Search Documents

By S Tavelli

This discussion will present a case study in developing solutions to a metropolitan quarryÆs public relations, legal, environmental, and productivity problems. It details an extensive and detailed project to address the blasting practice in a medium sized quarry that is surrounded by residential and industrial zones. The principle work was done over four months duration during the normal production season. It included detailed drilling and blasting audits for baseline information. In addition, geologic characterisation, seismic modeling, correction of deviations from best practices, and implementation and monitoring of precise electronic timing to provide dramatic solutions for the quarry. The quarry is in the near suburbs of a large metropolitan city. It is framed on two sides by residential municipalities and on two sides by industrial zones. At the start of the project, the quarry was in court as a result of the lawsuit by one of the neighboring towns that was suing to close the quarry. The lawsuit had progressed to the advanced stage where in the Judge had appointed an arbitrator to make the decision of continued operation. This arbitrator was to observe our progress and recommend to the Judge the disposition of the case.

Jan 1, 2004

The increasing introduction of high capacity mechanical equipment into the coal mines of New South Wales following. tforld War II brought with it problems of roof support. Rapidly advancing headings in difficult country could not be supported with heavy, close,timbering due to the time involved in installation and the reduction of available' space for the movement of machines. _ The installation of low cost, space saving, rapidly installed roof supports became a necessity if the new mechanical equipment wa-s to be allowed to operate at maximum efficiency. As, a result of experience in the United States of America, the system of roof support using steel reinforcing bolts began to find increasing, popularity in the mechanised mines in this State. From the somewhat'crude methods of in- stallation adopted in some of the, early trials, the practice of roof bolting has advanced into a-highly technical operation, requiring care and skill to ensure optimum results.

Jan 1, 1971

At Renison Limited, on the West Coast of Tasmania, modern trackless decline mining is practised to exploit the various tin bearing sulphide deposits. With footwall accesses, one of three adaptations of horizontal mechanised cut and fill, 1. unsupported, 2. pillar supported,and 3. unsupported - resuing is used to stope each defined ore block. The stoping method is basically determined by the dip and true thickness of the ore with emphasis on high ore recovery. Extreme flexibility is possible by the selective mining of stope lifts, the consumption of development waste as fill and the utilisation of the same mobile equipment in all phases of production. This has resulted in high productivity and low cost per tonne of ore.

Jan 1, 1977

By J E. Eberhardt

Ore sorting has long been used to raise the efficiency and thus lower the environmental impact of mineral processing operations. It was first instituted as hand sorting, according to a humanly perceived difference in the ore, but is now automated using large mechanical sorters in order to meet the high tonnage throughput required in most minerals processing applications. In the past, ore sorting was generally used as a niche processing route when other approaches failed, and in this context, consequential environmental benefits are often not the first consideration in adopting sorting. When applicable, ore sorting offers environmental benefits in reductions in fines waste, reagent usage and energy consumption in milling. Although there are significant opportunities for the use of ore sorting technology in many minerals processing operations, industry applications, to date, have been limited mainly to the processing of diamonds, magnesite, talc and uranium ores. This limitation has principally been due to a lack of suitable sensing technologies for a wide range of ore types. The authors report on a wide-ranging review of the automated sorting of mineral ores, and in particular, on methods for discrimination of ore characteristics prior to mechanical sorting.

Jan 1, 2002

By D Beck, E Jones

The measurement and management of deformation in underground excavations is a key responsibility of geotechnical and mining engineers. A critical aspect of these roles is to ensure there is sufficient ground support capacity for the expected demand.Current methodologies for monitoring deformation and ground support serviceability-limits require measuring displacement at distinct points, or using visual observations. These current methods limit the assessment to a qualitative interpretation of deformation across the entire excavation.Recent advancements of Light Detection and Ranging (LiDar) technology permit a new method for monitoring deformation that allow a full 3D image of extended sections of an excavation to be precisely scanned. The results from the comparison with subsequent scans provide valuable information on the magnitude, direction and extent of regions exceeding the ground support serviceability-limits. This new method now provides a quantitative assessment across the entire excavation being monitored.The implementation of regular scanning has been demonstrated to be highly advantageous not only at mines with swelling or squeezing ground, but also at mines with rapid seismic induced deformation. The use of LiDar technology as a routine deformation measurement tool for geotechnical and mining engineers (and further applications) are discussed in more detail in this paper.CITATION:Jones, E and Beck, D, 2017. The use of 3D laser scanning for deformation monitoring in underground mines, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 267–270 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By J M. Menacho, L Zhang, A Hoadley, L Verdugo, B Etschmann, W Bruckard

Since the introduction of Lithium-Ion Batteries (LIBs) in 1991, the market for lithium-ion cells has been driven by the high demand for portable electronic devices and more recently for batteries for the electric car industry. It is expected to grow rapidly to reach 2600 GWh globally by 2030 (US Government, Office of Energy Efficiency and Renewable Energy, 2021). However, there is a desperate need to recycle LIBs to recover valuable cathode materials and graphite. For this reason, several physical and chemical recycling technologies have been proposed to recover these materials from spent batteries. Amongst these, froth flotation technology is a potential cost-effective technology for separation of the graphite fraction from the lithium oxide components due to the natural hydrophobicity of graphite and density difference between graphite and cathode materials (Folayan et al, 2021).

Aug 24, 2022

In the sixteenth century the Spanish Captain da Alvaro Soavedaro, on a search for the explorer Ferdinand Magellan, came across the main island of New Guinea which he named Isla del Oro (Island of Gold). Since that time exploration for, and mining of, gold has been pursued by many, culminating in . the development of major world-class projects in the latter part of the 20th century. Though various prospectors have panned for gold and small gold mining projects were undertaken through the seventeenth and eighteenth centuries, it was not until the 1880's when mining became a more concerted economic venture. Misima and Woodlark Islands in Milne Bay, Gura-Ackera and Yoada in Oro, and Lakekamu in Gulf Province and Keveri in Central Province were all gold producers by late nineteenth century. It was in the 1920's that corporations began mining in PNG and with the commencement of production at Panguna in Bougainville in 1972 a new era of mega-project mining began.' Today there are two large mining projects producing mainly gold and copper. The first, already mentioned, is Panguna on Bougainville Island. This project has provided Government with $US 475 million in taxes. ok Tedi is the second large mine development located in Western Province. It began production in 1984 with the extraction of the deposit's "gold Cap".

Jan 1, 1987

By J Champa

The mining industry internationally seems on the verge of a major underground support revolution as suppliers, mines, consultants and researchers develop, test and use thin support (structural) membranes (or superskins as they are commonly called) mainly as a replacement for screen/wire mesh. Thick membrane support in the form of shotcrete (sprayed concrete) has been used since the 1950s in underground mines. Shotcrete, in mines, is generally applied at a thickness between 25 and 100 mm depending on the need. Thin membranes are however applied at a typical thickness between 2 and 6 mm. Certain thin membranes have been available for several years (Tannant et al, 1999), but the intense interest in such supports has only grown in the last few years. The interest lies mainly in the potential to safely reduce the mining cycle time and hence improve productivity. There is however considerable confusion concerning such supports, and this paper attempts to clarify certain aspects and dispel certain misconceptions and myths about thin support membranes.

Jan 1, 2000

By Gottlieb P, Sutherland DN

The paper describes a method of making quantitative mineralogical measurements on many of the major lead/zinc orebodies in Australia. The work was done using QEM*SEM. It was found that a relationship betwen phase-specific surface area and particle size, when plotted in a suitable way, gave a straight line with slope related to the grain size of the mineral in question. The method provides an excellent way of differen- tiating between minerals in existing orebodies and, consequently, an easy way to establish a comparison between a new prospect or orezone and current operations.

Jan 1, 1988

This paper discusses considerations to be made for the selection of rock tunnelling machines, as opposed to drilling and blasting. A systematic approach is presented in terms of utilizing data frcm site investigations to accurately forecast machine performance for estimating and planning purposes and to help minimise associated risks. Useful rock index properties are identified, and correlations for predicting advance rates for roadheader and full face machines are presented together with a simple method of characteristing rock mass conditions for estimating machine utilization and the savings to be gained in support costs. Finally considerations for tunnelling in adverse ground, for advance probing and for large sized tunnels are outlined.

Jan 1, 1987

By A Weeks an, R Bertinshaw, S Khosrowshahi

Good mining is central to any approach to value tracking. Good mining occurs where the ore is correctly delineated, measured and fed to the mill. This process is usually referred to as grade control, ore control or quality control. There are now ways to measure the efficiency of this process, such as by using conditional simulation, and a brief synopsis is presented. Resource estimation is the foundation of ore reserve estimation, which should enable useful prediction of the expected metal to be recovered from mining and milling. Significant improvements have resulted from applying new techniques such as the Chain of Mining (CoM) method, which models the mining process. Again, a brief synopsis is presented. Tracking value from the mine through the mill implies a linear sequence of processes that can be modelled. Reality is more complex and there are error components, feedback loops and breaks in the Chain of Value. Modelling the total production process in a number of operations is considered, including the various impacts on producing reconciliations. Procedures are also discussed for handling a number of difficult issues such as: different data supports, stockpiling strategies, blending from multiple ore sources, blast movement and underground ore extraction.

Jan 1, 2002

By Todd W, Stone C

A 3D graphics modelling system has been applied to longhole stope ring design at Z.C. Mines, Broken Hill, NSW. This has been in operation for a four month period (January, 1988). The purpose of this application was to provide computer assistance to mine planning engineers and blasthole design draftsmen for the longhole design process, particularly by: 1. reducing the- volume of tracing, drafting and geometric manipulation which is a significant feature of the manual design process, 2. providing additional design drawings to enhance the conception and implementation of stoping design.

Jan 1, 1988

In looking towards 2000, it is more than appropriate that we look back on the history of diamond drilling to give us a better understanding of where we have come from and see the significant advances that have been made.

Jan 1, 1992

By Misra A

The development of roadways in underground mines in Autralia is by conventional continuous miner technology. The rate of development achieved using this technology is improved by modifications to this technology using additional equipment such as surge cars or decreasing roof bolting time.Development rates achieved with this technology compare with developing technologies such as high capacity continuous miners, continuous transportation and simultaneous cutting and bolting systems such as the Kemcol Beaver. Pillar dimensions have an effect on the rate of development.'

Jan 1, 1991

By K Uchino, M Inoue

Self-potential anomalies are generated by fluid pressure gradient, by temperature gradient or by chemical gradient. On the basis of this principle, a new technique is proposed to locate the fire source of spontaneous combustion of coal by the self-potential method. In order to investigate whether this method can be applied to locate the spontaneous combustion of coal in practice, surveys of self-potential distributions were undertaken in a coal waste pile undergoing spontaneous combustion. The results showed that there is a negative centre of the electrical potential distribution in the measurement area. The potential in this centre is about 140 mV lower than that in the surrounding area. Moreover, the negative centre of electrical potential distribution almost overlaps with the high temperature zone. Therefore, it is concluded that it is possible to locate the heat source by the measurement of self-potential distribution.

Jan 1, 2005

Within the Business Process Improvement Program initiated at Placer Dome during 2003 was the Business Performance Management Project (BPM).BPMÆ s aim has been to extract productivity improvements from individual business units by providing a model for implementing leading practice based management process within the Placer Dome Group, sharing management best practice, injecting new management techniques and instilling a continuous improvement culture. The installation of an underground dispatch system has been a key component of the BPM project at Osborne Mine.Information capture and analysis allows for corrective action to be planned and executed before there is a material impact on the performance of a business unit. This paper briefly describes the principles and practices of effective business performance management, the four processes of a management operating system namely; strategic and tactical planning, implementation and reporting. The identification of business drivers, their measures and associated key performance indicators is discussed. The benefits of an underground dispatch system at Osborne with respect to safety, production and maintenance is described along with the installation process within the mining department that included its configuration, resourcing and roll out.

Jan 1, 2005

Any engineering firm hoping to do business in the modern world must understand-and take into account-the social and economic realities of client, country, culture, and community. If these considerations are ignored, any large-scale international development project is doomed to failure even before it begins. In this changing world, the distinctions between `developed', `developing', and `less developed' nations are more and more blurred. The so-called `less-developed' and `developing' nations are rapidly acquiring technology, an educated man- agerial and technical class, manufacturing capa- bilities, a growing spectrum of developed financial and raw materials resources, and a broad range of labour skills. These nations are establishing themselves as an integral part of the modern world, on an equal footing with other nations and with justifiable expectations for an ever higher standard of living and an ever better quality of Life.

Jan 1, 1978

By Ketteridge IB, Mulcahy DE, Quast KB

The long term energy demands in South Australia are such that there is a distinct possibility that one of the lignite deposits in the State will be exploited to feed a pulver- ised-fuel power station. Bowmans lignite deposit is the largest lignite deposit in South Australia and is considered to be a contender. The deposit is ideally situated (100 km north of Adelaide) but the quality of the lignite is poor (see Table 1). TABLE 1

Jan 1, 1984

Exploring for deep shallow dipping orebodies can be very expensive and very difficult. Surface exploration is often not an option and obtaining the best location for underground drilling can cause production delays if drilling is carried out from development headings. The Otter/Juan mine has been in production for approximately 34 years. All of the production is now sourced from more than 1000 metres below the surface from an area known as the Edwards Lode. The orebody is shallow dipping and open at depth. Exploration drilling has been performed from decline stockpiles and from hangingwall drill drives. Drilling from footwall positions (eg decline stockpiles) into shallow dipping orebodies can often produce intersections which are unusually thick thus leading to optimistic resource figures. The decision to develop a dedicated hangingwall drilling position can vastly improve the quality of the data used to generate an orebody model. In 1997 a new extension to the Edwards Lode was discovered and named the æFÆ surface. In 1999 a resource calculation was performed using data obtained from drilling that was carried out from decline stockpiles. In 2002 a dedicated drill drive was developed into the hangingwall of the æFÆ surface to obtain better data to verify the previous resource calculation. For this case study obtaining more representative data reduced the resource estimate by 66 per cent. This information was obtained early enough to allow for alteration to the mine plan and without loss of capital.

Jan 1, 2003

Roasting of zinc concentrate at the Risdon Works of the Electrolytic Zinc Company of Australasia Limited, (E.Z.), is carried out in two fluid bed roasters capable of treating 450000 tonne/yr, or sufficient for the output of 220000 tonne of salable zinc. The furnaces were constructed by Lurgi, Australia, to the basic design developed by Vieille Montagne Company of Balen, Belgium. The advantages of fluid bed roasting include a higher metallurgical efficiency in sulphur oxidation from a feed which does not require any pre-grinding, mechanical reliabil- ity through the absence of any moving parts within the furnace and the capability of being scaled up to a large unit.

Jan 1, 1977