Search Documents

By Medhurst TP, Trueman R, Hutchinson IN

A breaker line support (BLS) monitoring system, BLSmon, has been designed and constructed by the CSIRO and installed and commissioned at Laleham No.] Colliery, Queensland. This system was designed to record hydraulic leg pressure and canopy position measurements and relay these, in real time, to the surface. The system has shown itself to be capable of operating on the BLSs without any adverse affect on production. Analysis of the results of the monitoring exercise has shown that rate of change of leg pressures on the BLSs could be used as an aid in the prediction of adverse mining conditions. Under favourable mining conditions the supports were observed to initially unload from the set pressure, this unloading reduced with time and by the end of a typical lift cycle had either ceased or reversed slightly. This behaviour was considered to be due to one of four possible causes, these being; the compaction of floor debris, and/or compaction of the floor, and/or crushing of the roof and /or support creep. The actual cause can only be determined through detailed monitoring of both roof and support convergence. However observational data would suggest that compaction of debris and softened floor material beneath the supports was the most likely cause. The few positive loading rates recorded under these conditions were of short duration and occurred towards the end of individual lifts. Where mining conditions were unfavourable the negative rates of change of pressure, unloading of the support, were reduced throughout a lift, in both duration and magnitude, when compared with favourable mining conditions. Over the same period the positive rates of change were observed to be greater. The rate of change of loading and convergence can be utilised to identify the onset of instability in the lift area. However, before this facility can be utilised by the mine for the reliable prediction of instability more monitored data and sophisticated processing techniques are required.

Jan 1, 1992

The An Shan iron ore deposit is the biggest low-grade oxidised iron deposit in China. Over the past ten years, about 120 SLon verticalring-pulsating high gradient magnetic separators units have been installed in An Shan to process oxidised iron ore. This paper describes how several plants have upgraded their old technologies to new technologies with SLon magnetic separators as the key equipment for controlling tails grades, including using reverse flotation as the key technology for iron concentrate cleaning, These plants have been modernised with beneficial results at low cost.

Jan 1, 2009

By Barber C, Buselli G

Detailed monitoring of point sources of groundwater pollution is expensive due to the high cost of drilling monitoring boreholes. Whether groundwater pollution is due to mining, industrial or domestic waste disposal, a universal difficulty when monitoring groundwater contamination is the placement of boreholes to adequately define the extent of the pollution plume. This paper reports groundwater 'resistivity variations determined from transient electromagnetic soundings at a domestic waste disposal site north of Perth in Western Australia. Together with available hydrogeological and water quality data, the geophysics provides a broad "plume scale" picture of groundwater contamination. A simple three dimensional model of plume development, which takes account of the dimensions of the wastes, has also been developed and shows good agreement with the spread of contamination indicated by the geophysics for relatively small values of the dispersivities. Better estimates of these parameters are still required. The work indicates that a combination of geophysics and modelling with ground-truth data from groundwater quality monitoring of boreholes is required to avoid difficulties in interpretation of data and to better define the extent and migration of pollution in Groundwater.

Jan 1, 1988

By Artieda JJ, Catalina JC

- The aim of this paper is to analyse the possibilities of applying signal processing and artificial vision techniques to the ore sorting problem. In order to overcome the limitations imposed by the classical approach to the problem, which essentialy cons

Jan 1, 1985

By M Yvon, S Parkes, K P. Galvin, P Wang

Mineral liberation is critical to maximise the grade and recovery of nickel, however this objective is challenged considerably by the poor flotation kinetics, especially that of ultrafine particles (Kelebek and Tukel, 2018; Multani and Waters, 2019). High recoveries demand long cell residence times and hence a large flotation capital expenditure (Wills and Finch, 2016). However, this leads to excessive entrainment of gangue minerals, thus negating efforts to depress its recovery. This study aimed to investigate new hydrodynamic approaches to improve nickel flotation, focusing primarily on unrecovered nickel from a Western Australian tailings stream. Mechanical cell flotation experiments were conducted to understand the flotation kinetics, covering different size ranges. A novel Reflux Flotation Cell (RFC) was also used to improve the nickel recovery and reject the silicates. Future work aimed at applying the RFC to different size portions is also outlined.

Aug 24, 2022

By I T. Cameron

The commercial production of copper metal involves a sequence of purification stages. One step of this process eliminates bulk quantities of iron and sulphur from matte Cu2S(FeS to produce blister containing 95.5 per cent copper. This task is traditionally performed in the Pierce-Smith converter, a cylindrical vessel in widespread use throughout the copper industry. Typically, multiple Pierce-Smith converters are arranged along an aisle, simplifying material transfer from vessel to vessel. Materials are moved through the aisle in pots and boats, using overhead cranes. In terms of the overall process, the converter aisle represents a critical processing unitùit contributes significantly to the value added nature of the metal. The aisle is subject to significant process disturbances. Thus, improvements in the operationÆs modes and conditions have a direct impact on process profitability. As with any commercial operation, improvements are always sought to increase process performance. The general approach involves process modelling, followed by an application of control and optimisation theory to this model. The results of such a study are then applied to the real process, leading to improved performance.

Jan 1, 1998

By Hunsaker R. D

The description, characteristics, advantages and application of a new bulk explosive for medium to large diameter dry blasthole conditions is described. A brief outline of the delivery system for the product is also included. This explosive has been designed to provide an alternative to ANFO, currently the most common bulk dry hole product available to the mining and quarrying industry. The selection of the optimum explosive for any blasting operation is of prime importance. It is a major factor contributing to the production of the desired results in terms of muckpile fragmentation, shape and diggability. The optimum explosive can be defined as the most cost-effective in producing satisfactory breakage and displacement of the material. ANFO satisfies this prerequisite for a significant proportion of dry hole applications. This unique, low density and low velocity of detonation explosive has been developed to provide the industry with a cost competitive alternative to ANFO. Typical loading or average inhole densities nominally range between 0.40 g/cc to 0.70 g/cc, depending on the application. Characteristics of this explosive allow for specific and common applications in open cut coal and metalliferous operations. These include ore/waste control operations, prestripping and presplitting applications, sites confronting cap rock problems, and large hole diameter quarries.

Jan 1, 1995

By P Wahyono, H Vega, S Riza, P Vergara, P Gonzalez-Carbonell

PT Freeport Indonesia (PTFI), operating in the Ertsberg Mining District in the Province of Papua, is developing the Grasberg Block Cave copper-gold mine. The site aims to output 160 000 t/d and will be located underneath the current Grasberg Open Pit. Initial studies of the potential to develop a block cave mine in the Grasberg orebody have revealed that the mine will require significant volumes of air. The Grasberg Block Cave (GBC) project requires four primary fans (3750 kW each) to support production at full capacity.Fan #1 commissioning was accomplished successfully on 9 February 2012. However, Fan #2 chamber, which is separated by a 20 m pillar, had not been completed. The main challenge was Fan #2 chamber still needed to be benched. The risk of damage to the critical infrastructure in Fan #1 chamber, including ground support, cracks in pedestals, and misalignment in the impeller shaft were considered. The challenges were blasting the bench without damaging the surrounding infrastructure, completing the work safely and meeting the schedule. This was achieved with the engineering control methodology. This paper summarises the benching process of Fan #2 chamber and its impact upon Fan #1.CITATION:Vega, H, Riza, S, Gonzalez-Carbonell, P, Wahyono, P and Vergara, P, 2013. Excavating an underground primary fan chamber that is adjacent to a fully operational primary fan in PT Freeport Indonesia's Grasberg Block Cave Mine, in Proceedings The Australian Mine Ventilation Conference , pp 115-122 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By Quast K. B

Samples of limestone and micaceous hematite have been ground in a laboratory batch mill using equal weights of either rods or balls. Values of the Schuhmann distribution modulus, a, have been shown to depend on grind time and do not remain constant as often reported. The linear reduction in a with grind time was attributed to a change in grinding mechanisms with time. The product sizing from ball milling limestone showed a bimodal distribution, but rod milling produced a unimodal size distribution. The product sizing from milling micaceous hematite was difficult to interpret due to the major influence of the shape factor on the transition from screen sizing to cyclosizing.

Jan 1, 1995

From August 1962 to June 1976 Peko Mines Ltd. produced Gold Bullion at the Peko Control Mill using 18x24 Denver Mineral Jigs and strake tables. Gold ores treated during this period were obtained from Orlando, Juno and Ivanhoe Mines and from the Warrego Mine after 1974, all in the Tennant Creek Area of the Northern Territory. With the downturn in copper prices Warrego Copper ore mining ceased and the copper Smelter closed down in February 1974, Warrego gold ore continued to be treated in the Peko Concentrator.

Jan 1, 1978

By S Agdaca

Leightons is the sole contractor at the Wahana Coal Mine Project (part of the Bayan Group), a multi-seam thermal deposit consisting of 13 coal seams with thicknesses ranging from 20 cm to 500 cm. The average dip of the deposit is 18 - 20°. However the deposit is heavily faulted in certain domains with anticlinal and synclinal structures present causing seams to dip up to 90°. Average thickness of coal inter-burdens range from less than 2 to 12 m. The minimum coal thickness being mined is 20 cm. Coal production is direct mine mouth feed and there is no coal processing plant currently used.Conventional blasting between the highly variable coal horizons in the early phases of the mine life was suboptimal from a production perspective. Drilling short holes with a reduced drill pattern, and on occasions with sloping benches, resulted in low drilling and explosives loading efficiency.A high frequency of small size blasts fired up to two times daily was required with each blast consisting of four up to five small blast areas. Each blast averaged approximately 36 000 bcm thus causing a low utilisation rate of the mining fleet from frequent blast delays and the inability to deploy larger Liebherr 9350 excavators on bench. It was identified that increasing the production targets required a more efficient drilling and blasting process. Furthermore, due to the highly variable nature of the deposit, the existing coal model was determined to not be able to accurately predict the coal seam location prior to blasthole drilling.In August 2009, Leighton Contractors Indonesia and Orica Mining Services with the full support of the Wahana team, initiated through seam blasting trials using electronic blasting systems. Further trials were conducted in November 2009. Trial evaluations indicated that the benefits from decreased lost time events due to blasting, an increased vertical advance rate per blast, and increased overall blast size could be attained while not damaging or diluting coal.Full-scale?through seam blasting has been ongoing since February 2010 for the upper eight coal seams to extract coal seam thicknesses ranging from 20 - 100 cm. This paper will discuss the parameters of the through seam blasting process in Wahana and the resulting benefits to the overall mine production.

Nov 8, 2011

By Hutchings SG, Skimmings T

This paper describes the results of the field application tests at Miike Colliery on the integrated automatization of the longwall mining system for medium thick coal seam. The purpose of the research is to develop an automatic longwall mining system which can be controlled accurately from outside of the face, and the ultimate goal is an eliminate of men from the face. Presently, the field test is being conducted in Yotsuyama mine following to a success in the performance test on surface. Remote Batch Control System for shield supports has been adapted to operate all supports from the control panel located at the entrance of the face. Remote monitoring and control system of the drum shearer has also been tested. The system makes it possible to operate the shearer either at the main gate or full automatic. Productivity and safety will be substantially improved as those systems enable to eliminate all workers from the face under the severe working conditions with high ground pressure and hot and humid atmosphere due to increasing mining depth. So far, we have been satisfied with the results of the field test and those system will be an effective countermeasure to operate the face with a high risk of rock-burst.

Jan 1, 1987

By Pina P, Pereira MJ

The increasing exhaustion of raw materials entails the exploitation of poorer orebodies where the target mineral occurs frequently in a very fine dissemination. Consequently it is necessary to grind more and more fine to achieve an adequate mineral liberation. In other words, it is of fundamental importance to know what size one should grind in order to avoid the following detrimental situations: 1. Excessive grinding - giving rise to the generation of ultra-fine slime particles which may be lost in the ulterior concentration process and simultaneously leading to higher energy consumption. 2. Incomplete grinding - giving rise to insufficient liberation and consequently leading to considerable losses of the valuable components in the tailings. Although this issue constitutes one of the most important steps in mineral processing, little research has been done compared to other processes, mainly due to the fastidious experimental work required. This paper describes a complete and integrated system of image analysis, where some algorithms to determine automatically the degree of li beration, for different levels of grinding, are proposed. These algorithms, mainly based on mathematical morphology theory were tested with images obtained from polished sections of different grain size fractions. Cases studies on a complex sulphide ore from an important copper and tin deposit located in the South of Portugal are discussed. Samples of the unbroken ore are also studied by image analysis to predict the degree of liberation obtained according to the fineness of grinding.

Jan 1, 1993

By H Kusumi, A Nishio, K D. Halim, Y Yun

In Japan, evaluation of rock mass is crucial in mountain tunnels that are constructed using the NATM (New Austrian Tunneling Method) to determine the support pattern that in turns determine the final support structure of the tunnel. The current evaluation method is highly dependent on the observations of on-site expert engineers that grades the rock mass in four levels across nine criteria: A. Condition of tunnel face. B. Condition of excavated surface. C. Compressive rock strength. D. Weathering. E. Spacing of discontinuity. F. Condition of discontinuity. G. Orientation of discontinuity. H. Spring water. I. Water degradation. However, in recent years, the number of said experts are decreasing rapidly due to labour shortage caused mainly by an aging population and declining birth rates. This is one of the biggest challenges that the construction sector currently faces, and this may affect the efficiency of tunnel construction projects in the future. Thus, this study proposes the implementation of a deep learning tool called the convolutional neural network (CNN) to quantitatively evaluate rock fractures on tunnel face. In addition, Gradient-weighted Class Activation Mapping (Grad-CAM) is applied to visualise CNN, as well as verify the applicability of CNN to the evaluation of rock fractures. In other words, by creating heat maps of tunnel face images, CNN is utilised to evaluate rock mass in categories that are associated with discontinuities. The CNN model is most accurate when six convolution layers, four pooling layers, and three dense layers are used. This yields an accuracy of 75.0~88.0 per cent. Thus, the CNN model is verified to be feasible method to evaluate rock fractures.

Nov 29, 2022

By N Donnellan

The Palaeoproterozoic Warramunga Formation is notable as the host to the enigmatic, so-called 'Tennant Creek style' mineralisation. These polymetallic (but mainly Au-Cu-Bi) ore deposits typically have a close spatial association with massive ironstone bodies, and frequently also with banded ironstone, known locally as 'haematite shale'. The Warramunga Formation is a polydeformed, turbiditic succession. Partial, or complete Bouma sequences variously comprising lithic arenite, wacke, siltstone, and mudstone constitute a classic flysch sequence deposited as a proximal (sandstone lithofacies) to distal (siltstone lithofacies) fan association. The Warramunga Formation has a substantial component of volcanic detritus and has generally been attributed to an essentially contemporaneous volcanic provenance. However, lithostratigraphic revision (Donnellan, Hussey and Morrison, in press) apparently precludes outcropping volcanic rocks of the Tennant Creek Block, or indeed Inlier, as the source of detritus. Warramunga Formation geochemistry indicates rapid derivation from a fractionated, predominately felsic igneous source (Palaeoproterozoic upper crust) with a minimum of chemical weathering; together with an admixture of mafic material. Warramunga Formation geochemistry cannot, however, be reconciled with that of the Bemborough Formation, which is here taken to be representative of Flynn Subgroup felsic volcanic rocks. Similarly, the Warramunga Formation is geochemically distinct from Flynn Subgroup sedimentary rocks. Geochemistry of the banded ironstone is consistent with its interpretation as Dine-grained turbidites.

Jan 1, 1994

By K Tungpalan, E Wightman, M Edraki, E Manlapig, L Keeney

The depletion of easily mined high-grade ore bodies resulted in the industry having to exploit lower grade, complex resources (Albanese and McGagh, 2011; Darling, 2011; Randolph, 2011). The trend is now towards mining and processing of low-grade and complex ores (Darling, 2011; Yingling, 1990). Variable geological and mineralogical characteristics, and complex mineralogy and texture can result in large variations in metallurgical response and also cause challenges in processing. (Carson, 1995; Lorenzen and Barnard, 2011; Yingling, 1990). Variability and the complex nature of ores are fundamental sources of risk that often cause the greatest economic impact (Dusci et al., 2007; Williams and Richardson, 2004). Hence it is important to effectively characterise these types of ore bodies and assess their processing performance (ie recovery, grade). To enable this, there is a need for the following: (i) characterisation of geological, mineralogical and metallurgical variability in the ore body; (ii) effective selection of drill core with characteristics that represent the range of ores in the entire ore body. CITATION: Tungpalan, K, Manlapig, E, Keeney, L, Wightman, E and Edraki, M, 2018. A systematic approach of sample selection to predict processing performance of an ore body, in Proceedings Complex Orebodies Conference 2018, pp 67–70 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By A Mokhtari, S Gatehouse, N Rutherford

Geochemical exploration continues to play a significant role in new mineral discoveries inAustralia and elsewhere, including terrains where mineralisation is buried or otherwise obscured by regolith cover of various types. Transported regolith commonly restricts the migration of trace elements to surface, especially in arid terrains, presenting a range of problems for traditional geochemical exploration methods that employ surface samples. Regions dominated by transported cover include the northern parts of the Tasmanides in eastern Australia and the Yilgarn Craton which are variably covered by thick alluvium and Mesozoic to Cainozoic sedimentary rocks (Anand and Paine, 2002). An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By D Mather, H R. Asche

"In the civil tunnelling field, the use of tunnel boring machines (TBM) has now overtaken the use of conventional excavation methods (drill and blast / roadheader). This is due to a number of reasons, including the increasing availability and reliability of TBMs, the ability to deal with a wider range of face conditions, and the reduced excavation cost that TBMs can bring.Mining companies have spearheaded the advances in shaft boring by mechanised means, both in blind and raise boring. However, mining companies have been slower to adopt mechanised tunnelling.When contrasted with a conventional mining contract, there are good reasons why TBMs in mining applications are relatively rare. A conventional decline contract may have very little geotechnical information. The decline alignment can be subject to change as the tunnelling progresses. The infrastructure requirements are less for a conventional decline, and the sunk cost prior to excavation commencing is lower. Contract documents can be very simple.The history of TBM use in mining is reviewed and lessons are described. From the case histories and lessons learnt, the paper identifies ways that mining companies can maximise the potential benefit of TBM technology.We believe that despite the additional requirements for TBM declines, the cost and time advantage to mining companies is very attractive. The challenge is to recognise and to meet the requirements for success in a TBM drive to achieve the advantages of: faster advance rates reduced rock damage/overbreak reduced support requirements uniform muck characteristics greater personnel safety.From the case histories and lessons learnt, the paper identifies ways that mining companies can maximise the potential benefit of TBM technology.CITATION:Asche, H R and Mather, D, 2014. Use of ?tunnel boring machines in the mine environment, in Proceedings 15th Australasian Tunnelling Conference 2014, pp 655–662 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 17, 2014

Hydraulic backfill is generally retained in slopes using permeable barricades. Mitchell et a! (1975), Mitchell (1992) and Grice (1989) have shown that under normal drainage conditions, barricades experience low levels of loading. Cowling et a! (1988) have also shown that barricades are susceptible to piping failures if excess water has ponded on the upper backfill surface and if leakage of backfill from the barricades has occurred. During 1997, six hydraulic backfill barricades failed in four different Australian mines. Fortunately, in each case, the quantity of backfill slurry released was small, and no injuries to personnel nor damage occurred. Detailed investigation of two of the incidents showed that the primary cause of failure could be attributed to the delivery of excess quantities of transport water from the low-density slurry. For each of the incidents investigated there was evidence of the development of piping failures, which resulted in hydrostatic loading conditions on the barricades from the ponded water on the upper backfill surface. The circular failure surfaces in the barricades were characteristic of the application of point loading Conditions.

Jan 1, 1998

By S Hawker, M Gibbs, A Craven

Current climate change projections suggest both an increase in the intensity of significant rainfall events and an increase in the variability of rainfall in some regions of Australia. It is necessary for mine site owners and operators to understand the effects that this potential shift in climate may have on their operations. The ability to maintain compliance with discharge regulations and operational security for those sites that rely on surface water run-off harvesting may be negatively impacted if some current climate change projections are realised. Although current regulations require the preparation of water management plans, these are generally developed using historical climate records for the site in question and as such do not give any indication of a siteÆs resilience to the influences of climate change.This study compares design and operational considerations for a case study mine site using historical rainfall records and modified records representing climate change projections. The future climate models are invariably broad scale and are limited in their capacity to be downscaled to a reasonable resolution for developing a site water balance. Instead the local historical data set has been modified to concentrate precipitation to peak periods and propagated through the model. The study looks at the siteÆs response to the potential changes in climate.It is shown that if current climate change projections are realised, this will have a significant effect on both the necessary size of designed surface water infrastructure and operational considerations on-site. A discussion is presented on the potential risks that climate change presents to mine sites and the range of options that could be considered to mitigate these risks. Depending on a number of factors, including location and risk profile of the owner/operator, resilience to climate change can be addressed as either a capital or operational expenditure (CAPEX/OPEX).CITATION:Craven, A, Hawker, S and Gibbs, M, 2013. Site water balance response to variable climatic conditions, in Proceedings Water in Mining 2013 , pp 211-216 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013