Search Documents

By L Nagy, K P. Juhasz

The authors were engaged to optimise a traditional rebar cage reinforced concrete segmental lining by means of finite element analysis (FEA) using macro synthetic fibres for the Shanghai metro extension. The aim of this study was to reduce or entirely replace the original steel reinforcement of the segmental lining, in order to make the precast production process faster and more economic. The outer diameter of the tunnel was 6200 mm, the thickness of the segments was 350 mm.The numerical calculations were performed by Atena Finite Element software, which is based on the combination of Menétrey-William and Rankine failure surfaces on the compression and tension sides respectively. The effect of the macro synthetic fibres was modelled as tension stiffening on the tension surface.A one-to-one full scale model of an assembled tunnel ring using the original reinforcement cages was tested at Tongji University in Shanghai, July 2013. The ring was tested to differing load levels where load and displacement were measured until failure. The author’s first step was to calculate the real displacement characteristics of the original reinforced concrete (RC) ring, then calculate the numerically modelled version, so as to compare them. The material parameters of the concrete and rebar used had been determined through basic material tests conducted at the Tongji University. (Bi, Liu and Wang, in press).The numerical modelling undertaken has shown good correlation with the full-scale physical test results. Optimisation of the lining reinforcement was achieved through the addition of fibres, resulting in a substantial reduction of the steel rebar cages. Several results have been computed with the numerical model using different dosages of macro synthetic fibres, showing that the mass of steel reinforcement could be reduced by 50 and 75 per cent respectively.CITATION:Juhasz, K P, Nagy, L and Winterberg, R, 2014. Full-round numerical modelling of a macro synthetic fibre reinforced tunnel boring machine tunnel in the Shanghai Metro extension, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 477–484 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By M Thompson

"The Jaguar concentrator, 60 km north of Leonora, Western Australia (WA), consists of a standard closed circuit semi-autogenous grinding (SAG) and ball mill producing a float feed of approximately 60 micron at 70 t/h. Following comminution, separate copper and zinc concentrates are produced by differential flotation. These concentrates are subsequently dewatered by thickening and then filtration.Separate audits of the Jaguar Operation’s copper and zinc concentrate thickeners were conducted to evaluate their performance, following occasions where site personnel had identified unnecessary loss of copper and zinc concentrate to the thickener overflow. The feedwells were identified as the source of the observed problems due to the following issues with their design/duty:lack of retention time in the feedwell as current design is completely opennot conducive to effective mixing required for efficient flocculationdiameter of the zinc concentrate thickener feedwell was undersize for its duty.To improve the performance of the thickeners, it is planned to replace both concentrate thickener feedwells with a high rate design for their respective duties in February 2016. The audits also identified that the feed system requires modifications with particular importance placed on minimising air entrainment of slurry into the thickener feedwell. Minimisation of air entrainment is hoped to be achieved by providing constant head pressure through installation of weir arrangements in the feedboxes and redirecting each feed pipe so that it feeds tangentially into the feedwell. In addition, improvements to the control philosophy of both thickeners will be made with the installation of an ultrasonic bed level probe and bed mass sensor, in order to make real-time adjustments to the underflow pump speed to maintain steady state operation.Following the feedwell replacement and modifications to both thickeners it is expected that losses of recovered copper and zinc will decrease to undetectable levels. Subsequently it is anticipated that a more consistent, homogenous underflow can be produced for downstream filtration.Citation:Thompson, M, 2016. Concentrate Thickeners Feedwell Replacement, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 273–278 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By S Harvey

An inrush of water or mud into an underground mine, or sudden subsidence above mining voids represent low probability but high impact risks in underground mining. About two such incidents involving multiple fatalities or loss of production are reported each year worldwide. On average, Australia experiences one such incident every three to four years. This paper reports the development of a Standard that is intended to eliminate fatalities due to inrushes and subsidence.

Jan 1, 1998

By A S. Derrington

This paper describes a hybrid ventilation system, which uses secondary fans that also act as de-facto primary fans to extract fresh airflow from the mine intake raise system. Also discussed are the associated problems such as uncontrolled recirculation, inadequate decline airflow, fire safety issues, prolonged blast fume clearance times, high air temperatures in main access routes, neutralisation of mine air cooling by heat from secondary distribution fans, increased ventilation system complexity, reduced flexibility and high pressure differentials (which cause safety issues with personnel access and reduce secondary ventilation system performance).Practical suggestions are provided on options to avoid these problems listed.CITATION:Derrington, A S, 2013. A critique of the push-pull hybrid ventilation system, in Proceedings The Australian Mine Ventilation Conference , pp 73-78 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By J E. Powalisz

"The application of automated sampling techniques can help to provide a representative sample of process fluids and slurries that provide data for controlling process, custody transfer and quality assurance and quality control purposes.The automation of sampling provides a more consistent and reliable sampling process and eliminates many of the human-induced errors. Automated sampling can also provide a higher degree of safety in the plant/processing environment as well as better bottom-line results.Automated, fixed volume samplers can provide a very representative sample by integrating many small ‘grabs’ of sample from a process. Automated samplers can be controlled in a variety of ways to optimise the sampling process, including:cycle ratedwell timetotal volume.Properly selected and applied, an automated sampler can effectively isolate the operator from the process fluid during sampling and, to a great degree, during sample container collection.A variety of materials of construction, including seals, are available to handle demanding mining applications. Alloy 625, alloy 2205, AL6XN® and even certain plastics are used successfully in mining slurry applications.This paper explores the application of automated, fixed volume, batch style samplers in copper/nickel and gold processing, specifically pregnant leach solution and extraction fluids.Several specific field applications are discussed, including process installation details, hardware and operation.CITATION:Powalisz, J E, 2014. The application of automated samplers in copper/nickel processing, in Proceedings Sampling 2014, pp 35–42 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 29, 2014

By N Taylor, P Hewitt

The Northern Beaches Storage Project (NBSP) is part of Sydney Water’s SewerFix™ Program to improve the wastewater system and protect public health and the environment. It was built by the SewerFix Wet Weather Alliance (the Alliance), a partnership between Sydney Water, RPS, MWH, Parsons Brinckerhoff and United Group Infrastructure.The project temporarily stores excess wastewater diverted from the Narrabeen Submain during wet weather. The project considered a below-ground storage facility, which involved constructing a deep tunnel from Brookvale to Fairlight, connecting into the Northside Storage Tunnel and a storage tank, which was subsequently adopted and constructed.The storage tank scheme included a pumping station and inlet and outlet pipes installed by microtunnelling. The storage tank site is in the Brookvale industrial area situated in an area of deep marine sediments overlying Hawkesbury Sandstone at about 30?m below ground. Microtunnelling for the inlet pipe was conducted from a 12?m deep jacking shaft. The jacking shaft and 14?m deep pumping station excavations were carried out from within secant pile earth retaining structures adjacent to existing buildings.Construction activities had the potential to cause settlement of the adjacent buildings. During excavation and microtunnelling the water ingress, adjacent groundwater level and settlement of the adjacent buildings were monitored. The monitoring data was assessed against an action plan, which modified construction activities as required to minimise the risk of damage to buildings from settlements caused by lowering of the groundwater table outside the excavations. The secant pile construction, excavation, microtunnelling and pumping station construction proceeded without incident or damage to adjacent buildings.This paper highlights that tunnel/underground options should be considered during options development, describes the original storage tunnel scheme and presents details of the successful microtunnelling and deep shaft construction adopted on the NBSP.CITATION:Taylor, N and Hewitt, P, 2014. Tunnelling on Northern Beaches Storage Project, Sydney, to improve water quality, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 451–458 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By D P. Sainsbury, J Western, B L. Sainsbury, V Mutton, P E. Petrie

Remnant rib pillars at Castlemaine Goldfields Ltd’s Ballarat Gold Project have been sterilised by the placement of loose rock fill in production stopes. The application of selectively injecting low-viscosity grout into the backfilled stopes to form a stabilised material has enabled recovery of the previously sterilised pillars. This paper outlines the engineering design, quality control and quality assurance program implemented to ensure the safe and efficient recovery of the rib pillars. The successful program included laboratory testing, numerical exposure stability modelling and in situ monitoring.CITATION:Sainsbury, B L, Sainsbury, D P, Western, J, Petrie, P E and Mutton, V, 2014. Pillar recovery adjacent to stabilised rock fill at the Ballarat Gold Project, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 77–86 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By P Edmondson, S Narendranathan, S Setchell

The complexities of mining in current economic conditions, where ore extraction schedules are varied on a weekly basis so as to ensure constant supply to the process plant, can result in a number of scenarios that pose geotechnical challenges. This paper presents a case study where alterations in the mining schedule of a particular mine resulted in the necessity to mine under a large uncompacted embankment, ie integrated tailings and mine waste landform. To effectively ensure that ore recovery was maximised, a well-designed slope monitoring system to evaluate design performance and to provide timely warning of impending failures was imperative. In order for an appropriate slope monitoring strategy to be developed, a thorough understanding of the potential slope failure mechanisms, capabilities and limitations of available monitoring techniques is required. Communication of the monitoring results and response strategy to alarms generated by monitoring systems must also be carefully considered to maximise effectiveness. The results of preliminary stability modelling can be used to guide the design of a monitoring system, which in turn can then generate data which can be used to iteratively refine the geotechnical model. This paper illustrates the development and implementation of a slope monitoring system and associated communication system, using a case study developed at a large iron ore open pit mine in the Pilbara region of Western Australia.CITATION:Narendranathan, S, Lee, E C, Setchell, S and Edmondson, P, 2015. Modelling of an integrated waste storage facility, in Proceedings Tailings and Mine Waste Management for the 21st Century , pp 183–190 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 27, 2015

By J McCluskey, N Barros

"Long-term strategic planning at BHP Billiton’s Western Australia Iron Ore business aims for sustainable value maximisation of its large, long-life, low-cost, expandable mineral inventory and supply chain infrastructure. While mine plans are key components of this value equation, this objective requires a whole-of-business approach through comprehensive consideration and optimisation of the full value chain. Only through a system view do we believe that the value proposition of a set of plans is truly optimised.The fundamental considerations include: mineral inventory information, given its intrinsic uncertainty and risk/knowledge horizon a marketing view of future quality premium/discount based on overall market quality load whole of supply chain optimisation on a throughput accounting basis alternative sequences of capital decisions closure costs with significant magnitude of total movement requiring optimisation as part of the plan. In addition, the plan provides a view of acceptable uncertainty levels at different times in the future.BHP Billiton Iron Ore uses a structured Life of Asset planning process that supports the business with the optimisation of its maximum value proposition through a non-deterministic scenario-based optimisation approach on an annual basis. This is a key input to each year’s medium-term plans and budgets, including activities identified through a value of information approach that resolve the key uncertainties and steadily improve confidence in the plan.CITATION:McCluskey, J and Barros, N, 2014. Life of asset planning, uncertainty and value optimisation of the iron ore business – from exploration, to market, to closure, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014, pp 33–40 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 24, 2014

By C Woodall, G Jardine

The Henty Gold Mine, located in Western Tasmania uses innovative solutions to effectively manage a mining operation in an environmentally sensitive setting and has been presented with several environmental awards. Fill is required as part of the mining method to provide passive ground support, minimise rock exposure and ensure maximum recovery of the small but high-grade orebody. The use of the whole portion of leach residue in the backfill reduces the surface tailing disposal requirements. Therefore, High Density Paste Fill (HDPF) has been selected as the most appropriate fill method to meet these objectives. Additional benefits include the minimisation of excess water from fill and the subsequent need for the collection and treatment of water and slimes. There are minimal equipment requirements during placement, thereby optimising mine resources for production. This paper covers the development of a suitable paste fill system to meet the specific needs of the Henty Gold Mine and the successful commissioning of this system for the first time in Australia.

Jan 1, 1998

By M Salu

Ventilation control devices (VCD’s) and bulkheads are critical controls used for managing risk in underground coalmines. Following the Moura No. 2 mine explosion in 1994, the Queensland Mines Department required that the design of VCDs be based on live testing (such as in a mine testing explosion gallery) and more recently on numerical modelling using measured seal material properties. While the stipulated methods represent an idealistic solution, they are not practical to implement as solutions to daily challenges presented in underground coalmines.Not all VCD’s and bulkheads are placed in areas which have been mined to standard roadway dimensions. Operationally, VCD’s may be required to be placed close to intersections or require large dimensionally different areas (eg overcasts and pre-driven recovery road shutters) compared to the live testing or numerical modelling originally undertaken.This paper describes the various structural engineering methods utilised to account for the design of VCD’s where the operational requirements are non-standard. Siting and construction of VCD’s near the entry of cut throughs and geological structures requires additional design considerations. While VCDs constructed from a single material (eg sprayed mining plaster) are relatively straightforward to design, the addition of multiple openings (doors) or large pipes will complicate the structuralanalysis significantly.Temporary bulkheads used for the containment of grout such as for the construction of pre-driven recovery roads in coal mining have a significantly different risk profile to VCDs and should be designed accordingly. Recent failures and near-misses in such bulkheads have highlighted this issuefor the authors.The existence of an Australian Standard for Underground Mine VCDs and Bulkheads would go a long way to addressing many of the issues raised in this paper. Without a single, industry-accepted reference for VCD design, individual mines will have to continueto exercise their best judgements using whatever local expertise is available to them.

Oct 12, 2022

By J P. Burr

The Waterview Connection will complete a strategic Auckland motorway route linking the south, west and north. The project will include 2.1 km of ‘undrained’ driven tunnels, 500 m of drained cut-and-cover tunnel and tunnel portals.The project is aligned beneath a stream valley of Oakley Creek, which is incised through alluvium and in places overlain by landfill, between Mt Albert volcano and a ridge formed in alternating sandstones and siltstones. The resulting topography, geology and hydrogeology of the tunnel alignment are complex.The Assessment of Effects required estimation of the likely settlements resulting from the tunnel construction and assessment of their effects on the buildings, services and other features. A conservative approach was taken when estimating settlements in order to provide an upper bound estimate of the consequent effects. There are three sources of these settlements: mechanical settlement from the tunnel excavation, mechanical settlement from the displacement of retaining walls and consolidation settlement from the groundwater drawdowns during construction and, in some cases, in the long-term.The settlements from these sources were calculated independently and then combined to identify the most critical effects. These combined settlements were used to assess the potential damage to the buildings, services and other features above and around the tunnels. The combined settlement results generally followed the anticipated trough shape centred on the underlying tunnel but with some noticeable effects relating to the underlying geology and hydrogeology.The effects on buildings were typically assessed as negligible with some areas of very slight to moderate damage predicted. Effects on services are anticipated to be minor but some large and older pipes will require specific monitoring during construction. A monitoring programme is proposed to allow the actual settlement and effects to be compared to those estimated with appropriate responses should those effects significantly differ.This paper describes the methods used to calculate and combine the settlements and assess their effects.

Mar 8, 2011

By D Morrison, P Goodman

The cycle time between adjacent stopes is critical to achieving the required production rate from 3500 Orebody; one of the Enterprise Mine orebodies. Current Mt Isa cemented fills require a 90-day cure period which had to be cut to 30 days while maintaining the required strength criteria. The Enterprise Mine Feasibility Study recommended that this be achieved by Cemented Slurry Rock Fill (CSRF), but that on-going research into paste fill be continued. The continuation of the research, in conjunction with overseas visits has recommended that the 3500 Orebody be filled with paste fill, with the potential to fill other orebodies. The paste fill will comprise cyclone and thickener dewatered copper tailings to which Portland Cement (PC) is added before vertical borehole delivery and undergound pipeline reticulation to individual stopes. The benefit is not only re-use of copper tailings but also much reduced binder usage.

Jan 1, 1998

By W Mahoney, F Clement, E Saraiva

Prefabricated waterproofing sheet membranes are extremely complicated to install in underground sections with complex geometries and, despite being already subjected to quality tests in the factory, the installed membrane often exhibits leakages due to different reasons. Main sources of leaks are the required high amount of welding seams and damages caused during installation of reinforcement, as well as overstretching and poorly installed secondary concrete linings. Also the design of the tunnel lining is strongly influenced and limited by the use of prefabricated waterproofing sheet membranes. The use of sprayed waterproofing membranes for more than a decade has contributed to durability and serviceability, as well as to increasing sustainability of tunnel linings. The presented sprayed waterproofing membrane MasterSeal 345 is an advantageous alternative to prefabricated waterproofing sheet membranes under typical tunnelling conditions, especially in geometrically complex areas, such as in lay-by niches, cross passages and crossover caverns, where installation of conventional waterproofing membranes is inherently difficult, and locating leaks is challenging. This membrane has been successfully used in underground projects with different waterproofing design concepts and under diverse hydro-geological and environmental conditions for over a decade. It provides tunnel designers with different options and optimisation for the design of the tunnel concrete lining. Additional advantages to owners, contractors and designers from the use of the sprayed membrane include flexibility in the design, increased productivity and flexibility in working programming, as well as improved logistics, resulting in significant program and cost savings and reduced long-term maintenance costs. This paper describes the key features of this sprayed waterproofing membrane, its application range and limitations, the waterproofing concept, design options and related benefits. Further, guidance for membrane application and quality control and a summary of two recent project references in the United Kingdom and in Switzerland are provided.CITATION:Saraiva, E, Clement, F and Mahoney, W, 2014. The use of sprayable waterproofing membranes in underground structures – concept, design options, benefits and limitations, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 323–332 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By R Durchholz, A-J Heiertz, R Schmitz

Mining of lignite is the largest bulk materials handling activity in Europe. In order to mine this lignite, with an average calorific value of only a third of bituminous coal in an economical way, highly efficient opencast mining technology is mandatory. The total continuous mining of overburden and lignite was introduced more than 60 years ago and was subsequently developed stepwise into the largest mass transport system of the world. In 2011, the Inden Mine, one of three RWE Power mines, stripped 90 Mbcm of overburden to produce 22 Mt of lignite. In total, nearly 100 Mt of Lignite was produced from the three mines of RWE Power in Germany. Beside bucket wheel excavators (BWE), several high-performance in-pit crushing and conveying (IPCC) systems, which allow the adoption of continuous mining systems, even for typical shovel and truck (S&T) operations, are available today. RWE Power assists operators considering a change from the S&T to IPCC technology, both in the planning process involving large-scale belt conveyor systems and later with operational know how transfer. In a number of cases, the challenges associated with this system change have been addressed and solved successfully. One key challenge is managing the development of skills for operating the belt conveyor systems efficiently. This paper compares the effectiveness of S&T to different configurations of continuous mining operation for an up to 170 m deep mine with a total annual output of 117 Mbcm. From the mine operatorÆs point-of-view, the quantity and skill level of staffing required for operation and maintenance are discussed in detail. The main conclusion of this paper is the larger the operation becomes and the longer the mine life is, the earlier fully continuous mining systems should be planned and implemented.CITATION:Schmitz, R, Durchholz, R and Heiertz, A-J, 2012. Change challenges for large open pit mines, in Proceedings Eighth Open Pit OperatorsÆ Conference , pp 103-110 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 18, 2012

Copper-Cobalt hydrometallurgy has seen a resurgence in recent years with the development of projects in Zambia and the DRC. Many of the flow sheets are unique in their use of hydrometallurgical techniques to improve performance compared to the older types in current use. The emphasis has moved from direct copper electrowinning/stripping, with multiple stages of precipitation for removal of impurities and concentration of cobalt, to innovative use of solvent extraction and ion exchange with higher cobalt recoveries to final product. The poor quality direct electro-won copper has been supplanted with solvent extraction-electrowinning; with consequent production of LME 'A' quality metal. Many of the precipitation steps in cobalt recovery and concentration, have been replaced with solvent extraction; while the remaining precipitation stages have been enhanced with use of oxidants to improve impurity removal. Operating experience from two of these circuits has shown the benefits of the new technologies and the improved overall recovery of both copper and cobalt into higher quality products.

Jan 1, 2008

By J Tien, J Huang, N Haque, M O’Brien

Coal preparation is an integral part of producing coal for thermal powerplants and metallurgical processing plants. Coal processing plants use various unit processes to separate gangue and ash content from mineral coal, thus increasing the specific energy content.A flow sheet and a simulation model was established for a typical coal processing plant using Microsoft Excel. This model used the mass balance and split factors for run-of-mine (ROM) coal, tailings and water usage from a typical, generic coalmine.The common method of coal preparation initially involves several stages of crushing to reduce the size of coal. It is then sent to the processing plant for further washing. The typical method in Australia for coarse coal material processing is the use of dense medium cyclone (DMC) (Kininmonth and Baafi, 2009). Flotation cells are used for processing of fine coal. The fine products are utilised for coking coal only. In our case study, the intended coal product is for thermal powerplants. Therefore, the fine coal processing utilised spirals instead of flotation, which is typical for the industry.CITATION:Huang, J, Haque, N, O'Brien, M, O'Brien G and Tien, J, 2016. Development, simulation, economic and environmental evaluation of a coal processing flow sheet, in Proceedings Life-of-Mine 2016 Conference , pp 48–51 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By A Sturgess, P McKenna, P D. Erskine, D Doley, V C. Glenn

For more than four decades, rehabilitated lands in the Bowen Basin have been planted with buffel grass (Cenchrus Ciliaris), which is often used to provide rapid, stabilising and erosion reducing cover to reshaped landforms (Erskine and Fletcher, 2013; Harwood, Hacker and Mott, 1999; Grigg, Shelton and Mullen, 2000; Naidu et al, 1997). Historically introduced to Central Queensland and encouraged by pastoralists in the early 1900s (Humphreys, 1967), the species has been extensively used by mine managers in seeding mixes (Coaldrake and Russell, 1970; Edye, 1975), and the invasive nature of the grass has led to the monodominance in rehabilitated areas of semi-arid Central Queensland. With 40 open cut coalmines in Central Queensland (Department of Natural Resources and Mines, 2015), a considerable amount of land is either disturbed mine footprint (156 200 ha) or rehabilitated (29 200 ha) (Dale, 2015), and the bulk of rehabilitation consists of relatively young (<30-year-old) developing ecosystems, with demonstrated biomass fuel loads up to 20 t/ha (Grigg, Shelton and Mullen, 2000).Uncontrolled fire poses a significant risk to rehabilitated landforms that are located in close proximity to mining infrastructure, neighbouring communities, open pits with exposed flammable coal seams and flammable stockpiled coal resource. Mine lease holders in Queensland have the added responsibility of managing and protecting any endangered regional ecosystem communities, and flora and fauna listed federally under the Environment Protection Biodiversity and Conservation Act 1999 or the State Vegetation Management Act 1999; as well as, any culturally significant sites such as scar trees or middens that are found on-site. Additionally, uncontrolled fire in rehabilitated landscapes poses a significant risk to mine site closure goals, with the potential to create altered states and stalled ecological trajectories (Grant, 2006). CITATION:McKenna, P, Glenn, V, Erskine, P D, Doley, D and Sturgess, A, 2016. Fire behaviour in buffel grass dominated mine site rehabilitation in Central Queensland, Australia, in Proceedings Life-of-Mine 2016 Conference , pp 158–162 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By F Faraj, M Pal, M Haest, M Bradshaw, H Lang, K Hume

MineSense Technologies Ltd. is revolutionising grade control at mining operations by installing ShovelSense® sensors on buckets that measure the grade of every load before it is dumped in the truck. This allows the mine to exploit grade variations at a resolution that was not available before, reducing the amount of ore loss to the waste stream and removing waste from material destined for processing. These changes dramatically improve the profitability and sustainability of mining operations. ShovelSense relies on X-ray fluorescence analysis of the rocks as they flow in the bucket and is integrated with fleet management to direct the trucks to the right destination. Lab simulations of ShovelSense measurements on porphyry copper ores show correlations between predictions and lab measurements at 0.98 r-squared with a coefficient of variation of 10 per cent. Visualisation of copper grade predictions in three dimensions shows a reasonable match with the dig plan, but with local changes in the ore-waste contact due to more accurate contact identification, related to blast movement and other mining factors. Correct delineation of these contacts ensures ore trucks are not sent to the waste dump and waste trucks are diverted from the crusher, creating enormous value for the operation and the environment.

Mar 22, 2022

By R Burke, G Ramage, C Donnelly

Over the decades, Redpath has undertaken a multitude of tunnelling and underground excavation projects for civil and mining clients both domestically and internationally. These projects have been undertaken through varying strata conditions with differing excavation methods in remote locations and in central business districts.With the recent turbulent nature of the global financial environment, project drivers have been challenged with the emphasis being placed on methods to gain early access to orebodies, rapid development techniques, lower capital costs and reduced labour requirements to name a few.A number of mining companies seeking to achieve these objectives have commenced the journey to better understand the operational constraints, challenges and opportunities that may be available with the use of alternative excavation methods.The development of safe and effective alternative excavation methods that comply with both domestic and international mining legislation and regulatory requirements is a challenge the industry needs to embrace. Given the current cost pressures being faced by the Australian mining industry, some alternative excavation methods offer the potential for longer term sustainability and rapid development of resources.More recently work has been undertaken on a project that challenged the norm and implemented an alternative excavation method with the use of an excavator with a rotating drum cutter head.This paper will review this recent project and provide technical and operational insight into some of the challenges faced in implementing an alternative excavation method in the metalliferous industry.CITATION:Donnelly, C, Ramage, G and Burke, R, 2014. Challenging the norm – alternative excavation method in mining, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 187–190 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014