Search Documents

By F P. van der Meer, E Lessing, E Matthies

High pressure grinding rolls (HPGR) technology is growing to be a common comminution tool in iron ore processing. The technology finds a wide acceptance and presents specific benefits in coarse ore grinding and closed-circuit grinding in preparation of ball mill feed, right down to the other end of the particle size spectrum for iron ore pellet feed preparation.A growing number of minerals processing plants are facing higher operating costs and difficulties due to a scarcity of process water, which in some cases is a result of more stringent environmental constraints. In addition, many new iron ore deposits are located in more arid regions of the world. These challenges have led to operators taking a new look at dry processing of iron ores.The use of dry crushing and classification technology in cement production from blast furnace slag, clinker material or limestone feed stocks indicates that the technology may be applied in minerals processing. In addition, dry processing provides the possibility of generating a final product from finely disseminated and inter-grown ores at sizes near or well below 100 µm, as may be required for beneficiation techniques such as in fine magnetic separation, flotation or magnetic flocculation.Dry grinding by HPGR has a number of specific features, challenges and opportunities, including balancing power input, moisture content requirements and classification efficiency in the process design. HPGR parameters and the latest HPGR design and sizing capabilities indicate considerable potential benefits from this dry processing technology.This paper highlights some of the specific issues that play a role in dry HPGR application, with respect to energy and materials balances. Examples of dry HPGR practices and process studies in iron ore mineral processing are discussed.CITATION:van der Meer, F P, Lessing, E and Matthies, E, 2015. Iron ore final grinding by high pressure grinding rolls and air classification, in Proceedings Iron Ore 2015, pp 197–204 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By S R. Grano

The selection of the proper frother, specifically for a given ore, is essential in flotation. Traditionally, strong and stable froths are required in the scavengers, where metal recovery needs to be maximised, while selectivity must be achieved in the roughers and cleaners, where grade of concentrates is the main issue. The physical properties of a froth are determined both by frother type, by process water composition and by the amount and nature of the suspended particles. The evaluation of different frothers, in terms of metallurgical performance, is complicated at plant scale, since it may lead to periods of malfunctioning of the process and unacceptable decreases in recovery. On the other hand, evaluation based on frother chemistry only, is often unsatisfactory, because the frothing response is strongly ore dependent. A procedure, and proper tools, was developed at the Wark in order to perform the screening of candidate frothers at batch scale on real pulp samples. The main parameters related to froth stability (half-life time, froth height) are measured after introducing the pulp samples into a foaming column, where different conditions in terms of frother addition, agitation and aeration can be maintained. The approach has been applied to the selection of frothers for the flotation of an Australian sulfide ore. Procedure and results are discussed.

Jan 1, 2006

By B Murphy, N Strong, J Albrecht

Rio Tinto’s Argyle Diamond Mine has a history of underperformance with delivery of ore from the underground operation to the surface for processing with no real clarity in sources of loss and value. In order to increase underground production performance, the basic concepts of the Theory of Constraints model were applied to the Argyle underground production system. This prompted a revised view on bottlenecks and contributors to value loss and ultimately leading to record breaking mine performance. System loss reporting to demonstrate the best opportunity to drive value, departmental detail to develop tools to identify improvement opportunities and clarity across the team to ensure alignment and clear lines of communication were critical to the project success.

Mar 15, 2021

By M A. Noppé

"Investors and other stakeholders assessing the risk, opportunity and relative value associated with a resource project need to appreciate the project in its correct context. Errors, omissions, biased reporting or conflicting information in project reporting may lead to a misinterpretation of technical and financial results, resulting in biased estimates or assumptions on project value.This paper provides a simple ‘Resource Project Framework’ for presenting a project’s status that may be readily benchmarked against other similar projects and to illustrate the stages required to advance the project outcomes to higher levels of certainty. The framework draws on definitions and guidelines readily available in various resource industry reporting codes and public company reporting requirements.The framework assesses three key areas for placing a resource project in its correct relative context, namely:the project development stagethe confidence in the Exploration Results, Mineral Resources and/or Ore Reservesthe level of accuracy, precision and confidence in the technical and economic studies supporting the reported results or options for the project.The application of the Resource Project Framework is illustrated using two project examples, one from publicly reported company project releases and the other for two development projects.CITATION:Noppé, M A, 2016. A framework for presenting and benchmarking resource projects, in Proceedings Project Evaluation 2016, pp 260–274 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 8, 2016

By M Rauer

With a worldwide growing population the demand for higher living standards, food and the development of new technology is rapidly rising. To allow for a continuous growth, larger quantities of minerals and raw materials are needed at a faster pace. Different methods have been developed to access or tap ore more quickly, such as improved drill and blast operations, mechanical mining methods using equipment such as roadheaders (RH), longwall miners and other technical equipment. Another possibility to access and develop mines faster is the use of a tunnel boring machine (TBM).The historical usage of TBMs is surprisingly long, but the opportunity for technology adoption by the majority of worldwide mining companies remains largely untapped. Dozens of full face TBMs have been used by mines around the world, including two that will begin operation soon in Australia. TBMs have been used to safely and rapidly gain access to the orebody, or to expand access to the orebody to increase output by running a TBM along the edge of the orebody for several kilometres. These machines have also been used for ventilation and for conveyor tunnels for ore removal. They have been used to quickly excavate long and winding declines giving access to an orebody at several levels in a short period of time.Tunnel boring technology can be used for mine declines, mine access tunnels and all sorts of different mine designs and set-ups. TBM technology simply needs to be adapted to the mine conditions and, if manufacturers are involved early on in the planning process for mine development, the operation can be very successful. In some cases, historically typical mine designs may need to be re-thought.One mine, the Stillwater Platinum mine in Nye, Montana, is currently employing its fourth TBM in 25 years. Two were used to create tunnels running alongside the orebody, rapidly expanding access to the orebody in many locations for increased output. Two were used to create parallel access tunnels to a mine expansion at the East Boulder orebody; one tunnel is for conveyor haulage and the other for vehicular access. TBMs have been employed successfully many times to rapidly drive vehicular decline tunnels to multiple mine levels, such as at the San Manuel – Magma Copper mine in the USA. While TBM technology may not seem to be optimal for every mine, these success stories show that the method can provide vast benefits for the right projects.Early use of TBMs in extremely hard rock metal mines, in the 1960s and 1970s, had limited success since performance was low. However there have been great improvements made over the years in the strength of rock which can be excavated by TBMs with high performance. Other important improvements involve the provision of a safe work environment, safely and rapidly supporting the rock and predicting geology ahead of the TBM.This paper will briefly note the more than 20 TBM mining projects and highlight some notable successes. It will then go on to give a status report on the two active TBM mining projects in Australia and the difference between a TBM operation versus other excavation methods such as drill and blast (D&B) or RH excavation.CITATION:Rauer, M, 2014. Tunnel boring machines in mines – a?brief review of past use with a status report on use today in Australia, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 663–670 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By C Jones

When the Paulsens operation was poised to be placed on care and maintenance, Bill Beament and the rest of the Northern Star Resources (NSR) team capitalised on the opportunity to send the Ashburton region’s only operating gold mine into the record books.A three-stage strategy was devised by NSR to pay off the acquisition and maximise the return from the operation. The first stage was to mine the 55 000 oz mine plan and pay off the cost of the acquisition, then maintain profitable production beyond the seven months and re-establish a mine life. The second stage involved an early commitment to a 220 m long diamond drill drive being placed in the hanging wall of the orebody from which the extensions of the orebody could be further explored, allowing the second stage of the plan to come into effect and extend the mine life by converting Inferred Resources into the mine plan. The third stage of the initial plan was to utilise this drill drive and continue to drill deeper holes beyond the current limit of drilling in the ore zones to extend the orebody and increase the mine’s life.With an ever growing desire to further expand, the young company took on the bold move of establishing its own mining services division. A critical element to the success of this was ensuring that the right people were recruited with the appropriate specialised skill sets.Aligning common goals amongst all NSR team members, from the board and senior management to the work force on site, was critical to integrate the new and driven direction that Paulsens had adopted. It was essential to change the focus and a shift in all employees’ attitudes and values from a mine that was all but down and out, to a site that wanted to be kicking some serious goals.Teaming together a passionate and driven leader with a strong allied workforce was always going to put NSR in the best position possible to make Paulsens the success story that it now is. But without the calculated risks and enthusiastic attitude, the little known mine site in the Pilbara might have remained just that.CITATION:Jones, C, 2014. The Paulsens transformation – a shining light under a northern star, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 191–196 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By S Ravn

Under platform exhaust (UPE) systems are often designed into metro stations as a means of removing heat generated by trains as they come to a halt in the platform. These systems are designed to extract heat from the brakes and brake resistors directly at the source in order to capture as much heat as possible before it can enter the public areas of the station, or contribute to the temperature build-up in the tunnels. Due to space requirements for the associated duct and air handling units, the UPE plays a significant role in the geometric design of the platform and station as a whole.In recent years questions have arisen as to the effectiveness of UPE systems. However, very little data is available for designers to use when making important decisions on the station designs for new metro systems. This is important as significant savings could be achieved by omitting or re-designing these systems for new build stations; not only due to the capital costs of space provision for the duct itself but also due to the associated operation and maintenance cost of the UPE system.This paper will present recent measurements of the UPE system of the Copenhagen metro together with one-dimensional (1D) simulations, looking at typical dispersion of heat into the station plenum box and air exchange through draught relief shafts as the train enters the station in order to evaluate the effectiveness of the UPE system. The aim of this paper is to disseminate the results of measurements and analysis to increase awareness of the issue and to provide discussion relevant to designers in their evaluation of heat removal systems in new build station designs.

Mar 8, 2011

By M Brockman, M Cowan, A Robeson

"Sunrise Dam Gold Mine (SDGM) is located 820 km from Perth, 220 km from Kalgoorlie—Boulder and 55 km south of Laverton in Western Australia. The SDGM main pit had successfully operated since 1997 and was due to be completed during 2012. An opportunity existed to extract the high-grade crown pillar – 600 kt @ 7 g/t for 135 koz by either open pit or underground methods.The crown pillar was the 60 m (vertically) thick remaining part of the high-grade Cosmo orebody between the top of the paste filled underground mine stopes and the planned base of the final open pit shell.There were two major difficulties being considered when choosing the underground or open pit options:a major wall failure in the upper section of the main pit wall directly above the crown pillar restricting access from the base of the open pit to the top of the crown pillarimpact of a high rainfall event while the crown pillar was being mined from either surface or underground resulting in flooding of the underground mine workings.This paper will discuss the following issues:the process to identify and evaluate the risks in both options using knowledge based modelling software; this technique allowed the evaluation of a complex set of assumptions to arrive at the preferred optionremediation of the Watu failurethe selection of the preferred option and the challenges encountered before, during and after the extraction of the crown pillarthe planning and geotechnical work to ensure the safe extraction of the crown pillarsuccessful outcomes transitioning from open pit operation to a solely underground operation.Citation:Robeson, A, Cowan, M and Brockman, M, 2016. A Case Study on the Assessment, Planning and Extraction of the Crown Pillar at Sunrise Dam Gold Mine, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 115–136 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

By B Shi, Y Li, L Ma, F Zhou

Subsurface fires are a common threat to coal mining, as spontaneous combustion of coal can potentially result in gas combustion and explosion. Fire-proof techniques, such as grouting, foam, or colloid injection, are not in a position to function ideally, due to the limited coverage and stopping the extinguishment substance from reaching the fire location. Liquid nitrogen, as a kind of all-submerged fire prevention or extinguishing method, can rapidly extinguish fires, thus preventing gas explosion and minimising extinguishment time. Injecting liquid nitrogen through boreholes is an important way during the period of mine catastrophe. But liquid nitrogen is not effective enough in infusion; technical issues restrict the development and utilisation of liquid nitrogen fire prevention and extinguishing technology. Immediate infusion of liquid nitrogen is usually associated with ‘air slug’ (the balloons and bubbles in the pipeline which hinder the flow of low-temperature liquid), which blocks pipelines for liquid nitrogen injecting. Another issue is that the pipeline tends to be damaged due to freezing, which undermines the injecting efficiency of liquid nitrogen and its application result. In order to solve the problems of the low efficiency and some other related field issues in liquid nitrogen perfusion, the ground–underground high efficiency liquid nitrogen injection technology were developed. Implementation of liquid nitrogen infusion techniques in Chinese coalmines achieved the goals of fire prevention and air-cooling. The technique presented in this paper is efficient in absorbing heat, and consequently, displacing oxygen and combustible gases. Field tests at Rujigou and Yangchangwan Coalmine justified the efficiency of the technique. By using this technique, there was no waste left behind, which may impede the subsequent production. The presented technique is of great benefit to the social, economic, and environmental aspects of mining operations, and will have broad applications in fire prevention for large-scale coalmines.CITATION:Zhou, F, Shi, B, Li, Y and Ma, L, 2015. Key techniques and engineering applications of stereoscopic liquid nitrogen infusion for coalmine fire prevention, in Proceedings The Australian Mine Ventilation Conference, pp 291–298 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By J Rock, K Bambrook

"Hanwha Mining Services was approached by Glencore Coal to provide a series of (trial) demonstration blasts at its Clermont coalmine. The intent of the project was to trial a bulk explosive product that would be able to provide sufficient energy for the ground type encountered without production of post-blast fume. Three blasts were loaded using the patented XLOAD bulk explosives with a density of 1.00 g/cc. XLOAD bulk products are water resistant explosives that can be loaded at densities much lower than traditional (generic) water resistant heavy ammonium nitrate – fuel oil (ANFO) or pumped blends with significantly reduced risk of fume. In addition, these products have detonation characteristics that generally deliver a higher heave partition than conventional bulk products and hence improve muck pile looseness and digability.The priority key performance measures included the absence of fume from blasting, being at least cost neutral and providing similar if not improved shovel dig rates. The design for the initial blast took a conservative approach to ensure the key blast outcomes of fume control and fragmentation were achieved.The second blast used the same pattern dimensions as the benchmark bulk product used in this area to provide a cost neutral comparison with the benchmark products that had been used over the prior six months. This resulted in a 20 per cent lower powder factor than would have otherwise been used. To test the suitability of XLOAD, this shot was slept for over two weeks between loading and firing in geology where the sleep time is typically kept to a few days to minimise the fume risk.The third blast utilised a slightly larger drill pattern to push the capabilities of XLOAD and provide a cost neutral comparison between the trial product and the traditional benchmark products. All three blasts were fired with no fume observed, no recordable incidents and good fragmentation. Shovel productivity from all three of the trial blasts was excellent with higher average instantaneous dig rates being recorded (average six per cent improvement against the instantaneous dig rates recorded for the benchmark blasts).Citation:Rock, J and Bambrook, K, 2016. Controlling Blast Related Fumes with Unconventional Explosives, in Proceedings Ninth AusIMM Open Pit Operators' Conference 2016, pp 39–49 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Nov 15, 2016

The Savage River open cut magnetite mine is located in rugged terrain in densely rain forested northwest Tasmania. The mine and concentrating plant are both in the Savage River valley. Pickand Mather Incorporated (PMI) operated Savage River as an open cut magnetite mine between 1966 and 1996. Acid rock drainage (ARD) was first noted in the last ten years of the operation, leading to elevated concentrations of heavy metals downstream of the mine. When operations ceased in 1996, PMI returned the mine to the Tasmanian Government along with a remediation fund of $11.4 million. At that time, the assessed cost of remediation was in excess of $120 million. As a result of the ongoing ARD contamination and to facilitate both a new operation and effective remediation, Goldamere Pty Ltd negotiated an agreement with the Tasmanian Government in 1996, which resulted in the Goldamere Act and the Goldamere Agreement. The agreement has allowed Australian Bulk Minerals (ABM) to remediate the Savage River mine in conjunction with the Tasmanian Government while re-invigorating a previously closed mine by providing ABM with an indemnity against past pollution. ABM can configure its mine and waste planning activities to maximise remediation benefits without fear of future litigation for past mistakes. The effect to date has been the development of a long-term strategy to remediate the Savage River and short-term remediation works such as water management, which provide benefits to the ecosystem. After five years, the Savage River is no longer significantly impacted by ARD for 30 kilometres downstream and trout are now reported within the reaches of the mining lease. The arrangements between ABM and the Tasmanian Government are an example of a genuine WIN WIN situation where co-operative environmental management of the site results in significant improvements and where the æregulatorÆ and the æminerÆ are working together to achieve mutually beneficial goals. The end result is a significant benefit to Tasmania.

Jan 1, 2003

During 2009 the technical services staff at Barrick Gold Corporation's Australian Business Unit conducted a review of their five underground mines that utilise pastefill as the backfill component for these operations. Of the five mines reviewed three use dry tailings and two use wet tailings plants. The primary aim for these reviews was to determine whether pastefill was the right option to be used, and if not, what where the alternatives. The reviews undertaken focus on several areas including, paste plant operation, reticulation and barricade techniques, the geotechnical requirements for pastefill in regards to the current mining methods, the consideration of alternative methods, capital and operating cost histories compared to initial estimates, and a cost benefit analysis of pastefill against other mining methods. The main benefits from the use of pastefill is increasing the extraction of the resource, reducing or eliminating the need to leave pillars. In some mines the use of pastefill is geotechnically driven, to manage high stress environments or mining induced seismicity. A third benefit of using pastefill in some circumstances is that it reduces dilution, however it is considered that this is not a valid argument for most of the mines reviewed. At two mines no alternative to pastefill was determined, whilst differing extraction and filling strategies were potentially identified at the other three mines. The reviews developed cost benefit curves for those sites that had alternative mining methods to assist in determining whether pastefill is the right option to use for any particular stope. At the grades typically mined in each operation, pastefill was the preferred option to use. In all mines, pastefill was determined to be the best option at this time.

Nov 25, 2010

By J N. Farrell

Metallurgists frequently use a small number of large samples to characterise expected mill performance, with the a priori assumption that these few samples are representative of the entire deposit. Geometallurgical sampling is becoming more prevalent as a way to use many smaller samples to indicate the expected recovery as part of the Mineral Resource or Ore Reserve estimation.The evaluation of magnetite deposits involves specialised approaches to sample preparation, sample analysis and resource estimation. The sampling protocol for magnetite deposits will typically include the use of Davis Tube analysis. The Davis Tube is a mini-pilot plant that is used for determining the mass magnetic recovery from a small amount of sample ground to a specific size. The magnetic concentrate may then be analysed and together with the mass magnetic recovery, may be used to simulate the expected mill recovery. The magnetite sampling protocol is specific to each deposit, and is typically designed around a specific metallurgical flow sheet.During resource modelling, the mass magnetic recoveries and concentrate grades may be estimated directly or assigned to a block model using regressions with other chemical constituents. For estimation, the concentrate grades are weighted to account for the different mass magnetic recoveries of each sample and the impact of these differences on the concentrate estimates.

Sep 5, 2011

In recent years there have been many changes in mine ownership due to the on-going rationalisation towards larger mining companies. Larger companies inevitably find it hard to manage small mining operations and in many cases smaller mines do not fit corporate resource, production and profit criteria. Smaller companies are more suited to managing these medium or small scale mines and are tendering for the purchase or lease of mines that larger companies wish to dispose of. In addition to these factors there has also been a trend (especially in Western Australia) for mines to continue operating at ever increasing depths. This in turn has led to more mines operating in high stress environments and experiencing damaging seismicity. Assessing the viability of seismically active mines from a takeover or purchase point of view should involve analysing the risk profile of every aspect on mining that could be affected by adverse seismicity. This includes assessing current and alternative mining methods, mine designs, support systems, extraction sequencing, monitoring and blasting. This paper includes discussion on items that need to be assessed when considering the purchase of seismically active mines, with experience gained from some recent studies in Western Australia. In these cases it was apparent that quantification of previous seismic history on itÆs own was a totally inadequate method of assessing minewide seismic risk potential. A more holistic approach is required, taking into account all aspects of relevant data, all the minewide effects of seismic activity and all possible means of mitigating those effects.

Jan 1, 2002

By J A. Rowland

When executing a ventilation change the mine ventilation circuit is in a state of flux throughout the entire change period with discrete mine areas both under ventilated and/or over ventilated during the change process. Whilst routine risk reduction strategies such as removing electrical power and people from the mine are commonly deployed it is wise to complete the change in the shortest practical time frame. This not only minimises the chance of unacceptable concentrations of contaminants accumulating around the mine but reduces the impedance on production activities which are routinely suspended during these change periods. This paper firstly highlights the importance of the maintenance of an accurate ventilation model and discusses issues which should be considered to assist to maintain in it a suitable state of health. Further it provides some tips on how to monitor that your model is in an acceptable state of tune so that it can be confidently deployed in the change process. Finally, it details the sequential process how a finely tuned and accurate ventilation model can be utilised to carry out major ventilation changes according to appliance pressure adjustments only and without the need to constantly measure and check resultant branch flows throughout the whole change process. Also discussed are some simple practical tips which will help ensure that the ventilation change process will go according to the devised plan on the day and in the most appropriate order including checking the efficiency and accuracy of the change, after it is completed.

Oct 12, 2022

By X Li, J Wang, D Liu, Y Liu, K Hu

"Since the adoption of open-door policy 30 years ago, rapid economic growth has resulted in serious resource depletion and environmental destruction, especially in mining areas. As an urgent response to this situation, the central government and the Ministry of Land and Resources (MLR) have adjusted policies with concrete and realistic actions for halting this trend of non-sustainable mining activities in China. æGreen Mine CampaignÆ is one of the actions implemented. In 2010, MLR announced the æGreen Mine CampaignÆ, in which existing and new mines will be evaluated against the æGreen Mine Construction StandardsÆ and certified as æGreen MineÆ if complying with these standards. The standards cover five key aspects: the considerations of science-supported resource exploitation efficient resource utilisation standardised management environmental friendliness harmonious community relationship.Every year, MLR reviews ægreen minesÆ from all provinces. Thirty seven mines, including coal, metal, non-metal, gold, chemical industry and building materials mines, passed the review and were certified as green mines in 2010. In 2011, 187 out of 194 mines that participated in the review were certified as ægreen minesÆ. These mines are viewed as good examples of sustainable mining development in China.CITATION:Liu, Y, Hu, K, Li, X, Liu, Y, Liu, D and Wang, J, 2012. The green mine campaign and sustainable mining in China, in Proceedings Life-of-Mine 2012, pp 339-342 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 10, 2012

Western Deep Levels, a seismically active deep level gold mine, started placing backfill in their narrow tabular workings as part of the regional support strategy in 1986. Over the years the percentage of working places being backfilled has been gradually increasing. At the end of 1995 the support efficiency and the labour productiveness relating to support installation were scrutinised to determine if resources were being optimised. Owing to financial, safety and productivity constraints it was decided to redesign stope support to be less labour intensive, safer and provide an integrated stope support system. This new integrated system will thus combine the previously used temporary, permanent and back area support consisting of mechanical props, hydraulic props and backfill respectively. Backfill previously formed an integral part of the regional support in conjunction with strike stabilising pillars. To design the integrated support system the backfill placement quality has to be exceptionally good and placement must be done as close as possible to the working face. The backfill to face distance was reduced by 30 per cent and in some areas by more than 50 per cent with an increase of square metres filled to increase the effect of the backfill even more. This paper addresses the design and successful implementation of an integrated stope support system based on the optimisation of backfill to the extent where installation of mechanical and hydraulic jacks could be eliminated.

Jan 1, 1998

By M J. Schultz, R L. Rude, D M. Tomko

The US Mine Safety and Health Administration (MSHA) conducted compliance assistance diesel particulate matter (DPM) sampling throughout the underground metal and non-metal mining industry. Based on that sampling, MSHA identified mines that were having difficulty meeting the DPM limit. To provide further assistance, MSHA then visited approximately 60 of the mines that were experiencing difficulty complying with the DPM standard. As part of these visits, DPM exposures were measured and control technologies for DPM were observed and assessed. Controls consisted of ventilation, clean engines, environmental cabs, alternative fuels, diesel particulate filters (DPF) and work practices. The focus of the follow-up compliance assistance visits was to assess control effectiveness and to make recommendations to mines experiencing difficulty in meeting the DPM standard. At each mine visited, the ventilation controls were evaluated, engine emissions were determined for equipment in use, environmental cabs were examined, and operational practices were noted. Additionally, control technologies, including alternative fuels and DPF were evaluated in several mines. A comparison was made of mine and section airflow to equipment particulate indices. Based on engine emissions, horsepower and operating time, the contribution of individual engine emissions to total emissions was made. Environmental cab integrity, positive pressure and air filtration systems were checked and operational practices relating to DPM exposure were assessed. This paper summarises the preference and magnitudes of controls that were typically used or needed for successful control of DPM. Additionally, results of the assessments of alternative fuels (including bio-diesel and water emulsion fuels) and DPF are presented.

Jan 1, 2005

By A Turichshev

The synthetic rock mass (SRM) approach for modelling jointed and veined rock has been at the forefront of caving geomechanics research for years. A well-constructed and calibrated SRM model can capture the full rock behaviour at a macroscopic scale. Traditionally, SRM technology employed bonded particle models (BPM) due to their ability to model rock’s response to loading without prior specification of behaviour. The SRM modelling process requires the BPM to simulate intact rock and the subsequent introduction of fractures or veins by changing bonding characteristics between the particles. However, bonded particle materials have difficulty reproducing both the compressive and tensile strengths of intact rock. This and other limitations of BPM have been the driving force in exploring the potential of grain-based (2D) and bonded block (3D) models (BBM).This paper reports on recent work exploring the applicability of both BPMs and BBMs in 3D to the modelling of intact rock. The advantages and limitations of both BPMs and BBMs are addressed based on the results of numerical simulations using the PFC3D and 3DEC distinct element codes. The preliminary results suggest that BBMs are better suited for simulating intact rock behaviour than BPMs. Ongoing work aims to better qualify the applicability of BBMs under different conditions. This has significant implications for our understanding of rock mass behaviour in a caving environment.CITATION:Turichshev, A and Hadjigeorgiou, J, 2016. Simulating intact rock behaviour using bonded particle and bonded block models, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 453–460 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By M Wortley, J McKay, D La Rosa, O Guyo

It has been a generally held concept that crushing operations were, by their nature, too simple to benefit from the implementation of advanced process control. The commissioning of an OCS¬ expert control system and image-based oversize detection system, VisioRock, at the Pilbara Iron Tom Price facility are dispelling these notions. A constraint-based OCS¬ expert control system has been designed and commissioned on the high-grade crushing and screening plant along with a vision-based oversize detection system functioning on six product conveyor belts. To date, the expert control has demonstrated the ability to increase production by maximising dynamic constraint utilisation. Dynamic constraint utilisation is a concept developed by Rio Tinto Technical Services for effectively evaluating constraint-based control logic performance. The VisioRock system has been installed and configured and has been operating for a period of several months. Currently, Tom Price and Metso personnel are working to define correct oversize detection thresholds. Details of the plant implementation are discussed.

Jan 1, 2006