Search Documents

By Pier-Olivier Devin, Daniel Hodouin, Maryam Sadeghi, COREM, Claude Bazin, François Lavoie

"Spiral concentrators are used for processing coal and heavy minerals such as it is the case for the concentration of iron oxide from light silica gangue. The concentration process for iron ore usually consists of a rougher bank of spirals followed by two stages of spiral cleaning. The process control applied to the concentration circuit aims at maintaining a target iron content of the final concentrate and is mainly conducted by adjusting the wash water addition and the position of the splitter gates at the discharge of the spiral. This paper describes the use of a simulator to study control strategies for a gravity concentration circuit using spirals.INTRODUCTION The Canadian iron ore mines are located in the Northern part of Quebec and in Labrador (Neal, 2000). These iron ores consist mainly of hematite with some ore bodies rich in magnetite and ilmenite. The processing of the coarse hematite iron ore consists of the extraction from an open pit mine, followed by the conventional crushing and autogeneous grinding of the ore to obtain a particle size smaller than 1.2 mm. The ground ore assaying 40% hematite (Fe2O3) with quartz (SiO2) as the main gangue is processed by spirals to produce an iron oxide concentrate assaying 90 to 95% hematite.Spirals separate the particles according to their specific gravity and size (Burt, 1984; Bazin et al., 2014). These environment friendly devices have been used for decades and are still used for the preparation of coal and for the concentration of heavy minerals such as iron oxide (Staff, 1977; Wills, 1992). However very little information is available concerning the control of gravity concentration circuits. This paper analyzes the control practice of a gravity concentration circuit using a simulator. The paper consists of 3 sections. The first section describes the operation of spirals and spiral concentration circuits. The second section briefly describes the simulator and shows some simulation results for a gravity concentration circuit. The third section shows the application of the simulator for the study of control strategies for a spiral concentration circuit."

Jan 1, 2016

By A. J. Miller

Estimates of interstitial water saturation derived from capillary pres-sure data are compared with residual water saturations found by the analysis of cores out in oil-base drilling fluid. A theoretical explanation for the high-rate of water production from the Bellshill Lake Field is proposed, based on the interpretation of the capillary pressure data.

Jan 1, 1960

By M. Kamyab

Transportation of fluid and slurry (fluid and solid particle mixtures) in a pipe and annulus space has been the focus of numerous studies. There are different parameters to be considered when studying slurry transportation. These include slurry velocity or flow rates; fluid properties such as density and rheology; and solid particle properties including concentration, density, shape and size. Also the angle of the flow conduit, rotation of the pipe and possible eccentricity of the annulus are other factors which influence slurry transport characteristics. Although a number of analytical, numerical and empirical equations as well as numerical simulations have been developed for studying the flow and slurry transport characteristics, the results need to be validated against either field or lab data. As performing field tests is costly and time consuming, conducting simulations at the laboratory scale appears as a good alternative. Different flow loops have been designed to study slurry transport behaviour in different science and engineering disciplines including oil and gas and mining. However, few of these consider, in particular, cuttings transportation in small size annulus space. The flow characteristics appear to be very different when slurry travels within a small size annulus, in particular when the fluid velocity is high. In this study, a review of some of the existing slurry flow loops will be conducted. Then the details of a slurry loop, which has been designed and commissioned for the purpose of studying cuttings transport in a small size annulus space for applications in drilling mineral exploration wells using coil tube technology, will be presented.

Aug 1, 2013

By M. B. Kime

"A set of experimental batch leaching tests studied the effect of pH, time, temperature, and stirring speed on the relative Cu, Co, Ni, and Fe leaching yields of an oxidized copper-cobalt ore sample in an aqueous hydrochloric acid solution. The results were statistically analyzed and modelled using the structural equation modelling method. Models showed that Cu, Co, and Ni leaching yields were strong functions of the leaching time and leaching temperature, whereas the Fe leaching yield depended on the leaching temperature, stirring speed, and pH. Under optimum leaching conditions yields were 99.8% Cu, 82.4% Co, 91.3% Ni, and 30.6% Fe.RÉSUMÉ Une série d’essais expérimentaux de lixiviation en bâchée ont été menés pour étudier l’effet du pH, de la durée d’attaque, de la température et de la vitesse de brassage sur les rendements relatifs de lixiviation du cuivre (Cu), du cobalt (Co), du nickel (Ni) et du fer (Fe) d’un échantillon de minerai de cuivre-cobalt oxydé dans une solution aqueuse d’acide chlorhydrique. Les résultats ont été analysés et modélisés statistiquement à l’aide de la méthode de modélisation par équation structurelle (SEM, de l’anglais structural equation modelling). Les modèles ont montré que les rendements de lixiviation du Cu, du Co et du Ni dépendaient énormément de la durée d’attaque et de la température de la lixiviation ; le rendement de lixiviation du Fe, quant à lui, dépendait de la température de la lixiviation, de la vitesse de brassage et du pH. Dans des conditions optimales de lixiviation, les rendements étaient de 99,8 % pour le Cu, de 82,4 % pour le Co, de 91,3 % pour le Ni et de 30,6 % pour le Fe. INTRODUCTIONThe Katanga province in the Democratic Republic of Congo hosts the northwestern part of the Central African Copperbelt. This region abounds with large, rich deposits of sulfide and oxidized copper-cobalt ores. In general, the main valuable minerals present are malachite (CuCO3Cu(OH)2) and heterogenite (CoO(OH)). Common impurities found in heterogenite are Cu, Ni, Si, Al, Mn, and Fe. The substitution of Co by other cations (e.g., Cu, Ni, and Fe) has an influence on the crystallinity of heterogenite (Deliens, 1974). In general, well-crystallized varieties of heterogenite have lower impurity contents, whereas amorphous heterogenite types usually contain more impurities (Thys et al., 2009). Further, in heterogenite, Co can occur in the 2+ and 3+ oxidation states. The gangue generally consists of quartz (SiO2), talc (Mg3Si4O10(OH)2), kaolinite (SiO2·Al2O3·2H2O), limonite (Fe2O3·3H2O), and goethite (FeO(OH)). Oxidized copper-cobalt ores are often treated by hydrometallurgical methods, whereas sulfide ores are often treated by flotation or pyrometallurgy, depending on their grades. Hydrometallurgical methods typically entail selectively dissolving the metals of interest (Cu, Co, and Ni) in aqueous solutions (leaching), transferring the dissolved metals to an organic solution, and retransferring these to a second aqueous solution (solvent extraction). Copper and nickel are readily dissolved in an acidic aqueous media. In contrast, cobalt is difficult to dissolve, especially if it is present in the third oxidation state; however, this species becomes soluble after it is reduced to Co2+ (Mwema, Mpoyo, & Kafumbila, 2002; Kime & Makgoale, 2016)."

Jan 1, 2017

By J. W. Gregg, P. M. Dranchuk, D. L. Flock

"From preliminary investigations it has been observed that although evaporation losses may be estimated by comparing single values of certain physical properties of crude oils and their evaporation residues, such techniques possess little accuracy unless both the evaporation process and the variation of the property as a function of the process are completely known. The accuracy of estimation may be increased somewhat through the comparison of property mid-per-cent curves. Further increases in accuracy are possible if bottoms yield •curves rather than mid-percent curves are used. The use of both the mid-percent and bottoms yield curves however involves a prohibitive amount of effort in most cases. Examinations of distillation bottoms from Hempel type distillations carried to end points just short of the cracking point have indicated that these bottoms are not appreciably affected by the evaporation process. It was further observed that bottoms of identical API gravity, obtained from a crude oil and its evaporation residues behave as if they were pure components which were unaffected by evaporation. Based on these observations Hempel distillation bottoms of equal API gravity were obtained for a crude oil and its various evaporation residues from API gravity bottoms yield curves. The volume percent of these bottoms in the crude oil and its residues were used to calculate the evaporation losses suffered by the crude in order to yield the various residues. The results indicate that, although further refinements in technique are required, it is possible to calculate evaporation losses with an accept-able degree of accuracy through the use of this method."

Jan 1, 1960

By Wm. D. Jr. Sheldon

THIS paper presents practical data to aid in the selection of a mine ventilating fan, and outlines considerations to be made to ensure satisfactory operation and optimum efficiency of the fan. Much has been published on the general subject of mine ventilation, but the writer has found few specific data on factors and considerations which govern the selection of a fan-data which should be available to the operator if his fan is to give satisfactory service within the range of the high-efficiency portion of its performance curve and deliver the specified air capacity when operating against the anticipated range of resistance of the mine. The total quantity of fresh air furnished by the ventilation system must be adequate to provide, and to ensure at all times, safe and healthful working conditions in the mine. It is assumed that the mine operator is able to determine the air quantities required for the various parts of the mine.

Jan 1, 1941

By M. S. Badollet

"IntroductionASBESTOS FLOATS may be defined briefly as blends of air-borne particles of fibrous asbestos and dusts produced during the milling stages and collected by Cottrell precipitators, dust sheds, or bag-houses.The various grades of asbestos floats on the market contain fibrous asbestos particles ranging in length from microscopic to approximately 1/4-inch. The fines or dusts present in the floats are from 40 microns to 2 microns or less in cross-section.Airborne asbestos particles are of diverse length because they are collected at numerous places in the mill. There are: (1) dusts removed from dry rock storage bins, (2) dusts removed from rock and fiber screens, (3) particles from the tops of collectors, and (4) fines removed by suction from the processing equipment. Sometimes the airborne particles are kept segregated, so that there is a partial separation by gravity. This is accomplished by a series of dust chambers enclosed in a long, rectangular building. The longest and heaviest particles fall nearest to the air flow entrance, the smallest at a point farthest away and nearest the exit. Sometimes the air from the dust chamber building is passed through a series of bag-houses or electric :precipitators ,to collect the extremely fine particles which normally escape to the atmosphere."

Jan 1, 1952

By T. Mulpeter, G. Deschênes

Sadiola Gold Mine is an open pit operation located in Mali and owned by Anglogold Ashanti Ltd, Iamgold Corporation and the State of Mali. A conventional cyanidation process (cyanidation/CIP) treats 15,000 tpd (of a mixture of oxide and sulphide ores) at an average grade of 3 g/t Au. In 2002, the increasing tonnage of sulphides caused an increase in production costs and a decrease in gold extraction (from 95% to 70-76%). Because of the short retention time of the leach circuit (18 hours) and the refractory nature of the sulphides, gold leaching kinetics are critical. A laboratory investigation was initiated to evaluate actual plant practice and identify a means of improving the gold leaching rate. The study was conducted on a "soft" sulphide gold sample containing 4.96 g/t Au, 0.4 g/t Ag, 2.5% pyrite, 1.2% arsenopyrite, and 0.2% pyrrhotite with a P80 of 74microns. Pre-leaching significantly influenced the gold leaching rate. A short pre-leach (2 hours) performed at pH 8, a DO of 8 ppm, and with 300 g/t lead nitrate added at the start or the end, produced the preferred conditions. Pre-leaching for more than 2 hours was detrimental to gold extraction. The cyanide concentration had to be maintained at 450 ppm NaCN to reach a maximum gold extraction within the retention time of the circuit. A maximum extraction of 81.3% Au was obtained in 20 hours (leach residue at 0.97 g/t Au). A high level of dissolved oxygen in the pre-leach was not of any benefit. Extension of gold leaching beyond 20 hours indicated that all leachable gold had been extracted by that time. Plant modifications were made to allow leaching of oxides and sulphides in separate circuits. Treatment of oxide ores is now performed at a higher rate. Sulphides are processed at a lower throughput, with 300 g/t lead nitrate, to allow a retention time of 22 hours. Combined throughput remains the same, and total gold recovery has increased from 76% to 80% for an additional gold production of 16,000 ounces per year.

Jan 1, 2005

By G. Gabra, M. Nagamori, J. J. Panneton

"RESUMELa calcination contrôlée de 10 serpentine permet de produire de 10 magnésie active. Le degré de I'activation est mesure par 10 solubilité du magnésium dans les acides faibles tel que I'acide acétique, La serpentine contenue dans les résidus d'amiante du Québec peut donc être activée par calcination. Le teneur en magnésie active des rejets d'amiante calcinés est fonction de divers paramètres: température, temps de calcination, granulométrie, etc. Les rejets d'amiante de différentes provenances démontrent des comportements thermochimiques différents qui sont étudiés dans Ie présent travail au moyen d'ATD, de TG, de la diffraction des rayons X et de la lixivation par l'acide acétique. On constate qu'un maximum d'environ 80% de la magnésie totale peut être activé dans certains rejets d'amiante du Québec et Ie degré d'activation dépend de la provenance.vIntroductionOn sait depuis longtemps que la serpentine, Mg3Si2O5(OH)4, un silicate hydroxylé de magnésium, devient amorphe lorsqu'elle perd de I'eau d'hydratation entre 600 et 700 °C. La serpentine ainsi calcinée est alors dissociée en magnésie et en silice. Cette magnésie, dite active, est soluble dans un acide faible ou même dans les solutions de sels d'ammonium.Plusieurs precédés chimiques ont été proposés afin d'extraire sous forme de composés magnésiens la magnésie de la serpentine. La plupart de ces procédés comportent une activation par calcination de la serpentine préalablement à une Iixiviation par un acide ou par une solution d'un sel d'ammonium.Malgré la contamination par Ie fer et par d'autres éléments, les compositions chimiques des rejets de différentes mines d 'amiante du Québec, présentées au tableau 1, sont très proches de la serpentine typique. Puisque Ie degré d'activation de la magnésie varie grandement d'une serpentine à I'autre lors de la calcination, la première étape de la recherche sur la transformation chimique des rejets d'amiante du Québec se résume à une étude de leurs comportements thermochimiques."

Jan 1, 1982

By John C. Leighton, C. O. Brawner, Doug Stewart

"Despite the availability of established, sophisticated methods for planning and designing stable slopes in rock, comparatively little attention is usually paid to the problems of carrying out the excavation. Blasting should be carefully planned to obtain optimum fragmentation as well as steep, stable working and final pit walls. The principal difficulty facing a blast designer is the lack of prior information about the many critical blasting characteristics of the rock mass. The common practise of trial-and-error lasting will eventually lead to a suitable program, but must be repeated time after time in variable geology. This frequently results in many blast-damaged slopes. Recent research indicates that monitoring drill performance will yield a Rock Quality Index which correlates to a Powder Factor value. The drilling can provide a continual supply of data, reflecting changes in the rock mass which enables the selection of an economical powder factor.IntroductionWhen planning to excavate a large-scale rock slope, engineer s will generally spend considerable effort to produce a safe, feasible and economical design. Much time will usually be spent on the field map ping, 'structural geologic studies, surface and subsurface hydrology, determination of strengths and effective friction angles of discontinuities, and finally checking stability with the aid of mathematical and analytical models. If the rock cut is to be along a transportation corridor, the prime justification for this time and effort is to produce a clean, stable slope which will be safe for those travelling or working beneath it. For the walls of an open-pit mine, there is the additional economic incentive to maintain the steepest stable slope angle for the minimum stripping ratio (Stewart and Kennedy)."

Jan 1, 1982

By Arun Verma

Thermal energy storage offers a means of effecting significant costs savings and conservation of premium fuels. Na2SO4 has been found to be a good material for storing thermal energy in the medium-temperature range, mainly because of its dimorphic nature and high heat of transition. Basic data and development of the salt to a practically usable block are discussed.

Jan 1, 1978

By L. E. Djingheuzian

"IntroductionDURING the past two decades an enormous amount of empirical data has been accumulating on grinding. These data have been obtained by mill operators on grinding ores with a diversity of characteristics, and generally they have been published. However, whenever an operator, who has started milling on a new ore, has tried to find a case in literature which would exactly fit his particular grinding problem, he has failed. Evidently, something fundamental has been lacking in all these empirical data, and, as a consequence, each new operator has had to undertake his own experimenting, get the best results he can, maybe publish these results, and let it go at that. This, in the writer's opinion, has been• due to the fact that even the ablest and most inquisitive millman has been forced to look on grinding as an art, and so, except very rarely, has not been able to find the time to stop and think; if he did so, it was rather in a philosophic way, that grinding is a fundamental process, a process that takes place in river beds, on the sea shore, etc.Nevertheless, when all the data so far published are correlated and examined as a whole, one is struck with the advances that have been made in grinding. The writer (7) had made such a study in 1949, and, when the correlation was completed, it showed that there was nothing heterogeneous about the accumulated data and that when brought together they were in harmony with each other. The writer's conclusion was that, if grinding criteria were defined and were expressed in such a way as to make integration of any data into basic formulae possible, grinding would be established as a mathematically exact science, and grinding worries of the harassed mill operator would be at an end!The first attempts to rationalize comminution were made by Rittinger and Kick. However, their theories led to endless disputes which did not accomplish much, except possibly clearing the path for subsequent investigators."

Jan 1, 1952

By lchimura. R. .

Japan Oil, Gas and Metals National Corporation (JOGMEC) and Centro de Investigation Minera y Metalurgica (CIMM) commenced a five year project from 2001 to modify the treatment of the furnace dust from Teniente converter containing harmful elements like arsenic and lead. The project was supported by Japanese and Chilean governments, and a demonstration plant was installed and operated at Las Ventanas Smelter and Refinery (Division Ventanas CODELCO). The basic and detailed engineering was made by Mitsui Mining and Smelting Co., Ltd (MMS) based on the joint study among JOGMEC, CIMM and Division Ventanas CODELCO. Arsenic in flue dust is lixiviated by sulfuric acid and fixed as crystalline ferric arsenate, where leachability of arsenic will be lower enough than the regulation, 5mg/I by TCLP (Toxicity Charactaristic Leaching Procedure) of USEPA. On the other hand, the recovered copper from the dust will be fed to the copper production process at Las Ventanas Smelter and Refinery, while zinc will be recovered as the exportable product. As introducing the crystallization and growing stage, the stable crystalline ferric arsenate formation can be achieved under the normal pressure.

Jan 1, 2007

By D. J. McLaren

"Arctic Canada is one of the largest undeveloped terrains remaining in the world, and is in many ways unique. The ecological balance of the region is more delicate than tropical or temperate regions of similar size. This region is likely to be developed by research for and production of resources, primarily petroleum, in the immediate future. As well as sensitive terrain surface caused by permafrost in some areas, many large and small mammals and birds are also in a delicate balance with the environment. Small changes in this balance can have large effects.The probability of finding petroleum in different regions varies widely, but already there are good indications on the mainland and in the Islands that both oil and gas are present. Geophysical work in the offshore, particularly the Beaufort Sea, suggests further promising potential. Possible reserves in the Islands and mainland Arctic may amount to 50 or more billion barrels.A responsible approach to problems facing exploitation in an Arctic environment includes the careful monitoring by industry of likely effects of their activities. The Mackenzie Valley Pipeline Research Association test loop at Inuvik provides an example of such monitoring. Outside Canada, the operations at Prudhoe Bay on the north coast of Alaska show how major companies may operate responsibly and reduce environmental interference to a minim'.::at. Nevertheless, four variables must affect any decisions to be made concerning energy resource exploitation in the Arctic. These are man's need for energy, economic and industrial pressures to develop energy sources, the desire to preserve a deteriorating environment, and the role of government as representing all individuals in the country and their several points of view. Factors that must be taken into account in making any decisions include the importance of Canadian oil in a world picture, the need for alternative sources of energy in the near future, the depletion of nonrenewable resources at an accelerating rate and the increasing awareness that the major problems facing man have no direct technical solution and that social or political decisions must precede further techno-logical development."

Jan 1, 1971

By Jacek Paraszczak, Stefan Planeta

"RésuméDans la première partie de cet article on discute Ie contexte technico-économique de l'usage des foreuses à l'eau sur béquille dans des mines sud-africaines. Par la suite on présente les résultats d'une étude comparative du forage avec les foreuses à l'huile et à l'eau par rapport aux foreuses pneumatiques. La performance des foreuses est discutée sous les deux aspects: l'aspect technique concernant Ie taux de pénetration et la quantité d'eau rejetee dans les galeries et l'aspect de fa santé et sécurité au travail, et plus particuliérement, les niveaux de bruit et de vibrations ainsi que Ie brouillard de l'huile. On conclut par l'évaluation du potentiel de forage à I'aide des foreuses hydrauliques dans Ie contexte canadien.AbstractIn the first part of this paper the technical and economical aspects of water-powered drilling are discussed. This technology, originally employed in South Africa, received some interest from Canadian mine operators. In this context a comparative experimental study of pneumatic and hydraulic (oil- and water-powered) jackleg drills has been realized. The performance of the drills is compared and the results reviewed with regards to technical aspects (penetration rate, amount of water spilled) as well as health and safety considerations (noise and vibration level, presence of oil mist). The potential for application of hydraulic jackleg drill is discussed."

Jan 1, 1995

By Ian Hattie, Mark R. Wilson, T. Kurtis Kyser, Brian W. Janser

Petrographic, chemical and isotopic compo itions of auriferous and non-auriferous quartz vei ns from the Sta r Lake and Flin Flin-Amisk Lake areas of northern Saskatchewan indicate diver e origins fo r the fluids associated with gold mineralization. In the Sta r Lake area, the metavolcanic , Star Lake pl uton, and heared mafic dikes have retained their original igneous 81 80 values. The 81 80 value of quartz from mi neralized veins vary by I per mi! and range from+I0 to+IJ. The only quartz ample having a 81 80 value outside th is range came from a vein not associated wi th a dike or gold mineralization . Quartz from the Star Lake pluton has identical 8180 value to the qua rtz from mi neralized vei ns which suggests that the vei ns and the pluton are related to imilar proces es. The diffe rence in 81 80 values between mi neralized and barren vein may erve a a potential exploration tool in this area. Because o34S val ues of a limi ted number of amples of pyrite from gold-bearing quartz vei ns at Star Lake correlate directly with gold content. the gold may have been syngenetic with the su lphur and the 834 value may be useful for exploration . 8180 values of co-existing quartz, calcite, and amphibole in the veins from Star Lake indicate that isotopic disequilibrium among the minerals is common, but the val ues also record a high temperature of formation (ea . 500°C) involvi ng a component of magmatic fl uid. TheoD value of hydrou mineral from Star Lake retain their original igneous values but whole rock values are generally much lower, an effect attributed to interaction of the minerals with a late meteoric water. In the Fl in Flin-Amisk Lake area, auriferou and barren quartz veins formed from a mixture of hydrothermal and metamorph ic flu id at lower temperatures (ea . 350°C) than those at Sta r Lake. Becau e there i no apparent correlation between 8180 values of the quartz with gold content or relative age of the vein , nor between the 834S val ues of pyrite and gold content, table isotopes appear limited as an exploration tool in the Fl in FlonAmisk Lake areas.

Jan 1, 1986

By Horst Konig

This paper illustrates that, with the application of new processes, smaller steel plants using local raw materials can be economical and advisable. It also introduces the problems connected with the direct reduction processes, which use non-coking coal or gas as reducing agents, and which are employed in connection with conventional reduction to produce excellent results. Electric smelting is also discussed, and some practical examples of operating plants are given.

Jan 1, 1970

By E. G. Leonardon

The question of geophysical prospecting is one that is beginning to occupy a pre-eminent place in the minds of those actively concerned in the discovery and exploitation of ore deposits. This is in marked contrast to the reception accorded such ideas when the Junior author, six and a half years ago, began introducing electrical prospectii1g to the mining fraternity on this continent. Happily, the mention of geophysics no longer evokes the sceptical and pitying smiles that it did in those days. A little reflection will show that modern geophysical methods are merely a logical development from pre-existing technique. In the study of geological problems, is it not logical to use all possible physical properties of matter? The study of crystal form and cleavage, the examination of thin sections of minerals by means of polarized light or ordinary light, in fact, utilize physical properties of minerals for the benefit of the geologist. These are, of course, laboratory methods, and the extension of the study of similar properties into field work was inevitable. This began with the magnetometric surveys, used as early as 1760 in New Jersey to locate iron ores. Eighty-four years later, John Locke's work in the United States resulted in pointing out relationships between the terrestrial magnetic field and main tectonic features of the earth's crust.

Jan 1, 1928

By Antonio Laguna

During the past few years, synthetic efforts have been addressed to the synthesis of polymeric materials with optical or semiconducting properties or even with capabilities to act as sensors for volatile organic compounds (1). The most recent studies have been concerned with the synthesis of heterometallic systems with short metal-metal interactions and the determination of their optical properties. These complexes are undoubtly interesting from a theoretical viewpoint and include an emerging class of luminescent materials, in which the observed luminescence results mainly from the interactions among the different metal centers, as well as the environments of these atoms. The understanding of the photophysics and photochemistry of these products could permit the design of complexes with appropriate metals and ligands chosen for individual applications. Following a synthetic strategy consisting on reactions between acid heterometal complexes and basic gold precursors we have succeded in synthesizing supramolecular assemblies formed via acid-base stacking, which display tunable luminescence or selective and reversible sensitivity to Vapour Organic Compounds (VOC?s) (2-5). In this sense, in accord with previous Mössbauer studies carried out in the gold precursor complex [AuR2]- (R = C6F5), the basic properties of this and related materials have been employed as building blocks of supramolecular assemblies in their reactions with complexes in wich the metallic centers act as lewis acids as, for instance, Tl(I) or Ag(I) (6). For instance, in the case of silver, by reacting equimolecular quantities of [NBu4][Au(C6F5)2] with AgClO4, in acetone, a solid of stoichiometry [Au2Ag2(C6F5)4(OCMe2)2]n is obtained. The polymeric nature of this material in solid state is confirmed through X-ray analyses (figure 1). It consists of polymeric chains formed by repetition of Au2Ag2 moieties linked through short gold-gold interactions. Nevertheless, in solution, the nature of this polymeric materials was still a matter of controversy and, in this case, the optical properties have been shown as useful tools in order to obtain information. Thus, while dilute acetone solutions of this complex give a emission coming from pentafluorphenyl localized ??* excited states, in accord with the presence of isolated tetranuclear Au2Ag2 units, when the measurements are done at different and higher concentrations, a band that does not obey the Lambert-Beer law appears. This deviation is consistent with molecular aggregation in solution of these units through gold-gold interactions, and a clear correlation between the emssion wavelength and the structure in the solid state and in solution is shown (figure 2). DFT calculations accord with the observed experimental behaviour and show the nature of the orbitals involved in each transition.

Oct 1, 2003

By N. W. Byrne

THE study of diamond drill results at the Lake Athabaska property of Athona Mines, Limited, and the co-ordination of information secured, has demanded extensive application of methods for interpreting true conditions, both structurally and from the point of view of ore outlook. This work was in charge of a capable engineer, who, as the result of exhaustive study of the drill cores, has been able to issue maps and plans exceeding the expectations of the majority of engineers and geologists who visited the field during the past summer (1935); that is, having in view the fact that staking of the property had been completed but a few months beforehand and that geological conditions were practically unknown up to the time drilling began in April. The following pages present an outline of the work of the assay and engineering offices in co-ordinating and interpreting the results of the drilling. The writer desires to acknowledge the suggestions offered by A.P. Beavan, geologist and engineer at Athona Mines, whom he assisted during the drilling campaign, and also the co-operation of the drilling contractor's employees. The geological map, mine plans, and forms accompanying the paper are from the Company's engineering office files.

Jan 1, 1937