Search Documents

By S. R. Gilbert, C. O. Bounds, R. R. Ice

"Many ores are upgraded to produce auriferous sulphide concentrates (principally pyrite) which are not amenable to direct cyanidation. Often these refractory gold-bearing concentrates contain undesirable elements such as arsenic, antimony, etc., which present environmental and/or processing problems. The pretreatment techniques most often considered for processing these concentrates prior to cyanidation include roasting, pressure oxidation, chemical oxidation, pre-aeration, and recently, bacterial oxidation. In this paper, the technical performance and economics of bacterial pre-oxidation vs the classical roasting approach for treating a specific auriferous pyrite concentrate are compared. The results provide flow sheets, preliminary operating and capital cost estimates, and rates of return for the two processes and demonstrate the potential advantages of bacterial pre-oxidation. IntroductionThe increased attention that gold has received in the last ten years has prompted mining companies to look for lower grade orebodies. Many of these low-grade ores do not respond well to conventional direct cyanidation recovery techniques. As free-milling ores decline, gold is sought in refractory environments which, ultimately, drive up the treatment costs.There are a number of reasons for a gold ore to be termed refractory, most of which can be identified by thorough mineralogical examination. The mineralogical occurrence of gold can, to a great extent, impact the method by which the ore is treated and, consequently, the capital and operating costs. Gold in a refractory ore can often occur as discrete particles locked in a host of silicate or carbonate gangue, or associated with sulphides or sulphosalts. Depending on its particle size, gold can be liberated and recovered by mechanical size reduction such as regrinding. This approach is most effective for gold in the 10 - 50 micron range. Gold can also be associated with clay, iron hydroxides, or other minerals which tend to coat the gold surface and inhibit the penetration of the cyanide solution, resulting in poor plant recovery. Because of their resistance to cyanide dissolution, gold tellurides and other refractory gold minerals are also responsible for losses to the tailings. For these reasons, it is paramount that the mineralogical occurrence of the gold be thoroughly and accurately determined before selecting a final process flowsheet."

Jan 1, 1988

By Eric Bain Wasmund, Lance Christodoulou, Julio Jairo Carmona Franco, María Fernanda Castillo, Jose Concha

"A number of technologies are in practice for selectively removing coarse gold from conventional grinding circuits. These circuits are often designed so that the grinding mill output is size classified, with large (or high density) particles being removed before the tails are returned to the mill. Because of the high relative SG of gold, and the fact that some forms of gold such as free gold do not break apart during conventional grinding, coarse gold can accumulate in the circulating load, and eventually be lost.Eriez has developed a flotation cell that uses fluidized water to enhance flotation of coarse particles. More than 40 units have been sold in industrial minerals, and we are now exploring applications for the HydroFloat® in the gold industry.Mineros S.A currently produces approximately 120,000 oz of gold per year by gravity concentrating alluvial gold ore with a mean particle size of 330 microns, followed by further concentration using a Falcon separator. A 400 mm diameter pilot-scale HydroFloat® was added to the tails of the Falcon to test whether additional gold could be captured. Enrichments of 50-600 times and recoveries normally in excess of 95% were achieved. This allowed direct smelting of the gold concentrate. Metallurgical results and operating parameters such as water addition and power will be discussed during the presentation.This result opens the possibility that the HydroFloat® could be used directly in the grinding circuit, for removing coarse gold in the circulating load. This work also shows the possibility that the HydroFloat® can produce a throwaway tail, which will reduce the size of the circulating load stream and the grinding requirements of the circuit."

Jan 1, 2015

By Diankun Lu, Ganfeng Tu, Edouard Asselin, Feng Xie

A novel separation process for detoxifying cadmium-containing residues arising from zinc hydrometallurgical processes has been developed. An initial investigation indicated that a high concentration of zinc in the sulfate solution can be effectively separated from cadmium by solvent extraction with P204 (di(2-ethylhexly)phosphoric acid, D2EHPA). The mixture of sulfuric acid and ammonium citrate ((NH4)3C6H5O7) is thus used to extract metals from the residue at room temperature. Copper in the leachate is recovered by solvent extraction (SX) with LIX 973. Cobalt in the raffinate from the copper SX process is recovered by precipitation with a-nitroso-ß-naphthol. The results show that more than 50% of the copper and virtually all the zinc, cadmium and cobalt in the residue can be leached under the experimental conditions used here. Virtually all dissolved copper and cobalt can be recovered in the subsequent solvent extraction and precipitation processes. The presence of (NH4)3C6H5O7 could significantly facilitate the extraction of zinc by D2EHPA in the subsequent separation of zinc and cadmium. More than 97% of the dissolved zinc can be recovered through a two-stage counter current solvent extraction process. After separating copper, cobalt and zinc, cadmium can easily be recovered from the solution either by cementation with zinc powder or by electrowinning, while the purified solution can be recycled back to the leaching process.

Jan 1, 2014

"The Antamina orebody is a geologically complex, polymetallic skarn located in the Peruvian Andes. A range of copper and copperzinc ores are campaigned separately through the concentrator producing copper and zinc concentrates as well as lead and molybdenum by-products.Ore type classification at Antamina is based on chemical assays; geological or lithological variations are not considered. Consequently, each ore type demonstrates a wide range of concentrator performance.Antamina is currently implementing a system to track ore movements from the shovel face to the concentrator. Relatively sophisticated models of run-of-mine and coarse ore stockpiles ahead of the mill will be used to account for the variable delay between mining and milling.One of the numerous benefits of ore tracking is the ability to directly associate the measured concentrator performance with a physical location in the orebody. Using existing mine planning software, three-dimensional models can be created of such performance measures as metal recovery, concentrate quality, operating cost, and reagent consumption.Such a database of information allows the true value of different ore sources to be determined. The value of an ore source is conventionally measured as metal content (individual or combined ‘equivalent’) with a cut-off grade applied to indicate some base level operating cost. However, the true value of an ore source should include dynamic factors like haulage cost, reagent use, smelter penalties, and even prevailing metal prices. If an ore source is considered from all perspectives rather than simply its potential to deliver value, the concept of ore becomes more flexible. Any ore source that reveals itself to be unprofitable can be eliminated from the mine plan or possibly blended with others to improve its value. The ability to predict mill performance, and thereby profitability, is a powerful tool.In an operation such as Antamina, where managing ore sources, campaigns, and the delivery of a variety of concentrates in a narrow timeline to customers is a daily challenge, prediction is the key to success and improved efficiency."

Jan 1, 2005

Many mines in Canada, the US and S. Africa are reaching the hoisting limit. Very little payload will be possible without compromising safety due the excessive weight. It has been suggested (DeLorme, 2000), that one of the most attractive concepts to enable deeper hoisting is to reduce the allowable factor of safety in the wire rope. Researchers at the Spokane Research Lab are developing new technology to improve hoisting safety and productivity by providing new monitoring and analytical tools. A Shaft Conveyance Monitoring System (SCMS) has been developed which determines hoist rope end load, true conveyance position and acceleration, and rope safety factor, as well as other hoist operating parameters. This information is transmitted to the hoist operator display 20 times per second. Recent field measurements on 45 mm(1 ¾ in.) diameter hoist rope indicate that dynamic forces during loading of a 9000 kg(10 ton) skip may exceed the safety factor of the rope. To improve on the current understanding of the mechanical behavior of hoist ropes, and to help interpret the results from field-testing of the SCMS, a new approach to computer modeling of stranded wire rope is also being developed. Particle Flow Code, PFC3D (Itasca 1995b) is used to simulate the structural behavior of wire rope and the interaction between individual strands when the rope is subjected to static and dynamic end loading. Details of the SCMS, field results from the measured rope loads, and the results of numerical modeling on the wire rope will be discussed.

May 1, 2002

By Brad Simser

The Brunswick No. 12 Mine is a 10 000 tonne per day producer of lead-zinc-copper-silver ore that has been in operation since 1964. Mining of this multiple lens deposit is primarily by blasthole stoping techniques between 400m and 1200m below surface. The combination of a high overall extraction ratio and high horizontal stresses (twice the vertical) has elevated the induced stress regime to levels comparable to much deeper operations. Improved mine design, and a better understanding of how the rock mass responds to mining in high stress environments is essential to improve overall recoveries and maintain safety. Seismic monitoring has proven to be an essential tool at Brunswick, for both short-term safety of workers, and long-term strategic planning. Practical case studies illustrate how seismic data, particularly source parameter information, can be used to measure the rockmass response to mining and improve mining layouts in difficult regions. As the global trend continues towards mining in deeper, higher stress environments (e.g. South African Witswatersrand Basin, Sudbury Basin) and as local extraction and thus ground stresses continue to increase in existing deposits, seismic monitoring will play a critical role in mining safely and economically.

May 1, 2003

By Paul Grady, Martin Froehling, Curtis Mohns, Eliab Roman

"Since the idea of processing rock to unlock the valuable minerals inside was put into practice, efforts to improve production began. Methods have been learned that allow for operation in environments and under circumstances where it would not have been possible until now. All existing operations have experienced at least some form of productivity improvement measures. The objective is simple: generate more product of better quality in less time and at lower unit cost. Since the year 2000, various modifications have been made at the Kemess Concentrator in efforts to improve productivity. The following is a discussion of these modifications and their contributions to the success of the operation.INTRODUCTIONThe Kemess South Mine, a major producer of gold and copper, is located in north-central British Columbia. Kemess was brought into production in May 1998 by Royal Oak Mines with a modern mill controlled by a fully integrated Foxboro IA DCS system and employing 134 people. On February 11, 2000 Northgate Exploration Limited (now Northgate Minerals Corporation) acquired Kemess Mine from receivership. Since acquisition in 2000, Kemess has seen many accomplishments, including the reduction of costs by 40% site wide.The mill has a nameplate capacity of approximately 56,000 tonnes per day which is processed through a Metso (Svedala) 60” x 89” Primary Gyratory Crusher and then conveyed by a 60” conveyor to a stockpile with 48 hours of total storage capacity. The nominal minus 6” rock from the stockpile is fed to two parallel grinding circuits (A & B). Each section consists of a 10.4 m F x 4.7 m SAG mill with dual drive motors (4,480 kW apiece) discharging onto a 2.4 m x 7.3 m Metso (Svedala) single deck vibrating screen to remove the coarse material for recycle to the SAG mill by a Continental 45º high angle sandwich conveyor. Screen undersize is pumped along with ball mill discharge to a cyclopac consisting of twelve Krebs 66 cm F cyclones to classify flotation feed to a size of approximately 65% minus 200 mesh. Cyclone underflow feeds a Metso (Svedala) 6.8 m F x 11.0 m ball mill, also with dual drive motors (4,480 kW apiece). The primary grinding circuit has 35,840 kW available for grinding."

Jan 1, 2005

By Jonathan Allen, Peter Radziszewski

"Stirred mill technology dates back to 1928 where the idea to use “an agitator and spherical grinding media” was presented. The year 1948 saw the successful application of DuPont’s “sand mill” for pigment grinding. Subsequent years have led to the development of different types of stirred mills spanning a number of industries that require fine and ultrafine grinding. In the context of the mining industry, smaller grain size and other mineralogical characteristics have motivated the need to grind finer. In order to address this need, the interest in stirred milling technologies has grown over the last 20 years as can be illustrated by the large body of literature published over this same period of time. The typical observation reported in the literature is that in certain circumstances stirred milling is significantly more efficient than ball milling. Despite these developments, the tumbling mills are continuing to be used in fine and ultrafine grinding applications. The main reason for this, as communicated at the Canadian Mineral Processors roundtable discussion in 2013, is that the comfort level in understanding stirred milling technologies is not at the level of that of tumbling mills. The aim of this paper is to contribute to increasing the general comfort level with stirred milling technologies by developing a better understanding of how power and energy is affected by stirred mill impellor design and mill operation. This will be accomplished by first completing an overview of the power models found in the literature followed by a general description of DEM and CFD stirred mill models as well as the insights that can be drawn from them. Finally, a generic stirred mill power model will be presented and applied to different stirred mill types in order to develop some insights into the differences between different mill types. The paper will close with a discussion on some of the challenges that these models have and how future research might contribute to overcoming them."

Jan 1, 2014

By J. R. Goode

"The Las Cristinas deposit in Venezuela contains reserves of 12.8 million ounces of gold at a grade of 1.20 g/t (Crystallex, 2004). The deposit comprises fully oxidized saprolite (SAPO) overlying a layer of sulphide-enriched saprolite (SAPS) which lies above carbonateleached bedrock (CLB) and carbonate stable or un-leached bedrock (CSB). Gold occurs at about the same concentration in all lithological groups. The bedrock units contain minor amounts of copper (about 0.1%) as chalcopyrite, while SAPO contains virtually no copper which has been leached and deposited in the SAPS zone.A previous owner began investigation of the Las Cristinas deposit in 1991. Over the next seven years, the company drilled 1,174 holes with a total length of 159 km, conducted extensive metallurgical testwork, including pilot plant operations, and completed feasibility studies. Construction was started in 1997 and again in 1999, however, on each occasion was suspended.Crystallex has been producing gold inVenezuela since the early 1990s. In 1997, Crystallex acquired Inversora Mael which had held two of the claims to the Las Cristinas concessions since 1986. In September 2002, Crystallex entered into a definitive agreement with the Corporación Venezolana de Guayana (CVG) to develop the Las Cristinas deposit.An extensive program of studies and testwork was started in late 2002 to determine an optimum development plan for Las Cristinas. Mine Development Associates, SNC–Lavalin Engineers and Constructors, SGS Lakefield Research Limited, J.R. Goode and Associates, and A. Laplante at McGill University acted as the main contractors.Because of the potential value of by-product copper, earlier flowsheets used carbon-inleach for SAPO, but processed all other ore types by flotation to produce a gold-copper concentrate with cyanide leaching of cleaner tailings to maximize gold recovery. Cyanide recovery was necessitated by the high copper content of the leach feed. Initial studies of available data by Crystallex revealed that direct leaching of all ore types would provide about 11% more gold recovery than the previously selected flotation route with reduced capital and operating costs.Bench and pilot-scale studies have confirmed that a SAG-ball mill-gravity-CIL route is very effective for all ore types and will give about 89% gold recovery. This paper describes the testwork conducted in 2003, discusses a 20,000 t/d plant design, and presents economic data."

Jan 1, 2005

By L. Lui, A. Cauchon, A. R. Laplante

"The gravity circuit at Les Mines Camchib Inc. consists of two pinched sluices to bleed a feed to one of two 76 cm (30"") Knelson concentrator. The Knelson concentrate is upgraded to smeltable grade with a smaller Knelson (18/30 cm) and a riffleless table. Their tails are column cyanided and washed prior to recycle to the grinding circuit. This paper details size-by-size circuit performance. The Knelsons recover around 90% of free gold (as determined by Mozley Laboratory Separator), even below 37 µm. The sluices are ineffective, with upgrading ratios around 2, but approaching unity in the fine sizes. Much of the effectiveness of the circuit lies in the high gold circulating loads in the grinding circuit, which partly atone for the poor sluice performance, and the ability of the Knelsons to recover free gold. Secondary upgrading recovers slightly above 99% of the primary concentrate gold, 90% of it in a 65% Au concentrate and the balance in a heavily loaded (10 to 20 oz/st) pregnant solution. INTRODUCTIONBackgroundThe operating performance of the mill of Les Mines Camchib Inc. has been described earlier (Laplante et al., 1989). The presence of significant chalcopyrite (1 % and up) makes flotation necessary prior to cyanidation, to limit cyanide consumption and minimize environmental impact. In 1982, the presence of very high gold circulating loads in the grinding circuit lead to the commissioning of a gravity circuit, schematically shown in Figure 1. Gravity recovery of gold has been found beneficial because it increases metallurgical recovery by 1-3% (Laplante et al, 1987), as only part of the flotation tail is cyanided, and economic recovery, because of the lower net smelter return of gold in the flotation concentrate (as compared with the gravity concentrate). The latter increase is estimated, with a net smelter return of 95%, at 1.5% when gold recovery by gravity is equal to 30%. In early 1988, a sampling program was initiated to characterize the behaviour of gold in the grinding/gravity circuit. This paper reports on the results of this study."

Jan 1, 1990

By Marcel M. Djivre

Electromagnetic wire rope testing is the only practical non-destructive method to evaluate the current condition of wire ropes in general, and in the mining industry in particular. The method has been successfully used worldwide for decades. In mining it has considerably improved the safety of operations. Yet, problems persist. In particular both the Loss-of-Metallic-Area (LMA) readings, as well as the Local Fault (LF) readings, as obtained by different instrument operators, were found to be unacceptably diverse. Consequently, large sums have been spent internationally, as well as in Canada, comparing a whole range of these instruments in an effort to rate their performance. The published results clearly confirmed operational experience, namely that the LMA and LF readings were, indeed, unacceptably diverse. Excellent pertinent conclusions were also published. In Canada the authors? conclusion was that while the divergence in the LF signal based results could, possibly, be attributed to both hardware and human-error related factors, the LMA signal related quantitative uncertainties were human-error related. Consequently, much attention was paid in Canada to developing novel control methods, namely computerized ones to replace the more error-prone analogue ones. In addition new sensor-heads were developed, both for portable as well as for permanent installation with remote control operations. While these efforts were of considerable benefit, the situation must again be carefully reviewed with very special reference to deep-level mining, now of immediate concern in Canada as well. In this paper the authors supply an overview of the results obtained by three of the four major international projects referred to previously. Relevant conclusions/comments are also restated. Moreover, specific recommendations are put forward as to how current problems might best be remedied.

May 1, 2004

By N. Coli

The exhausted Santa Barbara open pit mine (Tuscany, Italy), owned by the main electric power company in Italy (ENEL S.p.A,) extracted lignite as a fuel for the Santa Barbara thermoelectric power plant. The mining activity led to the excavation of a wide slope (with maximum height of 200 m and a planar extension of about 1300 m x 500 m) in the Shale Limestone Chaotic Complex (SLCC) (Figure 1). Since the beginning of its excavation the slope underwent rotational landslides and diffuse instability phenomena. From a geotechnical point of view the SLCC represents a typical bimrock (block-in-matrix rock) (Medley 1994, Medley 2002, Medley 2007) characterized by a mixture of a highly sheared, scaly-fabric, clayey matrix and calcareous blocks ranging from a few millimetres to tens of metres in size. Since the geometrical properties of blocks (grain-size distribution, shape, orientation and volumetric proportion) have been proved to influence the mechanical behaviour of bimrocks (Lindquist & Goodman 1994, Goodman & Ahlgren 2000, Kim et al. 2004, Sonmez et al. 2006), the aim of the present study is to investigate the geometrical properties of calcareous blocks in order to properly characterize the mechanical behaviour of the SLCC bimrock and to further assess the stability of the slope. Block size-distribution and shape were investigated by means of advanced image analysis techniques of SLCC pictures taken in the field. Geostatistical semivariograms and variographic maps were also used in order to investigate the anisotropy of block spatial distribution. Finally, in-situ large sized sieving tests were carried out to investigate the volumetric block proportion within the clayey matrix.

May 1, 2009

"The mining industry uses many types of mineral and metallurgical plants to produce saleable product from ore mined. Plant design history has left current operations with a mixture of manual operation and various forms of automated process controls. Consequently, we typically see high variability in the continuous operations together with a shortfall in the attainment of full capacity, or higher utilisation of consumables.At a level of best practice, ‘Operational Performance Excellence’ focuses on process control, using automation and control systems to deliver process optimisation. This more sophisticated delivery is a great deal more difficult than the first stage of equipment selection / installation. It includes the appropriate selection of the right instrumentation, control system, key process knowledge, individuals with a solid control engineering background / experience, and the essential backing / support of the operations management team together leading to higher value delivery. Robust solutions can be realised, considerably minimising process variation, thus leading to process optimisation. This approach results in an easier, efficient and safer process while providing considerable returns for the plant owners.How variable are your processes, and do you maintain optimised process performance with dedicated resources, modern instrumentation, ‘best practice’ control systems and performance monitoring tools? In this paper, these questions and their possible answers are discussed."

Jan 1, 2014

By Carlos León, David Estrella, Javier Linares

"Recently, Antamina has completed an expansion program of its operations which increased the thoughput in grinding from acapacity of 109 to 130 ktpd. After commissioning, throughput could be exceeded in grinding and downstream processes but primary crushing became a major bottleneck to the overall production process.With an objective to increase the processing capacity of the primary crusher system, a multidisciplinary team was formed with members of Mine, Concentrator and Maintenance departments, who analyzed the overall context of this process restriction. The main implementations developed were: automatic discharge systems of trucks, logic to count trucks and elaboration of a daily performance report. Following implementation of developed improvements, the numbers of discharged trucks to crusher were increased from 449 to 614 units per day. As a result, the expansion target of 130 ktpd was exceeded and processing capacity was increased from 109 ktpd to 145 ktpd. This improvement adds very significant economical value for Antamina.INTRODUCTIONAntamina is a copper-zinc mine located in the Peruvian Andes. Compañía Minera Antamina is owned by BHP Billiton (33.75%), Xstrata (33.75%), Teck Cominco (22.5%), and Mitsubishi (10%). The mine was commissioned in 2001 with a capital investment of US$2.3 billion, and had a nominal 77,000 ktpd mill capacity. Mining, milling, flotation, and tailings impoundment take place at the mine site, which sits at an altitude of 4,300 m above sea level. The deposit is a polymetallic skarn ore body with intrusive phases of quartz-monzonite porphyry into Cretaceous aged limestone. Copper is present mainly as chalcopyrite with a minor bornite component. Zinc is present as sphalerite. Molybdenum is present as molybdenite. Some lead, bismuth, and silver are associated with the sulphides. The deposit is currently classified into six main ore types [Dechert, 2006], grouped into two categories: copper and copper-zinc. The mill produces four concentrate types: copper, molybdenum, zinc, and lead-bismuth. Copper and zinc, concentrates are transported by pipeline down to the port of Huarmey. Molybdenum and lead-bismuth concentrates are bagged and trucked to port."

Jan 1, 2013

By Kevan J. R. Ford, Chris A. Fleming, Robert D. Henderson

"Kinross Gold Corporation’s Maricunga mine in Chile presents an ideal opportunity to apply the SART process to a heap leach operation. Given increasing levels of cyanide complexed copper in current pregnant solutions from Maricunga heaps (over 300 ppm Cu), there is a need to reduce these levels and decrease cyanide consumption and cost. Additionally, a means of disposing of this copper is required, preferably as a saleable product. The well published SART process applied to gold-copper cyanide solutions was selected as it allows rapid precipitation of cyanide soluble copper as a relatively pure copper sulphide. The process also allows effective recovery and recycle of cyanide back to the heap leach operation.This paper reviews the SART process chemistry and presents a summary of SART bench-scale and pilot plant testwork completed by Kinross. Key design parameters and engineering aspects of the proposed plant at Maricunga are discussed. SART plant operating costs and net revenue analysis are included and illustrate the compelling economics of installing a SART process plant. INTRODUCTIONMaricunga OperationCompañia Minera Maricunga (CMM), fully owned by Kinross Gold Corporation, operates the Maricunga mine (formerly Refugio) which is located 120 km due east of the city of Copiapó at an elevation of 4,200m above sea level in the Andes mountains of northern Chile. Figure 1 shows a map of the location of the Refugio mine relative to other gold and copper mines in the region."

Jan 1, 2008

By Carol E. Jones

Outline ? Reclamation is a primary mitigation. ? Understand baseline environment and land use. ? Determine reclamation goals. ? Selecting reclamation technology. ? Determine technical risk. Reclamation ? Primary Mitigation ? Through land and water disturbance, mining can have significant local and regional environmental impacts. ? Impacts can also result from associated land use changes. ? Reclamation is a primary tool that the mining industry uses to manage its environmental impacts.

May 1, 2008

By Dave Rose, David G. Meadows, Mike Westendorf

"Copper Mountain’s concentrator was commissioned in May 2011. The circuit consists of a 34’ x 20’ EGL SAG mill, a Raptor 900 pebble crusher and two 24’ x 39’6” ball mills. Each mill is equipped with a 2 x 8500 HP dual pinion drive system. The plant was designed to process 1585 mtph of SAG feed. From startup, the mill struggled to meet the required production rates. Over time, a major initiative that involved blasting and fragmentation, optimization of the SAG mill in terms of discharge grates, ball size and slurry density, and operation of up to three mobile pre-crushing plants resulted in significant increases in throughput. In parallel, a number of modeling tools, including JK SimMet, were run based on plant benchmarking exercises. Samples collected at the mine site during ramp up confirmed the very competent nature of the ore with drop weight - A*b values of less than 24 being recorded on a variety of plant feeds and lithologies. After due consideration including demonstration of proof of concept, a new pre-crushing circuit incorporating an XL2000 cone crusher and associated screening equipment was designed, constructed and commissioned at the site in August 2014. This paper reviews the history of the original circuit design, the various optimization steps taken and impacts, together with the final pre-crushing circuit and net results.IntroductionThe Copper Mountain Mine is located approximately 20 km south of Princeton, British Columbia, Canada (refer to Figure 1). The region has a long history of copper mining dating back to 1923. The Copper Mountain camp occurs in the 'eastern volcanic belt' of the Nicola Group (Monger, 1989). It is an alkali copper-gold deposit in which the volcanic strata are intruded by early Jurassic dykes, sills, irregular plugs and zoned plutons (Woodsworth et al., 1992). The stratified rocks are relatively fresh with slight metamorphism in the local contact regions."

Jan 1, 2016

By R. Tessier, C. R. Larsen

"INTRODUCTIONOn November 10, 1982 Nor and a Inc signed an agreement with Golden Sceptre Resource Ltd. and Goliath Gold Mines Ltd. to construct a mine and milling facility.The Golden Giant mine is located in the Marathon area of north - western Ontario, immediately north of Highway 17 and about- 3.5 km west of Highway 614.With the exception of selected unit processes, the mill was designed for a nominal throughput of 2500 tonnes per day with early operating data to be used to identify sections requiring possible expansion to achieve an ultimate throughput of 3000 tonnes per day.Commissioning of the highly instrumented milling complex which includes crushing, grinding, cyanidation, and carbon in pulp processes commenced in February 1985. After water testing various sub-circuits from grinding through tailings, waste ore was introduced to ensure proper mechanical and electrical operation of process equipment.The first ore was milled as a mixture with waste on March 4, 1985. The first gold bullion was poured April 6, 1985.Initially, ore was only available from mine development at a rate of 700 t/d, which was milled at a minimum rate of 1200 t/d. While regular weekly shut downs of two to three days was useful for mechanical maintenance, changes, and modifications, process tuning was more difficult due to the non-steady operation. As increased quantities of ore became available, regular weekly shutdowns tapered off and process operation improved accordingly. For testing purposes and as ore was available, mill throughput was increased regularly to 2300 t/d and for very short periods of time to nearly 3000 t/d.No major design or operating problem has been encountered to date. The following is a brief description of the milling process and various operating highlights. Process flowsheets are shown in Figures 1 through 6."

Jan 1, 1986

By Samuel Frimpong

The interaction of oil sands with a ground articulating pipeline (GAP) system has been simulated with the dynamic model established in this work by combining the multi-body and soil dynamics with the Automatic Dynamic Analysis Mechanical Systems (ADAMS) software. Mathematical models governing the interaction of the GAP system with the oil sand terrain have been modeled based on the theory of multi-body and soil dynamics. These models consist of GAP track-oil sand contact model for generating the contact force between oil sands and track and load-deformation oil sand model for capturing the dynamic behavior of oil sands. A virtual prototype has been created and simulated in the ADAMS environment. The simulation result of the effect of load on oil sand deformation indicates that maximum deformation value increases non-linearly with load varying from 0 to 60t. This study provides a solid foundation for further research and the GAP technology development.

May 1, 2004

By P. Pyykkö, E. Peuraniemi, J. Järvi, P. V. Latostenmaa, V. Törölä, S. Junnikkala

"Nickel concentrate smelting started in Harjavalta in 1959. First, flash smelting - Peirce-Smith converting route was applied, and the high-grade converter matte was further refined to nickel cathodes. In 1995 the original smelter flow sheet was simplified with the novel DON (Direct Outokumpu Nickel) technology. In Harjavalta with the DON technology, high-grade nickel matte with low iron content is produced in flash smelting furnace directly without subsequent converting stage. The metal values in the smelting slag are recovered in an electric furnace as an iron containing bottom alloy. Main special features in Boliden Harjavalta nickel smelter are smelting of high-magnesia concentrates, the high recoveries of nickel and copper, as well as those of PGM`s and cobalt.Sulfur and dust emissions to air can be seen generally as one main disadvantage of nickel smelting operations. In Harjavalta continuous improvements in environmental performance has been rewarded by minimum sulfur and dust emissions to the environment and working atmosphere. Today Boliden Harjavalta’s nickel smelter is presenting state-of-art-technology at nickel smelting.This paper describes the nickel smelter process and includes recent production and emission data. It describes features required to achieve environmental and occupational hygiene goals and compares environmental performance data to that published on other smelting operations. General description of New Boliden Way is presented and a case example of production stability project is also presented."

Jan 1, 2014