Search Documents

By R. Kaibyshev, I. Zuiko

"The effect of thermomechanical processing (TMP) including cold working by tension or rolling before aging on mechanical properties and a dispersion of secondary phase particles of an AA2519 alloy (Al–5.64Cu–0.33Mn–0.23Mg–0.15Zr–0.11Ti–0.09V–0.08Fe–0.01Si (wt. %)) was examined. It was shown that the use of tension to impart pre-strain =10% in the alloy provides the best combination of properties in peak aging condition of the material. The AA2519T87 alloy processed by tension exhibits the yield stress, ultimate tensile strength and elongation to failure of 425.4±2.4, 475±2.4, 12.1±0.4, respectively. The one pass rolling leads to -5% decreases in yield stress and –20% decreases in ductility. Dislocations serve as heterogeneous nucleation sites for ?'-phase precipitation. The positive effect of tension is attributed to the formation of more homogeneous dislocation structure, uniform distribution of ?'-phase particles with higher aspect ratio. Precipitation of the O–phase plates on {111}a habit plane was detected. In addition it was shown that the low angle boundaries are heterogeneous nucleation sites for ?' and O particles.INTRODUCTION Precipitation-hardened alloys are a commercially important group of the materials because their mechanical properties can be modified by treating and changing the microstructure. Age-hardenable aluminum alloys belonging to the Al–Cu–Mg system are widely used due to their attractive combination of high specific strength, good fracture toughness and enhanced creep resistance attributed to the highly efficient strengthening by the ?'-phase (Palmer, StJohn, Nie, & Qian, 2017). An AA2519 alloy exhibiting superior mechanical properties among high-strength Al–Cu alloys (2XXX-serie) due to minor Mg additives. It is known that, in alloys with high Cu/Mg ratio (=5.6) the classic precipitation sequence (Palmer et al., 2017; Wang & Starink, 2005; Wang et al., 2010) of supersaturated solid solution (SSSS) decomposition occurs: SSSS ? GP zones (Al3Cu) ? ?? (Al3Cu) ? ?' (Al2Cu) ? ? (Al2Cu) (1)"

Jan 1, 2018

By M. Bourassa, P. Roy

"This paper describes the automation of Kiena's grinding circuit which comprises an open SAG mill circuit and a closed ball mill circuit with two stages of hydrocyclones. The circuit has been instrumented according to a two level control strategy.The regulatory control strategy is implemented in an industrial controller. This controller does data filtering and calculation (flowrate and solid content) and regulates the pump box levels (2), the water additions: or the pulp percent solids (4) and the fresh ore feed rate.The supervisory control calculates for the industrial controller, the fresh ore feed rate setpoint and the pulp percent solids setpoints in order to optimize the grinding circuit operation. It is made of two modules, one for data filtering and one for control optimization. The filtering program uses modern tools to adjust the measured value and estimate missing data (dynamic material balance, on line estimation of model parameter, etc.). The control program acts as an expert system which combines the benefits of model-based control and rule-based control. A multivariable predictive controller (DMC) is used to maintain the circulating load and the hydrocyclones feed percent solids (which is correlated to particle size) while the rule-based control validates the previous output, detects and avoids the SAG overloads and sump pumps overflows.The system has been operating since MAY 1992 and the benefits obtained are discussed.INTRODUCTIONIn 1990, Les Mines d'Or Kiena decided to go ahead with a project for automating its grinding circuit as proposed by the Centre de recherché minerals (CRM). Its objectives in doing so were to marginally increase production capacity (1 % ) and to create a new challenge for plant staff. The main stages of the project, which involved CRM, Kiena Mines and a consultant, are shown in Table 1. The project was completed in May 1992 with the implementation of a supervisory control system. This text describes the main features of the system with a special focus on its most innovative aspects."

Jan 1, 1993

By D. S. Evans

Major Project Blues Over the last two decades, almost every major project has suffered significant cost overruns, significant schedule delays, and/or poor quality work. Exceptions are rare and most projects that tout being ?On Time and Under Budget? have re-cast schedules, significantly modified scope or revised base estimates. The problem isn?t new. In the late 1980?s the Rand Corporation published a study showing that 80% of all major projects had significant cost and schedule overruns. The problem is not restricted to the Canadian environment, or to a specific industry. It is a global problem.

May 1, 2013

By J. Finch, Wei Zhang

In this paper we describe the synthesis of a new homologous series of linear Polyglycol-based frothers that consist of Ethylene Oxide (EO) and hydroxyl as hydrophilic groups and Propylene Oxide (PO) and alkyl chains as hydrophobic groups. The synthesized frothers were of two types: Alkyl-Ethoxy-Propoxylate (abbrev. CnEOlPOm) and Alkyl-Propoxy-Ethoxylate (CnPOmEOl) giving: (a) different number of groups and chain length, and (b) different locations of the groups. The identities were confirmed by proton nuclear magnetic resonance (NMR) spectroscopy and total organic carbon (TOC) analysis. The characterization of the products was carried out in a bubble column. At steady state, bubble size, gas holdup and water overflow rate were measured as a function of frother concentration. The results indicate that increasing number of PO groups led to significant decrease in bubble size, and increase in gas holdup and water overflow rate. Increasing the alkyl chain length, gave similar but less pronounced trends. There was no impact of increasing the number of EO groups on bubble size but there was an in increase in gas holdup and water overflow rate. Changing the location of the PO and EO group had a significant effect on all three parameters.

Jan 1, 2015

By M. H. MacLeod

"IntroductionTHE ORE PASS raise system at the H.B. mine as contracted by the Patrick Harrison Company consisted of two raises 6 ft. by 10 ft. in section •at 60 degrees to the horizontal. No. 88-88 raise, the longer of the two, was a straight raise 690 feet long, with access only from the bottom. In addition, this raise had two branch knuckle-backs only one of which was driven by. the Patrick Harrison Company. The other, known as 88-89 raise, was 540 feet long with knuckle-backs at 280 feet and 410 feet. Its access, also, was from the bottom (see Figure 1)."

Jan 1, 1954

By Charles S. Ney

"ZINC-LEAD REPLACEMENT deposits straddle the steep-sided valley of Kicking Horse River at a point three miles east of Field, B.c., in Yoho National Park. The Monarch orebodies extend into Mt. Stephen on the south side of the valley, and outcrop at two points, 1,000 and 1,200 feet above the valley floor. The Kicking Horse deposits are in Mt. Field, on the north side of the valley, and they outcrop 200 feet lower.The East Monarch outcrop is said to have been discovered in 1884 during construction of the Canadian Pacific Railway. The larger West Monarch outcrop, 700 feet west of the original discovery, was not reached till 1917 because of its nearly inaccessible location on the cliff face.The Kicking Horse mine was staked in 1906. Little development was done for several decades, and mining was not commenced till 1935.At the East Monarch, mining was commenced soon after location, and several thousand tons of ore were shipped prior to 1912. At this time a gravity concentrator was installed. This was operated till 1924, and a total of 42,000 tons of ore were mined, including about 10,000 tons from the West Monarch. The period from 1928 to 1935 featured flotation milling and the mining of 265,000 tons of ore, mostly from the West Monarch orebody. Intensive exploratory development was carried out in both Monarch and Kicking Horse from 1935 to 1946. Production from both mines in this period totalled 380,000 tons. From 1947 to the time of closure in 1952, considerable new ore was found in both mines and 185,000 tons were milled. Immediate possibilities for finding ore in the Monarch were considered exhausted. Kicking Horse orebodies are known to persist with a low grade of zinc. Total production from the two mines amounts to 842,500 tons grading approximately 7 per cent lead, 10 per cent zinc, and 1.2 ounces per ton silver."

Jan 1, 1949

By P. Leo

Al-Mg-Si alloys are widely used as medium-strength structural materials; extrusion is the most common processing route. In the present hot deformation investigation of a 6060 alloy, the microstructure of the alloy has been analyzed in the as-cast state, after homogenization heat treatment and after hot deformation by tensile tests in the range 400-490°C and 10-4 to 10-2s-1 on both as cast and homogenized alloys. After deformation the microstructure of the as-cast alloy exhibited cavitation. The flow curves at the lowest test temperature T show a gradual softening after a stress peak, being more evident for the alloy deformed in the homogenized state in association with a high yield stress; at higher T a plateau is attained which is lower as T rises and strain rates decrease. For each fixed T, the ductility decreases as strain rate increases for the homogenized alloy whereas, for the as cast alloy, it rises with strain rate. Constitutive analysis gives Q = 240kJ1mol for the homogenized alloy in agreement with published values; this indicates a more rapid strength decline with rising T than Al, suitable for good hot workability along with the lack of cavitation.

Jan 1, 2011

By Y. Kocaefe, D. Bhattacharyay, D. Kocaefe

The carbon anodes used in the electrolytic production of aluminum are made of petroleum coke, recycled anodes and butts, and coal tar pitch. Due to technological advances in the aluminum production technology, aimed at increasing production and decreasing energy consumption and greenhouse gas emissions, better quality anodes are required. Presently, the anode quality is evaluated by visual inspection and the analysis of a small core taken from 1.5-2% of the anodes produced. The visual inspection is susceptible to human error and limited to surface imperfections. The analysis of cores takes time, and therefore, it is difficult to determine the existence of a problem and intervene at the right time. In addition, the core does not represent the whole anode due to the non-homogeneity of anodes. A validated online anode quality control system can highly improve the situation. In this article, an electrical resistivity measurement method developed for this purpose is presented.

Jan 1, 2014

By Daniel E. Walsh, P. D. Rao

"A four-inch compound water cyclone (CWC) was tested to evaluate its gold recovery characteristics when processing -4.8 mm run-or-pit, placer material. Neutron activated placer gold particles (840 to 37 microns) were used as radiotracers (/98Au) in a closed circuit ewe test loop to determine concentrator recovery; a procedure believed unique to this study. The effect on gold recovery of gold size and shape, feed pulp density, feed pressure, vortex finder clearance (VFC), ewe cone type, top-size of the feed solids, presence or absence of heavy minerals in the feed, and the quantity of-37 micron slimes in the feed was investigated in over 300 tests.CWC concentration ratio and the top-size of the underflow solids were both affected by cone type, VFC, and feed pressure. Gold recovery was significantly affected by gold size, gold shape, and concentration ratio. These effects are complex, because significant size-concentration ratio and size-shape interactions exist. Radiotracer techniques showed gold particles had a residence time within the ewe of approximately one second. This study suggests ewe gold recovery is a concentration. This work suggests ewe gold recovery is a function of particle size and shape, and the flow rate through the cyclone. CWC cone ""bed density"" is considered important only as a thin, protective layer, which shields coarser gold particles from the entraining currents and facilitates their movement through the CWC.IntroductionCompound water cyclones (CWC), or automedium cyclones, are enhanced gravity concentrators for the beneficiation for slurries of sand, coal, and ground ore (Fig. 1). They are called compound water cyclones because of the compound slopes of their basal cones (Fig. 2) and are operated to suppress classification phenomena in favour of gravity concentration effects. The compound water cyclone is not a new wet concentrator. It was developed in the late 1950s by Dr. Jan Visman through research sponsored by Canada's Department of Energy, Mines, and Resources. Since that time, it has become a common unit in coal washeries for cleaning fine coal. CWCs and other versions of concentrating cyclones have also shown promise for heavy minerals and precious metals recovery."

Jan 1, 1988

By C. Barnett

"The mill at Noranda Mines Limited, Geco Division in Manitouwadge, Ontario went into production in 1957 treating 3,500 tons per day of copper, zinc, silver, lead ore. It was not until 1964, however, that the zinc concentrate drying plant was constructed. In 1970, milling capacity was increased from 4,000 to 5,000 tons per day. The zinc content of the ore is quite variable so that the tonnage of zinc concentrate dried varies from 200 to 650 tons per day.The drying plant was designed to dry 25 tons of zinc concentrate, dry basis, per hour from an initial moisture of 8.5% to a final moisture of 2%. Major components were selected so that capacity could be increased to 35 tons per hour with minor modifications.The rotary dryer is a Hardinge type ""XH-12"" with a diameter of 80"" and a length of 50 feet. The all welded construction shell is 1/2 inch thick mild steel plate with 3/4"" thick reinforcing bands under the tires arranged for operation at a slope of 1/2 inch to the foot. The 3/8"" x 12"" radial flights are welded to the shell. There are no flights in the last ten feet of the shell in order to reduce dusting. This unit is driven by a 50 HP motor through a Hamilton type CD250 double reduction helical gear speed reducer. The shell speed is 5.8 RPM.The standard Peabody horizontal air heater has a rated capacity of 10,000,000 B.T.U. 's/Hr. The combustion chamber is lined with high temperature refractory brick and is air cooled. The conical outlet section of the air heater is lined with insulating fire-brick. The burner is a type AT wide range mechanical atomizer fired by a type ""CR"" gas-electric ignitor.The Bunker ""C"" fuel is supplied by a Compower duplex pumping, heating and straining unit, including tank hotwell, Powertronic oil line heating system with a 550/24 volt transformer."

Jan 1, 1972

By C. Rodgers, E. (Ted) Warren

"LocationThe Key Lake operation of Cameco Corporation is located at latitude 57°N in northern Saskatchewan, within the southem boundary of the Athabasca formation. The nearest city is LaRonge, located 240 km to the south. Access to the mine is by all-weather road and by private airstrip.Description of OperationThe mill was designed to produce twelve million pounds of uranium oxide (U3O8) a year from a feed grade of 2.4% U3O8. Current production is fourteen million pounds from 2.0% feed.Following grinding, the uranium is leached using sulphuric acid and oxygen in autoclaves. An eight thickener counter current decantation (CCD) circuit is used to separate the uranium-bearing solution from the solid waste residue. The uranium in solution is further purified in a solvent extraction circuit. The purified uranium is then precipitated using ammonia, calcined at 840°C, and packaged in drums for shipping to refineries. There is a crystallization circuit to recover excess ammonium sulphate produced in the process, and a waste treatment circuit.HistoryUranerz Exploration and Mining discovered the Gaertner and Deilmann orebodies in 1975 and 1976, respectively. Between 1975 and 1977, Uranerz conducted laboratory studies and delineated a process for the Key Lake ore known as the ""Bonn process."" In 1977, Sherritt Gordon Mines Ltd. was retained to conduct further studies in cooperation with U ranerz. The technical feasibility of the Bonn process was generally confirmed. Howeve1~ alternative processing methods also appeared feasible, and over the period 1978-1979, a detailed research and development program was conducted to finalize the processes to be used and to provide data for design of the plant."

Jan 1, 2000

By Limao Zhang

This paper presents a BIM-based Risk Identification Expert System (B-RIES) for metro construction, composed of three main built-in subsystems: BIM extraction, knowledge base management, and risk identification subsystems. The engineering parameter information related to risk factors is extracted from the BIM of a specific project where the IFC standard plays a bridge role between the BIM data and metro construction safety risks. An integrated knowledge base, consisting of fact base, rule base and case base, is established to systematize the fragmented explicit and tacit knowledge. A hybrid inference approach, with case-based reasoning and rule-based reasoning included, is developed to improve the flexibility and comprehensiveness of the system reasoning capacity. During the safety risk identification process, B-RIES is able to improve the inefficiencies in engineering information extraction, reduce the dependence on domain experts, and facilitate knowledge sharing and communication among dispersed clients and domain experts. A typical safety hazard identification in the Mingdu station, located in the Wuhan Metro Line Two, is presented in a case study. The results demonstrate the feasibility of B-RIES, and its application potential. B-RIES can be used as a decision support tool to provide guidelines for safety management in metro construction, and thus increase the likelihood of a successful project in a complex environment.

Aug 1, 2013

By T. W. Cavers

The Dwight-Lloyd sintering machine was the answer to the flue-dust problem of the copper blast-furnace smelter. Then came concentration by flotation, which threatened to eliminate the blast furnace from the smelting field altogether, and again the sintering process solved the problem. As is well known, the sintering process is dual in its function; it expels sulphur from the charge and it converts a powdery material into nodules or chunks that hold together. The charge is ignited on top just as it passes over the edge of the first suction box, and the oxygen of the air that is drawn downward through the charge breaks up the sulphide and oxidizes about fifty percent of the sulphur. The heat produced by this reaction in the upper stratum of the charge ignites that lying immediately below, and, when the pallett has travelled the full length of the machine, the tire has reached the graces and the fine concentrate has changed its characteristics by being partially fused and has become a more or less solid mass. When the Granby Company was smelting its ore as mined, one small D-L machine was adequate for the treatment of the flue dust, but as soon as the policy of smelting the concentrate was adopted, it became necessary to add two large machines to the sintering plant. The three sintering units, of which two are 42 in. by 396 in. and the other 42 in . by 264 in. in hearth area, have a combined capacity of from 370 to 450 tons (dry) of charge per day. The capacity varies directly as the hearth area. The sinter produced is about 88 per cent of the dry charge, or 325 to 400 tons per day. The sintered fines returned for resintering average between 30 and 35 per cent of the charge, but this is not as great a disadvantage as might appear, since the addition of hot fines improves the burning qualities of the mixture. From 50 to 54 per cent of the sulphur is eliminated in the sintering operation.

Jan 1, 1934

By Hans Lundberg

During the last few years, geophysical methods have been introduced to aid mining geologists and mining engineers in locating mineral deposits. These methods have been developed as the result of investigations of various physical characters of minerals and rocks. In prospecting for ore-bodies, electrical methods have proved most successful. These methods are based on the great differences in electrical properties, and especially in conductivity, between ore minerals and rock minerals. The electrical resistance of the common minerals, rocks, and ores in ohms per cubic céntimeter is given in the following table: [ ] The first attempts at electrical prospecting were based on observing currents of polarization around certain ore bodies, which currents it was possible to measure. This method has been developed by Prof. Schlumberger and has been utilized by him successfully. He is represented on this continent by Mr. Sherwin Kelly, who has successfully operated the method here.

Jan 1, 1926

By M. J. S. Innes

Abstract This paper is an account of an investigation made by the Dominion Observatory with a gravity meter and magnetometer over sulphide concentrations at East Sullivan, Val d'Or, Que., in June, 1947. The topographic relief over the area does not exceed 20 feet. The overburden varies from 0 co 50 feet. The west orebody had been outlined by extensive drilling. The average density contrast between the sulphide body and surrounding rocks is 0.5. Two hundred and sixty gravity and one hundred and ninety magnetic stations were observed. The results are shown on contour sketches. A derailed account is given of the methods employed to reduce the gravity observations. The survey shows that both gravimetric and magnetic methods are useful in delineating sulphide deposits under the conditions in which they occur at East Sullivan. The results indicate that the buried contact of the syenite intrusive southeast of the orebody could be traced with the gravimeter and chat the magnetometer was of little value for that purpose. Gravity anomalies due to the varying depths of overburden are negligible as compared to the magnitude of the total anomalies. Introduction The project was first suggested at a meeting of the Associate Committee on Geophysics of the National Research Council in September, 1946. At that time it was pointed out that the accuracy and speed of operation of the new gravity meters made them of special importance for geophysical prospecting and it was highly desirable to have an objective test of the performance of an instrument of this kind in delineating an orebody of known dimensions and density characteristics. Several years ago, a private company did some work with a gravimeter over the Amulet deposits, near Noranda. Unfortunately, the topography there is rather rugged, with hills and ravines exceeding 100 feet, so that the topographical effects rendered it impracticable to distinguish between anomalies due to the sulphides and those due to surface irregularities. An orebody of a typical nature, where the disturbing topographical corrections were not excessive, was therefore sought.

Jan 1, 1949

By Mansoor Barati, Xue Yin, Yanhui Sun, Alex McLean, Yindong Yang

The formation and evolution of inclusions in Ti-Stabilized, 17Cr Austenitic Stainless Steel produced by the ingot casting process were investigated through systematic sampling of liquid steel and rolled products. Analysis methods included total oxygen and nitrogen contents, optical microscopy, scanning electron microscopy (SEM), and energy dispersive X-ray spectroscopy (EDS). The results indicate that the composition of inclusions was strongly dependent on the types of added alloying agents. During the AOD refining process, after the addition of ferrosilicon alloy and electrolytic manganese, followed by aluminum, the composition of inclusions changed from manganese silicate-rich inclusions to Al2O3-rich inclusions. After tapping and titanium wire feeding, pure TiN particles and complex inclusions with Al2O3-MgO-TiOx cores coated with TiN were found to be the dominant inclusions when [%Ti] was 0.307 in the molten steel. These findings were confirmed by thermodynamic calculations which indicated that TiN inclusions could be formed in the liquid phase due to the high contents of [Ti] and [N] in the molten steel. From the start of casting to the rolled bar, there was no obvious change in the composition of inclusions compared to the titanium addition stage. Stringer-shaped TiN inclusions elongated along the rolling direction with lengths varying from 17 to 84µm were observed in the rolled bar, which could detrimentally impact the mechanical properties of the stainless steels.

Jan 1, 2015

By Long Han, A. V. Kalinin, Xiujian Luo, Xiaobo Wang, Xiaoou Xia

"Inertia vibration crusher is a kind of vibration equipment which crushes ore by vibration. When the inertia vibration crusher works, ore between the two moving jaws is subjected to the high frequency contact force, which is produced by the two moving jaws with high frequency synchronous reciprocating motion. The synchronous motion of the two moving jaws depends on the self-synchronous feature of the inertia vibration crusher. To study the self-synchronous feature of the equipment, the dynamic model was established, in which relative parameters were taken into consideration. The kinematic coupling relations of the assemblies are discussed, and appropriate calculation method is chosen to solve the vibrating differential equation. Whether the two vibration exciter can realize synchronous operation depends on the ability of the vibration system's capture moment. Results show that though the two rotors’ motors and damping coefficients are different, and two jaws’ damping and stiffness coefficients are also different, as angular velocities of the two unbalanced rotors reach a certain value, the vibrating system can be stable. Their angular velocities tend to be equal, and the swings of the two moving jaws can be the same. The horizontal vibration and swing of the frame are large in a few seconds after starting the machine. When the system runs stably, the horizontal vibration and swing vanish, and the vertical vibration is stable. The study and its results can provide reference for the optimization design and parameter setting of inertia vibration crusher and related vibratory equipments.INTRODUCTIONMaterials can be easily broken by using the inertia force of the vibration exciter, which can effectively realize the selective crushing, reducing excessive combinations and the energy consumption, as introduced by Zhang in 2005. The initial micro crack between crystals in the material increases and new cracks can be manufactured because of the high frequency impact and the extrusion of the vibration crusher, so vibration crushing equipment can make it possible for any high strength brittle material to be broken theoretically. Inertia cone crusher and inertia vibration crusher have been successfully used in the treatment of metallurgical slag and construction waste, and it verifies the efficiency of vibration crushing."

Jan 1, 2016

By J. Walenzyk

This report investigates the limited use of super large backhoes in surface mines around the world. The demand for super large (> 700 t) hydraulic excavators is rising and most of the machines are sold as front shovel (FS) application. Despite advantages in faster cycle times super large backhoe (BH) machines are a minority (ca. 1% of the total machine population). This investigation is based upon the comparison between the volumes available to the BH and FS in one block and before the machine needs to move. The working conditions are created with standard parameters as given by Original Equipment Manufacturers of hydraulic excavators regarding bench height, angle, and material density. The travel amount of both machine types is derived from these volumes and compared. Furthermore, the travel amount of super large BHs is compared to the travel amount of smaller mining BHs and evaluated based on attachment length and bucket size. The calculations conclude that the volume of material recoverable in a single spot is about 75% higher for FSs. This leads to an increased travel for BHs. The combination of both the increased appearance of electrical driven machines (in the class of > 700 t excavators) and the travel amount lead to a high risk of damaging the cable or the excavator. Enlarged wear on the travelling parts is also attended by the higher travelling. A direct comparison of commonly found working set ups shows that the ratio between volumes is 32% which leads to an increased travel amount. In comparison with a 250 t BH, the calculation shows that the smaller BH is able to reach nearly 50% of the volume of the super large BHs. The main reason for this is the respectively high reach on smaller machines which, combined with other factors, leads to a significantly higher number of BHs in lighter classes.

Aug 1, 2013

By Hajime Miki, Gde Pandhe Wisnu Suyantara, Tsuyoshi Hirajima, A. M. Elmahdy, Keiko Sasaki

"Seawater has been reported to depress molybdenite in a copper-molybdenum (Cu-Mo) flotation process at high pH due to the precipitation of Mg(OH)2. Meanwhile, to improve mineral recoveries, collectors are usually added into the flotation cells, thus adding the complexity to the mechanism of bubble-particle interactions involved in Cu-Mo flotation. Therefore, understanding the interaction mechanism in seawater flotation and in the presence of collectors is important to explain the minerals depression. The present work investigated the effect of kerosene on the bubble collision and attachment to pure chalcopyrite and molybdenite surfaces in MgCl2 solution as one of the seawater major components at pH 6 and 11. Mineral surfaces were characterized using atomic force microscopy (AFM). In addition, minerals floatability in the same system were tested in a column flotation. The study of bubble-particle interactions shows that following several collisions, bubble could displace the intervening liquid layer on the mineral surfaces, forming a three-phase contact (TPC). A TPC formed more rapidly in the presence of emulsified kerosene in a 0.01 M MgCl2 solution at pH 6 for both minerals. The reason is kerosene increased the surfaces hydrophobicity and destabilized the intervening liquid layer on the surfaces. Moreover, the average time required to form a TPC was shorter on molybdenite surface. This can be attributed to the effect of adsorbed kerosene on molybdenite surface and molybdenite surface roughness.INTRODUCTIONIn froth flotation, bubbles are used to separate hydrophobic mineral particles from hydrophilic particles. In this process, bubble-particle interactions (i.e., collisions, attachment, and detachment) are crucial with regard to mineral recoveries. The effectiveness of froth flotation depends on the formation of stable aggregates between the hydrophobic particles and the bubbles, allowing the bubble to carry the particles to the froth layer. To form such aggregates, the bubbles and particles must collide, and the intervening liquid layer must be drained below the liquid layer critical thickness, forming a stable threephase contact (TPC) (Ralston & Dukhin, 1999). Particles detachment may take place if the particles still have sufficient kinetic energy and the TPC is not formed. Previous studies of bubble-particle interaction in electrolyte solutions have been conducted using atomic force microscopy (AFM) (Assemi, Nguyen, & Miller, 2008), and by approaching the bubble using mica plate (Pushkarova & Horn, 2008), however, these studies did not focus on the bubble-particle collisions. Bubble collisions and attachment to hydrophobic (Teflon) and hydrophilic (glass) surfaces in a a-terpineol solution have been investigated by Krasowka et al. (2003)."

Jan 1, 2016

By C. H. Stockwell

THE Eastern Townships of Quebec have been the chief Canadian source of chromite. Production, however, has never been large and, except for a period of steady but small output between 1894 and 1909, mining has been active only in war time. The known deposits are too small or too low grade to compete with overseas sources in normal times. During the last war, shipping difficulties and a greatly increased demand in the United States resulted in high prices and a ready market for low-.grade material. The Quebec chromite industry flourished and played an important part in relieving the wartime shortage. Shipments in 1918 .amounted to 15,600 tons of crude ore and 6,400 tons of concentrates. At the outbreak of the present war it was natural to turn again to the Quebec field as a possible source of this strategic mineral. Some of the old properties have since been opened by private and government money and some new deposits have been found. Total mill capacity is 750 tons per day, as compared with 200 to 300 tons in 1918. During 1940, 1941, and 1942, about 85 chromite deposits were examined by the Geological Survey in a belt 100 miles long and up to 7 miles wide. A part of this belt, about 35 miles long, in which the geological features ?were not well known, was mapped on a scale of 1/2; mile to an inch.? Small ..areas around some of the deposits were mapped in detail, on scales of 20 to 200 feet to an inch. Some geophysical work was done but did not result in the discovery of ore. Prospecting by stripping and trenching was then undertaken and chromite ore was uncovered at several localities. The above work was done by the writer and by J. W. Ambrose, who has kindly contributed his results for incorporation in this paper. Y. O. Fortier actd as assistant in the geological work and, in 1942, was in charge of a sub-party engaged in geological mapping. The author is indebted to H. C. Cooke and J. W. Ambrose for reading the original manuscript and for offering many helpful suggestions for its improvement.

Jan 1, 1944