Search Documents

The Burra Burra Aline is in complexly folded Torrensian dolomites and limestones forming the faulted axial region of a major anti cling. The orebody mined was largely of secondary origin and confined between two faults, Kingston's on the west and Tinline's on the east. The orebody occurred at the junction between cherty dolomites and a clastic limestone with a large mass of marble breccia along its western margin. Secondary ore consisted of carbonates and oxides in the breccia and the ore bed and detrital copper minerals deposited. As part of a clastic breccia in sink holes and solution cavities in the dolpthites and ore beds.Primary sulphides occur disseminated in the marble breccia and in stratiform habit in the ore bed. Kingston's so-called 'Lode' may be mineralised marble breccia.The marble breccia appears to be of diapric or sedimentary origin and there is evidence to support a sedimentary origin for some 'of the copper sulphides. No igneous rocks have been discovered within 20 miles of the mine and any hydrothermal activities were probably at comparatively low temperature. The possibility of extensive stratiform and disseminated copper sulphide mineralisation in the marble breccia and ore bed requires testing by further drilling and geophysicalsurveys.

Jan 1, 1963

By J Mauk

Water-rock reactions such as pyrite oxidation and calcite dissolution strongly influence the pH of pit lakes that develop in open-cast mines after mine closure. The Martha Mine, located in world-class epithermal Au-Ag deposit at the southern end of the Coromandel Peninsula, New Zealand, is scheduled to close in 2007, after which the pit excavation will be rehabilitated into a recreational lake; the first pit lake in New Zealand. Mineral distribution maps from XRD results of 130 andesite samples identify regions that could produce or consume acidity in the future pit lake. Maps show pyrite, calcite, adularia, albite, illite and chlorite distribution in the wall rocks. These data identify five alteration mineral associations: potassic, propylitic, weathered, oxidised and weakly-altered. Pyrite occurs in potassic, propylitic and weathered associations, whereas calcite is restricted to propylitic association in the northeast wall. Subaerial, epilimnion, and hypolimnion exposure zones describe the physical and chemical weathering processes that are likely to occur in regions of pit wall, and the potential effects on lake water chemistry. The pH of epilimnion water will depend on the relative abundance of pyrite and calcite in the propylitic association in the northeast wall, whereas hypolimnion pH will depend upon the frequency of whole-lake circulation events that distribute dissolved oxygen to deep lake layer. In mines with diverse alteration associations, mineral distribution maps are an essential precursor for accurately estimating water-rock reactions in pit lake environments. Data may be directly incorporated into a quantitative geochemical model of future pit lake water chemistry.

Jan 1, 2002

By Simmons SF, Fleming J

Alteration and mineralisation at the Island Copper deposit is related to the intrusion of Early Jurassic quartz feldspar porphyry dykes into surrounding comagmatic Bonanza volcanic rocks. The pyrophyllite alteration zone forms an upward flaring cone, largely hosted within a breccia body that c ross-cuts the Cu, Mo, and Au-rich ore shell. This alteration zone contains pyrophyllite, dumortierite and diaspore and resembles alteration occurring in some high-sulfidation deposits, but which is barren. Fluid mineral equilibria and fluid inclusion studies indicate formation at approximately 300 ¦C from fluids dominated by steam and gases. These fluids appear highly acidic, but sulfur poor, leading to extreme base leaching within the breccia body and surrounding rocks.

Jan 1, 1995

Better quality at lower cost is today's formula for remaining competitive in a world market. For an integrated steel company, high quality low cost steel production must originate before the blast furnace. In 1979, when U.S. Steel initiated a Quality Management Program throughout its steelmaking operations, efforts began at the coal, ore and flux mines. The objective was to improve the quality and reduce the variability of the critical parameters for steelmaking raw materials, to get the blast furnaces, and subsequently the melt shops, under optimum control. The general details of U.S. Steel's Quality Management Program are discussed and how it was used to promote the desired improvements in steelmaking raw materials. Some of the outstanding results obtained by the cooperative efforts between the mines and the steel plants are reported. The lessons learned by U.S. Steel were through upgrading existing operations and facilities. These principles should now be applied to new projects and the benefits of good quality management should commence from the time new projects are Commissioned.

Jan 1, 1986

After the minim operation, most raw materials that occur in the earth's crust require some form of processing or refining before they can be converted into a final end product. In the mineral industry these remarks apply to materials such as iron ore, bauxite, limestone, copper ore and many others that are found in Australia in large quantities. Processing plants for these raw materials operate more efficiently, however, if the feed to them is consistent in both physical and chemical characteristics. Such uniformity rarely occurs in nature so that some form of homogenisation, or blending, is required ahead of the processing plant. Bending also assists the mining operation itself by reducing; the need for selective mining and, by combining high and low grade materials, a more uniformly graded, commercially acceptable product can be obtained, thereby increasing the commercial life of a mine or quarry. Bed blending is the most efficient of the processes available, and following its development in the United States in 1905, over 100 plants have been installed, or are under construction, all over the world. The original process, the Robins--Nessiter system, has been the subject of continued improvements and refinements, so that economical capacities are possible from less than 100 l.t.p.h. up to 10,000 l.t.p,h. and beyond.

Jan 1, 1969

By Yesil MM, Bozdag T

This paper describes the conver- gence and load measurements carried out in inclined seams at five longwall faces, two of which were supported by hydraulic props and the other three by conventional timber supports in Karadon-Gelik mine. The minimum support capacities determined in this study are compared with the results obtained from two empirical approaches suggested by Wilson (1975) and Jacobi (1981). The characteristics of hydraulic props to be used and support patterns in the longwalls are found, conclu- sions are drawn and suggestions are made. Design nomograms are prepared for field engineers, in order to be able to approach the problem more confidently and realistically.

Jan 1, 1992

By Joussemet R, Fabre F

The paragenesis of the Escuzar Mine (Andalusia-Spain) comprises: ò major constituents: celestite and carbonated minerals (abundant calcite and less frequent strontianite). ò minor constituents: sulphates (gypsum and anhydrite), clays and some iron oxides and hydroxides. The average content is at about 60 per cent SrSO4. Since liberation size was fine (from 30 to 50 ¦m), the flotation method was chosen. Laboratory batch tests have shown the relevance of using alkylsulphates with as long as possible hydrocarbon chains. The recovery obtained led to an expected 95 per cent SrSO4 concentrate with nearly 70 per cent recovery. Pilot plant tests (160 kg/h) have confirmed these results and attained a recovery of more than 65 per cent of a 96 per cent SrSO4 concentrate. Extrapolation to the industrial scale (14 t/h) has been successfully carried out : up to 600 t of a concentrate at more than 95 per cent SrSO4 has been obtained. Non optimised recovery has already reached 60 per cent for a 97 per cent SrSo4 concentrate.

Jan 1, 1993

By B Cope, N Hastings, D Webb

A Feasibility Study was completed in late 2002 to ascertain the risk and reward profile from the proposed deepening of operations at Perseverance Nickel Mine in Western Australia. The system and approach adopted to this brownfields extension work is outlined and the main components of the study are overviewed. In particular, emphasis is given to the integration of mine design and scheduling tools through to financial evaluation. Detailed comment is given on the ability of the system used to provide a robust project schedule complete with 3D animation. The level of importance in eliminating scheduling errors is demonstrated in relation to the reported bottom line viability of the project. It is suggested that this is an area where brownfields Feasibility Studies have lacked clarity and authenticity, leading to the creation of an unrealistic benchmark for project implementation.

Jan 1, 2003

By Streichfuss M, KeBler H-W, Burgwinkel P

This paper describes the design of an expert system used as a part of a diagnostic system for diesel hydraulic drives. A PC-based diagnostic system ruDi (KeBler and Burgwinkel, 1993) was developed to minimise the time for diagnosis and repair work of vehicles with diesel hydraulic drives used in the mining industry. One part of ruDi is an expert system that helps to locate errors in any of a vehicle's subsystems, and supports technicians in removing the cause of a malfunction. Apart from the standard knowledge of diesel engines and hydraulic transmissions, the expert system supports the interpretation of the data obtained during sophisticated engine analysis tests such as high-resolution speed analysis or high-pressure analysis of the diesel injection system. The expert system is designed to diagnose various vehicles of the same type. Data for each vehicle is stored separately allowing checks to be carried out individually for each machine. An additional feature of this system is a database interface to a Maintenance Planning and Control System (MPCS) that allows an automatic generation of work orders for the defects found during the expert system sessions.

Jan 1, 1995

This is the second of a series of papers dealing with Geology in Exploration. The first, published by the Australasian Institute of Mining and Metallurgy, Proceedings Nos. 143-144, 1946, was written as an introduction to the subject and employed the exploration geology of the Cobar field to illustrate the prospect thinking. This paper will be concerned with the problem of ore repetition in depth and borrow its- example from the Mount Lyell copper field. The writing will be taken up altogether by the example. Nevertheless the intention remains to develop the subject in terms of its wide interest and application.The Mount Lyell field possesses large actual and prospective resources within, and in the vicinity of, the known deposits. This paper does not bear at all on these accessible ore reserves and tangible prospects. There is also in this area evidence of deep ore. The possibility is of little practical interest at present. But the picture of ore repetition, exemplified by the Mount Lyell field, does matter now to the outlook on exploration in this country. For once this essential feature of ore occurrence is widely understood there may develop, on the scale warranted, the search for major deposits which do not outcrop but which are still at shallow depths because of the part erosion plays in this story of concealment and exposure of ore. Also there is the chance in some fields (including Mount Lyell) of a second harvest of orebodies within mineable depths. This exploration goal, introduced in the first paper, will appear more clearly as the Geology in Exploration series is written up. Here the concern is to show the character of the geological evidence which points to the occurrence and recurrence of ore in the earth's crust, the picture at the foundation of this exploration scheme. There is considerable information in the Mount Lyell area of the structures...

Jan 1, 1947

By Whiten WJ

A method that allows data to be mass balanced and screen models to be fitted in a single step is described. The inclusion of several variables to describe the feed data in the fitting procedure allows a mass balance to be conducted at the same time as the fitting of the screen model. Analysis of Groote Eylandt Mining Company screening data has demonstrated that this method is ideally suited to applications where complete stream data are not available. Also, certain random fluctuations in screen model parameters arising from the fitting of consecutive mass balances and screening models are significantly reduced. A cubic spline function with fixed knot positions corresponding to particle sizes and variable (fitted) cumulative percent passing values is used to describe the feed size distribution. When the spline function is interpolated at the experimental feed particle sizes a fitted feed size distribution is obtained. This feed size distribution is then used as input to the screen model calculations from which product size distributions are generated. Since both feed and product size distribution data are used to minimise the residual errors between the observed and fitted stream size distributions, a mass balance is Conducted simultaneously with the screen model parameter fitting.

Jan 1, 1984

By Childs G, Ritchie IC

This paper describes the principle and operation of small hydrocyclones for use in the coal, minerals and other process industries. The principles for selecting a hydrocyclone for an application are also discussed. Typic- al uses and installations in various industries are described.

Jan 1, 1984

By T P. Hynes

Submarine tailings disposal is conceptually an attractive option for managing reactive mine wastes in coastal regions by virtue of reduced sulfide oxidation under a water cover and no infrastructure to maintain after mine closure. However, the lack of detailed knowledge of metal leaching, dispersal of fine tailings and biological impacts in the marine environment has led to no operating permits currently in effect in Canada. Detailed chemical and ecotoxicological assessments at two historic copper mine sites (Little Bay and Tilt Cove) in the north coast of Newfoundland with tailings disposed in an estuarine to shallow (=100 m) marine environment have demonstrated reduced reactivity of sulfidic tailings when submerged under water. Only non-acute toxicity is detected in biota inhabiting the immediate vicinity (A review of another historic shallow marine tailings operation in the southern tip of Vancouver Island (Jordon River) with a high-energy setting also reveals problems with unconfined tailings dispersal and temporal biological impacts. Documented studies at two deeper (140 - 360 m) marine tailings disposal operations at the northern tip of Vancouver Island (Island Copper) and northwestern coast of British Columbia (Kitsault) again illustrate imperfect predictions of tailings re-suspension and dispersal. At these sites, bioaccumulation of tailings-derived metals appears to be minimal. There is evidence of rapid re-colonisation of the tailings surface by benthos but of different species than the original population. Integrating these observations with reported metal fluxes and biological diversity associated with submarine hydrothermal vents, the risks and benefits of deep-sea (>1 km) tailings disposal are discussed. To determine if submarine tailings disposal in deep, confined basins on the seafloor is environmentally friendly, detailed multi-disciplinary research incorporating physical, chemical, biological and toxicological components will be indispensable.

Jan 1, 2003

Exploration risk increases with time, due to a general decrease in prospectivity as the more accessible deposits are found, and be- cause of rising costs and demands due to an improving standard of living. Risk is separated into financial risk, which increases sharply at the development stage, and the risk of failure which is at its peak at the outset of exploration. Risk is also divided into internal and external factors; some of the latter cannot be offset, viz. the systematic overall risk for any enterprise. The recently emergent risk embodied in withdrawal of large areas from exploration access is discussed. An appeal is made for objective multiple land-use policies to be applied so that land remains available at reasonable cost and with appropriate environ- mental safeguard conditions. Risks specific to gold exploration are discussed. As gold now accounts for over 50% of all mineral exploration, and most other metals are depressed, any sharp decline in gold will have grave effects on the ex- ploration industry. Gold exploration will become more difficult and expensive in about five years, after most of the readily accessible deposits in Australia are found. Government's role is important in pro- viding stability and basic data at reasonable cost. Exploration for specific minerals or of particular areas could be stimulated by extending the 150%.tax deductibility of R & D to aspects of exploration of strategic im- portance, particularly in the event of a downturn. Exploration is classic scientific research, at least through to the proving Stages.

Jan 1, 1987

By Klenowski

Rational design of layouts for longwall operations is greatly facilitated by use of an accurate and economical method for predicting stresses and displacements. The displacement discontinuity method (a form of boundary element method) is based on replacing actual excavation geometries by thin slits of the same plan area. This approach allows three-dimensional stress- analysis at a fraction of the cost of alternative methods. The analyses can be readily performed on economical microcomputers, putting the analysis capability within the reach of mine-site personnel. This paper describes investigations associated with the German Creek Central Colliery, the first longwall operation in Queensland's Bowen Basin. The material properties used in the model, in particular the rock mass and goaf properties, have been 'tuned' to fit stress measurements obtained during extraction of the first and second longwall panels at the mine. The study shows that model predictions based on suitably scaled anisotropic rock strata properties are in good agreement with the stress measurements made to date. This model predicts average chain pillar loads significantly higher than predicted by models based on United Kingdom conditions. A working chain pillar design method is proposed using average pillar loads predicted by the numerical model and ultimate strength characteristics given by Bieniawski's formula.

Jan 1, 1988

By Fraser C. J

The township of Yalloum was established in 1921 to provide accommodation for the work force on the sites of the power station and open cut which were to become the basis of Victoria's electricity industry.A company town, Yallourn flourished, and in its heyday in the 1950s the township had a population in excess of 5500 residents.However the town was sited over a valuable coal field. In the 1960s, studies conducted by the State Electricity Commission indicated that excavation of this coal as a continuing development of Yalloum Open Cut was the optimum choice to meet the growing energy needs of Victoria. Operation in what became known as the Township Field commenced in 1979 and the completion of the overburden stripping was successfully achieved on target in 1991.

Jan 1, 1992

By Vidalinc, Raffoux

Longwall faces producing in the order of 20,000 tons per day of raw coal are presently running in the Houilleres du Bassin de Lorraine of Charbonnages de France. Production levels of twice that level pose some technical and economic problems of coal cutting, ventilation, coal and equipment transportation in the.face and from the face to the sur- face. The peak productions of the equipment in use today, the results of trials with new equipment, the utili- sation of forecasting models (some in the form of software), allow us to fo- resee feasable technical solutions to these problems. They will first be considered in the best possible context (thick- ness, dip, non gassy, soft coal, good strata, no faults). This will give. the necessary conditions to reach daily output'of that level. A sensitivity analysis of these- figures to the effective natural con- ditions will then be undertaken and the implication of such a project on health and safety (dust, climate ...) will be carefully considered. A concise technical and econo- mical approach will permit us to fore- cast the economical interferences of such production units and specially the consequences of sudden variations of the output (downtimes, failures, etc). From this investigation, goals for technological development and re- search areas will be outlined to be able to reach this production target in the XXIst century.

Jan 1, 1988

By Guarascio M, Massacci P

In process simulation, more reliable prediction of industrial results and evaluation of data for design purposes and process optimisation may be attained by the combined use of: the modelling and simulation of ore characteristics, and 2. the modelling and simulation of the process. It is well known that geostatistical methods allow the defining of models of orebodies in which the variables considered are the grades of the valuable components. These models are proper for reserve estimation, geostatistical contouring, design and simulation of the exploitation method, and, in addition, for evaluating the variability of the ROM which is expected to be fed to the processing plant. However, no data are normally incorporated in the orebody model in order to evaluate the ore characteristics relevant for a reliable process simulation. The procedure for process simulation aimed at predicting plant results normally used so far consists in collecting samples from different orebody sites and building up a so-called 'representative sample'. On this sample, the ore characteristics (eg liberation, washability, grindability, etc) and the processing tests are referred to as the 'average behaviour in the orebody', assumed constant. A more reliable methodology consists in collecting samples from different orebody sites, in performing tests to characterise the samples from the point of view of the process (ore patterns), and in using synthetic parameters (process features). The values of the parameters are processed using geostatistical methods in order to develop a model for simulating the feed to the process. The estimation may thus be referred to the amount of recoverable minerals instead of to the existing minerals. Furthermore, the selection of the processes, the sizing of equipment and the design of control devices, as well as the prediction of results, become more accurate and reliable.

Jan 1, 1993

By Little T. N, Bettess D

For many mining operations the challenge of equalling World Best Practices has become the key motivator for increasing mine productivities and for lowering total costs. In most instances this will only be achieved if mines optimise their total system rather than minimising specific costs within unit operations. In the past, drilling and blasting have been viewed as a cost to be minimised rather than operations which should have their impacts fully leveraged. Once a hardrock orebody is defined the activity which has the most substantial impact in determining the efficiency of a mining operation is the blasting. The output from a blast affects every downstream operation; only by understanding the extent and interactions can the mine be optimised. Substantial improvements to hardrock mining, quarrying and excavation operations are achievable. Instead of seeking the regular one to three per cent improvements based on reduction of consumables, mine operators would be well advised to go for much bigger targets of ten to 30 per cent by fully leveraging the drill and blast operations.

Jan 1, 1995

By Breen AM, Phelan JM, Doherty RJ

Early in 1990, Pancontinental Resources (Base Metals) Pty Ltd commenced flotation treatment of ore from the complex copper-lead-zinc sulphide orebody at Thalanga, 65 km west of Charters Towers in North Queensland. The orebody consists mainly of primary sulphide ore but also contains a substantial proportion of supergene ores which are being processed during the first year of operations. The supergene ores are of three main types, designated as A, B, and C. Supergene A ores are essentially copper ores, containing little lead and zinc, while B and C ores are copper-lead-zinc ores with different degrees of alteration of the original chalcopyrite and different ratios of copper to zinc content. Copper is present in the supergene ores mainly as chalcocite, digenite and covellite. Lead and zinc occur mainly as galena and sphalerite respectively. This paper describes the development of flotation plant practice, aided by laboratory testing, to process the supergene ores. The major challenge in treating these ores is that a varying proportion of the sphalerite is naturally activated and is not easily depressed in flotation by the conventional zinc depressants.

Jan 1, 1991