Search Documents

Water retention, water loss and delay in tailings storage rehabilitation are major challenges for many Coal Mines. Work by Stewart, Backer and Busch in the early 1980s suggested that there were improvements to be made in tailings dewatering and density by the addition of flocculant. This prompted ACARP, in cooperation with Bulga Coal Management (Xstrata), to initiate a research project investigating the impact of flocculant addition on tailings deposition density, water retention and the tendency for tailings to form surface crusts suitable for subsequent rehabilitation. A polyacrylamide-based flocculant (200 - 250 g/tds) was injected into the tailings line immediately prior to disposal into the impoundment area. The flocculated slurry rapidly released clear water and created a beach due to the immediate increase in deposition density. The deposition density increased from 35 per cent w/w to 61 per cent w/w solids within 24 hours and continued to increase to 75 per cent, seven days after treatment. The water capture at the tailings storage facility improved by more than 90 per cent; water which would otherwise be lost from the circuit through retention and evaporation. The impoundment capacity had nearly tripled due to the improvement in initial deposition density from 420 kg/m3 up to 1163 kg/m3. Four weeks after disposal surface crusts were forming on the storage facility, suggesting that there would be less delay between cessation and tailings storage rehabilitation.

Jan 1, 2008

By A Whaanga, A Doecke

The internal stratigraphy of the Marillana Creek palaeochannel Tertiary channel iron deposits (CID) in the Hamersley Province of Western Australia was initially defined in the 1980s and redefined as the Marillana Formation in the early 2000s. Recent drilling, open pit mining and field observations in the Western deposits at BHP Billiton Iron OreÆs Marillana Creek tenements have revealed some additional details on the extent and detail of some units of the Marillana Formation stratigraphy in this area. The drill hole data at Western 1 South has identified a number of features either not previously documented in this area or whose significance has not been adequately recognised, including a denatured zone at the base of the Upper CID of the Barimunya Member, and variations in the lithology within the Munjina Member at the base of the channel. Additionally, the Western 4 pit walls show evidence of a significant near-surface clay horizon and overlying CID, which are suggested to be the equivalent of the Iowa Eastern Member in the Eastern deposits. The deposition of this unit was most likely driven by a regional climatic disruption rather than a change in sediment source area alone. The nature of the Weeli Wolli Formation-derived goethitic peloids in the Western deposits may explain the more extensive denaturing in the Western Lower CID of the Barimunya Member. In contrast, the more robust nature of the haematitic-cored pelletoids in the Central and Eastern deposits has resulted in a less denatured Lower CID in these areas. Such work reveals the value of and need for geologistsÆ ongoing face mapping observations and detailed drill hole logging, and cautions against not querying previously accepted interpretations.

Jan 1, 2007

By B Dunstan, F Wirfiyata

PT Newmont Nusa Tenggara (PTNNT) operates the Batu Hijau copper and gold mine and process plant on the island of Sumbawa, Nusa Tenggara (Barat)  NTB, Indonesia. The plant consists of a nominal capacity 120 000 t/d conventional semi-autogenous ball milling crushing (SABC) circuit followed by sulfide flotation to produce a bulk copper concentrate for sale. Process control is effected by a plant wide distributed control system that overlays an extensive integrated programable logic controller (PLC) framework. The system is enhanced by a supervisory expert control system.Since plant commissioning in September 1999, over US$4 million has been expended as part of a systematic continuous improvement approach to optimise plant control performance. Works completed to date include: redesign and upgrade of architecture of the control system to ensure long-term system reliability, security and upgradeability and to provide a suitable platform for advanced control; integration of supervisory and advanced control tools, techniques and instrumentation; and implementation of sound network communication and plant data reporting tools. This paper outlines the evolution of process control and associated systems and tools that contribute to successful operation and ongoing performance optimisation at Batu Hijau.

Jan 1, 2009

Tholeiitic metabasalts comprise at least five geochemically distinct mafic volcanic associations of Late Palaeozoic age within the Gympie Province, southeast Queensland. Geochemical features indicate that parental magmas of the various metavolcanic suites were generated in contrasting tectonic regimes, although each of the suites shows some affinities with eruptives from convergent plate margin settings.Basalts from the Highbury Volcanics of the Gympie Group are island arc tholeiites (IAT) formed during an immature stage of eruptive activity in an intra-oceanic arc. They are unique among the analysed metabasites in possessing high Zr/Nb (Zr/Nb - 30) and very high Ba/Nb, and as well as low Ti/V, Ti/Zr and Ti/Y. These features are explicable solely in terms of contributions from a depleted, convecting upper mantle source, and large ion lithophile element (LILE) enriched fluids ascending from subducted oceanic crust.

Jan 1, 1990

This paper considers three aspects of cemented fill practice and research in Mount Isa. Firstly, an account is given of the use of Portland cemented hydraulic fill both in MICAF sills and in recovery of major horizontal pillars in the 650 copper orebody, where, during mining, cemented fill has regularly been exposed on unsupported vertical faces up to 90 ft high. In the paper the main considerations are the role and specifications of the fill used but also included is a brief description of fill preparation and placement.Data resulting from a Portland cemented hydraulic fill sampling, curing and testing campaign covering about 18 months of operating practice are presented, analysed, and discussed. These yield information indicating the mode of operation of a fully-automated fill preparation station, as well as a means of comparing field and laboratory strength results. A technique with potential for use as a fill quality control without actual strength testing is also described. The data collected showed that the fill station can operate within tolerances set on product quality, that laboratory and field strength results are comparable, and that rapidly obtained fillsample properties such as moisture content and void ratio can be related to cement content and strength, and hence used for quality control.Results of a fill research programme conducted by the author in Mount Isa since early 1968 are presented involving Portland cemented hydraulic fill and alternative, cheaper additives for cementing hydraulic fill. The most significant alternative to Portland cement is quenched and ground copper reverberatory furnace slag, whIch behaves as a pozzolan, reacting strongly with any available lime to produce cementitious hydrated calcium silicates and allowing Portland cement reductions of at least 50 per cent without strength loss.

Jan 1, 1971

Many metallurgical beneficiation and primary concentrating processes rely upon discrimination of products from gangue based on particulate density of the different minerals and combinations of minerals in an ore. The basic definition of density is simple, but the apparent density that minerals exhibit when in the environment of commercial densimetric separation processes is more complex and is ill-defined. Measurement of the apparent density displayed by minerals in their separation situation is essential if modelling of plant performance is to be meaningful or when comparison of an existing operation with a æperfectÆ separation constitutes a part of an audit or of a plant control function. Seven methods of dividing ore samples into discreet density fractions are examined and criticised in this paper. The shortcomings, difficulties and potential errors arising from the use of each method are evaluated. Most of the techniques described have been used by the author and generally their faults are understood and the resultant first-hand experience has been used to overcome these faults. A simple new computer-assisted technique for developing meaningful densimetric data is described.

Jan 1, 2004

By Eckersley J, Boyd G

A brief review is presented of the mechanisms and causes of spoil pile failures which have occurred at the Goonyella Mine. In particular, the results of a recent geo- technical investigation of the spoil dumps in the Cleanskin pit are briefly presented. Spoil pile hydrology is discussed in relation to the use of effective stress concepts in the analysis of spoil pile stability. Experience in relation to stabilisation of dragline dumps is discussed as well as the likelihood of current techniques being success- ful in the prevention of gross failures if prestrip material is placed in existing spoil piles. Parameters exerting a major control on dump stability are outlined.

Jan 1, 1981

By G Yeowart, P D. Munro

The Prominent Hill copper-gold concentrator of OZ Minerals Limited in South Australia was built in 2008 and commenced commercial production in early 2009. It has a design ore throughput of eight million tonnes per year (Mt/yr). While the flow sheet has many items in common with other plants treating ores from iron oxide-hosted copper-gold deposits, the Prominent Hill concentrator also has some unique features. Plant design has been based on a 'template' of the very successful Ernest Henry concentrator. Initial options considered for processing Prominent Hill copper-gold ore are briefly examined as well as potential complications arising from the presence of a considerable tonnage of 'gold-only' material present in the deposit. Metallurgical test work and the subsequent decisions leading to the selection of a conventional crushing, semi-autogenous grinding (SAG) and rougher flotation circuit is discussed. One particular difference with other plants treating this ore type is that metallurgical tests and mineralogical studies identified that rougher concentrate had to be reground to a P80 of 20 - 25 microns or finer for adequate liberation of fluorine-bearing minerals. Subsequent satisfactory separation of fluorine-rich gangue material from the valuable copper sulfides requires highly efficient cleaner flotation to make a commercial quality copper-gold concentrate. Xstrata Technology's IsaMillÖ and Jameson Cell technologies developed to meet similar taxing fine grinding and flotation duties for the treatment of the refractory zinc-lead-silver ores of the Carpentaria-Mount Isa Mineral Province were selected for regrinding and cleaner flotation. Plant design has features aiding ergonomics for ease of operation and maintenance not commonly seen in recent projects with large sulfide flotation concentrators.

Jan 1, 2009

New Zealand Steel Limited is nearing completion of the environmental reporting and planning procedures for its proposed fivefold expansion to steelmaking at Glenbrook, and supporting mining operations at Waikato North Head. A report on the proposal to transport concentrate from the mining operations to Glenbrook has also been prepared and is awaiting release. This paper draws from these events, and by discussing some of the problems encountered, gives some guidelines for the preparation of an Environmental Impact Report.

Jan 1, 1981

By Fitzgerald DE, Taverner MG

The principles, fields of application and equipment design concepts of several new approaches to continuous vacuum treatments of molten metals and alloys are discussed. Partic- ular attention is paid to the results of pilot plant tests evaluating a launder-in-tube method of 1. continuous production of refined zinc from a zinc-bearing lead produced in the lead splash condenser of the Imperial Smelting Furnace (ISF), and 2. continuous refining of crude cadmium. The former trials were not sufficiently encouraging to justify consideration of the process for commercial development. The applic- ation to cadmium upgrading gave very promising results; metal of 99.99 per cent purity was produced continuously at pilot scale (120 lb per hour) from crude metal containing 5.0 per cent Pb.

Jan 1, 1972

By Howell M. W

The purpose of this paper is to outline the main points in the construction of the various types of wire ropes more commonly used for winding in Australia; and the maintenance of the ropes, and cage and skip safety gear as practised at the South mine, Broken Hill.It should be mentioned that both of the shafts at present in use are dry, and both downcast with or without the assistance of the two exhaust fans normally in use: Night shift and week.-end overtime are practicaly non-existent.Thus, during night shift, the cages in No. 7 shaft are landed on the chairs at the surface, providing efficient covers for the· shaft, and allowing the maximum amount of rope to be wound on to the drums. This also applies to the cages of both No. 7 and No. 4 shafts during the week-ends.These factors, combined with electric winding and skip haulage, are calculated to obtain the best use of the ropes when properly attended.WINDING ROPES-TYPE AND CONSTRUCTIONThese ropes may be divided into four main types which will include the more commonly used constructions(a) One-size strand.(b) Warrington strand.(c) Flattened strand.(d) Locked coil.1. One-size strand as the name implies, is a rope the strands of which are constructed 9f wire of the one size.Usually the strands are of 7, 19 or 37 wires.

Jan 1, 1940

Optimum selection of explosives by means of monitoring explosive performance can lead to increased profitability through the control of fragmentation, a reduction in hangingwall and footwall damage and overall drill and blast costs. Studies conducted at the Mount Lyell Mining and Railway Company underground copper mine evaluated in situ the performance of four explosive types. Measurements included monitoring the levels of induced shock energy and the attenuation thereof with distance. The velocity of detonation (VOD) of these explosives was also measured using in-hole techniques. Assessment of these results, together with a knowledge of the rock mass strength, facilitated the selection of an explosive that was best suited to the given rock mass conditions.

Jan 1, 1995

The Mineragraphic Section of the Council for Scientific and Industrial Research has had occasion from time to time to examine rocks, ores and concentrates from the Yatukoula goldfield, Fiji. The results of the examinations have been supplied as Mineragraphic Reports and have been supplementary to various investigations carried out by the mining companies on ore treatment, or by visiting geologists on the nature of the rocks and lodes. The presence of tellurides was determined in 1935, though incorrectly as nagyagite. The general absence of lead, except in traces, was soon afterwards discovered, and it came to be recognised as the mines were opened up that the chief telluride minerals on the field were sylvanite and native tellurium. Specimens of the tellurides have been provided from time to time by E. G. Theodore, Managing Director of the Emperor Mines Ltd., and of the Loloma (Fiji) Gold Mines N.L., and further material was recently obtained, as the result of a visit to the field at the invitation of Mr. Theodore.The aim of this paper is to describe the occurrence of the tellurides in these specimens. The work has been carried out as part of the programme of research of the Mineragraphic Section.THE VATUKOULA GOLDFIELDThe Emperor, Loloma and Dolphin mines are situated at Vatukoula, six miles, south of Tavua, on the north coast...

Jan 1, 1949

By J R. Hernandez-Aguilar, C O. Go, C Acuna

The gas dispersion properties that are the subjects of this communication include three measured parameters, gas superficial velocity (gas rate), gas holdup and bubble size, plus derived parameter, bubble surface area flux. Over the past ten years sensors to measure these parameters have been introduced and those originating from McGill University are briefly described. The sensors have seen extensive use in plant campaigns and experiences on four cell types at three sites are discussed. The impact of frother in controlling bubble size by retarding coalescence is illustrated, introducing the need to understand chemistry/machine interactions in interpreting gas dispersion results. An increase in Sauter mean bubble size (D32) with superficial gas velocity (gas rate, Jg) was found, which followed the empirical relationship where Do ~ 0.5 - 0.6 mm and C and n are fitted parameters dependent on the system (machine and chemistry). Following this trend in Db - Jg, consistent bubble surface area flux (Sb) - Jg trends are also observed. The trend in Sauter mean versus number mean (D10) is used to help interpret the nature of the distribution; as the means approach numerically, the distribution is narrowing. Analysing gas holdup versus gas rate shows both a dependence on location in the cell as well as cell position in a bank, factors which must be accounted for when comparing data from different plants and circuits. The instrumentation and methodologies being developed are presenting new opportunities for incorporating cell hydrodynamics into metallurgical diagnostics. A case study at one plant serves as illustration.

Jan 1, 2005

By Pollard D. M

The effects of pH, temperature and the form of zinc used on the kinetics of cementation of cadmium from process liquors were investigated. Batch tests were conducted in stirred beakers, and the cementation reaction was found to be first order controlled. The rate controlling step was thought to be the diffusion of zinc ions from the zinc surface to the bulk solution. The pH was found to have a significant effect when using Prime Western zinc or zinc dust. High reaction rates were favoured at low pH levels and a minimum rate was observed at a pH level of approximately 5 to 5.5. The pH was found to have little effect when using high grade and cathode zinc. The reaction rates increased significantly with increasing temperature; a reaction temperature of 55¦C resulted in almost complete removal of zinc from solution. Effective cementation rates were only acheived with cathode zinc after pickling in acid. The nature and specification of zinc used determined the cementation rate of cadmium, resulting in the following order: 1. Zinc dust 2. Prime Western zinc at pH 3 3. High Grade zinc at pH 3 4. Pickled cathode zinc 5. Prime Western zinc at pH 3 6. High Grade zinc at pH 3 7. Cathode zinc "as received".

Jan 1, 1989

By Manlapig EV, Davis JJ

A methodology for modelling dense medium cyclones is presented for cyclones operating under conditions which avoid particle interference or apex crowding. Particle interference and apex crowding are shown to result in less efficient separations and represent undesirable regimes of dense medium cyclone operation. In order to avoid apex crowding, suitable medium to ore ratios and apex diameters should be used. Cyclone density differentials should be kept below approximately 400kg.m 3 to limit loss of efficiency due to excessive particle recirculation within the cyclone. The relationship between size-by-size partition curves shows that the flow split and density of the medium within a cyclone can be related to two new parameters, the pivot partition number and pivot density. The parameters are common to each partition curve in any set of size-by-size data and are mathematically related to the familiar performance characteristics, ecart probable (Ep) and separation density. The resulting expression confirms that the Ep and separation density are directly related.

Jan 1, 1986

The Amacan Copper Project was constructed in the Philippines by a Finnish-Filipino Consortium during the years 1979 - 1982. The project involved a turnkey contract for a mine and a concentrator to process 25 000 tonne per day of porphy- ritic copper ore at a grade of 0.45% Cu. The orebody is located on Mindanao, the southernmost island of the Philippines, in rugged, mountainous terrain approximately 1 000 m above sea level. The adopted design principle was based on an efficient, straightforward installation utilising a minimum number of items of equipment each with high unit capacities. The consortium faced many problems which resulted in lengthy delays in construction and finally led to the client taking over responsibility for the completion of the project. The concentrator was successfully commissioned in July 1982.

Jan 1, 1986

By Yanagase T, Nakamura T, Ueda Y

The possibility of removing the phos phorus and sulphur contained in steelmaking slag has been studied by observing directly through the microscope melts heated on Pt- filaments. After a CaO crystal was placed in the molten slag, distributions of P, S and other elements formed around the CaO crystal were determined with the aid of EPMA. The results indicated that a layer of 2CaO SiO2 is formed on solid CaO in CaO-Si02 melts. Then between CaO and the newly formed compound the molten slag tends to migrate through cracks. For higher Fe 2 03 contents, the layers of the compounds 2CaO.Si02 and 3CaO SiO2 formed around the CaO crystal are not continuous but look more like particles, which promotes the dissolution of CaO. Phosphorus in slag was found to be enriched in the 2CaOòSi02 layer. Phosphorus in the 2CaO SiO2 phase is not related to the primary slag composition, being about 5-7% P205.. Sulphur in slag,as well as the phos- phorus,was concentrated in the 2CaO.Si02 phase. Disintegration due to weathering observed for slags produced in these investigations appeared to be due principally to hydration of lime.

Jan 1, 1980

By T Hayward, G Lane, M Phillips

In December 2004 Phu Bia Mining Ltd commissioned Ausenco International Limited to conduct a feasibility study for its Phu Kham copper-gold project located in Laos. The feasibility study for a mining and processing operation treating 12 Mtpa of ore averaging 0.56 per cent copper and 0.25 g/t gold to produce an anticipated annual average 200 000 t of concentrate containing 25 per cent copper was completed in early 2006. The plant design incorporates a single processing line and includes a gyratory crusher, overland conveyor, coarse ore stockpile, SAG and ball mill grinding circuit, flotation circuit including regrind and three stages of cleaning, concentrate dewatering and concentrate load-out facilities. The Phu Kham copper-gold mineralisation comprises two principal styles: stockwork-disseminated and banded-massive sulfide within skarn limits. Primary copper in both mineralisation styles occurs as chalcopyrite and secondary copper sulfide minerals. Skarn includes the copper and gold mineralisation contained in pyrite, silicate, magnetite and haematite skarns, and in quartz-pyrite altered sediments. Both the stockwork-disseminated and banded-massive sulfide ores contain relatively high proportions of pyrite relative to the copper and gold mineralisation. Thus, the flotation metallurgy of the Phu Kham orebody is characterised by the need to reject a high proportion of the pyrite during differential flotation to yield a concentrate grade of approximately 25 per cent copper. The rejection of pyrite is accompanied by the rejection of some copper and gold and can result in modest metallurgical recovery. Consequently, the greater the pyrite content, the lower the expected copper and gold recoveries. The relative pyrite content is expressed on the basis of sulfur:copper ratio. For Phu Kham ores, the sulfur:copper ratios are in the range eight to 14 on a blended annual basis, but can be greater than 20 in the skarn components. Higher grades of copper and gold are also present in the skarn mineralisation. The design concepts for the concentrator were influenced by the need to provide a low capital cost approach for the project due to the relatively low grade of the ore and the modest metallurgical recovery. The concepts used to minimise capital cost whilst retaining operating and maintenance flexibility are discussed, together with the metallurgical challenges imposed by the high pyrite mineralisation.

Jan 1, 2007

By L Soares, W T. Hennies, F Fujimura

The engineering geological mapping of Metropolitan Area of Jopo Pessoa in the littoral zone of the Parafba State, northeast of Brazil, made possible the ambient characterisation for space using and its implications on the environmental resources. This region comes lately denoting an accented industrial growth and this work would help future projects of urban planning, distinguished by quick ground occupations for residential, industrial installations, farming, beyond mineral extractions. The mineral sector supplies material and substance demanded by industry and civil constructions, like as clay deposits, sands, calcareous rocks and mineral water. Many companies working there do not have the permission or inspection of ambient agencies for planned extractions of mineral resources. The consequences of this activity pass for the low profit of the reserves, bad uses of the sources, ground degradation, vegetation suppressions and physical impacts on landscapes, beyond noises and vibrations. These activities have causing accelerated alterations and transformations in the environment, compromising the sustainable development. It thus becomes clear that urgent solutions must be find to solve the problems with human interferences by closer inspection and management for disciplined use of its natural resources.

Jan 1, 2003