Search Documents

By T Muzondo, C Prins, D De Vaux, R Schouwstra

The Mogalakwena Platinum Mine in the northern limb of the Bushveld Complex is Anglo American PlatinumÆs only open cast operation exploiting the Platreef. The Platreef, which extends along the basal contact of the Bushveld Complex, is geologically and mineralogically a much more complex orebody than the Merensky and UG-2 reefs. Changes in the footwall and the genesis of the Platreef translate into a number of rock types being present. These rock types vary in hardness and recovery potential and present challenges to metallurgical staff trying to optimise the concentrator. A true understanding of the implications of treating these rock types is required if the maximum value from this orebody is to be obtained.In order to more accurately forecast production and incorporate ore variation in the mine plan and comminution and flotation circuits, a geometallurgical approach to managing the operation has been used and is being further developed.CITATION:Schouwstra, R, De Vaux, D, Muzondo, T and Prins, C, 2013. A geometallurgical approach at Anglo American PlatinumÆs Mogalakwena Operation, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 85-92 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By Hare S. M, Lumsdaine I, O&apos

Converter slag assaying 3.7 per cent Cu is produced by Mount Isa copper smelter at a rate of up to 180 000 tonnes per annum.Priority is given to the processing of ore, however concentrator capacity periodically exceeds that of the mine and the opportunity is taken to treat converter slag. It is processed in batch campaigns, typically through the Copper Concentrator, but the Hilton Concentrator has also been used. Slag and ore are kept as separate as possible, since each has an adverse effect on the flotation performance of the other.

Jan 1, 1993

By L Klemettinen, J Biswas, W Malan, D Sukhomlinov, D Lindberg

In order to mitigate the effects of climate change, our society must be able to drastically reduce its CO2 emissions. As the metallurgical industry is a considerable contributor to these emissions, new greener technologies must be invented and developed. One option could be the direct production of metals from oxides using renewable electricity. The aim of this study was to investigate the possibility of using high-temperature molten oxide electrolysis (MOE) for iron and ferrochrome production. FactSage™, ver 8.2 (by Thermfact Ltd and GTT-Technologies) was utilised for estimating a feasible equilibrium electrolyte composition, and the experiments were conducted at 1550–1580°C in conical alumina crucibles with iridium wire as the cathode and platinum wire as the anode. The sources of iron and chromium were either pure FeO powder or industrial chromite pellets. Voltage was applied to the electrolysis cell for 6 hrs and the resulting current was measured, along with oxygen concentration in the off-gas line. The electrolyte comprised of SiO2, Al2O3, MgO and CaO. First, the effect of FeO concentration on iron reduction efficiency was investigated using only pure oxide powders as starting materials. The results indicated that 10 wt per cent FeO mixed with the electrolyte resulted in more efficient iron reduction compared to 20 wt per cent. In further experiments, industrial chromite pellets were ground and mixed with the CaO-free electrolyte. Iron and chromium reduction efficiencies were higher when approximately 19 wt per cent of the total sample mass consisted of pellets compared to increasing the pellet amount to 37 wt per cent. Generally, the chromium solubility in the liquid electrolyte was relatively low, and most of the chromium was confined to the spinel solid solution, from where its dissolution to the liquid electrolyte was very slow, resulting in slow reduction kinetics. For larger scale applications, economically more viable electrode materials should be investigated.

Jun 19, 2024

By R A. Pax

Electrostatic separation is a core requirement for the beneficiation of mineral sands suites to provide valuable product. Although the basis of electrostatic separation has been understood for some time, the details required to be able to calculate the metallurgical performance of a separator has not previously been achieved from a mechanistic perspective. Empirical models have had some success but require extensive test work. Traditionally, performance of an electrostatic separator is determined by careful experimental work using the target mineral suite. Although electrostatic separation was invented at the end of the 19th century, very little modification of the basic equipment occurred until relatively recently, with the addition of a plate electrode to aid separation. Previously, the author has presented results, calculated using finite element modelling (FEM), of the electric fields present in an electrostatic separator in various configurations. This paper will present some new mathematical modelling work, which uses the FEM determined electric field configurations but also incorporates some fundamental physical processes that provide insight as to the limitations and opportunities for this important separation technique.

Oct 5, 2011

By C Hamilton

Stawell Gold Mines (SGM) is an underground mining operation located in Victoria, Australia. The mining method employed is long hole retreat stoping, utilising up and downholes and artificial concrete pillars. Stawell is currently mining the Golden Gift and Magdala orebodies.Access to the Magdala and Golden Gift deposits is via 6.0 m wide by 5.5 m high declines developed at a gradient of one in eight to one in seven from the surface to a depth of 1500 m, with a planned depth of 1650 m. From the declines, cross cutting drives are developed to intersect the orebodies. Orebodies in the Gift system are discrete lodes which are generally mined from a bottom up centre retreat to minimise geotechnical stresses.Ore development fronts are currently located between 1000 m and 1500 m below surface, with all ore being hauled to the surface using a fleet of 60 tonne underground trucks. With the use of conventional pyrotechnic long period (LP) delays, broken rock of combined ore and waste is thrown 10 m from the face and the materials hauled to the surface. The majority of the mullock from development is consumed in the underground as backfill.With the use of Orica Mining Services eDev™ Electronic Blasting System for Tunnelling, the waste is thrown up to 40 m from the face, while majority of the ore is left 5 - 10 m from the face, effectively segregating ore and waste. This enables significant recovery of gold values with minimal loss and significantly reduced dilution. By using this technique in ore drives with a 30:70 waste to ore ratio, SGM is able to haul 24 000 tonnes less mullock to the surface annually. Resue mining is applied to narrow vein headings and gives a 40 per cent grade increase at the faces as well as increasing the economic footprint of development. This will also contribute to an improved grade profile for the year from 3.98 - 4.16 g/t Au and allow extra capacity for ore haulage from stoping and for milling.This paper describes the application and the successful blast outcomes achieved using the eDev™ Electronic Blasting Systems for resue mining at SGM. Results to date, since commencement in March 2010, have been achieving significant benefits in terms of ore grade as confirmed by geologists grab sample grades. Face advance have also shown improvement with better breakage of perimeter holes giving improved face profile. These benefits are delivering increased productivity and safety performance when compared to other resue firing techniques.

Mar 21, 2011

The West Fork project is located in Reynolds County, Missouri, in the mineralized zone referred to as the Viburnum Trend. The West Fork orebody has a calculated ore re- serve of 13 600 000 tonne (15 000 000 st) con- taining 5.5 per cent lead, 1.2 per cent zinc, and recoverable values of copper and silver. A total of 64 600 tonne (71 200 st) of lead concentrate and 11 300 tonne (12 500 st) of zinc concentrate will be produced annually. The mill was designed to operate at an average capacity of 3450 tonne/day (3800 st/day), based on a 95 per cent availability factor. The mill will operate 24 hours a day, 5 days a week, with maintenance performed, as needed, on weekends. The mine will operate on an identical schedule; but the underground, pri- mary crushing will operate on a six hour/shift, three shift/day schedule. The 1.07m x 1.22m (42in x 48in) jaw crusher will produce a minus 20cm (8 in) material at an average rate of 191 tonne/h (211 st/h). The jaw crusher has almost twice the throughput capacity required, but the decision to install that size of crusher was based on the need to handle over sized rock in the ore.The coarse crushed ore will discharge into a 180 tonne (200 st) skip pocket, which will allow up to a one hour surge capacity prior to hoisting. Hoisted ore will discharge into a 900 tonne (1000 st) storage bin located adjacent to the headframe. The skip pocket and coarse ore silo comprise the total ore storage capacity. The concept of having no intermediate fine ore storage between the secondary crushing and grinding sections was borrowed from the Brushy Creek Mill of St. Joe Minerals, which operates adjacent to the West Fork property. Integration of the secondary crushing and grinding circuits has worked ' successfully for years at the Brushy Creek Mill. The most obvious advantage to eliminating the intermediate fine ore storage is'capital expen- diture savings. The capital expenditure savings include the cost of silos, feeders, and the cost of additional conveyor length and eleva- tion. Savings in operating costs will also be gained, particularly in reduced maintenance costs. Other factors which influenced the decision to eliminate fine ore storage were the simplicity of the secondary crushing sec- tion and the limited area available for con struction of the facility

Jan 1, 1978

By P Hayes, D Fadhlurrahman

Molten slags, fluxes and salts play key roles in a wide range of the high temperature industrial process applications, including metals production, refining and recycling, metal manufacturing processes, electrochemical metal production cells, batteries, and efficient heat transfer media. Recognising the importance and significance of fundamental scientific knowledge of these systems, the International MOLTEN Conference series was established to provide a forum to bring together leading academic researchers and industrial engineers to present and discuss the latest scientific ideas and findings, and their application in their respective fields. This article presents an analysis of the research carried out in this field over time in terms of the number of journal articles, fields and slag systems studied and geographical origin of the research.

Jun 19, 2024

By J Gould, T Elkington

Mine operation strategies are commonly optimised with a net present value (NPV) maximisation objective. There are well known properties of a typical mining project optimised for NPV, including high production rates and declining cut-off grade schedules. In practice, however, frequently there are operations that diverge from such NPV-maximising properties. Although a range of reasons for this can be at play, one possible explanation is that operators intuitively adjust their strategies to compensate for the flaws inherent to NPV maximisation. In particular, NPV analysis does not reflect the benefits of managerial flexibility inherent in a mining plan. Real options valuation (ROV) is an alternative approach that addresses this issue. We compare the properties of NPV and ROV optimisation solutions generated for the same scenario. Our simple case study demonstrates that the presence of real operating options in the optimisation model not only entails increased project value as expected, but also tends to encourage lower processing capacity (with lower associated capital cost), higher cut-off grades and greater use of stockpiles.CITATION:Elkington, T and Gould, J, 2012. Real option value optimisation, in Proceedings Project Evaluation 2012 , pp 35-40 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 24, 2012

By M Carr, C Wheeler, M Lurie, B Chen

The demand for steel products in modern society is prompting the iron ore industry to optimise their operations to ensure sustainability of fines and lump products. One of the key components in the iron ore transportation chain are belt conveyors. The energy consumption of modern belt conveyor systems has reduced considerably over the past few decades, however, there is still significant scope for further reductions, especially when heavily loaded long overland belt conveyors are considered. A new rail based continuous bulk material transportation system has been developed by researchers at the University of Newcastle to reduce the energy consumption of heavily loaded and long overland conveyors. The Rail-Running Belt Conveyor technology is a state-of-the-art continuous belt conveying technology which provides an innovative and novel departure from conventional continuous bulk material transportation systems with significant energy and economic benefits. This paper presents an overview of a Rail-Running Belt Conveyor variant which considers an enclosed belt. Enclosed belt conveying has the benefits of encapsulating the bulk material, and thereby reducing dust emissions and moisture ingress, in addition to being able to negotiate smaller radius horizontal and vertical curves leading to greater flexibility. To quantify the primary differences between conventional conveying technologies, the Denver office of thyssenkrupp Industrial Solutions (USA) developed a case study for an 11 km long conveyor. The conveyor design throughput was 2750 t/h and included a small net elevation loss of 10 m. When considering CAPEX the Rail-Running Pipe Conveyor equipment supply cost is approximately 45 per cent of the cost of a conventional pipe conveyor, while savings upwards of US$50M emerge for CAPEX combined with five years of OPEX. The savings vary with the topography and density of the bulk commodity, with iron ore generally showing increased savings because the high bulk density increases rubber losses in conventional conveyors.

Nov 8, 2021

Sample preparation for gold samples, where the distribution and size of gold particles is often irregular, usually demands that a relatively large sample weight is taken to produce a representative sample for analysis. Traditional sample preparation of gold samples incorporated multiple stages of coarse particle size reduction followed by subdivision of the sample prior to final fine pulverising. This technique developed because of the limited equipment options available to laboratories. As a result significant errors are introduced and the final sample size being pulverised is a small fraction of the original sample weight. Three significant developments have occurred in the last 25 years to significantly improve sample preparation of gold samples: 1.  large capacity fine pulverising,2.  fine jaw crushing, and3.  whole sample coarse pulverising. In the mid-1980s an Australian manufacturer developed large capacity pulverising bowls which had the ability to reduce samples with a mass of 1.5 - 3.5 kg to a nominal 0.075 mm product in approximately three to five minutes. Laboratories were able to produce a large homogeneous pulverised sample which significantly reduced the error in sampling. However, exploration and mine samples are usually 7 to 10 kg and the sample requires a subdivision stage following crushing to produce the 3.5 kg for the pulverising step, thus introducing potential for significant error. The development of fine jaw crushing allowed particle size reduction to -2 mm which reduced the subdivision error of the bulk sample prior to fine pulverising. Subdivision of the crushed sample at -2 mm still results in potential sampling errors, where the gold particles are not sufficiently liberated to be representatively sampled. Clearly the best option would be to reduce the particle size small enough to ensure a representative sample prior to final pulverising. Continuous mills offer a partial solution but are relatively slow and subject the sample to differential pulverising prior to subdivision. Clearly this does not provide the best solution for routine laboratory applications where high volumes of samples are to be processed. The recent development of a large capacity coarse pulverising system allows samples of up to 10 kg to be reduced to -0.25 mm prior to subdivision, and fine pulverised to -0.075 mm. Laboratories now have the necessary equipment to perform reliable large capacity sample preparation of gold samples. The exact choice of a sample preparation scheme may still depend on particular ore types but the need for multiple crushing and subdivision stages is redundant.

Jan 1, 2008

By C Mpodozis

Central Andean (22¦S to 34¦S latitude) Miocene giant ore deposits share common features that reveal their origin. Tectonic and magmatic features include a relation to a shallow subduction zone, an association with the waning or initiation of a magmatic episode, emplacement at the time of uplift associated with crustal thickening and formation at times of major magmatic changes along the Andean margin. Rare Earth Element (REE) signatures in magmas erupted near the time of mineralisation indicate a progressive change from equilibration at depth with a hydrous, intermediate-pressure amphibole-bearing mineral residue to equilibration with an anhydrous high-pressure garnet-bearing assemblage. These features point to a common history. First, a relatively shallow subduction zone leads to hydration of a cool mantle wedge providing a source of fluids which builds up over at least several million years. Arc magmas formed at this time equilibrate with a hornblende-bearing residual mineralogy. Second, a compressive tectonic regime leads to crustal shortening and thickening that facilitates entrapment of arc magmas in the crust. Eventually, the magma-weakened crust yields to horizontal compression causing rapid crustal thickening. Fluids required for mineralisation are liberated as amphibole-bearing assemblages break down to garnet-bearing ones and over pressured fluids are released from plutons. Mineralisation subsequently ceases in the region unless continued dehydration of the slab and mechanical thinning of the continental lithosphere causes the previous conditions to repeat. The type of mineral deposit generated depends on the pre-existing continental lithosphere and the distance from the trench.

Jan 1, 1999

By C M. Ramotsabi, F Bornman, W Erasmus

Spiral concentrators are gravity based separation devices used for the preparation of coal, iron and heavy mineral ores (Wills, 1992). Gravity concentration remains the main separation method for fine iron ore and is used extensively for treating many minerals. Gravity concentration methods separate minerals of different specific gravity by their relative movement in response to gravity and one or more other forces, the latter often being the resistance to motion offered by a viscous fluid such as water or air (Wills, 2006).The main operating variables for a spiral concentrator are the feed rate, the slurry concentration, the wash water addition and the position of the splitters used to separate the tailings, middlings and concentrate streams (Sadeghi, Bazin and Renaud, 2014). Wash water is an important control variable used to wash away entrapped light minerals from the concentrate stream (Burt, 1984; Bouchard, 2001). Sadeghi et al concluded the spiral operation to be sensitive to the wash water flow addition and resultant economic trade-off. Increasing the wash water flow rate increases the concentrate grade at the expense of the iron recovery.The paper addresses the effects of dripping wash water onto the concentrate stream of a spiral processing fine iron ore. The dripping wash water system offers a low flow alternative and could possibly provide a good balance between grade and recovery of valuable minerals without using excessive water. The Multotec SC20HC/7 WW spiral was used for the experimental test work. The spiral was tested at varying solids concentrations; the wash water rate and the splitter positions were kept constant.The use of wash water at 30 per cent, 35 per cent and 40 per cent solid concentration improved the Fe grade in the concentrate by about 1.5 per cent, six per cent and eight per cent respectively. The additional SiO2 rejected by the wash water is approximately three per cent, nine per cent, and 11 per cent at 30 per cent, 35 per cent and 40 per cent solid concentration respectively. Addition of wash water is shown to have minimum effect on grade at 30 per cent solid concentration, and Fe upgrades obtained with and without wash water were found to be similar. Notable upgrades were observed at 35 and 40 per cent solid concentration with wash water. The results obtained suggest that the additional SiO2 rejection by wash water increases with an increase in solid concentration. This suggests that the benefit of using the drip system is notable at higher solid concentration. It is believed that at lower solid concentration SiO2 particles are reasonably free to move around and are possibly less entrapped than at high solid concentration.The Fe grade/recovery and solid concentration relationship with wash water showed a non-linear correlation. The Fe grade increases with an increase in solid concentration up to a somewhat optimum point and then drops as solid concentration increases further. The recovery of Fe on the other hand follows a converse relationship with solid concentration, the recovery decreases from 30 per cent to 35 per cent solid concentration and then increases again at 40 per cent solid concentration. The increase in recovery at higher solid concentration could possibly be explained by the fact that the mass yield to concentrate also increases with solid concentration. Since recovery is a function of both grade and mass yield, the higher recovery at 40 per cent solid concentration is likely due to the high mass yield obtainable at 40 per cent solid concentration.The drip system could therefore possibly offer a safe guarding against grade and solid concentration variations without using excessive water, and possibly ensure that a product within specification is maintained.CITATION:Ramotsabi, C M, Erasmus, W and Bornman, F, 2015. Optimisation of wash water on an iron ore spiral to improve grade, in Proceedings Iron Ore 2015, pp 175–184 (The Australasian Institute of Mining and Metallurgy: Me

Jul 13, 2015

By A Whaanga, W Vigor-Brown

IGO Ltd’s (IGO’s) Nova-Bollinger Deposit (Nova-Bollinger) is a magmatic nickel-copper-cobalt (NiCu-Co) sulfide deposit found 160 km east-north-east of the town of Norseman in Western Australia (WA). The deposit is hosted by the Mesoproterozoic rocks of the Fraser Zone, which is part of the Albany Fraser Orogen (AFO). Since mining commenced in 2016, IGO’s Nova Operation (Nova) has mined and processed to 31 December 2020, 5.63 Mt of ore grading 2.04 per cent Ni, 0.86 per cent Cu and 0.07 per cent Co. Nova’s mine geology team (MGT) has used commercially available implicit modelling (IM) and general-purpose resource modelling (RM) industry software systems, to prepare the 31 December 2020 (CY20) update of Nova-Bollinger’s JORC Code reportable Mineral Resource estimate (MRE). This CY20 MRE update was predominantly based on ~386 km of diamond core drilling, with the drill holes having a nominal grid spacing of 12.5 by 12.5 m throughout the mineralised zones of the deposit. Using IM tools, Nova’s MGT interpreted and modelled 22 separate domains from the drill hole logging, assaying results, and the MGT’s underground mapping. These IM closed volumes were then used to control the estimation of MRE variables into conventional industry digital block models using RM and other ancillary software systems. During 2021, a commercial machine learning (ML) software was trialled by Nova’s MGT for preparing block models of Nova-Bollinger’s MRE domains. The motivation for the trial was that the ML process could expedite modelling through the direct creation of a domain coded block model from the drill hole logging. Compared to the industry standard approaches of wireframing or IM, where the modeller usually makes many subjective choices to produce the domain model, ML offers a more objective ‘hands-off’ process for determining the connectivity of domains defined in drill holes. Additionally, the ML process provides a quantitative confidence metric associated with its output that may have utility in mine production and resource classification. In this paper, the results of the Nova-Bollinger ML modelling trial are compared to the MGT’s current workflow for MRE work. The MGT’s conclusions as to the advantages and disadvantages of the IM and ML methods for preparation of MRE domains are discussed. The ML software was also tested as a method of rapidly interpreting geology outside the principal zones of MRE interest. These testing results are also presented in this paper.

Mar 22, 2022

By H Guthrie, J Hodder, J Bain, S Durkin

Australian mines have traditionally relied on diesel powered vehicles to fulfil their light vehicle needs. There are many reasons for the resources industry to review its use of diesel-powered vehicles. The international industry has developed projects to explore the use of Battery Electric Vehicles (BEV) as a more sustainable alternative to traditional diesel-powered vehicles. While the technology for cost-effectively applying modern high-performance lithium-based batteries to the mining environment has existed for over a decade it is yet to be widespread throughout the industry. Through the collaboration of Safescape, 3ME Technology and Kirkland Lake Gold, with funding from Mining Equipment technology services (METS) Ignited, the project has focussed on advancing the Australian METS sector’s capability in the rapidly approaching implementation of BEV technology. This paper reports on the collaborative approach to develop a prototype vehicle; explains the selection criteria for the various components of the vehicle; and details the risk-based approach to developing a scalable product to replace existing underground light vehicle fleets. The prototype vehicle was tested underground at Kirkland Lake Gold’s Fosterville operations in Victoria beginning in October 2019. Reporting from these trials focusses on the key factors affecting underground operations. These include driveability, safety, charging and cycle times. Gathering data around energy consumption through normal daily duties enabled a model of energy consumption and charging requirements to be developed such that various applications of the electric vehicle can be considered against existing diesel-powered vehicles. This has provided insight into the impact on daily operations, and the way forward for large scale implementation.

Mar 15, 2021

ILZRO sights are locked securely on the targets of the expanded applications and ever-improving quality in the major market for zinc-coated steel. A wide range of ILZRO-sponsored research projects examine issues of formability, paintability, and corrosion resistance for traditional hot-dip galvanising, electrogalvanising, and ILZRO's own proprietary zinc coating, Galfan. Recent research has focussed on the on the interaction between Galfan and different substrate steels to determine optimum combinations for different applications. ILZRO enjoys an evolving role in providing the connection between research laboratories and marketing divisions through supporting research and services for the Galfan Technical Resource Centreò(GTRC) and the recently formed North American Galfan Development Authority (NAGDA). GTRC has just produced a new problem-solving manual that provides a comprehensive source of hands-on solutions for the many Galfan licensees throughout the world, and should contribute substantially to the reputation of Galfan as a consistently top-quality steel-coating product. Meanwhile, NAGDA is advancing the market with new advertising for Galfan based on superior corrosion-resistant qualities proven through ILZRO-sponsored research. Practical manufacturing issues remain at the forefront of ILZRO priorities, with research emphasis on cutting and welding zinc-coated steel to provide direct assistance towards improved product quality and a more secure market. Moving to the arena of die casting, when the specifier looks to zinc to fill a design need, ILZRO-sponsored research projects provide comprehensive documentation on metallurgical characteristics for every zinc alloy under almost any imaginable application. On-going ILZRO-sponsored research is integrating this wealth of data with sophisticated computer programs that model die-casting designs with ever-increasing accuracy, as other ILZRO projects lay the market groundwork for zinc in applications ranging from vibration damping to electromagnetic shielding.

Jan 1, 1993

By E R. Ramanaidou, M A. Wells

Reflectance spectroscopy is now an established technique for mineral exploration and ore characterisation. The efficacy of the technique as a tool to characterise the main iron ore and gangue mineralogy at African Minerals Ltd’s Simbili iron ore deposit in north-central Sierra Leone was tested through reflectance spectroscopic analysis of 13 000 pulped drill reserve samples using CSIRO’s HyLogger-1™ system. Specifically, integration of reflectance spectral data with more traditional methods of analysis, such as geochemical analysis and Satmagan measurements, characterised the mineralogy (ie hematite versus goethite) of the oxidised ore at Simbili, quantified the Al associated with goethite and hematite and evaluated the distribution of the main gangue minerals – kaolinite and gibbsite. Relative changes in the Fe2+/Fe3+-bearing oxide and silicate mineralogy, based on mineral indices derived from reflectance spectroscopic measurements, appeared well-related to changes in the ore profile mineralogy consistent with the main ore types identified at Simbili, as representative of an oxidised banded iron formation sequence. Spectral calibration models, developed from a well-characterised training set of mineral mixtures, representative of the oxidised ore zone mineralogy were used to quantify the distribution of Al associated with kaolinite and gibbsite and the iron oxides, goethite and hematite. Combining these mineral spectral parameters with compositional data enabled the differentiation of Al-substituted goethite and hematite and resulted in the identification of low Al-bearing, or ‘clean’, goethite and hematite from high Al-bearing, or ‘dirty’, goethite and hematite. Spectral quantification of the iron oxide Al composition provides a far more rapid means of quantifying the Al substitution in iron oxides at the deposit scale compared to traditional techniques such as X-ray diffraction analysis. It also enables a level of volumetric characterisation and the potential for large-scale (ie three-dimensional) mapping, which was not previously possible with other techniques. The potential of the technique was also highlighted when mapping the distribution of the main Al-bearing contaminants (gibbsite and kaolinite) identified in the oxidised ore zone at Simbili. Delineation of such zones provides a guide to managing the most appropriate processing options (ie upgrade potential) within a mineralogical framework. Three-dimensional modelling of the gangue phase distribution may also allow the mapping of lithological and/or structural controls that may be prevalent at Simbili. This work highlights the value in the application of HyLogging™ technology for rapid resource characterisation, particularly for volumetric identification and mapping the distribution of both the economic and gangue phases, which otherwise would be difficult to achieve. As such, the technique can provide a fast and inexpensive means to evaluate ore and gangue mineralogy at the deposit scale and provide a first-pass assessment of the mineralogy and compositional attributes, with the potential to better predict ore metallurgical properties.CITATION:Wells, M A and Ramanaidou, E R, 2015. Waste not, want not – delving deeper into the Simbili iron ore deposit using HyLogging™ scanning technology, in Proceedings Iron Ore 2015, pp 337–346 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015

By Nilmani M, Fountain CR

Injection of gases into slag-melt mixtures produces various zones as a result of bubble formation and disintegration within the melt. The extent of these zones depends on the type of reactor used. When compared with ferrous processes, non ferrous processes are character- ised by large bubbles formed adjacent to the tuyeres, low flowrates and shallow tuyere sub- mergence. These features can result in a greater proportion of reaction occurring above the bath, more refractory wear and tuyere blockage with more splashing. The large bubble zone adjacent to the tuyeres has been investigated using the tech- niques of physical modelling, mathematical modelling and plant trials. Large bubble form- ation in physical models was recorded using a high speed camera and a rapid response pressure transducer coupled to an oscilloscope and data recorder. It was found that the bubble volume (Vb) could be correlated at low flowrates using the single bubble model Vb = 1.378 Q6/5 g-3/5 Deviations from this correlation occurred with increasing gas jet momentum. Plant trials were carried out on a copper converter at Mount Isa Mines during five different charges. Pressure measurements were made through the tuyeres during the slag blow and commencement of the copper blow. The power spectrum density showed that the dominant pulse amplitude occurred at a frequency of approximately 3 pulses/sec. Plant data from this and other converters were correlated using the same relationship as for physical modelling. De- viations occurred due to the state of the re- fractory, bath composition or bath circulation effects.

Jan 1, 1984

By R Battison, R Duggan, S Esen, K Henley, P Dare-Bryan

Increased catch bench crest loss has been observed in recent years at Barrick’s Cowal Gold Mine situated in central New South Wales, Australia. A project was initiated to diagnose the cause of the crest loss, and evaluate ways to limit its effect on final walls.A range of different blast measurement techniques were utilised to evaluate the progressive damage caused to catch berms by presplit, production and trim blasts. Techniques employed included; single point vibration measurement, cross-hole seismic analysis, precision berm surveys, horizontal p-wave velocity measurements, crest loss volume calculation and water level changes between blasts.Blast measurements showed that the majority of damage to the catch berm was caused by the presplit blasts, which registered vibrations greater than 700 mm/s at 5 m behind the presplit line. As a result, considerable changes were made to the blast designs after a series of computer simulations via mechanistic blast modelling (MBM). The uncharged presplit collar was increased from 2 m to 4 m, and every second hole was left uncharged. Vibration modelling using a multiple seed wave (MSW) model was used to optimise trim blast delay timing. Burden relief was changed from 16 ms/m to 27 ms/m using one hole firing per 4 ms time window, and the initiation angle was changed from shallow to steep. These changes in the presplit loading and trim timing helped reduce catch bench crest loss by 1–2 m.Trim shots using a high strength bulk emulsion explosive were also identified as contributors to berm damage after analysis of blast monitoring and MBM modelling. The modelling study resulted in the generation of alternative blast designs to minimise the crest loss, including the use of low-density/low-velocity of detonation (VOD) bulk explosive product (Flexigel™ Advantage) in trim pattern designs. This was trialled on the Northern and Eastern pit walls to evaluate the damage to catch berms on final walls. The trials demonstrated that berm vibration was reduced significantly; fragmentation was similar (or slightly blockier) compared to the fragmentation using the old blast designs; displacement of the berm was reduced, so increased catch bench widths were attained. This paper summarises the trials, and presents a summary of the crest loss to date.CITATION:Battison, R, Esen, S, Duggan, R, Henley, K and Dare-Bryan, P, 2015. Reducing crest loss at Barrick Cowal Gold Mine, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 189–202 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

THE South Mine. owned by the Broken Hill South Limited, occupies mineral leases 7 and 8 on the Broken Hill lode. The ore reserves are 4,250,000 tons, and the ore hauled for the year ended June, 1930, was 387,000 tons, the total to date being 7,840,000.The mine, down to the 1070-ft. level, is naturally divided into two sections, the northern and southern ends. Ore extraction is practically completed in the northern end to this horizon, while the southern end is developed ready for a concentrated attack.Fig. 1 shows the state of the 8215-ft. level, after connection to the new shaft.The levels above and below to the 1070-ft. level are in a similar condition, while below the 1070-ft. level the stoping has been confined to the north end, but not completed. The south end on these levels is also partially developed.The ore at present is hauled up No. 1 shaft, which is centrally situated to the present workings. This shaft was put into use in 1909, and in 20 years has had approximately 5,000,000 tons of ore pulled through it.The company, having proved the existence of large ore-bodies in the southern end of the mine, decided to sink No. 7 shaft. This is a six-compartment frame-set shaft (see Fig. 2) equipped with two cages and two 5-ton skips, the remaining compartments being utilised for electric cables, pipes, and ladders. The surface arrangements will include a steel head frame, electric winders, and breaker station.

Jan 1, 1930

By Blaskett K. S

The physical properties of monazite and the minerals with which it is associated in east coast beach sands are studied and discussed. Possible means for improving recovery are examined. In particular, it is suggested that the practice of splitting the heavy mineral concentrate into two parts as a preliminary to treatment in separate "rutile" and "zircon" mills can be modified in a simple fashion by the addition of an extra magnetic separation stage so as to aid monazite recovery.INTRODUCTIONBeach sand deposits on the east coast of Australia are a major source of rutile and zircon, and supply 80 per cent or more of world requirements. The deposits also contain a small amount of monazite, averaging about 0.5 per cent of the total heavy minerals. Yet despite a steady price in recent years of £150-160 per ton, monazite production has remained relatively small.On the basis of rutiIe production, potential monazite production on the east coast was about 1,500 tons in 1956, but only 102 tons of high-grade concentrate was produced. The main deterrent to increased production has probably been the capital cost of the necessary equipment. Separate electrostatic and magnetic equipment and separate table concentration and drying constitute a considerable outlay for a by-product contributing 4 to 5 per cent of the revenue from rutiIe.It is the purpose of this paper to discuss monazite concentration generally and to suggest modifications to flowsheets, which may facilitate monazite production while maintaining the main objective, simple and cheap means for maximum rutile production.

Jan 1, 1958