Search Documents

By Dave Stefanuto

Voisey?s Bay Project Components ? Mine/Mill Port In Labrador ? Mini Plant in Mississauga ? Demonstration Plant in Argentia ? Supply Vessel (Umiak1) ? Transshipment Facility (Quebec) ? Concentrate Handling & Transport to Sudbury/Thompson ? Cobalt Refinery Upgrade (Thompson) Project Setting ? The Project is on the traditional lands of the Labrador Inuit and the Labrador Innu ? Canadian courts have held that Aboriginal peoples in Canada possess special rights to traditional Aboriginal lands Those rights can include requiring resource developers to enter into Impacts and Benefits Agreements (IBAs) on traditional lands to set forth how lands can be used and benefits to be received by Aboriginal people

May 1, 2006

By R. J. Visintainer, W. L. Whitlock

"Difficulties with the sizing and operation of centrifugal froth pumps are common and the underlying fluid dynamics are complex. Design and selection often relies on previous experience, offering unreliable guidance for novel applications or unexpected problems. The current paper describes a program of extensive laboratory testing on froth handling centrifugal pumps, covering a range of flows, heads, speeds, viscosity, air content and froth stability. Variations in impeller vane design and the effectiveness of an airlock venting apparatus were also examined. The program resulted in a better understanding of centrifugal froth pump dynamics and insight for the troubleshooting of field applications.INTRODUCTION The Challenge of Pumping Froth In pumping mineral processing froth, the handling of large quantities of air within the fluid is often unavoidable. Efforts to reduce the amount of air present at the pump suction, while always recommended for improving pump performance, may have limitations. Some strategies may also carry an economic penalty, such as unwanted process dilution (e.g. due to water spray or injection), or increased capital cost of equipment due to oversized pumps, sumps and/or piping. Froth pumping losses fall into several categories, as described below and represented graphically in Figure 1. • Density effects: Entrained air reduces the pressure created by the centrifugal pump in direct proportion to the reduction in bulk density. This is not a true “loss”, since the head produced by the pump (in meters of froth), may remain unaffected. However, the reduction in pressure often leads to a corresponding increase in pump speed required to drive the system, which itself leads to increased NPSH required by the pump (NPSHR). Furthermore, by adding a gas phase, the overall volumetric flowrate is increased, assuming a fixed quantity of de-aerated liquid being handled. This leads to increased suction velocity which further reduces the NPSH margin by simultaneously increasing pump NPSHR and decreasing system NPSH available at the pump suction (NPSHA). • Viscosity effects: Increased viscosity introduces an additional factor in some froth pumping applications, such as oil sands bitumen froth. Losses result from increased shear stress within the fluid flow, which increase with flowrate. Viscosity also facilitates the formation of airlock by reducing turbulence and allowing individual bubbles to coalesce more easily within the flow stream. Finally, it increases pump NPSHR by increasing local pressure drop in the vicinity of the vane inlet edges. • Airlock effects: Also known as air binding, it occurs when air or gas coalesces within the pump suction or impeller passages and begins to collect there, held by buoyancy forces within the rotating flow field. In essence, the liquid “floats upwards” towards the pump suction against the outward directed centrifugal forces. The airlock acts as a blockage, with corresponding reductions in flow, head and efficiency. NPSHR also increases, due to increased velocity and distorted streamlines in the flow circumventing the blockage."

Jan 1, 2012

By S. V. Burr

"A 28-year study of cross folds leads to the conclusion that the northwest-southeast folds recognized in many areas of North America are part of a regional pattern. Detailed examination of over 650 geological maps and reports of Ontario indicates that this folding can be traced across the province. Evidence is presented that this fold pattern played an important part in determining the pattern and scale of intrusion, that its recognition in the field can aid in defining stratigraphy, folding and faulting, and that it may have played an important role in channeling hydrothermal or magmatic mineralization. IntroductionThe concept of regional cross folding in Ontario is not new. W.H. Gross (1955) discussed regional cross folds in the Archean of Northwestern Ontario, and A.M. Goodwin (1961) referred to regional cross folds in the Archean of Ontario and Quebec. However, the interpretation in this paper is new.The writer saw a cross fold for the first time, underground, at Little Long Lac Gold Mines in Geraldton, Ontario, in 1951. This recalled the ""transverse folds"" on E.R. Faribault's classical maps of Nova Scotia, published by the Geological Survey around the turn of the century; M.E. Hurst's cross fold(s) at Timmins, Ontario (Figure I); and the cross folds mapped by A.W. Jolliffe in the Yellowknife area of the Northwest Territories. All these mapped cross folds had one thing in common with the fold at Little Long Lac: A northwest-southeast axial trend. Were such cross folds of purely local extent, or might they be indicative of a widespread regional fold pattern? If so, has such folding any significance for mineral exploration or potential?By 1959, based on a study of about 1000 Canadian geological maps and reports, including 291 in Ontario, the writer reached the conclusion that cross folding trending northwest-southeast is so widespread as to constitute a pattern of folding, and that such cross folding should produce changes in plunge along pre-existing greenstone fold belts."

Jan 1, 1980

By Ken Dyck Sr.

"Construction of the Cigar Lake uranium mine in northern Saskatchewan is well under way. Production is anticipated to begin in the first half of 2007. When in full production, the mine is projected to produce a net 18,000,000 pounds of U3O8 per annum from a high grade ore averaging approximately 20% U3O8.Water management was a major issue that required substantial effort in the Cigar Lake design. Not only is effluent quality controlled, a tight water balance to minimize effluent volume is also designed into processes in order to minimize environmental impact. This paper focuses on the water treatment process and water handling equipment, as well as the operating philosophies that will reduce fresh water consumption to a minimum. An overview of the mining and ore handling systems, as well as aspects of controlling water production from the ore formation and the mine development areas will also be discussed.INTRODUCTIONThe Cigar Lake ore body has proven and probable reserves that total 232 million pounds U3O8. Cigar Lake is the world’s largest undeveloped high-grade deposit. It is the second largest highgrade deposit surpassed only by the McArthur River deposit another Cameco - operated mine in the Saskatchewan Athabasca Basin. Cigar Lake is owned 50% by Cameco Corporation, 37% by AREVA (COGEMA Resources Inc.), 8% by Idemitsu Uranium Exploration Canada Ltd. and 5% by TEPCO Resources Inc. When production starts in 2007, ground ore slurry from Cigar Lake will be shipped to the McClean Lake mill (owned by AREVA) some 80 km away. All of the Cigar Lake uranium will be leached from the ore at McClean Lake. During initial production ramp up, all uranium will be processed at McClean Lake to yellow cake (uranium oxide). After the average production has exceeded a 10 million pound per year rate, Cigar Lake uranium will begin to flow from the McClean Lake Mill to the Rabbit Lake Mill. At this point, subject to regulatory approval, 57% of the Cigar Lake uranium, in a uranium rich solution, will be transported to Rabbit Lake mill (owned by Cameco) for purification to yellow cake. A complete summary of the flow of uranium from the Cigar Lake ore body through to product at both McClean Lake and Rabbit Lake can be found in a recent paper titled “The Cigar Lake Project – Mining, Ore Handling and Milling” in the March 2004 issue of the CIM Bulletin. The paper was written by C.R. Edwards."

Jan 1, 2006

By Pierre Lacoste-Bouchet, Ian Orford, Mike Cooper

"The Brunswick Mine ore requires fine grinding to achieve liberation of minerals. With 25mm slugs as the grinding media in the ball mill, there was a limitation of a P80 of 25 microns on the CuPb regrind circuit. Results from pilot plant testing showed that the separation efficiency could be increased through fine grinding with a P80 of 15 microns.Options considered were the capital expenditure for new fine grinding equipment such as a vertimill or the use of the present ball mill equipment with smaller media. The Wheelabrator Allevard Enterprise (WAE) millpebs product was chosen because it was a smaller media with a distribution of steel pellets between 5 to 12 mm.With millpebs the grinding product was reduced in size from a P80 of 25 microns to a P80 of less than 19 microns. The power draw to achieve the finer grind was 13% lower while the media consumption was 57% higher.The millpebs grinding media was also tested on the zinc regrind mill. The purpose of the trial was to understand what the media consumption and power draw would be with the charge lowered to achieve an equivalent grind as obtained with the slugs. The media consumption was approximately the same and the power draw was reduced by 30%.INTRODUCTIONThe Brunswick Mine ore is a complex Pb-Zn-Cu-Ag sulphide ore with the grain size of the minerals varying from submicron blebs to particles up to several mm in size. The ore is ground progressively finer in stages. The first step of grinding occurs in the SAG mill circuit. The product sizing 80% passing 95 microns is fed to the CuPb prefloat stage (Cormier et al 2002). The tails from the prefloat is then further ground to a P80 of 35 microns for the CuPb rougher flotation. The final liberation for the CuPb circuit takes place in the CuPb regrind circuit. The regrinding mill further liberates the cleaner scavenger concentrate, second cleaner tails and third cleaner tails. The reasoning for the progressive grinding is to achieve fine grinding without having galena over ground due to its high specific gravity that preferentially sends it to the cyclone underflow."

Jan 1, 2006

By Jeffrey L. Pagnutti

Train derailment can lead to loss of capital, damage to the environment, and loss of life. Machinery condition monitoring techniques can be used to develop a structural health monitoring system for railway track to detect faults at the incipient stage, before catastrophic failure occurs. This study uses vibration measurements from a novel material haulage unit to develop a decision support system for railway track maintenance. A variety of feature sets and classifiers were compared to determine the optimal configuration for fault detection. The results highlight the shortcomings and advantages of certain methods and describe the process in which the optimal result was obtained. The Parzen data descriptor paired with a refined statistical feature set performed the task of fault detection with less than five percent false positive and false negative classification error. Overall, the outcome of these experiments indicated that condition monitoring of railway systems is a promising approach for fault detection and has the potential to avoid catastrophic failure.

May 1, 2013

By Julie Dénommé

Today few in business would argue with the idea that we are living in a world that is Volatile, Uncertain, Complex, and Ambiguous. Coined VUCA by the US Army War College, these four words define the ?turbulence? and ?continuous white water? that the business literature has been documenting for the last decade. This VUCA world became even more relevant to business in 2007 when the Institute for the Future fellow Bob Johansen published the idea of transforming VUCA into Vision, Understanding, Clarity, and Agility. We call this VUCA Prime (VUCA'), and place an infinity loop (8) between them to show their dynamic interaction. This paper presents an exploration of the impact of VUCA 8 VUCA' on business and the conditions under which these dynamic forces help to successfully navigate change.

Oct 1, 2010

By Walter Durst

On October 16, 1978, the Harnback open cut of Rheinische Braunkohlenwerke, the largest open cut ever planned, was officially put into operation. It will outperform all of the large open cuts known at present, both in its dimensions and in its annual output of overburden and coal. Present plans are to commence coal mining in 1983, although target production will only be achieved in 1995when the annual output will be 50 million tons of coal. Considering an overburden: coal ratio of 6: 1, this will involve the removal of approximately 300 million bank cubic metres of overburden. For overburden removal and coal mining, this open cut will use bucket-wheel excavators exclusively. It is planned to employ eight excavators with a daily output of 240,000 bank cubic metres each (Fig. 1). The transport of the overburden and coal to the dump and the power station, respectively, will be effected by 30Q0-mm-wide conveyors, running at a speed of 6 m/sec. The overburden will be dumped by spreaders having a boom length of 100 m, capable of dumping 240,000 bank cubic metres per day (Fig. 2). Such giants, of course, can only be used for extreme conditions . Their employment indicates that huge quantities of material can be handled economically for long periods. However, the use of bucket-wheel excavators is economic when daily outputs of 5,000 bank cubic metres are involved, in particular if direct backcasting of the overburden is not possible.

Jan 1, 1979

By L. Vollert

In August 2018, the first full-scale HydroFloatTM cells for the recovery of coarse composited copper and gold were commissioned at Newcrest’s Cadia Valley operation in New South Wales, Australia. The primary objective of the installation is to recover coarse value-bearing composites that are lost to conventional flotation tailings, without the need for additional power input for particle size reduction to improve mineral liberation. This paper examines the application of Eriez HydroFloatTM technology for the recovery of coarse, poorly liberated copper sulphide particles drawing on recent experience from lab scale testwork through circuit design and commissioning of the full-scale installation at Cadia Valley. INTRODUCTION In the face of declining copper head grades and a tightening regulatory environment around the use of wet tailings dams, the processing of copper ores at coarser particle sizes has become a focal point for the industry. Sulphide flotation using the Eriez HydroFloatTM is one of the emergent technologies that sits under this umbrella of coarse pre-concentration. It has been demonstrated through numerous lab and pilot scale testwork programs carried out by Newcrest and others (Awatey, Kohmuench, Thanasekaran, Skinner & Zanin, 2013), to improve the flotation recovery of sulphide-rock composite particles with low surface liberation, relative to conventional flotation technology. The HydroFloatTM technology has been used widely for the recovery of coarse potash, phosphate, coal, vermiculite, spodumene and diamonds but has never been applied at full scale in either gold or sulphide flotation. In August 2018, the first full-scale 3.4 m diameter HydroFloatTM cells for the recovery of coarse composite copper and gold were commissioned at Newcrest’s Cadia Valley operation in New South Wales. The primary objective of the installation is to recover coarse value-bearing composite particles that are lost to conventional flotation tailings, without the need for additional upfront power input for particle size reduction to improve mineral liberation.

Jan 1, 2019

By Dale Lens, W. S. (Wayne) Cusitar

"The use of continuous loading and conveying technology for mining is currently practiced in relatively few mining environments and, even in these cases, on a non-exclusive basis. For the most part, and particularly in hard rock mining, appropriate equipment technology has only recently been developed for continuous loaders, mobile low profile crushers and flexible face conveyors. Mining R&D work by Inco Limited has promoted the development and proving of a loader suited to hard rock conditions and capable of sustained loading rates of500 tonnes per hour. Current R&D work at Inco will test the production capabilities of a low profile mobile crusher by CMS/Eagle and a flexible/ mobile face conveyor system by DME. This follows successful production testing of the Belt Bender concepts in potash mining in Saskatchewan and the development of enhanced extensible conveyor equipment features by DME. Numerous applications are seen for variations of the LCC technology in soft rock, hard rock and surface mining environments. Introduction In some respects, this paper is an announcement of new technology which has the potential to bring revolutionary change to the mining industry. It is also the story of technology transfer, in which mining concepts that have developed independently in underground soft rock and hard rock mines and in surface mining operations are being brought together for a common benefit. It is also the story of key developments in equipment technology which 'complete the cycle' of cooperating technical capabilities to enable the revolution to begin. The phrase ""technological revolution"" requires some defmition: an equipment innovation, or invention, or improvement, will only be revolutionary if its use gives rise to a significant new mining practice."

Jan 1, 1987

By T. P. R. de Jong, H. Harbeck

"This contribution reports recent mineral sorting experience and lists the opportunities of the newest generation of automatic sorters with a special focus on electromagnetic detection and Xray transmission. With the available sensor resolutions and actuator systems that are available today sorting of minerals down to 2 mm size and up to 250 mm lump size is technically feasible. In industry, ore as well as coal is still hand-picked and current automation potential only utilised in a handful of specific applications. Recently a number of technological developments took place that may increase sorting potential, save mill costs and lead to lower overall tonnage costs.They are:??High speed and high resolution sorting systems based on X-ray transmission imaging??High speed on-line image processing and further development of advanced data processing??Modular multi-sensor automatic sorting units (using one or more sensors such as colour, electromagnetic and X-ray in a single device)??Sensitive electromagnetic sensors for sorting based on differences in magnetic susceptibility and electric conductivityThe above enables compact dry separation, insensitive for moisture fluctuations and at high separation sharpness, as well as “electronic” high gradient magnetic separation for larger particles. Besides conventional X-ray transmission (XRT), dual-energy XRT (DE-XRT) is now being redesigned to meet the requirements of the mining industry. The mentioned technologies provide automatic dry separation of minerals and rock as alternative for conventional processing."

Jan 1, 2005

By Jochen Franke, Derek D. Lichti

"This paper gives a brief introduction and presents recent enhancements in the MillMapper technology developed for thickness gauging and condition monitoring of liners in grinding mills used for mineral comminution. It also introduces the recent expansion of MillMapper functionality aimed at mill operational optimization. MillMapper uses calibrated laser scanner data captured inside a mill to determine thickness at several million points on all liner surfaces at feed, shell, and discharge ends with millimeter accuracy. Data capture takes nominally 5 minutes, hence interruption to mill operation is negligible.The paper is structured as follows. First, a review of the technology and discussion of recentlyimplemented innovations such as liner change out forecasting, automatic ball charge volume and weight measurement, and automatic mill liner volume/weight measurement for mill operational control or load cell calibration are presented. Combined weight information provides control over load related issues such as load fill levels for relining, or start-up load after reline. Feature descriptions are followed by a listing of the numerous advantages over existing techniques and the benefits to operations. Results from the application of MillMapper are presented throughout.INTRODUCTIONThe need for thickness gauging of liners of grinding mills used for mineral comminution is well known but the task is rarely completed to a satisfactory standard. Liner failure resulting from excessive wear can have expensive consequences. Furthermore, mill performance as well as liner wear are known to be correlated to lifter bar geometry (Napier-Munn et al., 1999; Rajamanni et al., 2005). At present, the following techniques are routinely used to gauge the thickness of mill liners:1. Visual inspection;2. Ultrasonic thickness gauging (for steel liners); and3. Physical inspection (e.g. nail inserted in rubber liners)"

Jan 1, 2008

By E. T. C. Spooner, Ioannou S. E.

"Abstract- The Dixie Zone Au-Ag deposit is a low sulfidation (adularia-sericite) epithermal system located 1.4 km from the producing Ken Snyder mine (7.0 M oz Au equivalent reserve/resource), Midas Mining District, north-central Nevada. This WNW striking, steep south dipping, fault system is hosted by mid-Miocene (17 Ma to 14 Ma) felsic volcanic rocks that were erupted from a vent(s) to the northeast. The system was mineralized by approximately 250 ± 20°C (n = 86), near-neutral pH, ascending fluids of predominantly meteoric origin [volatile corrected salinity = 0.52 ± 0.35 eq.wt% NaCl (n = 86)]. Bulk analytical fluid inclusion gas chromatography identified a mineralizing fluid volatile composition of 99.68 ± 0.18 mole % H2O, 0.16 ± 0.09 mole % CO2, 0.11 ± 0.05 mole percent N2, 0.05 ± 0.04 mole % CH4, and 0.01 ± 0.01 mole % CnHn+i (n = 7). Sulfur species were not analyzed due to absorption within the chromatography system; however, a H2S concentration of 16 ppm to 160 ppm molar is estimated. The volatile content contributes approximately 50% of the microthermometrically measured freezing point depression. Cl- concentrations up to approximately 9000 ppm suggest an additional, probably magmatic, fluid component.Ascending fluids were channelled along approximately NW striking faults related to the same primary extension (17 Ma to 14 Ma) responsible for Nevada basin and range physiography. Boiling induced by CO2 effervescence led to precipitation of Au and Ag over a 150 m vertical interval. At the time, this interval was about 460 m below the water table (approximately 38 bars), but because of erosion, it is now within 90 m of the surface. A Ag:Au ratio of 25:1 has been calculated for the Dixie Zone."

Jan 1, 2000

By R. H. Colquhoun

"INTRODUCTION The Holt-McDermott Mine is wholly-owned gold mining operation of American Barrick Resources Corp. that begun operations in June 1988.The property is located 0.5 km. south of Highway 101 East in the Harker-Holloway Townships of Northeastern Ontario, 7 miles south of Lake Abitibi and 15 miles west of the Quebec-Ontario border.Employees of the operation travel daily from various communities in the area, predominantly from Kirkland Lake, Ont., which is located 65 km. to the southwest.The significance of the operation is that it is the first full scale operation associated to the Oestor-Porcupine Fault to go into full production in recent history as well as the first Carbon-in-Leach (CIL) operation in the province owing to the natural occurring carbonaceous ores that are associated to the ore body and the geological fault systems.GEOLOGYThe Holt-McDermott deposit is located in the Abitibi Greenstone Belt, a short distance west of the Ontario-Quebec border. Ore grade material follows the footwall contact of a fault zone known locally as the McKenna Fault, which is thought to be a splay off of the Oestor-Porcupine Fault, itself a major feature in the Abitibi belt.The McKenna Fault strikes approximately east-west (as does the Oestor-Porcupine) and dips to the south at sixty-five to seventy degrees. The fault lies within a package of mafic volcanic rocks (basalts). These rocks have been strongly altered and mineralized adjacent to the McKenna Fault, and the resulting lens-like ore bodies constitute the mining targets."

Jan 1, 1989

By A. S. Moghaddam

The transportation of cemented and non-cemented mine tailings in the form of paste through pipelines is one of the main stages of paste backfill operations. For the purpose of pipeline design, the rheological properties of the materials, such as yield stress and viscosity must be determined. In this study, the yield stress of two Canadian mine tailings, for gold and copper mineralization, were studied using the vane method and slump tests. The comparison between the vane method and the slump tests indicates that the slump tests generally overestimate the yield stress values for both cemented and non-cemented paste backfills. In addition, the effects of 5% Portland cement (type 10) and mixing time on the yield stress of paste backfills were investigated. The percentage of cement as a binder agent has a direct effect on the increase of the yield stress of paste backfills. Yield stress measurements show that mixing times of 4 minutes and 12 minutes have the same effect on the yield stress values.

May 1, 2007

By H. A. Bilgin, G. G. U. Aldas

"Ground vibration is the natural result of the blasting process. Many empirical formulae and methodologies including analysis of travel path effects have been developed. The scaled distance, which is the most popular approach for the calculation of the attenuation of particle velocity in the ground, has led to significant advances in the prediction of particle velocity when both explosive charge and distance vary. However, this approach does not consider the effect of ground anisotropy and existence of structural geological features on ground vibration. Therefore, in this study, the effects of these rock mass properties on types, amplitudes, and frequencies of ground vibration waves at four surface mines are examined. The results, which were implemented at Kangal coal mine, Bastas quarry and Kíbrís quarry, provided guidance for the extensive study at Orhaneli surface coal mine.As a result of the study, the authors came to the conclusion that vibration amplitudes change depending on the ground on which sensors were deployed and the conditions depending on whether measurements were done near major structural geological features. It was determined that the vibration amplitudes, measured at equal distances from the source but in different directions, change because of the propagation velocity anisotropy. Besides the change of wave type due to the kind of ground at the measurement location, it was determined that vibration anomolies were due to structural features."

Jan 1, 2004

By S. Kelebek, E. Yalcin

"Two composite samples of a gold-bearing ore from North Western Quebec (Barry Township) were tested to assess their grindability, recovery by flotation and Knelson concentrator as well as extraction using cyanidation.Work index values (BWi) for two composites were found to be 10.4 and 11.0 kWh/tonne, respectively. Flotation tests involved feed samples for which the particle size ranged from a P80 value of 205 ?m to 53 ?m, which resulted in gold recoveries of 91.8% to 95.8% (at gold grades of 130 to 140 g/tonne). Cyanidation tests indicated gold extraction levels ranging from 94.2 to 97.5%. Higher, recoveries were obtained at finer grind sizes and higher cyanide strengths. However, the grind size had a bigger impact on gold leaching. Gold grade and recoveries obtained with the Knelson concentrator device were lower than those obtained by flotation. Mass recoveries to concentrate products strongly depended on the fluidization pressure used. High gold recoveries can be obtained generally at low water pressures of 3 to 4 psi. Higher water pressures produced more selectivity at the expense of higher gold losses.It can be concluded that the gold ore samples tested have good characteristics due to moderate levels of energy requirement, high gold recoveries and extraction rates attainable.INTRODUCTIONBench scale testing of ore samples is an important step in the long series of metallurgical and economic studies involved in bringing new ore bodies into production (Coleman, 1980). Through a laboratory testing program, the behaviour of an ore in a particular process on a larger scale can be established. In an exploratory manner, this testing can be helpful for classification of ores in terms of “good ore” or “problematic ore” by providing preliminary information on recoverability of target minerals. Potential problems if any can be assessed by further investigation of products (e.g., middlings) obtained as a result of testing. A detailed bench scale experimental program in the metallurgical laboratory can also provide the background work for flowsheet development. Depending on the simplicity or complexity of the ore to be tested and type of details required from a testing program, the amount of samples required in the mineral processing laboratory can vary from several kg to more than one hundred kg depending on how detailed the metallurgical testing program is."

Jan 1, 2008

By Norman A. Jull

"Factors which affect the separation achieved in a hydrocyclone are discussed and illustrated with graphs of some mathematical relationships.Definitions of separation and sharpness include comment on use of elutriation devices.A plea is made for better evaluation of field data prior to their reporting or use in calculations. Methods of evaluation are suggested, with samples of the relevant calculations.An example of the effect of percent solids errors is given, with computer printout and plotted corrected recoveries.INTRODUCTIONThe range of interest in cyclones runs from a simple demand for classification results to a detailed study of published equations defining cyclone characteristics. Probably this group covers as broad a range and, in an attempt to offer something for everyone, I will begin with general operating comments, then move on to more analytical topics. Ideally, an author would compose his paper after the discussion period, when he would have a better idea of the areas of special interest to his audience.Sor'1e of you may share our incurable fascination with classification, especially as performed in cyclones. It is amazing that such a simple device could be in use for more than 20 years and retain as much mystery as it does. Substantial parts of the mystery have been solved but some remains, to keep up our curiosity. There is at least one valid reason: the unusual compactness of this device, which makes internal observation very difficult. What other unit can you think of which performs such a complex separation between particle sizes, shapes and specific gravities at such high capacity? Retention time in a cyclone is typically 3 seconds!Mutual Agreement - In a cyclone, every parameter of geometry and of operation interacts with every other. In an orderly discussion of individual parameters it would be necessary to repeat, in every section, 11 if all other factors are equal"". Could we agree now, for our mutual convenience, that that phrase is clearly understood between us during the remainder of this paper?"

Jan 1, 1972

By G. Papachristodoulou, O. Trass

"Performance data for both wet and dry grinding of materials have been obtained in this novel, planetary ring-roller mill over wide ranges or operating conditions. The Szego mill consists of a stationary cylindrical shell inside which grooved, radially mobile rollers rotate, driven by a central shaft. The mill has several internal design variables such as number, diameter and length of rollers as well as size, shape and pitch oi helical grooves. It is compact, has a high specific capacity, modest power consumption, and can grind many materials down to ultrafine powders. Illustrative data on product fineness and mill power consumption are given along with results from studies on grinding kinetics.INTRODUCTIONThe extensive use and importance of grinding as a unit operation, coupled with the rather low energy efficiency of conventional equipment provide a challenging incentive to investigate novel methods of comminution. Yet, most current development work is taking place in mill performance modelling and optimization, or with various detailed improvements rather than in the field of new equipment development.This paper is a report on the development of a ring-roller mill invented by the late L.L. Szego which embodies several novel concepts. The mill has a broad range of applications, may be operated wet or dry, and can grind materials down to ultrafine sizes with modest energy consumption. It has been developed by General Comminution Inc. in close cooperation with the University of Toronto."

Jan 1, 1986

By J. S. Phipps, D. R. Skuse

"Aqueous slurries of fine particle size calcium carbonate are used in a diverse range of end-use products. In many cases, the end use performance is governed by the fineness of the particle size distribution. In turn, the maximum fineness of the particle size distribution is primarily determined by the efficiency of the dispersants used during the production process. Here we report the sodium polyacrylate mediated dispersion of calcite and kaolin. Firstly, we report a colloid chemical description of the dispersant behaviour and attribute the stabilisation to both steric and electrostatic mechanisms. Secondly, we describe how the understanding developed in the first part of the study can be utilised to produce more effective dispersant systems which allow the preparation of, added value, higher solids and finer particle size calcium carbonate slurry products.INTRODUCTIONConcentrated aqueous dispersions of fine, particulate kaolin and calcium carbonate are used extensively in the coating of paper. Currently more than 10 million tonnes of such dispersions are used annually in North America and Europe alone, and worldwide consumption is growing at around 3% per year.Generally, paper is coated to enhance its visual appearance. Firstly, coatings improve the optical properties of the blank sheet, i.e. its brightness (or whiteness), opacity and gloss. Secondly, they improve the physical properties of the sheet that will influence the quality of the final printed image, such as surface smoothness, porosity, and ink absorption. In order to achieve these aims economically, paper coatings must be applied at high speeds and with minimal drying costs.Kaolin and calcium carbonate pigments are the major components of most paper coating formulations. Particle size distributions are chosen to maximise the optical benefits that they confer, and to allow the production of formulations that can be easily pumped, handled and coated. Coating pigments are generally produced and transported as slurries, and so it is important to obtain dispersions with the highest possible solids content, both to minimise drying costs and the quantity of water transported. This paper examines the dispersant technology that is currently used in the industry and the mechanisms by which it functions, and illustrates ways in which this technology has developed and could be further improved in the future."

Jan 1, 2003