Search Documents

By Marshall GA, Dickerson AW

The efficient operation of large haul trucks in large open pit mines requires an economic trade off between the haul route quality, the haul truck payloads and the level of haul truck reliability. This paper describes an investigation into the relation- ship between haul route surface quality and the level of structural reliability of a haul truck main frame. An instrumentation system for unattended recording of data on a haul truck operating normally in a mine and com- puter based analytical procedures were developed and used to identify which road segments contribute significantly to fatigue cracking at various sections of a haul truck main frame. INTRODUCTION In many open pit mines there is exten- sive use of large haul trucks to move over- burden and minerals. In most open pit hard rock mines, both the overburden and mineral ore are moved by large rear dump type haul trucks. Similar haul trucks are also widely used for coal overburden and mine site coal haulage operations in New South Wales, South Australia and Western Australia. Large bottom

Jan 1, 1982

By J-P Franzidis

A technique for determining the recovery of attached particles across the froth phase in flotation that relies on measuring the rate at which bubble-particle aggregates enter the froth is used to investigate the selectivity of attached particles across the froth phase. Combining these measurements with those of other techniques for determining the froth recovery of attached particles provides an insight into the different subprocesses of particle rejection in the froth phase. The results of experiments conducted in a 3 m3 Outokumpu tank cell show that the detachment of particles from aggregates in the froth phase occurs largely at the pulp-froth interface. In particular it is shown that the pulp-froth interface selectively detaches particles from aggregates according to their physical attributes.

Jan 1, 2005

When Matthew Flinders entered in his log `This land forms the South side of the large bight; and besides projecting beyond the coast line, and being a little higher than usual is remarkable for having some reddish cliffs in it, and deep water near the shore', he was commenting on the deposit of bauxite at a place now known as Weipa. This sighting took place on 9 November 1802, and probably represents the first direct entry in Australia acknowledging a potential mineral deposit. Flinders, of course, had no idea as to what he was looking at, nor did he land to determine its content. If he had, he probably would have had no idea of the substance, and even less knowledge of its use. Nothing further was done to this for about 150 years.

Jan 1, 1993

By Korsch RJ

Permian oroclines in eastern Australia must have formed by sliding on a detachment surface. It is identified as a westward- dipping Devonian and Carboniferous sub- duction zone. Major strike-slip faults probably sole out on the same surface. One major fault with an associated serpentinite belt was pulled away from the craton abd bent into loops. Basins formed in the loops.

Jan 1, 1987

The patterns of flow of reaction gases through the flash furnace at the Kalgoorlie Nickel Smelter were simulated in a 1:20 scale model using a flow of water. Particular features of the flow down the reaction shaft, through the settling chamber and into the uptake leading to the waste-heat boiler were examined. Inferences were made concerning the effects of the patterns of flow on the efficiency of the smelting reaction, on the entrainment of dust by the gas stream and on the erosion of the refractory lining of the furnace. In addition, the effects of geometrical modifications to the arrangement of the concentrate burners and to the profile of the settling chamber were explored by making these changes to the model and observing the resulting variations in the patterns of flow.

Jan 1, 1991

By J F. Carswell, G Cheshire

The Pajingo gold operation in Queensland is approximately 55 km south of Charters Towers and 134 km south-west of Townsville. The gold deposit was discovered on the northern end of the Drummond Basin in 1983 and first open pit production began in 1986. Mining progressed underground in the 1990’s and gold production peaked in the early 2000’s as the main Vera/Nancy lodes were extracted, producing 330k oz in 2003 (a record at the time). More recently, as Ore Reserves and grade have diminished, the mine has had to develop innovative mining practices to maximise recovery of the remaining Mineral Resource. This has included a modified sublevel caving method against previously mined/backfilled zones. The method has been coined modified sublevel shrinkage (MSLS). Full scale trials of the new mining method have been successfully completed. This has allowed the site to revaluate the Mineral Resource and include areas into the Ore Reserve that were once deemed sterilised, adding significant value to the operation and extending its life-of-mine. This paper describes the first of two large scale MSLS trials and key operational learnings from it.

Mar 15, 2021

This paper is essentially an address, rather than a detailed presentation of facts, because the third edition of `Nuclear Electricity - An Australian Perspective' has just been completed and will be available for the seminar. That 96-page booklet contains a lot more information than The AusIMM would be prepared to print in the seminar proceedings. Hence I have kept this paper brief, and ask readers to obtain a (free) copy of Nuclear Electricity at the seminar or from The AusIMM. It can be read as a supplement to the paper (or vice versa). According to one of Australia's well known critics of nuclear power, Professor Ian Lowe, `the pro-nuclear lobby's predictions of the future use of nuclear energy .... have been regularly and consistently wrong by large amounts, always overestimating the future demand for uranium" (Aust. Society, April 1989). While I do not accept this as a bald statement applying to all those in favour of increased use of nuclear power, there is sufficient truth in it for it to be credible. Certainly in the 1950s and the 1960s, when the new technology for producing controlled power from atomic fission was first being commercialised, there were some very exaggerated projections of the role of nuclear power. Many people thought that it would take over from fossil fuel fired electricity generation in much the same way as the motor vehicle took over from horse-drawn transport. And these early projections were not simply concerned with electric power generation, they included excavating harbours and digging canals with nuclear explosives.

Jan 1, 1989

By Chowdhury P. J R, Biswas S. K

Recovery of metallic values from lean-grade raw materials as well as from secondary/intermediate industrial products is of immense importance to a country like India which is not endowed with extensive sources of copper and nickel. The results of a few studies carried out in this area are described in Part-I and Part-II in this article. A novel anode casting system, specially designed for a small copper refinery which had been set up to produce copper wire bars/rods is described briefly in Part-III.

Jan 1, 1992

The influence of pulp potential on the flotation behaviour of sulphide minerals in laboratory batch flotation tests is discussed in terms of self-induced flota- tion, collector-induced flotation, and depression.' Assuming that the pulp poten- tial is controlled by the same factors that determine the genuine redox poten- tial, an attempt is made to interpret the experimental results in terms of potential-dependent reactions based on bulk thermodynamic data. Self-induced flotation is displayed by many sulphides in moderately oxidizing solutions but not in reducing solutions. The available evidence suggests that the hydrophobic entity could be sulphur produced by superficial oxidation of the mineral but this has not been established beyond dispute. In general, flotation is observed near the potentials at which sul- phur would be expected to form and the minerals which produce sulphur seem to float the most strongly. Collector-induced flotation is most conveniently studied on minerals which have only slight self-induced floatab- ility. The mineral-collector interaction is potential-dependent hence flotation is generally only observed in limited ranges of potentials. While the general form of the floatability-potential relationship is similar to that predicted from thermody- namic data close correspondence between predicted and experimental results is not always observed.

Jan 1, 1984

I have chosen this topic for my address with the intention of preserving a rather extraordinary record of recurrent additions of capital in the financing of one of the world's important silver-lead-zinc mines. The recitation of the trials and tribulations which fore-shadowed the rise of Mount Isa Mines to a position of relative prominence in the realm of non-ferrous mineral production may, I hope, be of assistance to some of the younger members of the Institute who may be called upon during their careers to meet similardevelopmental and financial problems.Mount Isa Mines Limited was incorporated in New South Wales in 1924 with an Authorised Capital of 40,000 shares of £20 each.In November 1925 the Company acquired the leases and water rights of the Mount Isa Proprietary Silver-Lead Limited for 6,250 fully paid £20 shares. Shortly thereafter, but in the same year, the £20 shares were split up into £1 shares, thus bringing the Authorised Capital to £800,000.The leases purchased consolidated and brought under one management the principal ore bodies of the Mount Isa area.Transportation facilities were indispensable to the economic future of the field, so the construction of a railway extending the Government line from Duchess, 54 ,miles to Mo.unt Isa, was assured by the passage of a bill in October 1925 by the Queensland Parliament. Under the provisions of the so-called Mount Isa Railway Act the Company was required to idemnify the Government against national loss on this branch line for a period of 10 years.

Jan 1, 1953

By Beeforth C. G

The use of Non-Linear Programming to obtain improved schedules of future activity in two specific cases of mining and treatment of minerals is described. The two cases were (i) reclamation of gold, uranium and sulphur from old surface tailings dams and, (ii) underground mining of gold. The method used an augmented Lagrangian device to reduce a constrained Non-Linear Programme to a sequence of unconstrained hill- climbing procedures. The main advantages of the method appear to be those of (a)flexibility of modelling of industrial characteristics and constraints and, (b) reasonably modest computation times.

Jan 1, 1977

By Wharton P, Voigt R

In order to do the discharge estimation better, it is valuable to find out appropriate formulas for estimating discharge in various pits, based on accumulating data, summarizing discharge patterns applying optimum seeking method and principle, by seeking redical exponent with help of the method of exhaustion, as well as testing and making statistics, in accordance with the quality standards established by our practical experience.

Jan 1, 1988

The Hall-Heroult process is likely to be the dominant method of aluminium production for the remainder of the century. The characteristics of the operation of a modern smelter are described and attention drawn to their disabilities which are due chiefly to the small production capacity of individual cells.The principal components of the Hall-Heroult cell- the electrolyte, the anode and the cathodes are discussed in order to identify the problems of scale-up. The factors influencing current efficiency and energy consumption are analysed and lead to the conclusion that the greatest potential for energy saving lies in reducing the anode to cathode distance (ACD).The most promising direction for major change is in the application of a new titanium diboride-carbon composite for coating of the surface of the cathode carbon. It improves the wetting of the carbon by aluminium and should permit the use of sloping cathodes and anodes. The deep metal pad would thereby be eliminated and, in the absence of magnetic perturbations, the ACD could be substantially decreased.

Jan 1, 1987

By I M. Platten, S C. Dominy

The Clogau St DavidÆs gold mine has a recorded production of around 81 000 oz Au and it is the largest mine in the Dolgellau gold-belt and BritainÆs most prolific historical producer. The original mine was first worked for copper, however; in 1854, gold was found in waste material from the St DavidÆs section. In recent times the mine has operated intermittently between 1983 - 2007. The principal black shale-hosted gold-bearing reef (Main Reef) can be traced for about 3 km, striking approximately NE-SW and dipping steeply between 60¦ - 90¦ SE. The reef system pinches and swells, changes strike and splits into a number of smaller branches. Reef width is variable, ranging from over 6 m to a few cm and in places reducing to small irregular blobs. The reef is internally complex and composed of swarms of narrow (1 - 300 mm) subparallel veins separated by country rock sheets. The gold-bearing veins within the reef package are discontinuous; though generally possess bonanza grades running 10s - 100s oz/t Au. It has historically been shown that some gold-rich vein segments can grade up to 300 oz/t Au. The predictability of the gold-rich segments is poor, but has been shown to be related to presence of the Clogau (black shale) Formation, and/or the mechanical interactions of the reef with greenstone sills, reef branching and splitting and/or cross-fractures to form ore shoots. The mine is currently being re-evaluated as a potential small-scale selective operation.CITATION:Dominy, S C and Platten, I M, 2012. Geology, mineralisation and potential of the Clogau St DavidÆs mine, Dolgellau gold-belt, Gwynedd, Wales, in Proceedings Narrow Vein Mining 2012 , pp 101-120 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 26, 2012

Over the last five years Du Pont (Australia) Ltd has developed a commercial range of new generation emulsion based explosives concurrently with the development of new explosives-placement systems. The paper outlines Du Pont's emulsion technology and history of product development from the initial emulsions (Tovex E & EL) to emulsion/ANFO blends (Tovex BE) through to the most recent development of Du Pont's SOL emulsion component. The paper also outlines the development of materials handling systems on site to load waterproof bulk explosives from the original pumper trucks through to the multipurpose agitator bowl blending and pumping units at the heart of Du Pont's SOL emulsion system currently available within Australia. The last section deals with some of the more important features of enhanced agitator bowl truck designs and outlines examples of the complete SOL emulsion system and methods of operations currently practiced at specific mines within the Bowen Basin coalfields.

Jan 1, 1986

By Meyer C. F

The increasing use of continuous miners in the extraction of high coal seams has amplified the need for enhanced ventilation systems in the headings. Owing to larger face dimensions and higher production rates, more ventilating air is required to effectively dilute liberated methane to acceptable concentrations. However, the increased air quantities raise and entrain greater amounts of dust, to which the operator is subjected. Various methods (eg sprayfans, on-board scrubbers and jet fans) are used in various configurations and combinations to ventilate the headings. These arrangements generally result in a complex air flow pattern, which complicates achieving an optimum balance between diluting methane and minimising dust capture. In order to cost effectively investigate and propose solutions to this problem for the South African coal mining industry, the Division of Mining Technology has embarked on an extensive work program to evaluate various ventilation methods presently in use. Four currently generic ventilation patterns in various heading scenarios have been simulated using the Computational Fluid Dynamics (CFD) computer program. Evaluating these outputs against a predetermined set of criteria allows the best system for a particular situation to be chosen. The program also facilitates fine-tuning of an adopted system without incurring the cost and inconvenience of doing such tests in situ. This process not only provides solutions at significantly reduced costs, but also yields deeper insights into the factors affecting heading ventilation than hitherto possible.

Jan 1, 1995

By Ogilvie M

South Bulli is the oldest and largest underground coal mine in Australia. Two longwall units are in operation and current production is 2.5 to 3 million tonnes of run of mine product per year with a workforce of 600. Prior to 1984 a workforce of around 1,200 produced 1.5 million tonnes. Advances in technology can. of course, account for some of this gain, but the changes made in the human resources area are also seen as playing a major role in South Bulli emerging as a reasonably stable operation.The human resources strategy adopted recognises the value of the workforce and is aimed at not only fostering cooperation as all levels, but also making employees aware of the direct contribution they can make to the success of the enterprise.

Jan 1, 1991

A novel approach to validate size distributions obtained from bubble sizing techniques is introduced. The experimental rationale consists in verifying whether the output features the anticipated bi-modality when two uni-modal populations (ca. 0.5 and 5 mm) are mixed in a bubble column. The degree of deviation is quantified by comparing the calculated and real proportions on a volumetric basis. A sampling-followed-by-imaging technique was used to proof the concept. The results showed the anticipated bi-modality in which the real and calculated proportions corresponded with a deviation of less than 15 per cent, considered good given the severity of the test. However, the deviation was correlated to the superficial gas velocity (Jg) in the column and was consistently against smaller bubbles. Possible sources of bias are suggested.

Jan 1, 2005

By A D. Pradana, D R. Pradana, Y H. Putra, Z Zulhan, T Hidayat

The high temperature processing of nickel laterite ore is currently dominated by the Rotary Kiln- Electric Furnace (RKEF) technology. The ratio of SiO2/MgO (S/M) in the ore is one of the critical parameters that determines the success of the RKEF process. Incompatible S/M ratios in the ore can cause aggressive chemical interaction between the slag and MgO refractory. The slag-refractory interaction at conditions relevant to nickel laterite ore smelting was investigated in the present study. Synthetic mixtures representing the slag compositions of nickel laterite ore smelting were prepared by mixing MgO, SiO2, Al2O3, CaO, Fe2O3, and Fe and heating the mixtures in steel containers at 1300°C under an argon atmosphere for 3 hrs. Pure MgO crucible were used as containment material in the melting process of the mixtures to represent the MgO refractory. The kinetics of the slagrefractory reaction were investigated using samples with selected initial S/M ratios of 2.0 and 3.0 (wt/wt) (with constant CaO = 3 wt per cent, Al2O3 = 5 wt per cent, FeO = 10 wt per cent) by performing melting at 1500°C in MgO crucibles for 5, 30, and 120 mins under an argon atmosphere. The effect of the S/M ratio in slag on the slag-refractory interaction was also investigated by performing melting of mixtures with different initial S/M ratios of 1.75, 2.0, 2.5, and 3.0 (wt/wt) in MgO crucibles at 1500°C for 120 mins under an argon atmosphere. After the melting process, each sample was quenched in water, mounted in resin, ground, polished, and coated. The interaction between the slags and MgO refractory was then evaluated by analysing the polished samples using a scanning electron microscope equipped with an energy dispersive spectroscopy (SEM-EDS). Thermodynamic simulations using FactSage™ 8.0 thermochemical software were performed based on the experimental slag compositions, refractory, and conditions to support the evaluation process. The results show that a higher S/M ratio in slag leads to a higher tendency for the refractory component to dissolve into the slag. A higher S/M ratio in slag also leads to an increasing extent of solid-state diffusion of iron oxide into the remaining refractory grains. The dissolution of MgO into the slag is rapid; the MgO concentration in the final slag increased by 2.4 wt per cent and 5.7 wt per cent at initial S/M ratios of 2.0 and 3.0 wt/wt, respectively, within 5 and 30 mins of the melting process.

Aug 21, 2024

By P N. Duan, Z G. Liu, M S. Chu, X X. Xue, B Liu, G J. Cheng, T Jiang, J X. Liu

High-chromium vanadium-titanium magnetite has not been exploited and made full use of on a large scale so far due to the immature utilisation technology and the reality that the utilisation efficiency of valuable metals still urgently needs to be improved. In the present paper, the isothermal reduction kinetics and mechanism of high-chromium vanadium-titanium pellets were studied at 800–1100°C. The mineral composition transformation of pellets before and after reduction was analysed by means of X-ray diffraction (XRD), and the microstructures were examined by scanning electron microscope (SEM) equipped with energy dispersive X-ray (EDX) to reveal the elemental distributions. The effect of reduction temperature on the volumetric swelling degree and cold crushing strength was also studied. It was found that reduction temperature has a large effect on the reduction rate of pellets, and the increase in reduction rate is more obvious in the range 1000–1100°C than 800–1000°C. The volumetric swelling degree of pellets increased with increasing reduction temperature, while the cold crushing strength decreased. The transformation of mineral species can be expressed as Fe2O3 ? Fe3O4 ? FeO ? Fe, Fe2O3·3TiO2 ? Fe3O4· (2FeO·TiO2 ) ? 2FeO· TiO2 ? FeO·TiO2, (Fe0.6Cr0.4)2O3 ? FeO· Cr2O3 ? Cr2O3 , and Fe2O3· VO/V2O3 ? VO. The apparent activation energy of the reduction reaction was calculated to be 44.3 kJ/mol, and the reduction rate is controlled by the combined effect of interfacial chemical reaction and gas diffusion through the porous product layer. The rate controlling steps were further studied by calculating the resistance percentages. The interfacial chemical reaction was found to be predominant in the initial reduction stage, with the percentage effect of gas diffusion through the porous product layer gradually increasing during reduction.CITATION:Cheng, G J, Xue, X X, Liu, J X, Liu, Z G, Chu, M S, Jiang, T, Liu, B and Duan, P N, 2015. Reduction kinetics and mechanism of pellets prepared from high-chromium vanadium-titanium magnetite concentrate, in Proceedings Iron Ore 2015, pp 349–358 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 13, 2015