Search Documents

By Lawrence Devon Smith

What is a Failed Project? For mining projects, some key indicators of a ?failed? project are: ? Cost is more than it should be (particularly capital) ? Schedule ? It takes longer to build than expected ? It takes longer to ramp-up than expected ? It does not do what it is supposed to do ? Poor performance; output, product specifications; ? Low revenue ? High costs ? No one is happy about it: Management, Shareholders, Bankers ? Does a project fail if it does not meet expectations that were unrealistic and unattainable? ? Caution: Failure may not become evident until years later

May 1, 2010

By W. R. Cowan

The availability of mineral aggregates for construction purposes is rapidly declining through inadequate resource planning. restrictive zoning and legislation , and competing land uses. The Geological Branch of the Ontario Ministry of Natural Resources has undertaken to provide aggregate inventory reports for all townships designated under The Pits and Quarries Control Act, 1971, and eventually for all towns hips in heavily populated areas. The reports contain maps and recommendations for extractive zoning by municipalities; of necessity only the largest deposits are given priority recommendations. It is intended that these reports should improve the resource planning in areas underlain by large aggregate deposits. The inventory is only possible because a concentrated effort has been made to map the Quaternary geology of populated areas over the last ten years. Future needs require that we develop methods to determine the extent of poorly defined and buried aggregates and that we look for natural alternatives.

Jan 1, 1978

By Y. Q. Li, X. H. Long

In this work, structural and electronic properties of smithsonite (ZnCO3) and cerussite (PbCO3) as the typical lead-zinc oxide minerals is simulated by means of DFT. The calculated results could be concluded as: (1) The density of states (DOS) of Zn atom in ZnCO3 is nearer to the Fermi level than that of Pb atom in PbCO3, suggesting that the Zn atom of ZnCO3 is more active and easier to interact with water molecules and hydroxyl ions. Smithsonite, therefore, could be more readily depressed in the flotation process. (2) The bond population value of Zn-O (0.23) and C-O (0.92) in ZnCO3 is obviously larger than that of Pb-O (-0.01) and C-O (0.85) in PbCO3, indicating that the covalent characteristic of ZnCO3 is stronger than that of PbCO3. (3) It is shown that the charge of Pb (+1.32e) in PbCO3 is more positive than that of Zn (+1.22e) in ZnCO3, suggesting that cerussite is easier to interacting with HS- compared with smithsonite in the flotation process. In summary, the structural and electronic property of smithsonite is completely different with cerussite, leading to the difference of their flotation behaviour.

Jan 1, 2015

By Dong-kil Lee

A ventilation improvement index (VII) was developed in an effort to propose an optimal ventilation improvement measure for a designated mine. The index was designed to incorporate both ventilation effectiveness and cost efficiency. To verify the effect of the index, a mine experiencing a ventilation problem was selected, the ventilation assessed and ventilation network analyses were conducted. In the selected mine, four areas with ventilation difficulties were detected and an improvement schemes for each area were proposed. These were simulated through network simulation and evaluated using the ventilation improvement index. As a result, an optimum ventilation improvement scheme was proposed. The improvement scheme with the highest VII value was incorporated in the design.

Aug 1, 2013

By D. W. Tully

Sedimentary and volcanic rocks of the Timiskaming series trend west-ward across the property of the Upper Canada mine, forming part of the north limb of a regional syncline which is truncated on the south by the Larder Lake fault zone. A wide zone of schistosity strikes east-west through the sediments and volcanics. The central portion of this zone is occupied by a system of narrow gouge-filled fractures in highly altered rocks, mainly tuff, trachyte, trachyte porphyry and syenite porphyry. The alteration zones have developed through repeated stages of deformation and accompanying metamorphism. The initial stages were marked by carbonatization and sericitization, followed by silicification and the introduction of minor amounts of sulphide minerals. Gold was finally de-posited in relatively late fractures within silicified zones and pyrite. Repeated movements along the Up-per Canada break have offset post-ore dykes of minette and diabase, and have resulted in minor displacements within the orebodies.

Jan 1, 1963

By Y. Yhang, D. C. Sego

ABSTRACT This paper evaluates the potential of freeze-thaw dewatering using Albian mature fine tailings (MFT). Freezing tests were first performed to study the effect of freezing rate on dewatering efficiency. Lower freezing rate resulted in higher thawed solids content and shear strength. Subsequently, large strain consolidation tests were conducted to investigate consolidation behaviour and how it is affected by freeze-thaw. The consolidation behaviour was presented in terms of effective stress versus void ratio and permeability versus void ratio. The results can be used to predict the field behaviour of Albian MFT and optimize the application of freeze-thaw for MFT dewatering.

Jan 1, 2014

By Zdenek D. Hora

British Columbia is an important producer of a variety of industrial minerals for both domestic and export markets. Some commodities such as limestone, dolomite, gypsum, calcium carbonate, silica, barite and magnetite are raw materials for well-established industries located in British Columbia, Alberta and northwestern USA. Others, like magnesite, sulphur, jade, asbestos, dimension stone and clay products, are mainly exported in processed form to overseas customers. Companies are developing markets for relatively new mineral products, including pumice, volcanic cinder and zeolites. A number of attractive geological targets have been identified by industry while research by government geologists has outlined the potential for refractory minerals, gemstones, garnet, nepheline syenite, carbonatites, residual kaolin, igneous apatite and peat.

Jan 1, 2001

By W. A. Lang

Introduction In this review, which is the fifth of the series on the Progress in Coal Technology, an attempt has been made to outline some of the more important developments that have taken place in coal carbonization during the last decade. Research into both high-and low-temperature carbonization has been active for three principal reasons: (1) the growing shortages in most countries of high-quality coking coals; (2) the demand for smokeless fuels for domestic purposes; (3) the need for metallurgical coke for the increased output of steel in the post-war years. The growing importance of coal tars as a source of chemicals for the preparation of synthetic products and of coal gases for the recovery of sulphur is evident. Many of the researches initiated because of wartime necessity have been continued .and even expanded in the post-war years. High-temperature carbonization with a suitable coal yields a strong coke which is used primarily for metallurgical purposes, a tar with good marketable value, and a large yield of gas of medium calorific value. Low-temperature carbonization gives a more free-burning solid product suitable for a domestic fuel, a high yield of a tar which is generally regarded as superior to high-temperature tar for chemical purposes, and a smaller yield of a higher-heat-value gas.

Jan 1, 1951

By D. S. Speakman

The copper-zinc orebody at Sherritt Gordon's Ruttan Mine occurs in a structurally complex area of the Rusty Lake greenstone belt in northern Manitoba. Problems in interpreting drill results indicated a large deviation, and the structural complexity an erratic deviation, of drill holes. This was confirmed when a surface hole was intersected 420 feet to the left of line on the 800 level. This problem acted as a catalyst in promoting a search for a suitable down-hole survey method. The instruments investigated included magnetic multishot and gyroscopic units as well as the ABEM Reflex-Fotobor. Only the Fotobor came close to meeting the company's needs of simplicity, reliability, accuracy and ownership. In this paper, the methods of operating this instrument, as well as the data extraction and reduction techniques, are described. Data on the accuracy and repeatability of the instrument are presented, and a tabular presentation of the results of surveying on 86 holes totalling 64,000 feet of drilling is made. Preliminary statements of the results of ongoing research on causes of hole deviation are presented and recommendations for minimizing deviation are given. The use of the survey device is recommended in areas of structural complexity, for very steep or backsight holes and where expected ore intersections are missing.

Jan 1, 1978

By Xiang Li, Xibing Li

It is paramount that the stability of rock slopes be correctly accounted for under diverse operating and environmental conditions. Owing to different sources of uncertainty entailed in such stability problems, conventional deterministic approach through the calculation of a factor of safety (FOS) cannot reflect quantified uncertainties explicitly and sufficiently. Thus it is highly desirable to invoke the reliability approach to consider uncertainties in a systematic manner. Nowadays, the current design standards have an increasing tendency to ensure rock slope stability by pre-defining a target reliability index (or target probability of failure), viz., the reliability level of a rock slope is pre-set as a target to be satisfied. In such a situation and considering the fact that the FOS used as an indicator of slope performance still has a very wide acceptance, we focus on proposing an inverse-reliability-based methodology which aims at developing a two-fold indicator strategy, i.e., using the FOS and reliability together to deal with slope stability problems. The basic idea behind it is to utilize a so-called inverse first-order reliability method (IFORM) to directly calibrate the FOS provided the target reliability index has been given. In this way, the calibration scheme relating the FOS can be rationally done by not only incorporating uncertainties, but also satisfying a desired level of the prescribed reliability. Based on this, to make the IFORM computationally feasible and also reduce its computational cost, we introduce the response surface method (RSM) to generate a surrogate for the FOS-based limit state function (LSF), considering the lengthy and complicated form of the FOS in some recognized methods (e.g., within the framework of limit equilibrium). Distinguished from the existing RSMs that potential inadequacies may arise, we present an RSM based on a hybrid approach combining support vector machine (SVM; used as a regression technique) and uniform design (UD; pertaining to experimental design). Using a representative example of rock slope stability problem, we demonstrate the feasibility and validity of the developed methodology, during which the associated sensitivity study and further discussion are also performed. By dint of such a methodology, we can establish a link between the conventional deterministic approach and the reliability approach, where a logical and realistic framework is provided, for cases achieving the specified reliability, to assist in selecting the FOS which remains adequate for rock slope stability even in the face of uncertainty.

Jan 1, 2015

By Z. Y. Ma, H. Y. Yang

The process of microwave-ultrasound assisted leaching of valuable metals from copper anode slime was proposed in this paper. Design of experiments has been used to study the effect of the main leaching parameters, such as microwave power, ultrasound power and reaction time. The central composite design (CCD) was used to predict the maximum leaching efficiency of copper, tellurium and selenium. The experimental data obtained were fitted to a second-order polynomial equation, and they also were analyzed by analysis of variance (ANOVA). The 3-D response surface plots and the contour plots were applied to determine the optimal conditions. The optimum conditions of microwave-ultrasound assisted leaching process were: microwave power 834W, ultrasonic power 638W and reaction time 403s. Under these conditions, the experimental leaching efficiency of copper, tellurium and selenium were 98.88±0.56% 98.96±0.78% and 98.57±0.67%, respectively, which agreed well with the predicted values.

Jan 1, 2014

By K D. Conroy

For the past year, Lowphos Ore Ltd. has been operating two desliming hydroseparators on a fully automatic basis. Automatic operation is achieved by sensing the position of the silica-magnetite interface and automatically controlling the jet water addition to maintain a desired interface position. The system further provides automatic control of the underflow pump speed in order to assist in maintaining interface position when an <Ore change occurs. Interface position is maintained at 12 inches below the surface and is -controlled within plus or minus one inch. Metallurgical unit recovery is held above 98.5 per cent, and a 10 to 12 per cent increase in concentrate grade is normally achieved.

Jan 1, 1963

By C. K. Wilton

"The Agnew Lake uranium deposits were discovered in 1953 following the discovery of the Elliot Lake deposits to the west. The original property was optioned to Kerr Addison Mines Limited who added additional claims by staking. Agnew Lake Mines Limited was incorporated in 1967 to develop the property and a shaft was sunk to 1040 metres and five levels developed before work was suspended due to low uranium prices at the end of1970.In 1974-75 the mine was dewatered and production started in 1977. By 1978 reserves were estimated at 10,000,000 tonnes averaging 0.35 kg. U10 , per tonne. Underground operations were terminated in 1980 although a uranium leaching operation was continued until early 1983.The deposits lie near the contact of Huronian metasediments with underlying Algoman granite. The sediments consist of arkose, conglomerate, argillite and quartzite with the uranium mineralogy mainly confined to oligomictic quartz pebble conglomerate. The higher uranium values are related to conglomerate with highest percentage of pebbles. The chief uranium minerals are uranothorite and monazite. It is of interest that the uranium thorium ratio differs appreciably from that of the Elliot Lake deposits. This fact along with the fact that the Elliot Lake sediments were deposited by paleocurrents from the northwest whereas the Agnew Lake sediments were deposited by paleocurrents from the northeast indicates widely separate sources for the deposits. It is suggested that the Agnew Lake uranium deposits are syngenetic placers deposited under anoxygenic atmospheric conditions."

Jan 1, 1986

By Roger Lacroix

L?arrivée de nouvelles technologies sur le marché des foreuses portables combinée au besoin des mines à mieux consommer l?énergie électrique ont permis d?identifier le potentiel de deux nouveaux type de foreuses présentement utilisées en Afrique du Sud, à savoir les foreuses électriques et les foreuses hydrauliques actionnées à l?eau. Grâce à la collaboration de mines Niobec et Géant Dormant de Cambior Inc., ainsi que d?Hydro-Québec, le potentiel réel d?économie énergétique des foreuses portables hydrauliques et électriques par rapport aux foreuses conventionnelles à air comprimé a été évalué pour des roches dures et moles. Ainsi, cet article a pour objectif d faire ressortir ces potentiels d?économie énergétiques. En outre, les résultats pour une mine mécanisée et une autre mine de type filonien, dans lesquelles on retrouve des conditions de terrain différentes, seront présentés. Les résultats montrent un potentiel d?économie énergétique d?environ 70% pour la foreuse électrique et d?environ 50% pour la foreuse actionnée à l?eau. Ces résultats montrent qu?il est possible d?obtenir une meilleure efficacité énergétique par mètre foré. Ainsi, il apparaît maintenant intéressant de poursuivre les travaux de développement des deux technologies pour les applications de forage vertical et de tensionnement des boulons, et de viser à accroitre le taux de pénétration de la foreuse électrique pour le rendre équivalent à celui de la foreuse à air comprimé.

May 1, 2007

By J. E. Nesset, F. Rosenblum, J. A. Finch, R. Payant

ABSTRACT Under certain conditions of moisture and oxygen, sulphides can spontaneously self-heat. We tested a hypothesis that galvanic interaction between some sulphides can promote self-heating. Galvanic interaction is controlled by the rest potential difference between sulphides and particle size. A series of binary sulphide mixtures was tested. Individual sulphides and mixtures with low rest potential difference did not self-heat, but mixtures of high rest potential difference did. When testing pyrite-sphalerite mixtures, self-heating increased inversely with particle size, with the fineness of the pyrite governing self-heating, indicating the rate-limiting step is the reduction reaction. The results support the hypothesis that galvanic interaction contributes to sulphide self-heating. A possible mechanism based on hydrogen sulphide as an intermediate product is proposed. The understanding gained will be of interest to those involved in storage, shipping, and disposal of sulphides.

Jan 1, 2012

By R. I. Cavanagh, A J. Last

THE USE of higher grade charges in blast furnaces in the form of sintered or pelletized concentrates has been increasing rapidly. The question of beneficiation of iron ores for this purpose is therefore receiving much attention as more deposits are developed. Many iron ores may respond well to magnetic roasting procedures followed by magnetic concentration, however, in most cases other more standard ore dressing methods are competitive and cheaper. For magnetic roasting as applied to iron ore beneficiation, the present question is "Can it be economically justified in situations where it appears to produce good results?" The following collection of information on the general status and operations of magnetic roasting methods may be helpful in considering this question. Magnetic Roasting Magnetic roasting involves the transformation of non-magnetic iron oxides, hydrated oxides and carbonates by means of heat and suitable

Jan 1, 1961

By E. L. Chanturiya

The research and characterisation for compositional, physicochemical, structural, electrical and flotation properties of various pyrite samples for a copper-zinc sulfide ore was carried out. Various methods were used during the research, such as optical microscopy, X-ray diffraction, electron probe micro-analysis (EPMA), phase emission analysis, routine chemical analysis, auger electron spectroscopy (AES), scanning electron microscopy (SEM), back-scattered electron images (BSE), potentiometry, and instrumental neutron-activation analysis, flotation. Analysis of obtained results established the interrelation between impurity structures and concentration of electric charge carriers in minerals, Butyl xanthate sorption and flotation yield of pyrite. The research concluded that pyrite samples differ by morphology, micro defects of structure, concentration of donor and acceptor impurities (Co, As, Sb, etc.) and conductivity parameters (thermo-electrical force, specific resistance and concentration of charge carriers The peculiarity of pentagon-dodecahedral pyrite is the high concentration of electric charge carriers (electrons) and the more negative surface potential (by 25–75 mV) in comparison to cubic pyrite. The surface of cubic varieties is more active, therefore it is oxidized in alkaline lime medium much faster, than the surface of pentagon-dodecahedral varieties. This phenomenon is caused by high reaction ability, irregular jointing and defects of cubic pyrite. This promotes the increase of calcium ion sorption on its surface and the decrease of Butyl xanthate sorption. According to this, an increase in alkalinity (lime medium) from a pH of 10.0–11.5 leads to an increase of gold content reporting to the tail of bulk flotation. Gold content is increased from 0.58 g/t (?? 9.5) to 1.9 g/t (?? 11.6), which represents an increase in gold recovery of 24.68 to 79%, respectively.

Jan 1, 2016

By P. Trudel, M. A. . Cloutier

This lithogeochemical study demonstrates that the Gilman and Blondeau Formations in the Chibougamau area belong to a subalkaline suite of tholeiitic affinity poor in potassium. The Gilman Formation is composed mostly of basalts, with subordinate andesites and rare dacites, while the Blondeau Formation comprises all lithologies of the basalt-andesite-dacite-rhyodacite-rhyolite ensemble. Both AFM and Harker variation diagrams show that all these rocks originated by differentiation from the same magma reservoir, and are related to one volcanic episode, This study did not, however, identify hydrothermal alteration zones useful for regional geochemical prospect ion.

Jan 1, 1984

By Philippe Caudal

This paper presents a case study in which a slope failure was observed on the west wall of the LAB Chrysotile mine in the vicinity of the main ramp in January 2010. Airborne LiDAR results were used to evaluate slope geometry before and after the failure occurred. Back analysis of the failure was performed to assess rock mass properties at the slope scale using various numerical techniques: limit equilibrium, finite elements and fracture networks. The various approaches correlated well with field observations.

Aug 1, 2013

By J. Kalynchuk, R. Poulin, R. Pakalnis, D. Peterson

"A market survey of all underground mines in Canada (Fig. 1) was completed to determine the ex1ent to which cable bolts are being used as ground support. One hundred and nine questionnaires were distributed with 65% of them being returned completed. As a result, the quantity, types and locations of cable bolt installations have been determined. In addition, the grout pumps used, time required and cost of installations have been addressed. The popularity of other support types used in underground mines is summarized.IntroductionRock reinforcement consists of installing support within the rock mass (internal) or within the excavation (external). Within the past twenty-five years several new types of ground support have been introduced within the mining industry. Cable bolts were first introduced to the Canadian mining industry in the 19605 (Gramoli, 1975).Cable bolts have gained increased acceptance as a method of ground support during the past decade. The cable bolt is comprised of one central wire surrounded by six slightly smaller outside wires and typically having an over-all diameter of 15.2 nun to 15.9 nun (0.6 in. to 0.625 in.). The cable wires are made from high-strength steel with an ultimate strength of 26 tonnes (58 000 Ibs) (Goris, 1990). Current cable bolting practice consists of cement grouting one or more steel cables within a drill hole in order to reinforce the surrounding rock mass. Cable bolts are a form of internal support and are generally used in open stoping and cut-and-fill mining methods (Fig. 2).They can be either tensioned (active support) or untensioned (passive support) and may be of any length, though for underground mining applications, they are generally less than 20 m (65.5 ft) and are untensioned. A major advantage compared to previously used ground support is that the cables are flexible and can be coiled to approximately 1 m (3.3 ft) diameter coils allowing relatively long support to be installed in areas with limited head room (1.8 m).With the advent of bulk mining methods which require comparatively large stopes, it has necessitated the use of relatively long support tendons to stabilize the large spans being created. As a result, the use of cable bolts for ground support in mines has increased significantly within the past decade."

Jan 1, 1995