Search Documents

Traditionally, the predominant drilling method in open pit mining has been large hole rotary drilling using cumbersome, inflexible equipment offering merely limited scope for improvements in pit design and overall costs. By contrast, the recent development of comparatively light high-pressure down-the-hole hammer crawlers has paved the way for new ideas and trends. High penetration rates coupled with superior mobility and fast set-ups contributing to substantial productivity gains have resulted in a renascence for this drilling method in open pits. The ability to cover a wide range of hole diameters and angles gives designers unique drill pattern possibilities especially when establishing steep and stable pit slopes. As pre-split holes, buffer holes and production holes all can be drilled by using the same equipment, there are, there are obvious advantages in production scheduling as well as in materials handling and service. This paper presents some case stories, which will demonstrate the benefits and improvements that the introduction of new drilling methods and equipment has brought to open pit mining operations.

Jan 1, 2003

By A J. Moore

Predictive assessment of surface blast vibration requires the identification and quantification of significant factors, and the summation of their combined effect. Methods available for the prediction of significant factors are described, and examples are given of the combined use of these methods to evaluate alternative proposals.

Jan 1, 1999

By Bahsford A

The presence of coal in the Sydney area was confirmed in 1891 when Cremorne Bore No. I intersected cindered coal at 1 854 m. The decision to develop Sydney Harbour Colliery was based on the results of Cremorne Bore No. 2 (drilled in 1892) in which a 3.12 m. seam of unaltered coal was encountered at 889 m. Geologists from the New South Wales Department of Mineral Resources consider that this seam is probably equivalent to an upper split of the Bulli seam. Long Cove at Balmain was selected by Sydney Harbour Collieries Ltd. as the site for mine development in 1896. This was due to opposition to the proposed establishment of a colliery on the north shore of Port Jackson near Cremorne. Construction of the main access and ventilation shafts (termed Birth- day and Jubilee), other mine infrastructure and the quay wall occurred between 1897 and 1902. A fatal accident in which five men were killed occurred during the construction of the Birthday Shaft in 1900. This acci- dent resulted in amendments to the Mining Act providing for guide rails in shafts.

Jan 1, 1988

By J M. F Clout

The low-grade clay-rich -1.0 mm fraction of fine iron ores have often proved difficult to upgrade and capital intensive to process when using traditional wet beneficiation technology including single or two stage hydrocyclone desliming, wet high intensity magnetic separation (WHIMS), spirals and final dewatering using fine screens. Very fine (<0.010 mm) clay-rich slimes simply follow the water split to the hydrocyclone underflow where it often impedes the subsequent processing performance of any downstream spirals and can result in troublesome direct dewatering of hydrocyclone underflow. The -1.0 mm fraction in goethitic iron ores is typically considered as waste. A new two-stage wet gravity separation flow sheet, referred to as the ædesandÆ process, has been designed to overcome these issues for the upgrading of low-grade clay-rich goethitic or hematite-quartz fine iron ores. The desand process is designed to treat the -1.0 mm range from -8.0 mm natural fines, to recover a -1.0 +0.038 mm higher-grade fraction by rejecting to tailings any low-grade clay-rich ultrafines and low density sand-size fine chert/quartz gangue and shale.The desand process consists of wet screens with a nominal 0.7-1.0 mm cut point which direct the undersize to hydrocyclones. The hydrocyclone underflow is then fed to upcurrent classifiers where the classifier middlings is sent to spirals and classifier and spirals concentrates are then dewatered using vacuum belt filters or fine screens. The three product upcurrent classifier is employed to further deslime the hydrocyclone underflow, producing firstly a coarse final concentrate, and then a deslimed middlings for feeding to spirals as well as a 0.100 mm clay and fine quartz or banded iron formation (BIF) sand in final overflow for feeding to the residue thickener. The upcurrent classifier middlings provides the spirals with a significantly cleaner feed material than traditional methods, with the end result that the spirals do not silt up with slimes and therefore can continue to run at their optimum. The upcurrent classifier and spirals form a complimentary pair, with the upcurrent classifier better able to send coarser, acceptable grade particles to concentrate and fine slimes to tailings whilst allowing the spiral to better reject coarser, subgrade low specific gravity particles. Test results for the Mayoko-Moussondji iron project, Republic of Congo, using upcurrent classifier-Wilfley Table (simulating spirals) gave acceptable mass recovery from run-of-mine (ROM) and Fe recovery from hydrocyclone underflow for HEMCOL (6.2 per cent mass recovery from ROM/43.1 per cent Fe recovery) and HEMBIF2 (5.1 per cent mass recovery from ROM/22.3 per cent Fe recovery) mineralisation types. The desand process also enables improved dewatering of -1.0 +0.038 mm product from a clay-rich plant feed.A number of new wet plants in the Pilbara use the desand flow sheet including FMGÆs Cloudbreak and their two Christmas Creek plants. Many potential new applications are being explored, with new iron ore plants in India as well as those being proposed for West Africa. Operational experience has highlighted the importance of providing clean process water to the upcurrent classifiers as well as ongoing design improvements including increased wear life, reduced maintenance and enabling a more steady feed rate to spirals.CITATION:Clout, J M F, 2013. Beneficiation of fine iron ores using the desand process, in Proceedings Iron Ore 2013 , pp 337-348 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By L Grigorov, G J. Jame, A V. Nguyen

The dewetting kinetics between a small air-liquid interface and a silica (negatively charged in water) planar surface in solutions of dodecylammonium chloride (cationic surfactant) has been investigated using the Scheludko cell and digital high-speed video microscopy. The gas-liquid interface was created at the bottom of a small silica capillary of the cell and then was moved towards the silica planar surface. After the rupture of the liquid films between the interfaces, the expansion of the gas-liquid-solid three-phase contact (TPC) line was observed and recorded using a digital high-speed video microscope system, operating at 1000 frames per second. The surface tension of the surfactant solution was measured using the pendant drop technique. The equilibrium contact angle was measured using the Scheludko-Minings method with a silica micro-sphere. The TPC radius was determined as a function of time and compared against the available hydrodynamic and molecular-kinetic models. The experimental data are described very well by the molecular-kinetic model for the TPC line motion. The hydrodynamic model is in agreement with the experimental data only for a short time after inception of the three-phase contact expansion.

Jan 1, 2005

By L C. Thompson

Biomineralisation is the process by which microorganisms mediate and catalyse inorganic reactions so as to form new mineral assemblages. The goal of biomineralisation as a remediation tool is to control microbial processes and their environment so as to sequester and immobilise specific toxic metals within exceptionally strong bonds of neo-formed mineral assemblages. In this way, the bound metals are no longer mobile within a geological time-scale. Applied biomineralisation uses microorganisms, which are isolated from a metal waste environment and are selected for their ability to rapidly catalyse neo-mineral development from dissolved or leachable metals. A typical waste environment will contain microbes that contribute to the mobilisation of metal contaminants as well as microbes that possess the potential for remineralising available metals. Selection and augmenting the correct combination of bacteria and eliminating the competing mineral degrading reactions are the key to applying biomineralisation as an in situ remediation process. Applied biomineralisation harnesses the microbesÆ ability to stabilise toxic soluble metals into non-mobile mineralassemblages. This paper will discuss and demonstrate the biomineralisation process through several case studies including the Summitville mine site in Colorado, the McCoy-Cove mine in Nevada, the Argonaut mine in California, and an historic lead site in Crooksville, Ohio.

Jan 1, 2004

By A Radici, M Attwill

The Dampier Port Upgrade Project (DPU) involves an upgrade to Hamersley IronÆs Parker Point iron ore port facility at Dampier, Western Australia. The $US700 million DPU Project will increase Hamersley IronÆs shipping capacity at Dampier from 72 million tonnes per annum (Mtpa) to 116 Mtpa. The DPU Project comprises a new car dumper facility and rail spur, an upgrade to the existing stockyard and conveying system, a new screen-house and a 450 m wharf extension with two new shipping berths and a new ship-loader. This paper discusses the innovative design and construction of the new car dumper facility, which is capable of automatically unloading 240 car iron ore trains at a rate of 10 000 t/h. The facility design is unique compared to more conventional designs currently in operation, and greatly improves operation and maintenance functions.

Jan 1, 2005

Willemite mineralization was discovered in 1966 in the North Flinders Ranges of South Australia, in the course of a stream sediment sampling programme. Further work outlined a total of nine separate willemite occurrences in the Copley/Beltana area, and ten small deposits in the Toondana area south of Parachilna. Mineable reserves of 1 000 000 tonnes grading 36.8% zinc were outlined in three deposits in the Copley/Beltana area and campaign mining of the Main Orebody commenced early in 1974. The main group of deposits all occurred within red, dolomitized Cambrian Ajax Limestone, and most are associated with significant thrust faulting. The area of the Main Orebody group of deposits has been intensely fractured, and the surrounding dolomites are often brecciated and contain up to 5% zinc. Lead and arsenic mineralization are minor components of the main group of deposits. Masses of Middle Proterozoic Willouran Formation crop out adjacent to or close to most of the deposits in the Copley/Beltana area. The Willouran is frequently highly sheared, brecciated, and often contains large inclusions of younger formations. It is believed that most of the Willouran outcrops represent piercement structures.

Jan 1, 1975

By B OÆNeil

The Trent-Severn Waterway is a 386 km long navigation route through central Ontario between Lake Ontario and Georgian Bay, and is operated by the Parks Canada Agency. Its primary focus is to pass recreational boats through a system of 44 locks. The Big Chute Marine Railway (BCMR) is one site in the system that provides transportation for boats. The BCMR carriage is used to transport boats and their passengers on the inclined railway a distance of 230 m over a natural barrier from one body of water to another, with an elevation difference of 18 m. The unique feature of the haulage system used in this application is the variable angle of the incline from about 20 per cent rise changing to horizontal and followed by 20 per cent decline. In such conditions, unlike as in standard incline haulage, special configuration of hoists and drives is required. On the uphill part of the track, there is a need to have a motoring mode, on the downhill part a regenerating mode and on the horizontal part a combination of motoring and regeneration is required. The original system was built in 1978 and employed four 100 hp dc drive mine hoists to haul the 100 tonne conveyance loaded with 90 tonnes of boats. Due to failures and operational problems with the original system, in 1999 Parks Canada awarded a turnkey contract to ABB for a new, modern system of four single drum hoists. The new system was put into operation in 2000, only six months after receiving the order. The hoists are controlled by digital drives and a digital control system. Due to dramatic changes in the load conditions for individual hoists involved, the new system features many interesting solutions like changing drive modes from speed to torque control and a multiple, regulated braking system. It is a unique hoisting system, which could be also used in mining applications.

Jan 1, 2005

CONTENTSSummaryIntroductionGeographical and Geological Outline of the RegionGrowth of the Mining IndustryTable 1: Production StatisticsGeneral GeologyRecent Alluvium and River GravelsSambeto SeriesMudstone and Basalt ContactVatukoula SeriesIntrusivesStructureGeologic HistoryLodesTable 2: Principal Lodes and Their OrebodiesMineral Assemblage and ParagenesisOre Shoots and Their ControlEmperor MineLoloma MineDolphin MineExplorationConclusionAcknowledgmentReferencesSUMMARYThe Tavua Goldfield was found in 1932 within a basin, both topographical and structural, near the sea on the north side of Viti Levu, Fiji, and has produced over £13,000,000 (Fijian) worth of gold and silver from the three mines...

Jan 1, 1953

By Bhattacharyya A. K

The current methods for predicting pillar strengths are reviewed. A two-dimensional model, based on the Mohr-Coulomb failure criterion, is proposed for determining the compressive strength across the width of a long pillar. The model can be used to determine pillar strength and the depth of the crushed (ie yielding) zone from the pillar edges. The values of the parameters in the model, namely the cohesion and internal friction angle of the coal seam, friction angles at the contact of the coal seam with the roof and floor are determined by matching the strengths predicted by this model with the Bieniawski pillar strength formula for pillar width to height ratios up to 5. It is found that the derived values of these parameters are quite close to the results from laboratory tests. Based on the model, a preliminary analysis of pillar stability is made.

Jan 1, 1995

By R Graber, R Johnson

North American steelmaking practices have evolved based on access to iron ore raw materials containing very low phosphorus contents, typically less than 0.025 per cent P. Cleveland-Cliffs managed Tilden iron ore operation produces iron ore pellets exceeding 0.030 per cent P, which by global standards would be considered low phosphorus, but has limited penetration in the North American iron ore market due to phosphorus content. Recently cathodoluminescence microscopy has augmented more standard ore characterisation techniques enhancing our understanding of the genetic history and process mineralogy of TildenÆs complex martite ore. This paper highlights the unique capabilities that cathodoluminescence microscopy provides for phosphorus mineral identification in fine-grained iron ores.

Jan 1, 2005

Broken Hill is situated at an elevation of approximately 1000 ft. above sea-level, on the Barrier Ranges, in the State of New South Wales, Australia. It is approximately 700, 280 and 330 miles from the ports of Sydney, Pirie, and Adelaide, respectively.The summers are usually hot and dusty, with a recorded maximum shade temperature of 114° F. The rainfall averages approximately 9 in. per annum.

Jan 1, 1932

By Browne TJ

On 13 October 1993, a shallow earthquake registering 7.1 on the Richter Scale occurred near Tauta in the Finisterre Range of Papua New Guinea (PNG) killing 37 people. The aftershock series lasted three months and resulted in considerable landslide damage that destroyed villages, food gardens and airstrips, and blocked rivers causing catastrophic flooding. These effects have irrevocably altered the form of many of the valleys and rivers draining into the Markham and Ramu valleys.The earthquake occurred in a pilot study area for a landslide hazard mapping project being carried out by the PNG Geological Survey that commen-ced in April 1993. Comparisons made between areas identified as unstable during the study with those damaged by the earthquakes show good correlation.It is concluded that aerial photograph and Landsat TM imagery interpretation can be used with a high degree of confidence to identify potential landslide hazards in mount-ainous terrain. Landslide hazard maps are promoted as a tool for use in the route planning of roads and powerline corridors, as well as for identifying vulnerable communities.

Jan 1, 1994

By Milawarma E, Cusack C

The Sapan Dalam coal deposit of Indonesia consists of ten steeply dipping seams with thicknesses varying between 0.1 and 3.5 m and split by shale, clay, silt and sandstone. The area contains four faults dipping about 75¦ with four to 85 m vertical displacements. The complex nature of the deposit coupled with limited 27 exploration drillholes at an average spacing of 200 m made it difficult to create a realistic geological model. A three-dimensional gridded seam model gave a fair representation of the deposit. Attempt to create an optimum pit using the WHITTLE 3D pit optimiser proved unsuccessful since the pit optimiser is restricted to standard regular or fixed blocks. The gridded seam model was converted to a fixed block model prior to the optimum pit design. Smoothing and pit base controlling were also introduced to obtain a smoother pit. A mining scenario produced 3.6 million tonnes of coal, 28.4 million bcm of waste and US$18.1 million revenue.

Jan 1, 1995

Minerals similar to the indicator minerals used in kimberlite exploration are widespread in the Cainozoic alkali basalts of north Queensland. Magnesian ilmenite, pyrope garnet, chrome diopside, chrome spinel, phlogopite and zircon were recovered from most of the localities examined. The occurrence of these minerals creates significant problems when indicator minerals are used for diamond exploration. Basaltic ilmenite is visually similar to kimberlitic ilmenite. Untransported grains are rounded and have pitted surfaces. Basaltic ilmenite grains often have exsolution lamellae and reaction rims of titanomagnetite. Although kimberlitic and basaltic ilmenite are chemically similar, basaltic ilmenite grains are usually less magnesian than their kimberlitic counterparts. Basaltic ilmenite contains very little Cr203. Pyrope garnet occurs as megacrysts and in a variety of xenolith lithologies in north Queensland basalts. Most basaltic garnet is Cr-poor and comparable with kimberlitic garnet from Groups 3 and 5 of Dawson and Stephens (1975). Wine-purple, chrome-bearing garnet is common in kimberlite but rare in basalt.

Jan 1, 1984

By H Catchpole, L FontbotT, J PTrez, M Ageneau, A Bendez·

In the world-class mining district of Morococha, epithermal polymetallic replacement bodies and veins overprint porphyry mineralisation and skarns related to subvolcanic intrusions of Miocene age, thus indicating ore formation in two different environments, separated in time or forming a continuum. The district covers an area of about 70 km2 in the north-western part of the Domo de Yauli complex in theWestern Cordillera of central Peru and is part of the Miocene polymetallic belt, also hosting the deposits of Colquijirca (Bendez· et al, 2008b) and Cerro de Pasco (Baumgartner, FontbotT and Vennemann, 2008). Multiple late-Miocene porphyry stocks intruded Permian, Triassic-Jurassic and late-Cretaceous sedimentary carbonate and volcano-sedimentary formations, as well as large mid-Miocene barren intrusions. Extensive field work and detailedmapping of different styles of orebodies suggest that ore formation in the area was related to the late-Miocene magmatism. Good outcrop conditions and superimposing of different mineralisation styles make Morococha an ideal location for studying ore-forming processes in a complex porphyry-related magmatic-hydrothermal system in which porphyry-to-epithermal transition occurred. An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation.

Jan 1, 2008

By M Ridd

The Pasminco Century Mine (PCML) is located 250 kilometres north-north-west of Mt Isa in Queensland. As one of the worldÆs largest zinc mines, PCML comprises mining and milling operations at Lawn Hill, concentrate filtering and shipping facilities at Karumba in the Gulf of Carpentaria, and a 304 km slurry pipeline connecting the two operations.Mineralisation at Century occurs in the upper part of the Lawn Hill formation and is comprised of siltstones, shale and sandstone. Pyrite occurs immediately above the mineralised sequence, and throughout the footwall carbonaceous shale forming the lower proportion of the deposit. Zinc predominantly occurs as sphalerite (ZnS) and lead as galena (PbS). These sulfides are very fine-grained and may oxidise rapidly upon exposure. The pyrite, sphalerite and galena are the main potential sources of acid rock drainage (ARD) or heavy metal leachate at the mine site.To minimise the generation of ARD in the waste rock dumps, they are constructed in a specific manner and waste rock is classified into the following three classes based on competence and acid forming/consuming capabilities:Class 1: Competent rock, non-acid forming or acid-consuming material. Class 2: Non-competent, non-acid forming or acid-consuming material. Class 3: Acid-forming material. The generalised Waste Rock Dump Design for current operations comprises an outer zone of Class 1 material and inner zone with Class 2 and 3 material. Limestone is the Class 1 material used for both its structural support and acid neutralising capacity. Reserves of limestone at the mine site are limited. Net acid generation (NAG) tests confirm that a mix of limestone and shales can be net acid consuming.Field based and laboratory based trials have been established at PCML to quantify blending levels of limestone and shale that will produce leachates both neutral in pH and low in metal/salt concentrations. This paper will discuss the first six months results (of a two-year sampling program) from the trials.

Jan 1, 2004

By R Morrison, P Owen

Particle breakage is an essential part of mineral processing. The aim is to reduce run of mine mineral ore to an optimal size for liberating target minerals and for subsequent recovery by separation processes such as flotation. This size reduction is typically accomplished in a series of stages in a grinding circuit tailored to the properties of the particular mine ore. Commonly this involves two or more classes of equipment starting with crushers, followed by SAG mills and then sometimes ball mills. Occasionally, high pressure grinding rolls or other novel devices are substituted. Broadly, energy consumption increases and energy efficiency decreases with the fineness of the material produced by each piece of equipment. For many operations, up to 50 or 60 per cent of total greenhouse gas emissions from a plant arise from the operation of the comminution circuit with the majority produced by the finest grinding parts, such as the SAG and ball mills. Wear of mill liners and grinding media also add to greenhouse gas emissions generated by their manufacture. The need for continual cost reduction and increasing regulatory and social pressure relating to greenhouse emissions create a strong need for improvements in comminution energy efficiency. Traditional experimental and modelling approaches are not well placed to create the required insights into comminution fundamentals or facilitate radical step changes in performance. This paper discusses the role that advanced modelling (based on coupled DEM and CFD) can play in improving the energy efficiency and performance of existing mainstream grinding equipment and in the development of new ones with radically superior performance. Achieving this goal will also require an improved understanding of ore breakage and methods to include sufficiently realistic breakage models within the DEM models. Developmental issues for the modelling and the critical need for validation of the advanced model features are highlighted.

Jan 1, 2004

By Wright JK, Turner RE, Batterham RJ, Morrison AL

Simulation can play an important role in the design, optimization and control of complete industrial processes, the most appropriate method depending on the particular application. Most commonly, process models or simulators are means of representing the process which are either purely mathematical or physical. Mathematical models, however, almost invariably need to be based to some extent on experimental data or require experimental verification before they can be used with confidence. Ways in which experimental and mathematical modelling techniques can be combined to best effect are discussed, with reference to the simulation of iron ore induration and direct reduction processes. A novel method is presented for the simulation of direct reduction shaft furnaces. Small scale apparatus has been developed in which ore or pellet samples are subjected to the changing environment of the industrial process. The time dependent conditions (solid temperature and gas compositions) are provided by a mathematical representation of heat transfer and the conservation of mass and energy in the process Simulated.

Jan 1, 1986