Search Documents

By James F. Allan

"The Kipawa yttrium-zirconium prospect is located about 150 km south of Noranda, Quebec. Yttrium-zirconium mineralization occurs in an elongate, regionally metamorphosed and deformed peralkaline complex in the Grenville terrain. The mineralized zone, as defined by =.0.10% Y2O3, is 1300 m long and 10 m to 30 m wide. Zirconium content typically ranges from 0.50 to 1.20% ZrO2, The mineralized zone strikes northwest and dips 20 degrees to 35 degrees to the southwest. It occurs at the structural base of the peralkaline complex in syenite gneiss and calc-silicate rocks and is conformable with both the footwall contact of the complex, and the layering and gneissosity in the enclosing rocks. Minerals of economic interest are eudialyte (sodium-zirconium silicate), mosandrite (sodium-titanium silicate), britholite (calcium-silica phosphate), and a few other uncommon zirconium and titanium silicate minerals.The highest and most continuous yttrium grades occur in the upper part of the syenite gneiss unit in areas containing eudialyte, mosandrite and minor britholite. Yttrium also occurs in britholite in calc-silicate rocks and in mosandrite in syenitic rocks in the lower part of the syenite gneiss unit. Both the yttrium-bearing minerals and yttrium grades are erratic in the lower part of the unit. Zirconium is generally more uniformly distributed than yttrium. A peralkaline granite gneiss phase of the complex intrudes the syenite gneiss and possibly truncates it, and the mineralization, near the southern boundary of the mineralized zone.The mineralized zone is coincident with a radiometric anomaly and discontinuous yttrium and zirconium soil anomalies.More drilling and metallurgical studies will be required to determine the economic viability of the yttrium and zirconium mineralization at Kipawa."

Jan 1, 1992

By James F. Allan

"The Kipawa yttrium-zirconium prospect is located about 150 km south of Noranda, Quebec. Yttrium-zirconium mineralization occurs in an elongate, regionally metamorphosed and deformed peralkaline complex in the Grenville terrain. The mineralized zone, as defined by =.0.10% Y2O3, is 1300 m long and 10 m to 30 m wide. Zirconium content typically ranges from 0.50 to 1.20% ZrO2, The mineralized zone strikes northwest and dips 20 degrees to 35 degrees to the southwest. It occurs at the structural base of the peralkaline complex in syenite gneiss and calc-silicate rocks and is conformable with both the footwall contact of the complex, and the layering and gneissosity in the enclosing rocks. Minerals of economic interest are eudialyte (sodium-zirconium silicate), mosandrite (sodium-titanium silicate), britholite (calcium-silica phosphate), and a few other uncommon zirconium and titanium silicate minerals.The highest and most continuous yttrium grades occur in the upper part of the syenite gneiss unit in areas containing eudialyte, mosandrite and minor britholite. Yttrium also occurs in britholite in calc-silicate rocks and in mosandrite in syenitic rocks in the lower part of the syenite gneiss unit. Both the yttrium-bearing minerals and yttrium grades are erratic in the lower part of the unit. Zirconium is generally more uniformly distributed than yttrium. A peralkaline granite gneiss phase of the complex intrudes the syenite gneiss and possibly truncates it, and the mineralization, near the southern boundary of the mineralized zone.The mineralized zone is coincident with a radiometric anomaly and discontinuous yttrium and zirconium soil anomalies.More drilling and metallurgical studies will be required to determine the economic viability of the yttrium and zirconium mineralization at Kipawa."

Jan 1, 1992

By Steve Scott

Green Economy Toyota Prius Hybrid contains about 50 kg of copper. All-electric cars have about 100 kg of copper. From where will all the copper come? Wind turbines have 1 metric ton of copper China is building 221 cities of 1 million people by 2025 (13 cities per year from 2008) = 10 New Yorks. The Greater Toronto Area has 5.6 million people, so a new GTA every 22 weeks!

May 1, 2013

By R. J. Allan

"CANADA HAS A GREATER LAKE AREA than any other country. Discountin the Great Lakes, this fresh-water area, mainly in the Canadian Shield, is listed as approximately 300,000 sq. mi. Densities of lakes range up to 7,500 in a 5,294-sq. mi. area of the Shield, southwest of Reindeer Lake, Saskatchewan. Five areas chosen randomly from the Shield (Figure 1) contained sufficient lakes to provide samples at a density of at least one per 10 sq. mi. Regional geochemical surveys in the Appalachian area (Nova Scotia, Boyle et al., 1958; New Brunswick, Boyle et al., 1966) and in the Cordilleran area (Yukon, Gleeson, 1965) of Canada and in many other areas of the world have relied heavily on analyses of stream sediments. These surveys show that sampling of material related to the drainage system reflects the over-all trace element content of the rocks and surficial deposits in the drainage basin. In the Shield, the classic types of dendritic (and other) stream systems found elsewhere in the world are very rare. However, impeded and disorganized stream systems that abound with lakes can provide the exploration geochemist with an ideal composite drainage system sample in the form of lake sediment. This paper attempts to demonstrate the feasibility of, and review the theory and problems involved in, the use of lake sediment as a regional geochemical exploration medium. Most of the references to field examples are taken from a regional survey using lake bottom sediment as the sample medium over 1,500 sq. mi of the Coppermine basalt group and adjacent rocks (Figure 2). During this regional survey, detailed sampling of several lakes was carried out and the results are referred to at appropriate places in the text."

Jan 1, 1971

By X. Xu, J. K. -W. Wong, J. -Y. Delenne, K. Soga

Hydraulic fracturing (HF) is a mulit-scale and multi-physics process which makes numerical modelling challenging. Conventional numerical models focus on multi-physics nature of HF but the multiscale nature is compromised by idealization of reservoir to be continuous, homogeneous and isotropic. However, natural fractures take a significant role in the success of HF for exploration of unconventional resources like Shale gas. Advancement in microseismic monitoring provides useful data for simulation in a much greater details. There is an urgent need to develop a suitable numerical tool for multi-scale threedimensional simulation to better understand the roles of discontinuities and heterogeneity in reservoir and its interaction with HF, especially to address the environmental concerns such as induced seismicity. In this paper, a simple discontinuum numerical method – Lattice Element Method (LEM) is proposed to model HF in a large scale three-dimensional model. A reservoir is modelled as a lattice network composed of 1D Hookean’s spring. Fracturing is modelled simply by removing lattices that meet a specified threshold as determined by the critical energy release rate of the rock. By introducing disorder in the model, mesh dependency in modelling fracture growth is minimized. Fluid flow is simplified as flow in pipe network and the permeability of pipe is related to fracture aperture by cubic flow law. Therefore, fracture flow and rock deformation are fully coupled. In this paper, four simulations of the same configuration except with different degrees of reservoir heterogeneity are presented. Fractures formed are diffusive and two groups of fracture are identified – connected fractures and isolated fracture without clear spatial correlation. The former forms a ‘fracture cloud’ and contributes to fluid flow and modeled by pipe network. The flow of fluid is highly tortuous and pipe network is sparely connected. The degree of reservoir heterogeneity controls the growth of ‘fracture cloud’ and pipe network. Microseismic monitoring often shows diffusive fracturing during HF on site and hence the outcome of the proposed model can be compared to such monitoring results.

Jan 1, 2015

By W. J. Taylor, T. D. Parris

"Over 90,000 feet of raise have been bored at International Nickel underground mining operations throughout the Sudbury District since the advent of raise boring in the early part of July, 1964. With a total of 10 raise borers on hand at this time, techniques have improved steadily since introduction at INCO mines. The first unit, designed for use in rock of low compressive strength, had to be modified and redesigned to cope with Sudbury Area Precambrian rock. As equipment and boring techniques improved, a specially designed machine for larger holes was developed and is now in use. More powerful units, with a thrust capacity of up to 750,000 pounds, are under investigation. Raises have been bored up to 84-inch diameter, and the changeover to 5- and 6-foot flat reaming heads with improved cutter design has increased performance substantially. As a result, 5-foot-diameter raises have been completed to a length of 750 feet and 6- and 7-foot raises to over 500 feet. Reference is also made to the drilling of over 23,000 feet of drainage and sand-fill holes, ranging up to 7% inches in diameter, with smaller underground rotary drill equipment.Finally, a look into the future indicates the need for further improvements in equipment design to permit economic boring of 7- to 8-foot-diameter raises in Sudbury Area ground types."

Jan 1, 1972

By G. L. Zhu, Y. F. Wu, H. Nagaumi

A novel eutectic-type alloy Al12Si-HTC with high thermal conductivity has been developed by strict chemical composition control and heat treatment. The thermal conductivity of the alloy is about 30 % higher than that of current commercial Al12Si alloy. The Al12Si-HTC alloy has a silicon content of 10~12 wt.%, which provides excellent castability. Trace element strontium or calcium is added to modify eutectic silicon, and contents of transition elements such as copper, manganese are controlled in a low level. By appropriate heat treatment, thermal conductivity of the castings increases by 7.5 % and finally reaches 172 W/(m·K). It is found that eutectic silicon modification which makes average particle size finer than 2µm plays a dominant role in improving thermal conductivity, as well as further spheroidization of eutectic silicon and reduction of lattice defects in a-Al microstructure in subsequent heat treatment process. The alloy is successfully applied to produce a certain communication enclosure with complex finned structure by die casting process in industrial scale. The results of numerical simulation and thermal analysis experiments show that when manufactured by Al12Si-HTC alloy, the surface temperature of chips in the enclosure is reduced by 2.0~4.5 ? and the temperature distribution is more homogeneous compared with traditional Al12Si alloy.

Jan 1, 2015

By S. Vongpaisal, T. R. Yu

"A set of new blast damage criteria has been developed, with special reference to blasthole mining operations, for assessing damage by incorporating the vibration level, rock properties, site characteristics and the effects of ground support systems. The main objective of this work was to provide a database with reasonable accuracy for use in optimizing blast design, numerical analysis and ground control expert system module development.The new damage criteria allow one to estimate the degree of damage to rock structures in terms of a dimensionless parameter defined as Blast Damage Index (BDI). This allows for the description of blast damage in a unified form, and facilitates the development of codes for numerical modelling to express the degree of blast damage universally. A number of field investigations from several stope production and slot opening blasts at a large underground base metal mine were carried out to verify the developed index. The results show a good correlation between the observed damage and the type of damage predicted from the BDI values.Practical measures are also provided for minimizing blast damage in large underground blasthole mining operations"

Jan 1, 1996

By L. Vinnett, T. Ledezma, F. Contreras, F. Díaz

"Mass balances in secondary grinding are subject to critical constraints mainly because of the unknown load distribution from the SAG mills, the uncertainties in the hydrocyclone split estimations and the lack of flowmeters in the key streams. In this paper, a methodology to support mass balances based on the use of radioactive tracer is presented. This approach was successfully implemented in two secondary grinding circuits of Minera Los Pelambres, which operate with ball mills of 21’ x 33.5’. The method allowed the load distribution of the SAG product (secondary grinding feed) to be determined. This load distribution was used as an input in the mass balance data reconciliation.The effective residence times of solid tracers were obtained in the secondary grinding equipment, where irradiated solid was used as a tracer. The residence times were obtained from the parametric deconvolution between the input and output tracer signals. The model fitting was performed to reconstruct the normalized output tracer concentration. Effective residence times of solid tracers in the ball mills ranged from 1.9 min to 9.5 min. The use of radioactive tracer measurement in grinding circuits is a powerful tool to consolidate mass balance results as well as to characterize grinding mills.INTRODUCTIONGrinding is the last stage of the comminution circuits. At this stage, the ore particles are reduced in size by a combination of impact and abrasion, either dry or wet (Austin & Concha, 1994). The grinding equipment mostly used in industrial operations correspond to horizontal tumbling mills (Wills & Napier- Munn, 2006). Tumbling mills employ steel balls or rods as grinding media. Ball mills, which are a type of tumbling mills, use steel grinding media with greater surface area per mass unit than SAG (semiautogenous grinding) mills or rod mills (primary grinding). Hence, the ball mills are suitable to obtain the particle size required in the next separation stages (Napier-Munn et al., 1996; Wills & Napier-Munn, 2006)."

Jan 1, 2016

By Roland B. Hoag, Roger G. Webber

Sulphate concentration in groundwater is a good measure of the extent of oxidation of sulphides, provided that sulphide minerals are the primary source of the sulphate. A study was conducted near the Eustis Mine in Quebec to determine where and how the sulphate in groundwaters originated. Atmospheric precipitation is the only source of sulphate other than oxidation of sulphides, and in this study area it is equal to 0.01,. millimole per litre. The oxidation of sulphides can be divided into subsurface oxidation (mainly inorganic processes) and surface oxidation (including both organic and inorganic processes) . The maximum sulphate concentration due to subsurface oxidation of sulphides depends on the solubility of 0 2 in water and is 0.25 millimole per litre. Surface oxidation is, therefore, responsible for any amount greater than atmospheric plus subsurface contributions (0.29 millimole per litre). Surface inorganic oxidation occurs in waters with a pH greater than 15 and is controlled by the kinetics of the oxidation processes. Organic (bacterial) surface oxidation is dominant only in acid (pH< 1.5) waters. The bacterial action accelerates the oxidation of sulphides, and large quanttties of sulphate may be introduced into solution.

Jan 1, 1976

By V. G. c Papangelakis, M. Huang

A conductivity cell, developed previously, was employed in an effort to investigate the inter-relation between electrical conductivity and acidity of sulphuric acid - metal sulphate solutions at high temperatures. The measured solutions include the H2SO4-H2O, MgSO4-H2O, H2SO4-MgSO4-H2O, H2SO4-MgSO4-Al2(SO4)3-H2O solutions. All solutions reported in this paper were measured from 15 to 250 °C at equilibrium vapour pressure. The maximum measured concentrations of H2SO4, MgSO4 and Al2(SO4)3 were 0.45 m, 0.30 m and 0.10 m, respectively. It was found that, from 15 to 250°C, there is a linear relationship between H2SO4 concentration and electrical conductivities for acid concentration up to 0.45 m. At 250 °C and constant H2SO4 concentration, the solution conductivity drops with the increase of MgSO4 concentration. Lt is suggested that this drop is caused by a decrease in the concentration of H. Finally, an empirical model was developed based on the available measurements. This model has been tested against real laterite leach solutions where sulphuric acid and metal sulphates are dominant electrolytes. The average difference between the estimate acid concentration from this model and the one from titration was less than 5%.

Jan 1, 2004

By A. G. Lylie

Introduction At the Britannia Mining and Smelting Company&apos;s mill, the equivalent of 2,500 to 2,800 pounds of copper sulphate crystals per day is made from copper which is precipitated from the mine-water. This copper sulphate is used in the mill for the recovery of sphalerite by2 flotation. From 1932 until 1936 it was produced by exposing the precipitate to air for thirty days and then dissolving the oxidized copper with dilute sulphuric acid. In 1936, the flotation of sphalerite was discontinued and, when it was resumed in 1947, steps were taken to try to improve the former method. The present paper outlines the way in which this was done, and describes the plant and procedure by which copper sulphate is now being made, and by means of which an appreciable saving is being effected. Aboratory Tests The previous work had established that the precipitate, which consists mainly of metallic copper, must be oxidized before the copper would dissolve in dilute sulphuric acid. Various methods for oxidizing it were tried but in the early laboratory work the only suitable one found was to heat the precipitate to 600°C. and hold it at this temperature for two hours. When this was done, approximately 90 per cent of the copper became soluble in .acid. This percentage was considered satisfactory for practical purposes, but the cost of roasting was prohibitive because only a small amount of roasted precipitate was required each day.

Jan 1, 1951

By A. F. Buckham

Introduction Several basins of the Nanaimo series, a group of coal-bearing sedimentary rocks of Upper Cretaceous age, underlie parts of Vancouver island and the adjacent gulf islands. One, the Nanaimo basin, occurs on the southern half of the west shore of the gulf of Georgia. About fifty square miles at the north end of this basin are known to be underlain by productive coal seams, this area being known as the Nanaimo coal field. Coal has been mined from two horizons- that of the Wellington seam, fairly low in the series, and that of the Newcastle and Douglas seams, about the middle of the series. Coal has been mined here since the fall of 1852. About fifty million tons have been produced, almost half the total production of British Columbia. About seventy-two years ago, James Richardson of the Geological Survey made a reconnaissance of the coal measures on Vancouver island, and thirty-five years ago C. H. Clapp mapped and reported on most of the Nanaimo coal field. Twenty-four years ago, J. D. MacKenzie extended the work to those areas not mapped by Clapp. MacKenzie died before the results of his work could be published, but did issue a revised estimate of the Goal Resources of Southern Vancouver Island. Work by the present writer is a further contribution by the Geological Survey to knowledge of the island coal measures. Having spent more time in the field, and having had more data at his disposal than were available to his predecessors, the writer has been able to throw additional light on the Nanaimo, and other, coal fields on Vancouver island. He is indebted to Canadian Collieries (Dunsmuir), Limited, and to its officials for access to much valuable information in their possession.

Jan 1, 1947

By J. B. Mawdsley

A LITILE north of the geographic centre of the Province of Saskatchewan, 150 miles north of the city of Prince Albert, is a narrow green-stone and sedimentary belt of pronounced structural characteristics. This belt, generally known as the Sulphide Lake belt, is about two and a half miles wide. During the past three years prospecting has uncovered numerous gold-bearing showings occurring chiefly along the centre of the belt for a distance of at least nine miles. The number of these showings, the nature of some of them, and their relationship to strong structural features, make it altogether likely that intensive work will eventually locate ore-bodies that will be of economic importance. The discovery of gold in the fall of 1938 on the south shore of Mackay lake, about five miles northwest of the Sulphide Lake gold-bearing belt, indicates that there are neighbouring zones of interest. This paper, an attempt to outline the present status of the interesting mineralized belt, is based largely on the information gained on a five-day tour of this district, made in August, 1939, on behalf of the Department of Natural Resources of the Province of Saskatchewan. The Sulphide Lake belt is named after a small lake centrally located in it. This lake and others are just north and within short portage distances of some of the long bays along the north shore of Lac La-Ronge, an irregular, island-studded lake, about twenty miles in diameter, in relatively rocky Precambrian country, just north of the Palaeozoic contact. The fur-trading post and settlement of Lac La-Ronge is on the west shore of this lake and a road, now under construction, will shortly link this community with the city of Prince Albert. In the past, the most direct route was an indifferent canoe route, in part following Montreal lake and river; more recently, the aeroplane has made this section easily accessible.

Jan 1, 1940

By M. F. Almeida

"Due to the randomness of all factors influencing the sintering operation, a two-stepped procedure is proposed to find the best way of using stocked fines at a plant producing Fe-Mn alloys for the steelmaking industry. The approach is based on the following: (1) predict the result of the sintering operation by establishing the best multilinear regression model using some of the characteristics of the loaded material; and (2) find the best solution under a minimizing cost criteria by solving a linear optimization problem using the regression equation plus constraints on the feed and product. IntroductionSome tests carried out using 20% to 30% of sinter in the material loaded into a 60 000 KVA Tysland-Hole electric furnace producing Fe-Mn alloys for the steelmaking industry indicated: (1) a meaningful decrease in the off-gas temperature and, consequently, a better energy use due to the material higher porosity; (2) more uniform heat distribution as a consequence of the electrode reaction zone enlargement; (3) an improved furnace control resulting in a smoother operation; and (4) a decrease in gas production facilitating the off-gas treatment. For some years, this plant used only the coarse fraction of the Mn ores, thus stocking all the received and own-generated fine particles. In view of the mentioned results, a strategy for increasing the use of stocked fines was formulated, including a step where it was necessary to decide which components and respective quantities should be used in the blends to be sintered (Almeida, 1984).It is well known that several factors affect productivity and energy consumption in sinter production, also influencing the product quality. Raw materials characteristics, namely chemical and size composition, affect permeability to gases and may or may not allow a deeper bed. In general, finer ores decrease permeability, increasing electricity consumption by fans, but due to their higher specific surface area, react more completely with other components in the mixture. For coke granulometry, a compromise must be obtained in order not to burn it too quickly nor to widen the flame front, therefore decreasing productivity. Decreasing coke in the blend also acts in sinter bonding, decreasing its consistency and increasing crushing and return fines. Moisture addition also influences components mixing, pre-agglomeration, bed permeability and, consequently, sintering productivity. Therefore, optimum conditions must be established for both a given sintering plant and the components in the feed (Dawson, 1993)."

Jan 1, 1998

By L. Jones, S. R. Lawrence, A. R. Holloway

Whilst dense medium separation is best known for its ability to concentrate diamond and coal deposits, the process is now being employed in southern Africa as a pre-concentration step to improve the economics of platinum group metal and nickel ores. DMS plants built for these industries (such as the 1600tph unit at Tati Nickel, Botswana), are spearheading an expansion in this area by reducing mine and process operating costs yet maintaining economic metal recoveries. This paper provides an overview of DMS technology and examines the economic benefits available to North American operators and projects, with recent case studies as reference.

Jan 1, 2009

By W. G. Hubler

History The Aldermac mine is situated on the Nipissing Central railway near the &apos; centre of the township of Boischatel, Quebec, and is about ten miles west of Noranda. Aldermac Mines, Limited, is a subsidiary company of Towagamac Exploration Company. The property was staked by Messrs. Alderson and MacKay and McMartin, during the winter of 1922-23. During October, 1925, a copper discovery was made by K. W. Fritzsche, who was in charge of exploration work at that time, the first trench on this discovery averaging 8 per cent copper over a width of ten feet. This led to the discovery of another body 200 feet to the north, with an average of 3 per cent copper over fifteen feet in width. A magnetic survey was then carried out which led to the location of the large pyrite ore-bodies which have been developed in the past few years. Development work was carried on to a depth of 1,125 feet, and approximately three million tons of massive pyrite ore was indicated. Extensive metallurgical tests were conducted in the laboratories of the Mines Branch of the Department of Mines at Ottawa to determine the proper metallurgical treatment and the economic possibilities of the ore. Owing to the comparatively low copper content, and the uncertainty of the copper market, it was doubtful if the mine could be profitably operated for the production of copper alone. Messrs. Alderson & MacKay, however, realized the possibility of utilizing the large tonnage of pyrite as a substitute for native sulphur, &apos;which in past years has been imported into .Canada for the manufacture of acid and sulphate pulp in paper mills. They therefore organized the Sulphite Research Corporation with the object of developing an economical process of utilizing the pyrite.

Jan 1, 1932

By S. Markstrom

The Boliden AITIK copper mine is located 100 kilometres north of the Arctic Circle in northern Sweden. A pre-feasibility study was conducted in 2005 with the aim of increasing the capacity of the existing processing plant. After analysis, options to upgrade the existing plant were abandoned in favour of building a new processing plant, with higher capacity and therefore greater profitability. A new plant could be designed with greater flexibility to make potential future expansions easier. A feasibility study for a new 36 Mt/y processing plant including fully AG grinding circuits and flotation was completed in 2006. The project was approved by the Boliden board shortly thereafter. Construction started in the beginning of 2007 and was completed during 2009. Commissioning of the new plant was undertaken in the first half of 2010. The grinding circuit consists of two lines with each line consisting of a 22.5 MW AG mill and a 10 MW Pebble mill in closed circuit with a spiral classifier. The nominal production level is 2 200 t/h for each grinding line. This paper presents the start-up and operation of the grinding circuit.

Jan 1, 2012

By A. A. de Gast, R. B. James

"The metal content of ore blocks can be calculated by the use of many different methods. These methods range in sophistication from manual calculation to computer. oriented techniques. In this case a cubic polynomial regression model is developed to depict the grade distribution of an orebody. Mine production, in stope dimensions, is then simulated on a computer to predict the output of metal content. The volume, grade and variance of the grade are estimated by triple integration and matrix algebra. A case study shows reasonable agreement between the results from the mathematical model and the mine geologists' estimate of production and ore reserve grade and tonnage."

Jan 1, 1972

By C. Bergstrand

"Precipitation of gypsum and the formation of scale may pose a serious challenge in the leaching of several minerals. As an example, precipitated gypsum may form scale in the machines increasing the need for maintenance. Alternatively, it may encapsulate precious elements, i.e. gold and lower the recovery during subsequent leach processes. In this work we explore how different biopolymers modify the rheology of gypsum at three different pH levels at ambient and elevated temperatures. The ability to disperse gypsum vary with temperature, pH and biopolymer. It is also inversely related to the scaling potential. Measurements of the zeta potential as a function of increasing amounts of biopolymer reveals that the magnitude of the zeta potential changes in the presence of biopolymer, and so does the ability to disperse the gypsum suspension. Similar results with hematite will also be discussed. The methodology and results may aid in the selection of additives used in mineral processing applications where scale pose a problem.INTRODUCTION Processing of refractory gold ores normally involve either atmospheric or oxidation under pressure in order to convert sulfides to oxides (Weir, King, & Robinson, 1986; Weir, Robinson, & King, 1986). This conversion facilitates leaching of gold (and silver) in normal CIL processes. During oxidation, sulfides are converted to sulfates. Normally, there is an abundance of calcium ions in the process water, either released from the ore or added as lime to adjust pH for the CIL process. Precipitation of calcium sulfate, or other compounds (calcium carbonate, jarosite, hematite) is a way to remove gangue minerals from the solution entering the CIL circuit (Ji, King, Fleming, & Ferron, 2010). Precipitation may also cause challenges in the process as gold (or other valuable elements) may become encapsulated in gangue. (Beauchamp, Choung, & Xu, 2006). In addition to precipitation, the precipitated gangue minerals may solidify and form scale in the processing equipment. Recently, Lauten and Kluck (2016) found that dispersants used as scale inhibitors to prevent encapsulation of gypsum did not modify the solubility of gypsum. In the utilised model system, similar amounts of gypsum precipitated with and without dispersants. Instead, it was found that the dispersants evaluated as scale inhibitors reduced the yield stress of gypsum suspensions. The reduced yield stress was associated with a reduced tendency for gypsum particles to agglomerate and form scale."

Jan 1, 2017