dependent on oxidation atmosphere controlled by the iron amount of grinding media. These species interacted with each other and had an important role in determining flotation of fine galena and chalcopyrite as well as activation of fine pyrite by lead and copper.

Jan 1, 2006

By D. Nie, M. Ren, T. Mo

This paper studied the phenomenon of room temperature creep deformation at crack tip and its effect on fatigue crack growth rate of a X-70 pipeline steel using compact-tension (CT) specimen on a MTS 810 testing machine. Time-dependent deformation at the crack tip under constant load was observed in this steel at room temperature and the amount of deformation produced was seen to depend on loading rate and the magnitude of stress intensity factor. It is found that there exists a critical stress intensity factor below which the deformation decreases with time when the applied load remains constant. It is also found that the occurrence of room temperature creep obviously affects the subsequent fatigue crack growth rate. The observed behavior was explained based on dislocation theory.

Jan 1, 2005

By Ross I. Kelly

Carbonate rocks are widespread throughout Ontario and provide raw material for more uses than perhaps any other rock type. The principal carbonate rocks that are used by industry in Ontario are Paleozoic era limestone and dolostone. Limestone is a sedimentary rock that is composed mainly of the mineral calcite (CaCO,) while dolostone, also a sedimentary rock, is composed mostly of dolomite [CaMg (CO,),l. The majority of the province's limestone and dolostone extraction occurs from Paleozoic era rocks located in southern Ontario. Calcite and dolomite are also found in Precambrian marbles, calcite veins and carbonatites, however, utilization of these rocks by industry has been less common. Calcite and dolomite-rich rocks are utilized for a wide variety of uses including raw materials for cement and lime manufacture, chemical and metallurgical stone, fillers and construction aggregates (Derry, Michener, Booth and Wahl and OGS 1989a). For some uses chemical and physical requirements are very important. In the manufacture of glass, for instance, the chemical requirements of source materials are very important and very stringent. In other uses physical criteria such as whiteness may be more important. Although carbonate rocks are quite plentiful within the province, deposits that contain high concentrations of calcite or dolomite are somewhat limited. For that reason, this paper focuses on deposits that are known to, or may contain, a high percentage of calcite and/or dolomite. The paper emphasizes potential sedimentary limestone and dolostone resources, as these are the carbonate rocks most commonly utilized by industry in Ontario.

Jan 1, 2001

By A. Plumtree

The morphology of environmentally assisted cracks in stressed pipeline steel has been investigated. For a dilute and neutral solution (NS4) simulating ground water in contact with the steel, semi-elliptical cracks grow faster on the surface (2c) than in the depth (a), hence, the aspect ratio (a/c) decreases. This is explained using a deterministic concept since corrosion is dominant and the primary constraint is the conservation of charge. By contrast, when mechanistic conditions prevail, significant growth occurs in the depth. When underloads are imposed in the loading history, temporary accelerations in crack growth occur because corrosion rather than mechanical effects become dominant.

Jan 1, 2005

By Jean-Louis Robert

Field work inaugurated in 1962 in the townships of Lemieux and Lesseps, in the Gaspe Peninsula of Quebec, has permitted the author to delineate the lithologic units of the area, to elucidate a few stratigraphic problems and to outline several zones of alteration. Certain features of these zones and the numerous mineralized showings in the area merit the attention of prospectors and exploration companies.

Jan 1, 1966

By H. Utsunomiya, Mehdi Sanjari, Abu Kabir, Steve Yue, Jing Su, L. Kestens, In-ho Jung

The microstructure and texture evolution of low temperature rolled AZ31 magnesium alloy during annealing were investigated. The specimens were rolled at the temperature of 100? at a high rolling speed of 1000m/min with a reduction of 30% in one pass. Annealing was conducted at various temperatures ranging from 200? to 500? for different time. To study the effect of fast speed rolling, the same annealing procedures have been applied for the specimens rolled at a significantly lower speed of 15m/min. The microstructure was characterized by optical microscopy and scanning electron microscopy, while the texture was analyzed by X-ray diffraction analysis and electron backscattered diffraction analysis. Texture weakening occurred during annealing at both fast and slow rolling speeds. However, at the same annealing condition, fast rolled specimens always had weaker intensity of basal texture than slow rolled ones.

Jan 1, 2014

By Alessandro Navarra, Kristian Waters

Mineral concentrators are designed from preliminary geological data, and are therefore subject to geological uncertainty. This uncertainty has a demonstrable impact on the mining lifecycle, and has motivated stochastic strategic mine planning algorithms. The current paper describes how these algorithms may be extended to consider mineral processing operations in conjunction with open-pit mining operations. In particular, the paper describes an effective way to incorporate variable concentrator feed grade into these algorithms, which is the first step toward more elaborate representations of mineral concentrators. The resulting framework will be able to connect geological data to alternate configurations of the downstream resources, hence comparing the benefit of each configuration, and the corresponding capital investments. Sample computations are presented, comparing the NPV and utilization for several different mineral processing capacities.

Jan 1, 2015

By R. Bruce Graham

The formation, evolution and classification of peat bogs is discussed. Factors resulting in the internal and external morphological changes in a bog are described. The fibrous, absorptive and sterile properties of peat moss account for its widespread use in horticulture and related fields. These properties also account for its usefulness as a binder in pelletizing, as an insulating material in bat tons and in panel construction. Peat, the humijied product of peat moss is used in market gardening and sod growing. It is utilized in Europe as fuel. It is a source of activated carbon and gas. Potentially peat can be used to produce waxes, resins, tannins, cellulose, hemicellu/ ose, humic acids, lignin and hymatomelanic acid. At present other cheaper sources are available.

Jan 1, 1984

By Kevin Ross

Feasibility Study Team Processing / Engineering?Hatch, Vancouver Mining / Reserves?Australian Mine Consultants, Brisbane Geology / Resources?Roscoe Postle Associates, Vancouver Environmental / Permitting?Rescan, Vancouver Tailings BGC, Kamloops Probable Mine Components Mining tending towards caving methods Underground mine accessed by shaft /conveyor & decline Processing plant producing copper concentrate containing gold Concentrate trucked to rail head for export Non saturated tailings disposal

May 1, 2006

By M. Bozorgtabar

Metal Matrix Composites (MMC) have a ductile matrix containing ceramic particles, Due to their improved wear properties, Al?SiC composites have economical applications in many industrial uses where wear is a problem, One of the most serious difficulties in manufacturing Al-SiC composites is obtaining adequate 'wetting' of the particles by the melt. In this research work, a stir casting system was designed for the improved manufacturing Al-SiC composites, The effect of some production variables such as the addition of SiC particles to the aluminum melt on wettability, was also studied. The results showed that the manual addition of particles would not be successful in manufacturing and that a system of adding silicon carbide particles through controlled temperature, atmosphere and improved mixing was needed.

Jan 1, 2005

By O. P. Garg

Based on improved methods of collection and analysis of geotechnical data, slope angles have been steepened in some mines of the Iron Ore Company of Canada at Schefferville, Quebec. This paper describes the slope design case history for Fleming NO.3 mine and illustrates the application of modern techniques. The new design has resulted in significant financial savings due to a reduction in required waste stripping.

Jan 1, 1978

By J. E. Udd, L. B. Geller

"Responding to requests by the Canadian mining industry and the mine regulatory authorities, the Canada Centre for Mineral and Energy Technology (CANMET) undertook a major research project on evaluation of wire rope testing in 1986. The objectives were to document, analyze, and clarify - in basic operational terms the reasons for ongoing mine shaft wire rope failures that occur despite mandatory non-destructive testing (NDT) with electromagnetic (EM) instruments on a routine basis.The project's investigative scope and depth was unprecedented. It could not have been successfully completed without the wholehearted cooperation of industry, research organizations, and mine-inspectorates at both national and international levels.The project's goals were attained. II was shown that, at present, the problem areas in Canada are oj a human , rather than of a hardware-related nature. Consequently, the principal recommendations are concerned with a more widespread, more uniform and thorough operator training and certification process at industrial and regulatory levels. Secondary suggestions concern areas of hardware-related improvements.In this paper an up-to-date general overview is given of the major project results. A n extensive reference list is also provided of papers that contain all relevant documentation in detail."

Jan 1, 1992

By D. P. Ziegler

Formulas relating economic optimum busbar cross sectional areas to busbar cost, electric price and financial parameters are reviewed and revised. Application of the formulas is illustrated with discussion of the appropriate choice of parameter values and the sensitivity of the optimum to the parameters. The extension of the single busbar concept to optimization of more complicated arrangements of bus for smelting pots is complicated by the constraint of obtaining a specified current distribution. An example problem illustrates the optimization of a section of a bus network containing a fork, with the imposed limitation of achieving a specified uniformity in the current. In cases where the current in the individual conductors may vary, Kelvin's law does not apply. Further extension of the technique to a full pot set of conductors poses additional problems which are discussed, but whose solution has not yet been accomplished. Aluminium 2006 45th Annual Conference of Metallurgists ofCIM Montreal, Quebec, Canada Edited by

Jan 1, 2006

By M. Scobie, T. Atkinson

"This paper reviews the development of new designs in extensible and high angle conveyor systems. These aim to overcome the limitations of prior alternative concepts in design. The application of such systems in strip, terrace, open pit and mountain mining is reviewed. IntroductionTruck haulage costs have tended to escalate in recent years. This has been primarily due to operations generally moving to greater depths with associated increases in haul distances . Periods of high inflation rates have also been experienced for diesel fuel oil, tires and other petroleum based products. Recent international political events have tended to regenerate concerns over future oil supply and price stability. For such reasons, conveyor based transport is becoming increasingly attractive. Truck haulage maintains an inherent flexibility and improvements continue to be made in performance and capacity. Doubts must exist, however, over the extent to which further economies of scale may be made. Conversely, belt conveyor systems do not suffer this constraint and have the following advantages:• Electrical power is used and the specific energy consumption is at least half that required for truck haulage.• Operating costs and skilled labour requirements are lower.• Equipment has superior longevity and is ""inflation proof"" .• Access roads can be steeper and narrower in most mine environments, reducing construction and maintenance costs.• They are less prone to breakdown and bad weather delays .• In long haul, high capacity operations conveyors can save substantially on capital cost.• Environmental impact is improved with reduced noise level, dust and atmospheric pollution. Although conveyor systems are less flexible in operation than truck haulage and although a breakdown in any part of the system can immobilize the total system, mechanical availabilities of + 80% are constantly reported by large operators. There would appear in the past to have been some prejudice against conveyor systems in hard rock mines due to lack of experience. Apparent reservations would apply equally 10 underground coal mines, yet practically all of these mines (and some underground hard rock mines) find conveyor systems more economical than other transport systems."

Jan 1, 1991