Search Documents

By R Williams, P Kohout, J Comins

The Northside Storage Tunnel (NST) is the largest tunnelling project ever undertaken in Sydney. The tunnel extends deep underground from the western bank of the Lane Cove river to the North Head sewage treatment plant (STP), with a branch tunnel from Scotts Creek connecting to the main tunnel under Tunks Park. The aim of the tunnel is to intercept wet weather overflows from four key points along the northernsuburbs ocean outfall sewer (NSOOS) and provide short-term storage and transfer of sewage to NorthHead STP for treatment prior to discharge to the ocean through the deep ocean outfall. The project was an ambitious undertaking by an alliance between the client Sydney WaterCorporationand the engineering firms of Montgomery Watson, Connell Wagner and Transfield to design andconstruct approximately 20 kilometres of tunnel, tunnel declines and shafts in just over three years. In order to achieve this tight timeframe construction of the NST has been undertaken simultaneously at seven construction sites located across the northern suburbs of Sydney. As with most tunnelling operations, tunnel boring machines (TBMÆs) and roadheaders dominated the excavation activities. Tunks Park and North Head STP are the major tunnelling sites. An access decline was excavated using roadheaders at both of these sites to facilitate tunnelling using TBMÆs. Three TBMÆs 3.8 m, 6.0 m and 6.3 m diameter) were launched from Tunks Park and one TBM (6.5 m diameter) was launched from North Head. At the overflow interception sites of Scotts Creek, Lane Cove River and Quakers Hat Bay two vertical shafts known as drop and access/ventilation shafts were constructed. These shafts would provide the linkage between the existing sewer and the tunnel. As their names suggest the drop shaft would convey the wet weather sewage overflows to the tunnel while the access/ventilation shaft would provide access during dry weather and ventilation during a filling event. The fourth overflow site of Tunks Park would use the tunnel decline as its link to the tunnel. Originally these shafts were to be excavated using the raise bore method. This technique however, is entirely dependent on the TBMÆs reaching the shaft locations at the specified time. This was not the case at two of the three shaft excavation locations and top down methods of excavation such as, a percussive cone fracturing (PCF), blind bore, mechanical excavation and drill and blast were investigated to ensure the project met its completion schedule. Traditionally project decisions are dominated by cost and schedule objectives. The contractual arrangement of the Alliance however, required that the objectives of safety, community and environment also be considered in any decision making process. Thus each of these top down methods of excavation were assessed against these five objectives. On considering all of these factors the use of explosives was considered to be the superior technique.

Jan 1, 2001

By Ross J. F

A pillar 'is a block of coal left in the first working of a coal seam for the purpose of supporting the superincumbent strata in such a manner that the winning out roadways will be safe to traverse by men and by the coal transport system.PRINCIPLES OF PILLAR EXTRACTION.The size of a pillar is chiefly dependent on the depth of cover, and in a lesser degree on the nature of the coal, or the condition in which the seam has been laid down. In a seam at 1,100ft. depth of cover, and assuming a spec'ific gravity of 2.5 overall for the cover strata, a pressure of 1,200lb. per sq. in. is the loading on the top surface of the coal seam before mining begins.When mining commences, and as the pillars are formed, an increased load is imposed on the coal left in the pillars, according to the percentage of coal extracted in the first working. Thus, if 25% extraction is taken in the first working, the load on the pillars is theoretically increased from 1,200lb. per sq. in. to 1,600lb. per sq. in. over the area mined. If this state of things went on indefinitely it would not be possible wholly to extract a pillar because of the extreme pressure tliat would be thrown on the diminishing portion; but, fortunately, another element, that of time, enters into and assists the process of extraction.If the superimposed strata were of an entirely plastic nature, this time factor could not operate, as the cover weight would settle instantly on the remaining portion of the p'illar and finally overwhelm it. The cover strata above a pillar generally have a certain rigidity which does not allow the superimposed weight to settle instantly on the pillar fraction, and it requires a period of time to elapse before the extra weight is felt by the pillar.The time factor varies widely, and is governed entirely by local conditions; it can only be determined by experience gained on the spot or in close proximity to the area of operations. It is dependent on the strength of the strata and its characteristics under bridging conditions.It is, therefore, logical to assume that the more rapidly a pillar can be extracted the greater will be the safety factor and also the percentage of recovery of coal.Up to the present time, the operation of the extraction of pillars in this country has been, with a few exceptions, a manual one, and before mechanization of Collieries can be fully accomplished, the process will have to be performed mecharrically.

Jan 1, 1947

By J deVries, A Broodryk, P Kyselica, K McLean

Gwalia gold mine is located close to the town of Leonora in the Goldfields region of Western Australia, some 830 km from Perth. The mine is wholly owned by St Barbara Ltd, an Australian Securities Exchange listed gold producer and explorer. The Gwalia mine is a deep, all-trucking mine and is serviced by a 10 km long decline from surface. Mining is currently 1540 m below surface. Reserves extend to 1820 m below surface and are open at depth. The mine produces in excess of 200 koz of gold per annum.The Leonora area is hot and arid, with a mean annual rainfall of 230 mm and a 95 per cent mean daily maximum temperature of 20.3°C wet-bulb and 35.6°C dry-bulb.The primary ventilation system comprises a 490 kg/s surface exhaust fan, which draws air down a parallel intake system consisting of the decline, and a dedicated fresh-air intake system extending to the bottom of the production zone. Cooling is provided via a surface bulk air cooler serviced by an ammonia refrigeration plant that delivers 150 kg/s of chilled water to the bulk air cooler.The refrigeration plant and bulk air cooler were installed in 2008. The design allows cooling to be increased over time by installing an additional refrigeration plant in a lead lag configuration with the current refrigeration plant when required.Since 2008, expansion and increased depth reached a point where the underground heat load exceeded the installed capacity of the existing 4.0 megawatt rated (MWR) refrigeration plant. In order to maintain the mine design conditions underground, upgrading of the existing refrigeration system was required to bring the cooling capacity to 7.5 MWR.Two expansion options were considered: the addition of an ammonia vapour-compression refrigeration machine similar to the existing one or a lithium bromide absorption refrigeration system using waste heat from the site power station. The original design and layout of equipment on-site meant that either could be used, allowing an assessment of the merits of both when additional cooling was required.The decision was made to install a lithium bromide absorption system on the lead side of the existing ammonia refrigeration plant. This arrangement provides considerable economic benefits, including reductions in site-generated electrical power, generator fuel consumption and carbon dioxide emissions.This paper details the planning, design, installation and commissioning of the absorption chillers.CITATION:Broodryk, A, deVries, J, Kyselica, P and McLean, K, 2015. The design, installation and commissioning of an absorption refrigeration system at Gwalia gold mine in Western Australia, in Proceedings The Australian Mine Ventilation Conference, pp 193–200 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 31, 2015

By D Kubik, K The

The New Zealand (NZ) Transport Agency’s Waterview Connection will complete Auckland’s Western Ring Route, a 47 km north–south motorway alternative to Stage Highway 1. The project is being delivered by the Well-Connected Alliance comprising the New Zealand Transport Agency (NZTA), Fletcher Construction, McConnell Dowell Constructors, Obayashi Corporation, Parsons Brinckerhoff NZ, Beca Infrastructure and Tonkin & Taylor.The project involves construction of 5 km of new motorway, nearly half of it underground connecting State Highway 20 (SH20) to State Highway 16 (SH16). The underground portion of the project incorporates twin 13.2 m inside diameter (ID) tunnels 2.4 km long, each carrying three traffic lanes, one for north-bound traffic and one for south-bound traffic. The tunnels are being driven by a 14.46 m outside diameter (OD) 2400 t, tunnel boring machine (TBM) shield that was assembled and launched at the southern portal. It will be turned and re-launched at the northern portal for the return drive to the southern portal where it will be disassembled. This paper presents two major temporary works elements contributing to the successful launch of the TBM: the TBM assembly crane platform and the TBM shove frame and associated components.Tunnel boring machine shield assembly – crane platformThe TBM shield was delivered to site in subassemblies ranging in weight from 100 to 380 t. It was initially proposed to use a 750 t crawler crane sitting above the tunnel portal headwall to assemble and disassemble the TBM. However, this did not have sufficient capacity to allow the TBM shield to advance clear of the tunnel before disassembly commences. To reduce the crane’s working radius a temporary steel crane platform was developed that is supported on the side walls of the tunnel approach trench. This has enabled a smaller, less expensive, 600 t crawler crane to be used and will allow the TBM shield to clear the tunnel before disassembly.Tunnel boring machine launch – temporary worksTo launch the TBM a purpose built steel frame was required for the TBM thrust rams to react against. The shove frame had to be able to transfer the thrust loads from the TBM shield to the ground below and thrust wall behind. A range of potential thrust loads and jacking patterns were examined to develop the design load cases for the shove frame. The shove frame was used to launch the TBM at the southern portal and to re-launch it at the northern portal. Elements of the shove frame will also be used to support the portal faces during the TBM arrivals.CITATION:Kubik, D and The, K, 2014. Waterview Connection – temporary works for tunnel boring machine?launching, in Proceedings 15th Australasian Tunnelling Conference 2014, pp 281–288 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By A Fareth

Constructed between 1885 and 1891, the New Croton Aqueduct (NCA) in New York State is a 50 km long (31 mi) brick-lined tunnel conveying water from the Croton watershed north of New York City to distribution systems in the Bronx and Manhattan. Except at two siphons, the aqueduct operates as an open channel conduit from the New Croton Reservoir downstream 39 km (25 mi) to the Jerome Park Reservoir in the Bronx. The remaining 11 km (6 mi) is operated as a pressurised conduit and includes a major siphon, of circular cross-section, under the Harlem River. The aqueduct has a flow capacity of approximately 1100 million litres of water per day (13 m3/s or 290 million gallons per day) and supplies on average ten per cent of New York CityÆs drinking water. The CityÆs water supply system is operated and maintained by the New York City Department of Environmental Protection (NYCDEP). This paper covers the work done during the three main stages of the program to rehabilitate the entire NCA: inspections, design and rehabilitation. It also includes some of the more interesting structural findings of the original construction as well as documents and drawings from the NYCDEP archives. The rehabilitation program has been underway in phases since 1993, with inspections scheduled to minimise outages, allowing this strategic aqueduct to remain in service during critical seasonal periods. The open channel flow section of the aqueduct in the north is horseshoe shaped, with inside dimensions of 4.1 m (13.6 ft) in width and 4 m (13.5 ft) in height. The pressurised section is 3.7 m (12.3 ft) in diameter, and includes a 90 m (330 ft) deep siphon under the Harlem River. A total of 163 million bricks were used in the construction, enough to build a 48 km (30 mi) wall around Manhattan Island, 3 m (10 ft) thick and 15 m (50 ft) high.Between 1993 and 1997 a series of in-tunnel investigations were performed in the open channel portion of the NCA, consisting of field inspection, non-destructive geophysical testing, and coring of the brick liner. Between November 2004 and September 2005, a major inspection program was conducted to assess the condition of the 11 km (6 mi) long pressurised section and all shafts, headhouses and blow-off structures along the entire 50 km (31 mi) alignment. Inspection methods included using an underwater remote operated vehicle (ROV) equipped with sonar and cameras to inspect the deep siphon, fibre optics examinations of probe holes drilled through and beyond the brick lining, and core holes and geophysical inspections to assess properties of the liner and behind-the-liner materials. A water pressure and test grouting program was conducted to assess methods and expected grout takes for the rehabilitation work in the pressurised sections. The rehabilitation program is anticipated to be completed in 2010.

Jan 1, 2008

By B Smith, R Gelson

Springvale Colliery is an underground longwall mine situated approximately 10 km north-west of Lithgow in the western coalfields of New South Wales. Following a full-scale review of the mineÆs ventilation system in mid-2010, it was clear that the mine by early 2013 would become ventilation constrained as a result of the increasing size of the mine workings, the predicted worsening tailgate conditions and plans to introduce a fourth continuous miner unit. This realisation led Springvale to embark on a major upgrade of the mine ventilation system that would meet short-term and life-of-mine (LOM) requirements.Included in the upgrade project was the installation of a new high pressure centrifugal main exhaust fan that is capable of overcoming the high resistances imposed frequently on the circuit by restrictions in the tailgate airway. The new fan featuring a 2.5 MW motor is designed to be capable of operating at a quantity of 250 m3/s at a pressure of 7.9 kPa, a substantial improvement over the previous system, which had an operating duty of approximately 145 m3/s at 1.9 kPa. The new fan is of a centre hung design and features a backup diesel motor to maintain ventilation in the event of a power outage.Structural engineering analysis determined that under the operation of the new main fan the existing standard of ventilation control devices (VCDs) at Springvale would not be adequate to withstand the increase in differential pressures. As such, an upgrade of critical VCDs was undertaken utilising a novel high flexural strength (9 MPa) shotcrete and thin spray-on liner, which help serve to safeguard the structural integrity of the appliances and prevent increased leakage as roadway conditions at VCD sites deteriorate over time (a serious problem in many areas of the workings at Springvale).In addition to the main ventilation system upgrade, a separate upgrade focusing on improving development face ventilation was also undertaken. This upgrade included the purchase of two high capacity (22 m3/s) variable inlet vane (VIV) auxiliary fans to facilitate comfortable development face ventilation.The upgrade of the mine ventilation system at Springvale has been three years in the making, but has removed a major business risk in that it has afforded mine planning and operational flexibility (a fourth unit can now be introduced) for the LOM, and importantly provided unprecedented levels of comfort to operators at the working faces where previously ventilation and heat issues were frequently reported. The impact of this on the morale of the workforce, and hence their output, should not be underestimated.CITATION:Gelson, R and Smith, B, 2013. Life-of-mine ventilation system upgrade at Springvale Colliery - A case study, in Proceedings The Australian Mine Ventilation Conference , pp 79-86 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

It would be a good thing when reviewing the challenges to be faced by the Australian gold industry to set the backdrop and scene for them, by briefly examining the history of this vital and dynamic industry in the Australian context. Gold mining in Australia had its official beginnings in 1851 when John Lister and William Tom discovered gold at YorkyÆs Corner, later renamed Ophir by Edward Hargraves. From that first tentative beginning, the ensuing rush of prospectors into New South Wales and Victoria meant that the annual gold production in those early years surpassed that of the next 40 years. This early rate of production was only eclipsed when AustraliaÆs production was once again lifted by the discovery of gold on the other side of the continent, in Western Australia. (Figure 1). The years leading up to the First World War saw Australian production peaking once again at over 115 tonnes of gold, a production rate that would not be surpassed until 1988. This renaissance in production at the beginning of the 1980s was achieved by the application of technology. The advent of bigger trucks and shovels meant that earth-moving costs dropped dramatically. This, coupled with the highly effective and efficient carbon-in-pulp processing route, stimulated the Australian gold mining industry into a state of frenetic activity. These two innovations were the principal factors that enabled the economic exploitation of the lower grade haloes left by the æold-timersÆ around the deposits exploited at the beginning of the last century-no high finding costs here. AustraliaÆs production through the 1980s and the early part of the 1990s was largely supported by the exploitation of these haloes. As these were depleted, the aggressive exploration effort stimulated by the strong cashflows of these early oxide deposits resulted in new æblindÆ discoveries which are now emerging as the backbone of the Australian industry (Figure 2). Gold production is a major contributor to the Australian economy. In 1998/99 the Australian gold industry accounted for approximately 16 per cent of the value of all mineral exports, which in turn accounted for over 35 per cent of AustraliaÆs total exports. As such, the Australian gold industry, by itself, accounts for just under six per cent of AustraliaÆs total exports (Figure 3). Consequently, the industry is responsible for over one per cent of AustraliaÆs gross domestic product. These statistics are all the more compelling when we consider that, at the beginning of the 1980s, goldÆs contribution to exports and GDP was insignificant (Figure 4). Within the Australian resources industry, gold mines and associated infrastructure account for ten per cent of all capital expenditure (Figure 5). From an employment point of view, in 1997/1998 the industry directly employed (excluding contractors) about 7700 people, approximately 15 per cent of all those employed in the minerals industry. Just under nine per cent of the workforce in the minerals industry are female, whereas in the gold industry over 16 per cent are female.

Jan 1, 2000

By J Jasper, L Koroznikova, J Begelhole

This paper outlines a comparison of heavy liquid and heavy suspension separation methods for iron ore characterisation.As part of Arrium MiningÆs program to improve its knowledge of ore types being processed in its two hematite ore beneficiation plants (OBP), metallurgical evaluation of hematite feed for the upgrading process has become a major focus.Iron ore deposits almost always contain more than one valuable (and relatively dense) iron mineral. Iron ores are found with a range of iron contents, giving rise to density variations.At present the industry relies on heavy liquid separation techniques for the evaluation of iron ore samples arising from exploration, mining or metallurgical processes. There are only a few high-density liquids available, which are both high-cost and highly toxic.Low-toxicity solutions that can be utilised at relative densities up to 3.0 have been developed. However, highly-toxic organic liquids are required presently to achieve relative densities beyond 3.0.Bromoform which has a specific gravity (SG) of 2.89, and diiodomethane (SG 3.31) are commonly used; both present significant health and safety hazards.æClericiÆs solutionÆ (mixtures of thallium formate and thallium malonate) provide liquids having specific gravities between 4.0 and 5.0. ClericiÆs solution is highly toxic and testing is currently conducted by a limited number of laboratories worldwide.An alternative to ClericiÆs solution and organic liquids is a low-toxicity, high-SG, suspension technique, which has been demonstrated successfully for heavy mineral sands. This heavy suspension method employs mixtures of fine tungsten carbide particles in lithium heteropolytungstate (LST) solutions.Heavy liquid separation is not commonly used as part of routine iron ore feed characterisation due to the expensive, toxic and time consuming nature of the technique. Our results show that the heavy suspensions method can achieve low-cost, low-toxic separation and are outlined and results compared with results using ClericiÆs solution presented.Heavy suspension technique provides a theoretical/absolute separation of a particular sample. By placing an iron ore sample in a suspension of a particular density, it produces two products: a sink fraction and a float fraction. As iron oxides-hydroxyoxides are denser than the gangue minerals associated with the ore, particles that have high iron content will sink and the particles with gangue association will float. This process is repeated over several densities, thus also enabling separation of the constituent iron ore phases. A theoretical grade and a theoretical mass recovery can be calculated. With these calculations, a grade-mass recovery curve can be constructed for any element that is of interest.This type of characterisation can be used to either prepare OBP feed-piles of known processing characteristics, or to benchmark the performance of the process against what can be theoretically achieved on a continuous basis.CITATION:Begelhole, J, Jasper, J and Koroznikova, L, 2013. Application of the heavy suspension technique for ore beneficiation plant feed characterisation from the Southern Middleback Ranges, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 269-278 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By H Q. Zhang, M C Chai, W Fu, H Y Chen, L M. Wei, Q J. Yang

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Fozichong deposit – located in the south-western segment of the giant Qinhang metallogenic belt, South China – is a large-sized lead-zinc polymetallic deposit. This deposit contains two main ore districts, termed as the Guyi ore district in the north and the Hesan ore district in the south respectively. We present an integrated data set on sulfide minerals, fluid inclusions and stable isotope (H-O-S-Pb) geochemistry to better understand the features and genesis of the Fozichong deposit.Field and paragenetic relationships indicate three mineralisation stages forming the early (Po+Sp+Gn+Ccp+Py+Di+Ep+Qtz), middle (Sp+Gn+Ccp+Py+Ep+Chl+Qtz) and late (Gn+Sp+Py+Qtz+Cal) sulfide assemblages respectively. Mineral chemistry – particularly S/Fe and Co/Ni ratios in pyrite, Zn/Fe, Zn/Mn and Zn/Cd ratios in sphalerite and Pb/Ag ratios in galena – indicates a magmatic association for the sulfide minerals.Quartz and calcite coexisting with the sulfide minerals of various stages host abundant fluid inclusions. Quartz in the early stage contains two- or three-phase CO2-H2O and liquid-rich aqueous inclusions, which have homogenisation temperatures of 162~365°C and salinities of 2.9~17.8 wt per cent NaClequiv, whereas quartz and calcite from the middle and late stages are dominated by two-phase, liquid-rich aqueous inclusions that have slightly lower homogenisation temperatures (153°C~320°C) and much lower salinities (1.0~6.0 wt per cent NaClequiv). Hydrogen isotopes (dD = -59‰~-41‰), analysed using fluid inclusion waters from quartz and calculated oxygen isotopes (d18OH2O = -5.47‰~4.00‰) for the equilibrated ore fluids, indicate that the ore-forming fluids may have been sourced from magma and mixed with groundwater in the late stages. Sulfide minerals have d34S values of 2.3‰~4.3‰, consistent with a magmatic-derived source for sulfur. Lead isotopes (206Pb/204Pb = 18.592~18.794, 207Pb/204Pb = 15.648~15.864, 208Pb/204Pb = 38.909~39.580) confirm that lead and, by inference, zinc were mainly derived from magmatic rocks, with subordinate contributions from sedimentary rocks.Various lines of evidence support that the formation of the Fozichong deposit has close genetic association with the granite porphyry intruded in the late Yanshanian period (106 Ma), and it can be classified as a magmatic hydrothermal type lead-zinc deposit. We propose that the Hesan and Guyi ore districts may represent the proximal and distal products of a magmatic – hydrothermal system respectively.CITATION:Fu, W, Zhang, H Q, Chai, M C, Yang, Q J, Chen, H Y and Wei, L M, 2015. Genesis of the large-sized Fozichong lead-zinc polymetallic deposit, Guangxi, south China – constraints from the sulfide mineralogy, fluid inclusions and isotope geochemistry , in Proceedings PACRIM 2015 Congress, pp 609–614 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By B, G Strobos, J P. Maree, N Smit

In mining and processing operations where minerals, high in pyrite and low in calcite/dolomite are processed, acid is generated, which needs to be neutralised. Ticor at Empangeni in South Africa (SA) produces rutile (TiO2), leucoxene (TiO2 plus iron compounds), titanium (Ti), zircon (Zi) and ilmenite (TiO2 plus iron compounds). Neutralisation is required in the processing plant where acid is leached into the wash water. This water needs to be treated to a quality suitable for re-use in the metallurgical process or to a higher quality to make it suitable for discharge into the Empangeni sewage system (SA). For re-use the water needs to be neutral and under-saturated with respect to gypsum while for discharge into the sewage system the sulfate concentration needs to be reduced to less than 500 mg/L (as SO4). Acid mine water is generally neutralised with lime. Disadvantages associated with lime are the costs and maintenance of the slaking equipment as well as hazards, associated with handling of the alkali. The cost of powdered limestone (CaCO3) in South Africa, a by-product, is 50 - 60 per cent cheaper than lime. A technology has been developed where limestone is used for neutralisation of acid mine water instead of lime. This development includes: Limestone handling and dosing system. A novel, robust system has been developed where waste CaCO3 from the paper industry is slurried to a constant density. A full-scale plant was constructed to evaluate its performance (Figure 4). The dosing system consists of an inclined slab onto which the limestone is stored and from where it is slurried into a make-up tank. The density of the slurry in the make-up tank is controlled via a loadcell that measures the weight of the tank (operated at constant volume) and activates/deactivates the spray of the recycle slurry onto the slab. Integrated limestone neutralisation/lime treatment process. In this process powdered CaCO3 is used for neutralisation and partial sulfate removal of acid leached from the coal washing plant. The sulfate concentration can be further reduced to below the saturation level of gypsum (ie 1200 mg/L) through gypsum crystallisation by means of lime treatment, resulting in metal precipitation (eg Fe3+ and Al3+). CO2- treatment for CaCO3 precipitation. The pH of the lime treated water can be adjusted to pH levels of 8.5 and lower using CO2. The CO2, generated during limestone neutralisation (Equation 2), can be captured and used in this stage of the process. The first two stages (limestone- and lime neutralisation) of this technology have been implemented on full-scale at Ticor to treat the effluent of the process. The constructed plant is 80 m3/hr and differs from coal processing plants by way of not containing Fe(II) and Fe(III) in the water. The CO2-treatment stage (Stage 3) will soon be implemented at IHM as part of a program to optimise the technology for maximum benefits.

Jan 1, 2003

The fluorspar deposits at Okorusu, Namibia are closely related to an alkaline igneous ring complex of late Cretaceous age (125¦7 Ma). The fluorite ores consist of relatively fine-grained purple replacement fluorite and subsequent coarser-grained purple and green vug-filling fluorite crystals. Homogenisation temperature measurements for 38 primary fluid inclusions shows that main stage purple to green fluorite crystals were deposited over a temperature range from 166¦C to 144¦C, and minor late yellow fluorite was deposited at lower temperatures from 132¦C to 128¦C. Homogenisation and freezing temperatures measured for 18 primary fluid inclusions shows that the fluorite-depositing fluids were less saline than Mississippi Valley-Type (MVT) ore fluids and overlap the lower temperature range of fluids that deposited epithermal ore deposits. Mining in three open pits (A, B and C) at Okorusu has gradually provided exposures which reveal that the fluorite orebodies have been emplaced primarily by the preferential replacement of carbonatites. Evidence for the replacement of carbonatite includes: replacement remnants of carbonatite within the fluorite ores; goethite pseudomorphs after the carbonatite minerals, pyroxene, pyrrhotite and magnetite, which are disseminated in the fluorite ores; andpartial replacement by fluorite of a large sill-like carbonatite body in the A pit. Electron microprobe analyses of minerals in unreplaced portions of the carbonatites show that their mineralogy consists of titaniferous magnetite, diopside pyroxene, apatite, biotite and calcite. Magnetite contains 6.97 per cent to 10.46 per cent TiO2, averages 8.44 per cent TiO2, and has an average V2O3 content of 0.35 per cent. At high magnifications under the scanning electron microscope (SEM), the magnetite shows abundant fine ulv÷spinel exsolution lamellae arranged in a cloth texture. Apatite contains moderately high fluorine contents that range from 3.21 to 5.0 per cent and average 4.2 per cent, and apatite crystals range in total rare earth oxides from 1.7 per cent to 2.61 per cent. Pyroxenes in the carbonatites are iron-rich diopside, and they contrast to pyroxenes in the fenites that are aegirine-augite. All of the microprobe analyses for mica crystals in the carbonatites give biotite compositions. Microscopic examination of fluorite concentrates from Okorusu provides mineralogical information important to the resolution of beneficiation problems. Fluorite ores that are related to carbonatites are typically accompanied by phosphorus benefication problems. The cause for the presence of phosphate in some of the Okorusu fluorite concentrates is a function of the presence of binary locked fluorite-apatite particles. The fluorite ores have also replaced marble locally in the A pit, especially along the A band in the B pit, and dominantly in the orebody proposed for the new C pit. Those ores are characterised by fine grain sizes, faint remnant bedding, lack of carbonatite mineral pseudomorphs and local presence of remnants of unreplaced marble. Concentrates derived from those fluorite ores are devoid of phosphorus, but commonly have elevated silica contents due the presence of free quartz. Carbonatite and marble were preferentially replaced by fluorite because the calcite was readily soluble in the presence of the fluorite-depositing fluids and the dissolution of calcite provided calcium for the formation of fluorite. 

Jan 1, 2008

The implementation of robust, reliable and accurate sampling systems is the key to the successful management of any mineral processing plant. The representative sampling of a mineral processing plant is the only way to determine what is coming into the plant, what is going out as fi nal product and what is going to tails. In plants with high gravity gold components, where high recovery effort gravity circuits are installed, the use of a gravity recoverable gold (GRG) sampling system can assist in the online monitoring of the performance of the circuit. The typical installation location would be in CIP or fl otation feed (ie cyclone overfl ow), downstream of the gravity circuit. A GRG sampling system generally consists of the following equipment: true proportional, continuous drive, linear cross cut sampler, secondary vezin sampler operated on a timer, a batch centrifugal concentrator, and sample dewatering module. The operating philosophy of the GRG sampling system is that the primary sampler operates on a continuous basis, generating a constant stream of truly representative sample. Consep's H&S drive system is unique in its ability to be able to operate in a continuous mode, therefore enabling a continuous stream of representative sample to be generated. The primary sample stream reports to the secondary sampler. The secondary sampler operates on an intermittent basis (nominally ten minute interval), resulting in a relatively small sample volume per shift. Normally the sample volume would be ten to 15 L per shift. The secondary sample rejects stream reports back to the batch centrifugal concentrator. The sample generated from the secondary sampler can be dewatered using a Consep H&S dewatering module. This device produces a final sample that consists of separate filter cake and filtrate. These are suitable for taking directly to the laboratory. The continuous stream of truly representative secondary sampler rejects is passed through an appropriately sized Knelson Concentrator, typically a KCMD7, KCCD10 or KCCD12 sized unit. This unit recovers any available GRG from the stream. The Knelson Concentrator is also purged of its gravity concentrate at the end of the shift. This sample, which is nominally around 1 - 2.5 kg of concentrate, is also taken to the laboratory. At the end of the shift the client will have a measure of the gravity recoverable gold content of the target slurry stream, as well as a true representative sample of the complete stream. Through the addition of a Knelson Concentrator to an otherwise typical sample station, it is possible to generate a true measure of the performance of your gravity circuit. This will take the guess work out of the daily variation in gravity circuit gold recovery, as the site knows whether the changes are due to gravity circuit equipment performance, or due to the natural variation of ore GRG contents. Maintenance planning can also be designed around the system, as the site will have a composite sample to measure the performance of the circuit, therefore indicating where performance has dropped and maintenance is needed. This is an ABSTRACT ONLY. No paper was prepared for this presentation.

Aug 1, 2010

An on-stream iron ore analyser has been developed in collaboration with Hamersley Iron Pty. Limited for determining the iron content of both lump (- 30 + 6 mm particle size) and fines (- 6 mm particle size) on conveyor belts. The analyser, which is called IRONSCAN, is based on pair production, and is now commercially available from Mineral Con- trol Instrumentation Limited (MCI) in Adelaide. It can be mounted under existing conveyor belts with minimal modifications to the conveyor struc- ture, and the presence of steel cables in the belt does not interfere once the analyser has been correctly calibrated. The analyser has been exten- sively tested on both lump and fines on the shiploading conveyor at Damp- ier, and typically the root mean square (r.m.s.) deviation between single IRONSCAN measurements and conventional chemical analyses is better than 0.5% Fe. It is currently being evaluated on - 150 mm ore from the primary crusher at Mount Tom Price, and initial results are encourag- ing. The principal advantage of IRONSCAN is that it provides rapid infor- mation on ore grades. But perhaps its greatest potential is at the primary crusher where conventional sampling and analysis is very expensive to Implement. at the University of Melbourne, and those of us who were his students had learnt of the application of physical chemistry to pyrometallurgical processing, pioneered by Chipman in the USA, Wagner in Germany, and Richardson in the UK. It was possible, by applying this theoretical insight to the equilibria between metal, speiss or Legierung, matte and slag phases, to find a practical and effective way to recover metal values in some residues which had been accumulating for many years at the NA, but which had defied all attempts to treat them to that date. There was also an opportunity to study the batch lead refining methods still in use at all lead refineries apart from Port Pirie, and to devise optimis- ing techniques which greatly improved the operations and effected considerable savings. Next the writer spent some six years alternating between the BHAS, Port Pirie, and Imperial Smelting at Avonmouth in the UK, concerned with lead or lead-zinc smelting, and the develop- ment of several further continuous lead refining processes, before returning to Australia as Section Leader, Process Development in the CSIRO Division of Chemical Engineering, Fisherman's Bend, Victoria. Metallurgical opportunities which arose during this last period included the problem of tin smelting which had developed over about a decade: the world's tin smelters had been accustomed to treating fairly high grade tin concentrates, con- sisting of almost pure cassiterite, with very little impurity-mostly quartz, limestone, iron oxides, and sundry other silicates. Most such concentrates had been produced from alluvial deposits, where nature had already done some of difficult part of the mineral processor's work-at who knows what recovery-so that he could now produce high grade concentrates at high recovery. The smelters were not really set up for the treatment of lower grade concentrates, such as could be made with reasonably high recoveries from rock mining. Thus they imposed such penalties on impurities and lower than desired tin grades, that whenever a mineral processor improved tin recovery at the expense of lower- ing grade, such an improvement entailed a lower financial return to the miner. There was clearly a need for improved understand- ing of tin smelting, (at that time shrouded in secrecy) and develop- ment of techniques better suited to the treatment of lower grade concentrates. As well as the practical development, a start was made with the computer modelling of the smelting process, with the obiect of optimising the process parameters.

Jan 1, 1988

By S Williams, N McBride

The aim of these analyses was to utilise the latest available production information for the Wandoo operation to determine the optimal blasting parameters, costing information and predicted results (fragmentation, muckpile shape and vibration). Much of the data used as input was made available from the information gathered during the excavation of the test pits during 1995. As with any æplanning stageÆ analyses, many assumptions were required to fill gaps in the available data. The calibration of computer blasting models was conducted using data from the last of the test pit blasts (this blast was carried out in material that closely resembled rock expected to constitute the bulk of the base case design pit). This calibration was refined using observation and experience based judgements to extend the accuracy of the predictions as far as possible. All the simulations were performed assuming that the blastholes will be wet (as instructed by BGM). This has consequently determined that the appropriate explosive for the simulations and the actual blasting will be a pumped emulsion/ANFO blend. The following blast design parameters were derived by determining a likely range of powder factor (from other similar scale gold mines) with a median value of 0.62 kg/m 3 being the powder factor arrived at through the field optimisation process conducted during the test pit excavation. The total swell/displacement percentage (volume after blast/volume before blast) largely determines the diggability of a well fragmented muckpile. Consequently where fragmentation is good any reduction of total swell will probably reduce diggabilty. Any reduction of diggability can and should be traded off against increased gold recovery. In most gold mines, diggabilty will be substantially compromised at the balance which produces the most profit. When these considerations are combined with the cost to drill and blast material, processing costs and the achievement of æacceptableÆ diggibility, the analysis becomes extremely complex and qualitative. Many trends are evident including:the relationship between powder factor (for each blast design) and maximum forward displacement (throw), see Figure 1; and the relationship between powder factor (for each blast design) and drill and blast cost per BCM, see Figure 2. The following blast designs are matched to each of three ore-tonnage alternatives (as supplied by BGM) (Table 1). They are all based on powder factor of 0.62 kg/BCM and are considered optimum from a mining æpoint of viewÆ. The costing of each design includes drilling, explosives and labour cost to load, stem and tie-in holes. Using the available rock data and relying heavily on the wall exposures in the test pit(s), it is the opinion of the author that between 20 per cent to 40 per cent of the final walls excavated in the Wandoo pit would be likely to have the angle between the dominant foliation and the wall plane that is well suited to presplitting and be cost-effectively served by presplit technique. The drilling cost for 125 mm blasthole is about $11.40 per drilled metre and the cost of 40 mm presplit explosive is about $140 per 25 kg (17 metre) case. This implies that the cost to drill and blast presplit on the above parameters would be about $10.90 per square metre of presplit face. The remaining wall area would be most cost-effectively delineated using modified production blasting techniques. This requires the use of modified parameters such as smaller hole diameters, smaller spacing/ burden, higher powder factor, free face firing, less rows per blast and longer delays. These altered blast parameters would usually be applied uniformly across the entire blast fired adjacent to the wall and this ætrimÆ blast would relieve burden away from the wall, into the pit. In simplest terms, this method relies upon maximised burden relief to minimise blast energy applied to the wall. It is only applicable where the material to be blasted is waste since the throw achieved is inconsistent with ore dilution control. The largest charge weight per hole for these analyses is 360 kg and the nearest domestic structure to the proposed Wandoo pit is about 6100 metres distant. From these parameters and assuming a worst case example of rock controlled site factor, the predicted ground vibration is 0.5 mm/sec that is about five per cent of the lower limit set down in AS 2187 part two (1993). This suggests that for the current location of neighbours, ground vibration will not be an issue for the Wandoo operation.

Jan 1, 1999

Historical exploration of the Ballarat East goldfield defined two primary quartz vein lode types. Tracking the intersection of these lodes with vertical lines of enrichment (or so-called æindicatorsÆ) was the basic practice for historical mining. This strategy proved highly successful in terms of identifying quartz veins associated with mineralisation. However, it provides little understanding of the timing or processes involved in the formation of these veins, or the associated emplacement of gold. Current underground mapping shows the Ballarat East gold deposit can be subdivided into four stages of vein formation. The earliest veins (V1 and V2) strike north-south and formed during bedding flexural slip and limb thrust fault propagation in parasitic chevron folds. V3 veins are subhorizontal and relate to further fold tightening involving a transition from east-west compression to north-south extension that initiated re-shear of bedded slip surfaces and additional strike-slip faults. Sporadic V4 veins overprint the shallow-dipping sections of V2 and V3 veins and are associated with weak north-south compression. The V4 veins mineralogy is distinguished by a high carbonate content and sphalerite-galena sulfide assemblage. Vein sampling indicates a significant increase in gold mineralisation where overprinting by the later deformation/veining has occurred. As a result of these observations, a new model is emerging that identifies the chronology, structural control and spatial distribution of respective quartz vein types. This is a major advance in terms of exploration targeting, resource modelling and mine planning.

Jan 1, 2008

The Kelian gold mine which was developed in East Kalimantan Indonesia in 1990 - 1992 is scheduled to complete mining and processing operations in 2004. This will have a major impact on the neighbouring communities who have benefited from the jobs, economic activity and infrastructure development which has been generated by the mine. Currently, there are no formal regulations or standards specifying the procedures for relinquishment of mining leases in Indonesia. Furthermore, a move towards regional autonomy, providing greater authority and responsibility to local (regional) areas, has recently been implemented in Indonesia and limited capacity exists in the new regional governments. Consequently, in October 2000, Kelian Equatorial Mining (KEM) initiated a partnership with the local community and government to explore sustainable post-closure options for the mine site and community development programs. The Kelian mine closure strategy seeks full involvement of all stakeholders through the Kelian Mine Closure Steering Committee (MCSC) in the development of sustainable solutions which will enable communities to secure long-term benefits and minimise post-closure risks from the KEM operations. This organisation, jointly chaired by the Head (Bupati) of the regional West Kutai government and the KEM President Director, with representatives from the local communities, governments and NGOs, has developed a Charter, a website and evaluation criteria to ensure accountability and transparency. There are four technical working groups, consisting of representatives from the mine, local community leaders, NGOs, Universities, Local, Provincial and Central Government Departments, which report to the Steering Committee. These working groups have researched, developed and recommended sustainable options to the Steering Committee. The MCSC has met quarterly to examine options in accordance with the criteria set out in the Charter and has endorsed sustainable solutions which have support from Government, Community and the mine. This paper describes the closure risks, sustainable outcomes derived through the Kelian mine closure steering committee process and outlines the methodologies used to develop and endorse sustainable solutions in a society with limited capacity undergoing enormous change and uncertainty.

Jan 1, 2003

Kalgoorlie Consolidated Gold Mines Pty Ltd is currently developing the 'Super Pit' gold mine in the mining area known as the Golden Mile adjacent to the city of KalgoorlieBoulder, Western Australia. The presence of numerous abandoned mine workings and complex structural geology has required considerable geotechnical input into the determination of the optimum pit slope geometries for both interim and ultimate pit slopes. Slope design is based on detailed site investigation and stability analysis which is balanced with historical operational experience. This paper discusses the process of determining the optimum pit slope angles for each of the stages of the west wall of the 'Super Pit'. The risks associated with slope instability are discussed for each stage.

Jan 1, 1994

In the current climate, there is a real need to bridge the gap between theory and the real world mining considerations, and develop viable, cost-effective, high performance thickeners. With a greater need to extract profits from both difficult-to-process ores and lower grade orebodies, coupled with the necessity to produce 'greener', less water intensive technologies, suppliers need to take current thickener designs to the next level and into the 21st century. The complexity of 'getting it right' within a thickenerÆs feedwell, the 'nerve centre' of the thickener, is no small task. Delivering dilution water and mixing this water with incoming feed slurry, addition of flocculant, maximising flocculant-slurry interaction to build aggregate size, minimising unabsorbed flocculant percentage, volume average of solids volume fraction, momentum dissipation ratio, dilution recycle ratio, volume average shear, maximum shear rate at exit, aggregate size on exit, uniform discharge profile and more ù all of these need to occur in the right order and in the right proportions within the feedwell. This paper discusses the genesis and evolution of a new feedwell design, the first major innovation in the thickening industry in over 15 years.

Jan 1, 2008

By G W. Scott, R C. Johnson

Hypogene alteration zones have been described as a precursor to high-grade haematite deposits in Australia, Brazil and elsewhere. This alteration is described as being below or distal and is typically magnetite-carbonate-silicates reflecting Mg - Fe metasomatism. This paper describes, without genetic implication, the mineral zonation and possible structural control on mineralogic variation within the Tilden Mine, a concentrating grade haematite deposit in Michigan, USA. In contrast to the high-grade deposits, these variations are not peripheral to the orebodies but are the ore. The deposit occurs within the Negaunee Iron Formation, along the southern margin of the Paleoproterozoic Marquette Range Supergroup basin. The regional structure is a fault-bounded west plunging syncline within the crustal scale Great Lakes Tectonic Zone, which forms the boundary between Archean granite-greenstone and gneissic terranes. Local structure consists of second-order anticlines and synclines with variable northwest and southwest plunges. The interaction of sedimentation and diagenesis within growth fault controlled basins, along with a possible metamorphic and/or hydrothermal overprint has resulted in a complex series of ore types. For modelling purposes, the deposit is divided into geologic domains based on both lithology and metallurgical response in the laboratory and in the plant. Mineralogic variation is recognised within individual mineral grains; at blast pattern (10 - 15 m) and development drill hole (100 m) scales.

Jan 1, 2007

By A Hekmat, R Castro, A Casali, R Gómez

Block caving is the most economic underground methods for excavating massive orebodies, due to the high productivity and low production costs. The success of block caving operations depends on the fragmentation and draw control as large blocks decrease the equipment efficiency, inhibit the material flow and may lead to expensive secondary blasting. Even though ore handling system design, as well as overall economic results, both critically rely on secondary fragmentation, this parameter continues to be one of the least understood issues in the caving operations.This research focuses on the experimental study of secondary fragmentation, considering the impact of vertical pressures and material flow. Experiments using a load-haul-dump extraction system were conducted under laboratory conditions to quantify the influence of pressure and particle size on secondary fragmentation. Results demonstrate that increasing the vertical pressure (simulating deeper conditions) leads to higher fragmentation (smaller particle size) and greater fines generation during draw. The experimental results were applied to calibrate the developed mathematical model based on kinetic matrix. The acceptable accordance between the comminution model results and the reality showed that this method is convenient in predicting the secondary fragmentation in block caving.CITATION:Castro, R, Gómez, R, Casali, A and Hekmat, A, 2016. Experimental and comminution model framework for secondary fragmentation prediction in block caving, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 175–182 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016